Nacre-Mimetic Structure Multifunctional Ion-Conductive Hydrogel Strain Sensors with Ultrastretchability, High Sensitivity, and Excellent Adhesive Properties.

Recently, conductive hydrogels have emerged as promising materials for smart, wearable devices. However, limited mechanical properties and low sensitivity greatly restrict their lifespan. Based on the design of biomimetic-layered structure, the conductive hydrogels with nacre-mimetic structure were prepared by using layered acrylic bentonite (AABT) and phytic acid (PA) as multifunctional "brick" and "mortar" units. Among them, the unique rigid cyclic multihydroxyl structure of the "organic mortar" PA preserves both ultrastretchability (4050.02%) and high stress (563.20 kPa) of the hydrogel, which far exceeds most of the reported articles. Because of the synergistic effect of AABT and PA, the hydrogel exhibits an excellent adhesive strength (87.74 kPa). The role of AABT in the adhesive properties of hydrogels is proposed for the first time, and a general strategy for improving the adhesive properties of hydrogels by using AABT is demonstrated. Furthermore, AABT provides ion channels and PA ionizes abundant H+, conferring a high gauge factor (GF = 14.95) and excellent antimicrobial properties to the hydrogel. Also, inspired by fruit batteries, simple self-powered flexible sensors were developed. Consequently, this study provides knowledge for functional bentonite filler modified hydrogel, and the prepared multifunctional ionic conductive hydrogel shows great application potential in the field of intelligent wearable devices.

Enhancing Alginate Hydrogels as Possible Wound-Healing Patches: The Synergistic Impact of Reduced Graphene Oxide and Tannins on Mechanical and Adhesive Properties.

Hydrogels are three-dimensional crosslinked materials known for their ability to absorb water, exhibit high flexibility, their biodegradability and biocompatibility, and their ability to mimic properties of different tissues in the body. However, their application is limited by inherent deficiencies in their mechanical properties. To address this issue, reduced graphene oxide (rGO) and tannins (TA) were incorporated into alginate hydrogels (Alg) to evaluate the impact of the concentration of these nanomaterials on mechanical and adhesive, as well as cytotoxicity and wound-healing properties. Tensile mechanical tests demonstrated improvements in tensile strength, elastic modulus, and toughness upon the incorporation of rGO and TA. Additionally, the inclusion of these materials allowed for a greater energy dissipation during continuous charge-discharge cycles. However, the samples did not exhibit self-recovery under environmental conditions. Adhesion was evaluated on pig skin, revealing that higher concentrations of rGO led to enhanced adhesion, while the concentration of TA did not significantly affect this property. Moreover, adhesion remained consistent after 10 adhesion cycles, and the contact time before the separation between the material and the surface did not affect this property. The materials were not cytotoxic and promoted healing in human fibroblast-model cells. Thus, an Alg/rGO/TA hydrogel with enhanced mechanical, adhesive, and wound-healing properties was successfully developed.

Bioglass/ceria nanoparticle hybrids for the treatment of seroma: a comparative long-term study in rats.

Background: Seroma formation is a common postoperative complication. Fibrin-based glues are typically employed in an attempt to seal the cavity. Recently, the first nanoparticle (NP)-based treatment approaches have emerged. Nanoparticle dispersions can be used as tissue glues, capitalizing on a phenomenon known as 'nanobridging'. In this process, macromolecules such as proteins physically adsorb onto the NP surface, leading to macroscopic adhesion. Although significant early seroma reduction has been shown, little is known about long-term efficacy of NPs. The aim of this study was to assess the long-term effects of NPs in reducing seroma formation, and to understand their underlying mechanism. Methods: Seroma was surgically induced bilaterally in 20 Lewis rats. On postoperative day (POD) 7, seromas were aspirated on both sides. In 10 rats, one side was treated with NPs, while the contralateral side received only NP carrier solution. In the other 10 rats, one side was treated with fibrin glue, while the other was left untreated. Seroma fluid, blood and tissue samples were obtained at defined time points. Biochemical, histopathological and immunohistochemical assessments were made. Results: NP-treated sides showed no macroscopically visible seroma formation after application on POD 7, in stark contrast to the fibrin-treated sides, where 60% of the rats had seromas on POD 14, and 50% on POD 21. At the endpoint (POD 42), sides treated with nanoparticles (NPs) exhibited significant macroscopic differences compared to other groups, including the absence of a cavity, and increased fibrous adhesions. Histologically, there were more macrophage groupings and collagen type 1 (COL1) deposits in the superficial capsule on NP-treated sides. Conclusion: NPs not only significantly reduced early manifestations of seroma and demonstrated an anti-inflammatory response, but they also led to increased adhesion formation over the long term, suggesting a decreased risk of seroma recurrence. These findings highlight both the adhesive properties of NPs and their potential for clinical therapy.

Network Polymer Properties Engineered Through Polymer Backbone Dispersity and Structure.

Dispersity (Ð or Mw/Mn) is an important parameter in material design and as such can significantly impact the properties of polymers. Here, polymer networks with independent control over the molecular weight and dispersity of the linear chains that form the material are developed. Using a RAFT polymerization approach, a library of polymers with dispersity ranging from 1.2-1.9 for backbone chain-length (DP) 100, and 1.4-3.1 for backbone chain-length 200 were developed and transformed to networks through post-polymerization crosslinking to form disulfide linkers. The tensile, swelling, and adhesive properties were explored, finding that both at DP 100 and DP 200 the swelling ratio, tensile strength, and extensibility were superior at intermediate dispersity (1.3-1.5 for DP 100 and 1.6-2.1 for DP 200) compared to materials with either substantially higher or lower dispersity. Furthermore, adhesive properties for materials with chains of intermediate dispersity at DP 200 revealed enhanced performance compared to the very low or high dispersity chains.

Synthesis, Characterization and Catechol-Based Bioinspired Adhesive Properties in Wet Medium of Poly(2-Hydroxyethyl Methacrylate-co-Acrylamide) Hydrogels.

Hydrogels consist of crosslinked hydrophilic polymers from which their mechanical properties can be modulated for a wide variety of applications. In the last decade, many catechol-based bioinspired adhesives have been developed following the strategy of incorporating catechol moieties into polymeric backbones. In this work, in order to further investigate the adhesive properties of hydrogels and their potential advantages, several hydrogels based on poly(2-hydroxyethyl methacrylate-co-acrylamide) with N'N-methylene-bisacrylamide (MBA), without/with L-3,4-dihydroxyphenylalanine (DOPA) as a catecholic crosslinker, were prepared via free radical copolymerization. 2-Hydroxyethyl methacrylate (HEMA) and acrylamide (AAm) were used as comonomers and MBA and DOPA both as crosslinking agents at 0.1, 0.3, and 0.5 mol.-%, respectively. The polymeric hydrogels were characterized by Fourier transform infrared spectroscopy (FT-IR), thermal analysis and swelling behavior analysis. Subsequently, the mechanical properties of hydrogels were determined. The elastic properties of the hydrogels were quantified using Young's modulus (stress-strain curves). According to the results herein, the hydrogel with a feed monomer ratio of 1:1 at 0.3 mol.-% of MBA and DOPA displayed the highest rigidity and higher failure shear stress (greater adhesive properties). In addition, the fracture lap shear strength of the biomimetic polymeric hydrogel was eight times higher than the initial one (only containing MBA); however at 0.5 mol.-% MBA/DOPA, it was only two times higher. It is understood that when two polymer surfaces are brought into close contact, physical self-bonding (Van der Waals forces) at the interface may occur in an -OH interaction with wet contacting surfaces. The hydrogels with DOPA provided an enhancement in the flexibility compared to unmodified hydrogels, alongside reduced swelling behavior on the biomimetic hydrogels. This approach expands the possible applications of hydrogels as adhesive materials, in wet conditions, within scaffolds that are commonly used as biomaterials in cartilage tissue engineering.

Research Progress of Polydopamine Hydrogel in the Prevention and Treatment of Oral Diseases.

Oral diseases represent one of the most prevalent diseases globally and are associated with serious health and economic burdens, greatly altering the quality of life of affected individuals. Various biomaterials play important roles in the treatment of oral diseases. To some extent, the development of biomaterials has promoted progress in clinically available oral medicines. Hydrogels have unique tunable advantages that make them useful in the next generation of regenerative strategies and have been widely applied in both oral soft and hard tissues repair. However, most hydrogels lack self-adhesive properties, which may result in low repair efficacy. Polydopamine (PDA), the primary adhesive component, has attracted increasing attention in recent years. PDA-modified hydrogels exhibit reliable and suitable adherence to tissues and easily integrate into tissues to promote repair efficiency. This paper reviews the latest research progress on PDA hydrogels and elaborates on the mechanism of the reaction between PDA functional groups and hydrogels, and summarizes the biological properties and the applications of PDA hydrogels in the prevention and treatment of the field of oral diseases. It is also proposed that in future research we should simulate the complex microenvironment of the oral cavity as much as possible, coordinate and plan various biological events rationally, and realize the translation from scientific research to clinical practice.

Influence of Illite and Its Amine Modifications on the Self-Adhesive Properties of Silicone Pressure-Sensitive Adhesives.

Obtaining new silicone self-adhesive in the presence of modified illite has been described. The filler was modified with N,N,4-trimethylaniline. The effect of illite content and modification on functional properties (adhesion, cohesion, stickiness, and shrinkage) was determined. Additionally, the thermal resistance (the SAFT test) of obtained silicone pressure-sensitive adhesives was evaluated. For all the systems tested, an increase in thermal resistance and shrinkage decrease were noted. Moreover, only a slight adhesion and tack decrease was revealed. Such self-adhesives could be applied for joining elements operating at increased temperatures, e.g., in heavy industry.

Effect of Low-Temperature Plasma Surface Treatment on Bonding Properties of Single-Lap Joint of Thermosetting Composites.

Bonding is one of the main forms of composite bonding. In order to investigate the effect of low-temperature plasma surface treatment on the bonding properties of carbon fiber-reinforced epoxy resin composites (CF/EP), a single-lap joint of CF/EP was prepared. The surface of the CF/EP was treated with atmospheric pressure "low-temperature plasma spray" equipment, and the tensile shear strength, surface morphology, surface contact angle and surface chemical composition of the CF/EP before and after plasma treatment were characterized. Finally, the samples were treated with traditional sandblasting, compared and analyzed. The results show that the effect of low-temperature plasma surface treatment on CF/EP joints is better than that of traditional sandblasting treatment. After low-temperature plasma surface treatment, the tensile shear strength of the CF/EP single-lap joint increased by 119.59% at most, and the failure form of the joint changed from untreated interface failure to mixed failure dominated by cohesion failure. Plasma can etch the surface of composite materials, the mechanical interlock between the carbon fiber and glue is enhanced and the bonding performance of the composite is improved. In addition, after low-temperature plasma surface treatment, the introduction of a large number of oxygen-containing active groups such as C-O and C=O can increase the surface free energy, reduce the contact angle and improve the surface activity and wettability of the composites. However, too long a treatment time will lead to excessive plasma etching of carbon fibers, thus weakening the active effect of the oxygen-containing active groups on the surface of the composites, and the surface wettability is no longer improved, but the adhesive properties of CF/EP are reduced. This paper plays a guiding role in the bonding technology of composite materials.

Influence of Acid-Modified Clinoptilolite on the Self-Adhesive Properties of Silicone Pressure-Sensitive Adhesives.

The preparation of a new "eternally alive adhesive" based on silicone pressure-sensitive adhesives with clinoptilolite is presented. Neat and acid-modified (i.e., treated with sulfuric acid (VI)) clinoptilolite was used. The effect of clinoptilolite acid treatment on the adhesive properties of pressure-sensitive adhesive tapes was tested. The obtained tapes exhibited increased thermal resistance when compared to the reference tapes. Despite introducing the filler, the pressure-sensitive adhesive tapes maintained good functional properties. The new self-adhesive materials show promising implementation potential where increased thermal resistance is required.

Effectiveness of Surface Treatment on Bonding Performance of Starch-Based Aqueous Polymer Isocyanate Wood Adhesive.

The surface of a bonding material plays a key role in the bonding performance of an adhesive. Herein, we evaluated the effect of substrate surface treatment methods (sandpaper polished, chemical oxidation, and coupling agent) on the adhesive properties of starch-based aqueous polymer isocyanate (API) wood adhesive during hygrothermal aging. The birch substrate was processed with three different surface treatments, and the change of surface was analyzed by X-ray Photoelectron Spectroscopy (XPS), Fourier Transform Infrared spectroscopy (FT-IR), and Energy Dispersive Spectroscopy (EDS) methods. The results showed that the surface treatment had a great influence on the change of the shear strength of glued wood under hygrothermal conditions, and the silane coupling agent treatment could effectively reduce the decrease in the compressive shear strength of the adhesive. An XPS analysis indicated that the chemical oxidation modified wood surface polarity, and the coupling agent treatment in the wood surface formed a transition layer. After hygrothermal aging treatment, due to the different surface treatment of adhesive joint surface binding energy, the internal water absorption rate of starch-based API adhesives exhibited different failure modes of the adhesive joint. These findings indicate that the surface treatment effectively improved the durability of the adhesive joints.

Assessment of Surface Treatment Degree of Steel Sheets in the Bonding Process.

The aim of the paper is to determine the influence of the surface treatment on the adhesive properties of steel sheet surfaces and the strength of the adhesive joints of steel sheets. The paper also aims to assess the degree of steel sheets' surface treatment in the bonding process. Due to the many methods of surface treatment and types of materials, the assessment of the surface treatment method is extremely important in adhesive processes. Two variants of the surface treatment were used: without a paint coating and with a paint coating, divided into two groups (without degreasing and with degreasing). Additionally, in the case of the analysis of the steel samples without the paint coating, mechanical treatment was applied. Two-component epoxy adhesive, prepared on the basis of bisphenol A and a polyamide curing agent, was used to prepare the single-lap adhesive joints of the steel sheets. The tests determined: (i) the adhesive properties of the steel sheets' surface based on the measurement of the contact angle of polar and apolar liquids (including wettability, work of adhesion, and surface free energy), (ii) surface roughness parameters (PN EN ISO 4287), and (iii) mechanical properties (load capacity and shear strength) of the steel sheets' adhesive joints (EN DIN 1465). Contact angle measurements of the steel sheet surfaces showed that the polar liquid better reflects the obtained strength results of the analyzed adhesive joints than the apolar liquid. Furthermore, better wettability of the surface of steel sheets with both polar and apolar liquids was obtained for samples whose surface was subjected to degreasing. It can also be concluded that the wettability of the surface can be used as one of the indicators of the degree of the surface treatment for the bonding process.

Comparison of Two-Component Silyl-Terminated Polyether/Epoxy Resin Model and Complete Systems and Evaluation of Their Mechanical, Rheological and Adhesive Properties.

The current research is devoted to the investigation of the influence of a secondary amine compatibilizer and customized additive package on the tensile, rheological and adhesive properties of a Silyl-terminated polyether (SIL)/Epoxy resin (EP) model and completed two-component systems. A SIL/EP model and completed two-component systems were developed over a broad range of the both pre-polymer ratios (90/10-30/70 wt.-to-wt%). Additive packages of the components A and B were designed to prevent premature polycondensation of the respective pre-polymers (including suitable catalysts for each of the pre-polymers, as well as vinyltrimetoxysilane as a drying agent for moisture control), to ensure easy processing and stable performance of the system. Results of the investigation testify that the values of the tensile strength and Shore-A hardness of the compatibilized systems are higher in comparison to unmodified ones. In the presence of the additive package, a further improvement of tensile strength and tensile strain values is observed for SIL-rich compositions (SIL content above 70 wt%), whereas at lower SIL concentrations, the reinforcing effect is considerably reduced. In respects to adhesion properties, the highest values to a broad range of substrates with different surface polarities are observed at the SIL/EP range from 80/20 to 50/50 wt.-to-wt%.

A Repeatable Self-Adhesive Liquid-Free Double-Network Ionic Conductor with Tunable Multifunctionality.

Liquid-free ionic conductors (LFICs) have promising applications in flexible electronics because most ionic conductors currently suffer from ionic liquid leakage or water evaporation issues. However, it has been a formidable challenge for LFICs to achieve long-term repeated self-adhesion on different substrates, especially on soft biological tissues. Based on the double-network design concept, we first fabricate a series of repeatable self-adhesive liquid-free double-network ionic conductors (SALFDNICs), consisting of stretchable first poly(AA-ChCl)-type supramolecular deep eutectic polymer networks and stiff second polydopamine (PDA) networks, which can maintain sufficient dynamic hydrogen bonds and catechol groups in the ionic conductors by preventing the overoxidation of dopamine, thus balancing the contradiction between adhesion and cohesion in liquid-free ionic conductors. Therefore, SALFDNICs can instantly form various interface interaction forces with multiple substrates (adhesion strength up to 757 N/m) and firmly adhere to various substrates for 20 detachment-reattachment cycles with a reduction in adhesion strength of less than 15%. Furthermore, SALFDNICs also have other comprehensive properties, such as optimum self-healing properties (self-healing efficiency of 90%), good stretchability (strain at break of 1200%), and promising conductivity (2.31 × 10-2 S m-1). Therefore, we believe that the extraordinary performance of SALFDNICs is important for improving device integration and the further development of flexible electronics.

Self-Healable, Strong, and Tough Polyurethane Elastomer Enabled by Carbamate-Containing Chain Extenders Derived from Ethyl Carbonate.

Commercial diol chain extenders generally could only form two urethane bonds, while abundant hydrogen bonds were required to construct self-healing thermoplastic polyurethane elastomers (TPU). Herein, two diol chain extenders bis(2-hydroxyethyl) (1,3-pheny-lene-bis-(methylene)) dicarbamate (BDM) and bis(2-hydroxyethyl) (methylenebis(cyclohexane-4,1-diy-l)) dicarbamate (BDH), containing two carbamate groups were successfully synthesized through the ring-opening reaction of ethylene carbonate (EC) with 1,3-benzenedimetha-namine (MX-DA) and 4, 4'-diaminodicyclohexylmethane (HMDA). The two chain extenders were applied to successfully achieve both high strength and high self-healing ability. The BDM-1.7 and BDH-1.7 elastomers had high comprehensive self-healing efficiency (100%, 95%) after heated treatment at 60 °C, and exhibited exceptional comprehensive mechanical performances in tensile strength (20.6 ± 1.3 MPa, 37.1 ± 1.7 MPa), toughness (83.5 ± 2.0 MJ/m3, 118.8 ± 5.1 MJ/m3), puncture resistance (196.0 mJ, 626.0 mJ), and adhesion (4.6 MPa, 4.8 MPa). The peculiar mechanical and self-healing properties of TPUs originated from the coexisting short and long hard segments, strain-induced crystallization (SIC). The two elastomers with excellent properties could be applied to engineering-grade fields such as commercial sealants, adhesives, and so on.

A Novel Strategy for Creating an Antibacterial Surface Using a Highly Efficient Electrospray-Based Method for Silica Deposition.

Adhesion of bacteria on biomedical implant surfaces is a prerequisite for biofilm formation, which may increase the chances of infection and chronic inflammation. In this study, we employed a novel electrospray-based technique to develop an antibacterial surface by efficiently depositing silica homogeneously onto polyethylene terephthalate (PET) film to achieve hydrophobic and anti-adhesive properties. We evaluated its potential application in inhibiting bacterial adhesion using both Gram-negative Escherichia coli (E. coli) and Gram-positive Staphylococcus aureus (S. aureus) bacteria. These silica-deposited PET surfaces could provide hydrophobic surfaces with a water contact angle greater than 120° as well as increased surface roughness (root mean square roughness value of 82.50 ± 16.22 nm and average roughness value of 65.15 ± 15.26 nm) that could significantly reduce bacterial adhesion by approximately 66.30% and 64.09% for E. coli and S. aureus, respectively, compared with those on plain PET surfaces. Furthermore, we observed that silica-deposited PET surfaces showed no detrimental effects on cell viability in human dermal fibroblasts, as confirmed by MTT (3-(4,5-dimethylthiazol-2-yl)-2,5 diphenyl tetrazolium bromide and live/dead assays. Taken together, such approaches that are easy to synthesize, cost effective, and efficient, and could provide innovative strategies for preventing bacterial adhesion on biomedical implant surfaces in the clinical setting.

Antimicrobial performance of two preoperative skin preparation solutions containing iodine and isopropyl alcohol.

BACKGROUND: Healthcare-associated infections (HAIs) are a persistent clinical challenge caused primarily by bacteria on the skin. Proper utilization of optimized antiseptic skin preparation solutions helps reduce the prevalence and impact of HAIs by decreasing patient skin microorganisms preoperatively. The purpose of this study was to evaluate the efficacy of 2 antimicrobial solutions containing iodine and isopropyl alcohol (IPA): Povidone iodine (PVP-I) with IPA (ie, PVP-I+IPA, PurPrep) and Iodine Povacrylex+IPA (DuraPrep). METHODS: The antimicrobial activity of the test solutions was evaluated in vitro by determinations of minimum inhibitory concentrations (MICs) and minimum bactericidal concentrations (MBCs) against 1105 diverse microbial isolates and a time-kill assay to evaluate efficacy against 120 strains of Gram-positive and Gram-negative bacteria and yeasts. Peel tests were performed between skin samples treated with test solutions and representative drape/dressing materials to determine effects of test solutions on the biomechanical adhesion properties. Finally, an Institutional Review Board (IRB)-approved, randomized, controlled, single-center, partially blinded in vivo study was performed to assess the immediate and persistent antimicrobial activity of the test solutions on the abdomen and groin. RESULTS: Both PVP-I+IPA and Iodine Povacrylex+IPA solutions demonstrated broad-spectrum antimicrobial activity with MIC and MBC at less than 1% of the full-strength concentration of each product against a wide variety of microorganisms. In the time-kill tests, both solutions were able to successfully reduce all microbial populations by 99.99% (ie, 4 log10) at the contact times of 30 seconds, 2 minutes and 10 minutes. The 2 solutions showed relatively similar adhesion results when tested with 3 representative operating room materials. Both PVP-I+IPA and Iodine Povacrylex+IPA met the expected Food and Drug Administration (FDA) efficacy requirements at 10 minutes and 6 hours post-treatment for both anatomic sites (ie, groin, and abdomen) in the clinical study, with no safety issues or adverse events. CONCLUSIONS: Analysis of the in vitro antimicrobial activity, biomechanical adhesive strength, and in vivo efficacy of PVP-I+IPA demonstrated similar results compared to Iodine Povacrylex+IPA. Both products were efficacious at reducing or eliminating a wide range of clinically-relevant microorganisms in lab-based and clinical settings, supporting their use as antiseptic skin preparation solutions to reduce bacteria on the skin that can cause infection.

Preparation and Evaluation of Rice Bran-Modified Urea Formaldehyde as Environmental Friendly Wood Adhesive.

In this study, defatted rice bran (RB) is used to prepare an environmentally friendly adhesive through chemical modifications. The RB is mixed with distilled water with ratios of 1:5 and 1:4 to prepare Type A and Type B adhesives, respectively having pH of 6, 8 and 10. Type A adhesive is prepared by treating RB with 1% potassium permanganate and 4% poly(vinyl alcohol), whereas Type B is formulated by adding 17.3% formaldehyde and 5.7% urea to RB. Viscosity, gel time, solid content, shear strength, Fourier transform infrared (FTIR) spectroscopy is carried out, and glass transition temperature (T g), and activation energy (E a) are determined to evaluate the performance of the adhesives. E a data reveal that adhesives prepared at mild alkaline (pH 8) form long-chain polymers. Gel time is higher in the fabricated adhesives than that of the commercial urea formaldehyde (UF). FTIR data suggest that functional groups of the raw RB are chemically modified, which enhances the bondability of the adhesives. Shear strength data indicates that bonding strength increases with increasing pH. Similar results are also observed for physical and mechanical properties of fabricated particleboards with the adhesives. The results demonstrate that RB-based adhesives can be used as a potential alternative to currently used UF-based resin.

Review on Development and Dental Applications of Polyetheretherketone-Based Biomaterials and Restorations.

Polyetheretherketone (PEEK) is an important high-performance thermoplastic. Its excellent strength, stiffness, toughness, fatigue resistance, biocompatibility, chemical stability and radiolucency have made PEEK attractive in dental and orthopedic applications. However, PEEK has an inherently hydrophobic and chemically inert surface, which has restricted its widespread use in clinical applications, especially in bonding with dental resin composites. Cutting edge research on novel methods to improve PEEK applications in dentistry, including oral implant, prosthodontics and orthodontics, is reviewed in this article. In addition, this article also discusses innovative surface modifications of PEEK, which are a focus area of active investigations. Furthermore, this article also discusses the necessary future studies and clinical trials for the use of PEEK in the human oral environment to investigate its feasibility and long-term performance.

Apparent Young's Modulus of the Adhesive in Numerical Modeling of Adhesive Joints.

This article is an evaluation of the phenomena occurring in adhesive joints during curing and their consequences. Considering changes in the values of Young's modulus distributed along the joint thickness, and potential changes in adhesive strength in the cured state, the use of a numerical model may make it possible to improve finite element simulation effects and bring their results closer to experimental data. The results of a tensile test of a double overlap adhesive joint sample, performed using an extensometer, are presented. This test allowed for the precise determination of the shear modulus G of the cured adhesive under experimental conditions. Then, on the basis of the research carried out so far, a numerical model was built, taking the differences observed in the properties of the joint material into account. The stress distribution in a three-zone adhesive joint was analyzed in comparison to the standard numerical model in which the adhesive in the joint was treated as isotropic. It is proposed that a joint model with three-zones, differing in the Young's modulus values, is more accurate for mapping the experimental results.

Evolution of Mechanical Stress (In-vitro) on Properties of Granulocytes in Acute Lymphoblastic Leukemia.

Acute lymphoid leukemia (ALL) affects the lymph cells or lymphocytes that make up the lymph tissue and prevents the proper maturation of the bone marrow cells. The processes through which cells convert mechanical stimuli into biochemical signals are called mechanical transitions and result in the sensation of specific cellular responses. In the present study, the functional properties of granulocytes of the patients with ALL were investigated using the in vitro mechanical stress model. The experimental part of the work was executed using blood from patients with ALL (n=30) being treated in the Hematological Department of Belgorod Region Hospital, Belgorod, Russia. The patients were in the age range of 18-45 years. Sample blood was obtained from all the patients who underwent a standard course of chemotherapy. Blood sampling was performed using a venepuncture and collected into the vacuum tubes Vacuette K3E. Blood samples from each experimental group were divided into two groups of control and experiment. The injection model of mechanical stress was used for the experiment group in vitro. Subsequently, the adenosine triphosphate (ATP) concentration increased by 1.8 times in this group, compared with the controls. Young's module, which numerically characterizes the rigidity of the granulocytes' plasmalemma, decreased by 54.4% (P<0.05) under the influence of mechanical stress. The surface potential of plasmalemma was not significantly different between samples in the group of control and experiment in patients with ALL. However, the adhesive force between erythrocyte and granulocyte increased by 30.7% (P<0.05). The osmotic load test showed an increase in the cell's volume during incubation. The use of membrane reserve by granulocytes increased by 47% (P<0.05) at the initial seconds of incubation. The obtained results pointed to the regulatory role of ATP molecules in intercellular signaling and add to the present literature regarding the mechanisms of intercellular interaction in the microvasculature on the development of leukemia. Moreover, the obtained results can be taken into account for the development of new pharmacological immune correctors.