Zinc speciation in fly ash from MSWI using XAS - novel insights and implications.

The chemical forms of zinc in fly ash from municipal solid waste incineration (MSWI) crucially affect ash management, influencing both material recovery options and the risk of unwanted leaching into ecosystems. The zinc speciation was investigated in fly ash samples sourced from full-scale MSWI plants, including four grate fired boilers (GB) and one fluidized bed boiler (FB). We applied X-ray Absorption Spectroscopy (XAS), and the spectra were analyzed against a unique library of over 30 relevant compounds, tailored to the nuances of zinc chemistry of fly ash. Nano-XANES and sequential leaching were employed as complementary analytical methods. Multiple chemical forms of zinc were found in the ash, whereof potassium zinc chloride salts (K2ZnCl4) emerged as the predominant form in GB fly ash representing 41-64 % of the zinc content, while less for FB fly ash (19 %). The mere exposure to humidity in the air during storage resulted in hydroxylation of the alkali zinc chlorides into Zn5(OH)8Cl2·H2O. Other forms of zinc in the ash were Zn4Si2O7(OH)2·H2O, ZnFe2O4, ZnAl2O4, surface adsorbed zinc, and Zn5(CO3)2(OH)6. Notably, the proportion of zinc in spinel forms (ZnFe2O4 and ZnAl2O4) increased threefold in FB ash compared to GB ash, representing ∼60 % and ∼10-20 % of the zinc, respectively.

Sustainable Valorisation of Sewage Sludge via Carbon Dioxide-Assisted Pyrolysis.

The escalating volume of sewage sludge (SS) generated poses challenges in disposal, given its potential harm to the environment and human health. This study explored sustainable solutions for SS management with a focus on energy recovery. Employing CO2-assisted pyrolysis, we converted SS into flammable gases (H2 and CO; syngas). Single-stage pyrolysis of SS in a CO2 conditions demonstrated that CO2 enhances flammable gas production (especially CO) through gas phase reactions (GPRs) with volatile matter (VM) at temperatures ≥ 520 ˚C. Specifically, the CO2 partially oxidized the VM released from SS and concurrently underwent reduction into CO. To enhance the syngas production at temperatures ≤ 520 ˚C, multi-stage pyrolysis setup with additional heat energy and a Ni/Al2O3 catalyst were utilized. These configurations significantly increased flammable gas production, particularly CO, at temperatures ≤ 520 ˚C. Indeed, the flammable gas yield in the catalytic pyrolysis of SS increased from 200.3 mmol under N2 conditions to 219.2 mmol under CO2 conditions, representing a 4.4-fold increase compared to single-stage pyrolysis under CO2 conditions (50.0 mmol). By integrating a water-gas-shift reaction, the flammable gases produced from CO2-assisted catalytic pyrolysis were expected to have the potential to generate revenue of US$4.04 billion. These findings highlight the effectiveness of employing CO2 in SS pyrolysis as a sustainable and effective approach for treating and valorising SS into valuable energy resources.

Recovery of gaseous fuels through CO2-mediated pyrolysis of thermosetting polymer waste.

Thermosetting polymers are used in a wide range of applications due to their robust mechanical strength and superior flame retardancy. Despite these technical benefits, recycling of thermosetting polymers has been challenging because of their crosslinking nature. Moreover, their disposal through conventional methods (landfill and combustion) poses environmental concerns, such as microplastics and air pollutants. To address these issues, this study introduces a thermo-chemical disposal platform for thermosetting polymer wastes that employs carbon dioxide (CO2) as a reactive medium. In this work, melamine-formaldehyde was used as model compound of thermosetting polymers. In single-stage pyrolysis, it was revealed that CO2 plays a crucial role in controlling in the compositional matrices of pyrolytic gases, liquid products, and wax. These compositional changes were attributed to the homogeneous reactions between CO2 and the volatile compounds released from the thermolysis of MF. To enhance the thermal cracking of the MF, a double-stage pyrolysis process was tested, which increased the production of pyrolytic gases and eliminated wax formation. However, the slow kinetics governing the reactivity of CO2 limits the occurrence of homogeneous reactions. A nickel-based catalyst was used to accelerate reaction kinetics. The catalytic pyrolysis under CO2 conditions led to substantial increases in syngas (H2 and CO) production of 880% and 460%, respectively, compared with double-stage pyrolysis. These findings demonstrate that thermosetting polymer wastes can be valorized into gaseous fuels through thermo-chemical process, and CO2 enhances the recovery of energy and chemicals. Therefore, this study presents an innovative technical platform to convert thermosetting polymer wastes and CO2 into syngas.

Co-pyrolysis of plastic waste and eucalyptus waste wood for fuel pellets production: A study of fuel, mechanical, and combustion characteristics under varying binder proportion.

The study explores the effect of varying molasses proportions as a binder on the characteristics of densified char obtained through the slow co-pyrolysis of plastic waste and Eucalyptus wood waste (Waste low-density polyethylene - Eucalyptus wood (WLDPE-EW) and Waste Polystyrene - Eucalyptus wood (WPS-EW)). Pyrolysis was conducted at 500 °C with a residence time of 120 min, employing plastic to wood waste ratios of 1:2 and 1:3 (w/w). The focus was on how varying the proportion of molasses (10-30 %), influences the physical and combustion properties of the resulting biofuel pellets. Our findings reveal that the calorific value of the pellets decreased from 28.94 to 27.44 MJ/Kg as the molasses content increased. However, this decrease in calorific value was compensated by an increase in pellet mass density, which led to a higher energy density overall. This phenomenon was attributed to the formation of solid bridges between particles, facilitated by molasses, effectively decreasing particle spacing. The structural integrity of the pellets, as measured by the impact resistance index, improved significantly (43-47 %) with the addition of molasses. However, a significant change in the combustion characteristics depicted by lower ignition and burnout temperatures were observed due to decrease in fixed carbon value and increase in volatile matter content, as the proportion of molasses increased. Despite these changes, the pellets demonstrated a stable combustion profile, suggesting that molasses are an effective binder for producing biofuel pellets through the densification of char derived from the co-pyrolysis of plastic and Eucalyptus wood waste. The optimized molasses concentration analyzed through multifactor regression analysis was 16.96 % with 28 % WLDPE proportion to produce WLDPE-EW char pellets. This study highlights the potential of using molasses as a sustainable binder to enhance the mechanical and combustion properties of biofuel pellets, offering a viable pathway for the valorization of waste materials.

Investigating the impact of alumina nanoparticles in coconut oil distillate biodiesel to lessen emissions in direct injection diesel engine.

Petroleum fuels are commonly used for automobiles. However, the continuous depletion and exhaust gas emission causes serious problems. So, there is a need for an alternative eco-friendly fuel. Biodiesel is a type of fuel manufactured through a process called transesterification, which involves converting vegetable oils into a usable form. The process parameters of the transesterification process were optimized using the Taguchi method to achieve maximum biodiesel yield. However, the main problem of biodiesel is its high cost which could be reduced by using low-cost feedstock. To address this challenge, biodiesel (BCFAD) is derived from coconut fatty acid distillate (CFAD), a by-product obtained from refining coconut oil. This work uses BCFAD and BCFAD with Alumina nanoparticles as fuels. Alumina nanoparticles in the mass fraction of 25 ppm, 50 ppm, and 100 ppm are dispersed in BCFAD. The investigation results reveal an increase of 6.5% in brake thermal efficiency for BCFAD with 100 ppm nanoparticles when compared to BCFAD. There is a reduction of 29.29% of hydrocarbon and 34% of Carbon monoxide emissions with BCFAD100 in comparison with diesel. However, there is a marginal increase in NOx emission with the increase in nanoparticles. The heat release rate and cylinder pressure of BCFAD100 are comparable to diesel fuel. It was concluded that the utilization of BCFAD with a nanoparticle dispersion of 100 ppm is suitable for direct use as fuel in diesel engines.

Techno-economic and environmental analysis of organic municipal solid waste for energy production.

Addressing the critical conundrum of escalating municipal solid waste (MSW) and shrinking landfill spaces in urban areas, this research pioneers a sustainable approach for Bangladesh by exploring the potential of biogas production from MSW. Distinctly, it fills the research gap by providing a detailed techno-economic and environmental analysis of decentralized fixed-dome anaerobic digestion facilities in the urban context of Chittagong, Bangladesh, a domain previously underexplored. Our findings demonstrate the feasibility of converting MSW into a renewable energy source, offering an innovative solution that simultaneously tackles waste management and energy generation challenges. Each proposed plant showcases the capability to generate 536 m³ of biogas daily, sufficient to power a 50 kW gas engine and supply 44 households, thereby contributing significantly to urban waste reduction and CO2 emissions mitigation by approximately 500 tons monthly. The economic analysis reveals an attractive investment payback period of two years, underscoring the model's viability and its potential as a replicable framework for similar urban settings grappling with waste management crises. This study not only bridges a critical knowledge gap but also introduces a novel, sustainable waste-to-energy model, marking a pivotal step towards achieving energy security and environmental sustainability in developing nations.

Transforming Waste into Wealth: Advanced Carbon-Based Electrodes Derived from Refinery and Coal By-Products for Next-Generation Energy Storage.

This comprehensive review addresses the need for sustainable and efficient energy storage technologies against escalating global energy demand and environmental concerns. It explores the innovative utilization of waste materials from oil refineries and coal processing industries as precursors for carbon-based electrodes in next-generation energy storage systems, including batteries and supercapacitors. These waste-derived carbon materials, such as semi-coke, coal gasification fine ash, coal tar pitch, petroleum coke, and petroleum vacuum residue, offer a promising alternative to conventional electrode materials. They present an optimal balance of high carbon content and enhanced electrochemical properties while promoting environmental sustainability through effectively repurposing waste materials from coal and hydrocarbon industries. This review systematically examines recent advancements in fabricating and applying waste-derived carbon-based electrodes. It delves into the methodologies for converting industrial by-products into high-quality carbon electrodes, with a particular emphasis on carbonization and activation processes tailored to enhance the electrochemical performance of the derived materials. Key findings indicate that while higher carbonization temperatures may impede the development of a porous structure, using KOH as an activating agent has proven effective in developing mesoporous structures conducive to ion transport and storage. Moreover, incorporating heteroatom doping (with elements such as sulfur, potassium, and nitrogen) has shown promise in enhancing surface interactions and facilitating the diffusion process through increased availability of active sites, thereby demonstrating the potential for improved storage capabilities. The electrochemical performance of these waste-derived carbon materials is evaluated across various configurations and electrolytes. Challenges and future directions are identified, highlighting the need for a deeper understanding of the microstructural characteristics that influence electrochemical performance and advocating for interdisciplinary research to achieve precise control over material properties. This review contributes to advancing electrode material technology and promotes environmental sustainability by repurposing industrial waste into valuable resources for energy storage. It underscores the potential of waste-derived carbon materials in sustainably meeting global energy storage demands.

A comprehensive comparative study on microwave- assisted pyrolysis products derived from raw and digested organic waste, with emphasis on sewage sludge, food waste, and livestock manure.

This study focused on characterizing sewage sludge, food waste, and livestock manure, representative of continuously generated organic wastes, along with their anaerobic digestion residues. Microwave assisted pyrolysis was employed to investigate the relationship between the properties of the raw organic wastes and the resulting pyrolysis products, utilizing the R-program for analysis. Evaluation of the pyrolysis products of these six organic wastes revealed that char yield was primarily influenced by ash and fixed carbon contents, with higher yields observed in residues from anaerobic digestion compared to the original organic waste. Liquid and gaseous product quantities were found to increase with volatile content, while high-fat content within the volatile fraction notably enhanced liquid product yields, impacting syngas production. Analysis of syngas composition indicated a negative correlation between high nitrogen content in the feedstock and H2 generation. Furthermore, examining the correlation between chemical properties of organic waste and pyrolysis products revealed a proportional increase in protein components with nitrogen content, suggesting potential improvements in pyrolysis efficiency through raw material pretreatment enhancements by the R program.

Use of Honey Bees and Hive Products as Bioindicators to Assess Environmental Contamination in Targeted Areas of the Campania Region (Italy).

In recent years, biomonitoring has gained more attention, particularly when assessing the environmental health of significant areas, such as those near waste-to-energy facilities. These requirements coincide with the chance to detect environmental pollutants using sensitive organisms. Bees were shown to be quite effective in evaluating the presence of certain compounds by analyzing their associated matrices, such as pollen, honey, or wax. In our study, we employed the honey bee (Apis mellifera) as an indicator to initially monitor the vicinity of the waste-to-energy plant in Acerra, which is situated in the Campania region of Italy. The primary aim was to determine whether the facility was accountable for any environmental releases of dioxins or dioxin-like compounds. Then, we assessed the presence of additional pollutants in the same area, including trace elements, polycyclic aromatic hydrocarbons, and pesticides, released by human activities. To obtain further information about environmental quality, a second biomonitoring station was installed near the Caivano S.T.I.R. (Waste Shredding, Sifting, and Packaging Plant). The results showed the dioxin levels did not exceed predetermined limitations at the Acerra site, thus demonstrating the efficacy of the waste-to-energy facility and the bees' ability to detect the presence of other pollutants. Additionally, this biomonitoring system exhibited sensitivity to environmental variations, thereby enabling the evaluation of xenobiotic flux between two proximate zones and across temporal scales. This pioneering study suggests the advantages of utilizing bees to detect a wide range of contaminants, thereby providing valuable insights into environmental quality and potential health risks for both ecosystems and human populations.

Plastic waste management through liquefaction in hydrogen donating solvents: A review.

Plastic pollution poses a significant environmental threat, particularly to marine ecosystems, as conventional plastics persist without degradation, accumulating plastic waste in landfills and natural environments. A promising alternative to address this issue involves the use of hydrogen donor solvents in plastic liquefaction, offering a dual benefit of waste reduction and the generation of valuable liquid products with diverse industrial applications. This review delves into plastic recycling methods with a specific focus on liquefaction using hydrogen donating solvents as an innovative approach to waste management. Liquefaction, conducted at moderate to high temperatures (280-450 °C) and pressures (7-30 MPa), yields high oil conversion using various solvents. This study examined the performance of hydrogen-donating solvents, including water, alcohols, decalin, and cyclohexane, in enhancing the oil yield while minimising the oxygen content. Supercritical water, recognised for its effective plastic degradation and chemical production capabilities, and alcohols, with their alkylating and hydrogen-donating properties, have emerged as key solvents in plastic liquefaction. The use of hydrogen donor solvents stabilizes the free radicals, enhancing the conversion of plastic waste into valuable products. In addition, this review addresses the economic efficiency of the liquefaction process.

Incineration-source fingerprints and emission spectrums of dioxins with diagnostic application.

Despite increasing waste-to-energy (WtE) capacities, there remain deficiencies in comprehension of 136 kinds of tetra- through octa-chlorinated dibenzo-p-dioxin and dibenzofurans (136 PCDD/Fs) originating from incineration sources. Samples from twenty typical WtE plants, encompassing coal-fired power plants (CPP), grate incinerators (GI), fluidized bed incinerators (FBI), and rotary kilns (RK), yielded extensive PCDD/F datasets. Research was conducted on fingerprint mapping, formation pathways, emission profiles, and diagnostic analysis of PCDD/Fs in WtE plants. Fingerprints revealed a prevalence of TCDF, followed by PeCDF, while CPP and RK respectively generated more PCDD and HxCDD. De novo synthesis was the predominant formation pathway except one plant, where CP-route dominated. DD/DF chlorination also facilitated PCDD/F formation, showing general trends of FBI > GI > CPP > RK. The PCDD/F emission intensities emitted in air pollution control system inlet (APCSI) and outlet (APCSO) followed the statistical sequence of RK > FBI > GI > CPP, with the average I-TEQ concentrations in APCSO reaching 0.18, 0.08, 0.11, and 0.04 ng I-TEQ·Nm-3. Emission spectrum were accordingly formed. Four clusters were segmented for diagnosis analysis, where PCDD/Fs in GI and FBI were similar, grouped as a single cluster. PCDD/Fs in CPP and RK demonstrated distinctive features in TCDD, HxCDD, and HxCDF. The WtE plants exceeding the limit value tended to generate and retain fewer TCDD and TCDF yet had higher fractions of HxCDD and HxCDF. The failure of APCS coupled with the intrinsic source strength of PCDD/Fs directly led to exceedance, highlighting safe operational practices. This study motivated source tracing and precise evaluation of 136 PCDD/Fs based on the revealed fingerprint profiles for WtE processes.

Characteristics of hydrogen energy yield in steam gasification of coffee residues.

Coffee residues (CRs) were gasified using a laboratory-scale fluidized bed gasifier with an air/steam mixture as the carrier gas. The gasification was conducted at an equivalence ratio (ER) of 0.3, and different operation temperatures (700, 800, and 900 °C) and steam-to-biomass (S/B) ratios (0, 0.75, and 1.5) were applied. Increasing temperature without steam boosted H2 and CO concentrations in producer gas, raising lower heating value (LHV) and cold gas efficiency (CGE) through endothermic reactions like Boudouard, tar cracking, and water-gas formation. At 900 °C, gas had LHV of 3.76 MJ/Nm3 and CGE of 22.47%. It was elevating temperature from 700 to 900 °C and S/B ratio to 1.5 raised H2 and CO concentrations from 2.04 to 8.60% and from 9.56 to 11.8%, respectively. This also increased LHV from 2.23 to 3.89 MJ/Nm3 and CGE from 11.28 to 25.08%. The steam gasification reaction was found to increase the H2 concentration and was thus considered effective in converting CRs to syngas and increasing energy production. Overall, the study successfully demonstrated the feasibility of steam gasification as a means of converting coffee residues to syngas and increasing energy production. The results also highlighted the importance of operating temperature and S/B ratio in improving the gasification process.

Eggshells & Eggshell Membranes- A Sustainable Resource for energy storage and energy conversion applications: A critical review.

As the world strives to achieve a sustainable future, the exploration of alternative and renewable raw materials for energy storage and energy conversion has gained significant attention. A growing trend on "Waste to Energy" approach has attained prominence. Accordingly, chicken eggshells, a residual from poultry industry, have emerged as a promising candidate due to their abundant availability, low cost, and unique physical and chemical properties. This review article presents an overview of recent advancements in utilizing eggshell waste for energy storage and energy conversion applications. It discusses the transformation of eggshells usage into functional materials, along with their performance in various energy-related applications. The potential of eggshell-based materials in improving energy efficiency and reducing environmental impact is highlighted, providing insights into the future prospects of this sustainable resource.

Pressurized pyrolysis of mattress residue: An alternative to landfill management.

Mattresses are a difficult waste to manage in landfills due to their large volume and low density. Pyrolysis treatment could reduce its volume while producing fuel or products valuable for the chemical industry. Pressurized pyrolysis at 400, 450, and 500 °C is carried out in a lab-scale autoclave at initial pressures 4.2, 8.4, and 16.8 bar. Product gas yield increases slightly along with elevated pressure as well as temperature. However, beyond 8.4 bar the initial pressure makes no discernible differences. CO and CO2 are the major gas species followed by CH4. CO contributes the most to the product gas energy content followed by C3 species, C2H6, and H2. Calculated energy content (heating value) is between 2 and 15 MJ·Nm-3. In terms of product gas energy content, low pressure pyrolysis is favorable over high pressure pyrolysis. According to integration areas of chromatographic measurements the liquid phase contains up to 25 % of N-compounds, with benzonitrile being the most abundant, followed by toluene, o-xylene, and ethylbenzene. The solid char maintains constant properties across operating conditions, with carbon and energy contents of approximately 75 wt% and 30 MJ·kg-1, respectively.

Turning trash into treasure: Torrefaction of mixed waste for improved fuel properties. A case study of metropolitan city.

Solid waste management is one of the biggest challenges of the current era. The combustible fractions in the waste stream turn out to be a good energy source if converted into refuse-derived fuel. Researchers worldwide are successfully converting it into fuel. However, certain challenges are associated with its application in gasifiers, boilers, etc. to co-fire it with coal. These include high moisture content, low calorific value, and difficulty to transport and store. The present study proposed torrefaction as a pretreatment of the waste by heating it in the range of 200 °C-300 °C in the absence of oxygen at atmospheric pressure. The combustible fraction from the waste stream consisting of wood, textile, paper, carton, and plastics termed as mixed waste was collected and torrefied at 225 °C, 250 °C, 275 °C, and 300 °C for 15 and 30 min each. It was observed that the mass yield and energy yield decreased to 45% and 62.96% respectively, but the energy yield tended to increase by the ratio of 1.39. Proximate analysis showed that the moisture content and volatile matter decreased for torrefied samples, whereas the ash content and fixed carbon content increased. Similarly, the elemental analysis revealed that the carbon content increased around 23% compared to raw samples with torrefaction contrary to hydrogen and oxygen, which decreased. Moreover, the higher heating value (HHV) of the torrefied samples increased around 1.3 times as compared to the raw sample. This pretreatment can serve as an effective solution to the current challenges and enhance refuse-derived fuel's fuel properties.

Characterization of lightweight aerated mortars using waste-to-energy bottom ash (WtE-BA) as aerating agent.

The management of Waste-to-Energy Bottom Ash (WtE-BA), generated during the incineration of waste, poses a global challenge. Presently, the majority of WtE-BA is disposed of in landfills due to the lack of alternatives. Meanwhile, the construction industry remains the primary consumer of raw materials and significantly contributes to Greenhouse Gas Emissions. This study attempts to address these issues by utilizing the fine fraction of WtE-BA (<2 mm) as a raw material for aerated mortar production. Thanks to its metallic aluminum content, WtE-BA is utilized as an aerating agent. The study investigates how the quantities of water and WtE-BA, as well as its granulometric sub-fractions, impact the properties of the final product. An analysis of properties such as density, compressive strength, and thermal conductivity was conducted. Additionally, the environmental impact of each raw material (i.e. WtE-BA, cement and sand) was assessed through leaching tests and elemental content analysis enabling the determination of their individual contribution to the presence of trace elements in the produced mortars. The aforementioned properties are discussed using microstructure and porosity analyses. The findings demonstrate that the quantity of water is a crucial factor in controlling the aeration of mortars, whereas the granulometry of the WtE-BA particles did not significantly affect their macro-properties. Furthermore, this study highlights that WtE-BA based mortars has the potential to exhibit better environmental and insulating performances than standard aerated mortar of equal density and strength. The differences in pore size and type between WtE-BA and aerated mortars can account for the variation in performance. Thus, WtE-BA proves to be an effective substitute for aerating agent in the production of aerated mortars.

Thermochemical conversion of silkworm by-product into syngas.

This study explored the valorisation of silkworm by-product, a major by-product of the silk industry (sericulture), which amounts to 16 million tonnes annually. The focus was on transforming waste into energy resources through pyrolysis under CO2 conditions. In one-stage pyrolysis, the evolution of syngas under N2 was found to be comparable to that under CO2. A notable allocation of carbon to biocrude rather than syngas was observed. The two-stage pyrolysis resulted in increased syngas production. However, achieving a homogeneous reaction between CO2 and the volatiles liberated from silkworm byproduct proved challenging. Indeed, the reaction kinetics governing CO2 reactivity was not fast although the temperature windows of the reaction were aligned in the two-stage pyrolysis. To address this issue, pyrolysis was performed using a Ni-based catalyst to expedite the reaction kinetics. Consequently, syngas formation, particularly CO formation, was significantly enhanced under CO2 conditions compared to that under N2 conditions. The syngas yield under CO2 was 36.42 wt% which was 2-fold higher than that of N2. This suggested the potential of CO2 altering the carbon distribution from biocrude to syngas. This strategy would contribute to the establishment of sustainable production of silk by converting sericulture by-product into energy/chemical resources.

Investigating the characteristics of combustible fraction of legacy waste: A study on energy recovery potential and GHG emission quantification.

In India, majority of the generated municipal solid waste (MSW) was dumped in poorly managed landfills and dumpsites over the past decades and is an environmental and health hazard. Landfill mining is a promising solution to reclaim these sites along with the recovery of resources (materials and energy). During landfill mining operations, the combustible fraction is one of the major components recovered and needs proper management for maximizing resource recovery. For the identification of appropriate resource recovery options, knowledge of the physicochemical characteristics is required. The present study aims to assess the depth-wise change in the composition of legacy waste and the physicochemical characteristics of the combustible fraction. Furthermore, a material flow analysis considering the incineration of combustible fraction was performed to estimate the energy generation potential and the associated greenhouse gas (GHG) emissions. The results of the compositional analysis of dry legacy waste revealed that the fine fraction (<4 mm soil-like material) was dominating with a share of 36%. The depth-wise analysis showed a decrease in the calorific value with increasing landfill depth, while no specific trend was observed for the other parameters analyzed, including proximate and ultimate analysis, and chlorine content. The material flow analysis performed for 100 tonnes of wet legacy waste indicated that 52 tonnes of waste is combustible fraction. The GHG emissions through incineration of one tonne of dry combustible fraction would be 1389 kg CO2-eq, with 1125 kWh of electrical energy generation potential.

Valorization of crop residues and animal wastes: Anaerobic co-digestion technology.

To switch the over-reliance on fossil-based resources, curb environmental quality deterioration, and promote the use of renewable fuels, much attention has recently been directed toward the implementation of sustainable and environmentally benign 'waste-to-energy' technology exploiting a clean, inexhaustible, carbon-neutral, and renewable energy source, namely agricultural biomass. From this perspective, anaerobic co-digestion (AcoD) technology emerges as a potent and plausible approach to attain sustainable energy development, foster environmental sustainability, and, most importantly, circumvent the key challenges associated with mono-digestion. This review article provides a comprehensive overview of AcoD as a biochemical valorization pathway of crop residues and livestock manure for biogas production. Furthermore, this manuscript aims to assess the different biotic and abiotic parameters affecting co-digestion efficiency and present recent advancements in pretreatment technologies designed to enhance feedstock biodegradability and conversion rate. It can be concluded that the substantial quantities of crop residues and animal waste generated annually from agricultural practices represent valuable bioenergy resources that can contribute to meeting global targets for affordable renewable energy. Nevertheless, extensive and multidisciplinary research is needed to evolve the industrial-scale implementation of AcoD technology of livestock waste and crop residues, particularly when a pretreatment phase is included, and bridge the gap between small-scale studies and real-world applications.

Waste-to-energy barriers and solutions for developing countries with limited water and energy resources.

The environmental risks of conventional waste disposal methods, along with the resource and energy value of waste, have formed the foundation for waste-to-energy (WtE) technology. WtE systems that work on recovering energy present a suitable solution to generate energy and sustainably manage waste. This type of waste management system in the Middle East and North Africa (MENA) region is still considered underutilized as WtE technology is rarely used due to a lack of experience in their specific local conditions, lack of qualified competencies, and the absence of an appropriate regulatory and legislative structure. This study reviews the existing WtE policies and regulations, and it investigates the potential of WtE techniques in the MENA region. Moreover, sustainability in water consumption is critical; therefore, various water-conservation techniques were reviewed and considered when selecting regulatory actions. The radiative sky cooling technique was recommended to reduce water consumption. Barriers to implementing WtE and solutions for developing countries were presented to enable proper WtE implementation.