Controllable preparation of carbon coating Ge nanospheres with a cubic hollow structure for high-performance lithium ion batteries.

Germanium based nanomaterials are very promising as the anodes for the lithium ion batteries since their large specific capacity, excellent lithium diffusivity and high conductivity. However, their controllable preparation is still very difficult to achieve. Herein, we facilely prepare a unique carbon coating Ge nanospheres with a cubic hollow structure (Ge@C) via a hydrothermal synthesis and subsequent pyrolysis using low-cost GeO2 as precursors. The hollow Ge@C nanostructure not only provides abundant interior space to alleviate the huge volumetric expansion of Ge upon lithiation, but also facilitates the transmission of lithium ions and electrons. Moreover, experiment analyses and density functional theory (DFT) calculations unveil the excellent lithium adsorption ability, high exchange current density, low activation energy for lithium diffusion of the hollow Ge@C electrode, thus exhibiting significant lithium storage advantages with a large charge capacity (1483 mAh/g under 200 mA g-1), distinguished rate ability (710 mAh/g under 8000 mA g-1) as well as long-term cycling stability (1130 mAh/g after 900 cycles under 1000 mA g-1). Therefore, this work offers new paths for controllable synthesis and fabrication of high-performance Ge based lithium storage nanomaterials.

Customizing Pore Structure and Lithiophilic Sites Dual-Gradient Free-Standing 3D Lithium-Based Anode to Enable Excellent Lithium Metal Batteries.

Developing 3D hosts is one of the most promising strategies for putting forward the practical application of lithium(Li)-based anodes. However, the concentration polarization and uniform electric field of the traditional 3D hosts result in undesirable "top growth" of Li, reduced space utilization, and obnoxious dendrites. Herein, a novel dual-gradient 3D host (GDPL-3DH) simultaneously possessing gradient-distributed pore structure and lithiophilic sites is constructed by an electrospinning route. Under the synergistic effect of the gradient-distributed pore and lithiophilic sites, the GDPL-3DH exhibits the gradient-increased electrical conductivity from top to bottom. Also, Li is preferentially and uniformly deposited at the bottom of the GDPL-3DH with a typical "bottom-top" mode confirmed by the optical and SEM images, without Li dendrites. Consequently, an ultra-long lifespan of 5250 h of a symmetrical cell at 2 mA cm-2 with a fixed capacity of 2 mAh cm-2 is achieved. Also, the full cells based on the LiFePO4, S/C, and LiNi0.8Co0.1Mn0.1O2 cathodes all exhibit excellent performances. Specifically, the LiFePO4-based cell maintains a high capacity of 136.8 mAh g-1 after 700 cycles at 1 C (1 C = 170 mA g-1) with 94.7% capacity retention. The novel dual-gradient strategy broadens the perspective of regulating the mechanism of lithium deposition.

Mechanism-guided Rational Design of Anode Coatings for Aqueous Zinc Ion Batteries.

Aqueous zinc ion batteries (ZIBs) hold promises as a safer, more cost-effective, and environmental-friendly alternative to lithium-ion batteries, especially for stationary energy storage. Recent advancements in protective anode coatings, which fine-tune zinc ion solvation structure, have yielded significant improvements in the aqueous ZIB performance, addressing dendrite formation and side reactions, thereby prolonging cycle lifetime. Understanding the underlying mechanisms of these coatings as ions sieves is crucial for further optimization and achieving long-term stability, which is a key requirement for practical applications. This concept explores recent developments in ZIB anode coatings from the view of molecular mechanisms and points out future research directions.

Zinc Dicyanamide: A Potential High-Capacity Negative Electrode for Li-Ion Batteries.

We demonstrate that the ß-polymorph of zinc dicyanamide, Zn[N(CN)2]2, can be efficiently used as a negative electrode material for lithium-ion batteries. Zn[N(CN)2]2 exhibits an unconventional increased capacity upon cycling with a maximum capacity of about 650 mAh·g-1 after 250 cycles at 0.5C, an increase of almost 250%, and then maintaining a large reversible capacity of more than 600 mAh·g-1 for 150 cycles. Such an increased capacity is primarily attributed to the increased level of activity in the conversion reaction. A combination of conversion-type and alloy-type mechanisms is revealed in this anode material via advanced characterization studies and theoretical calculations. This mechanism, observed here for the first time in transition-metal dicyanamides, is probably responsible for the outstanding electrochemical performance. We believe that this study guides the development of new high-capacity anode materials.

Benchmarking the Match of Porous Carbon Substrate Pore Volume on Silicon Anode Materials for Lithium-Ion Batteries.

Silicon (Si) is one of the most promising anode materials for high-energy-density lithium-ion batteries. However, the huge volume expansion hinders its commercial application. Embedding amorphous Si nanoparticles in a porous carbon framework is an effective way to alleviate Si volume expansion, with the pore volume of the carbon substrates playing a pivotal role. This work demonstrates the impact of pore volume on the electrochemical performance of the silicon/carbon porous composites from two perspectives: 1) pore volume affects the loadings of Si particles; 2) pore volume affects the structural stability and mechanical properties. The smaller pore volume of the carbon substrate cannot support the high Si loadings, which results in forming a thick Si shell on the surface, thereby being detrimental to cycling stability and the diffusion of electrons and ions. On top of that, the carbon substrate with a larger pore volume has poor structural stability due to its fragility, which is also not conducive to realizing long cycle life and high rate performance. Achieving excellent electrochemical performances should match the proper pore volume with Si content. This study will provide important insights into the rational design of the silicon/carbon porous composites based on the pore volume of the carbon substrates.

Sodiophilic Substrate Induces NaF-Rich Solid Electrolyte Interface for Dendrite-Free Sodium Metal Anode.

3D substrate with abundant sodiophilic active sites holds promise for implementing dendrite-free sodium metal anodes and high-performance sodium batteries. However, the heightened electrode/electrolyte side reactions stemming from high specific surface area still hinder electrode structure stability and cycling reversibility, particularly under high current densities. Herein, the solid electrolyte interface (SEI) component is regulated and detrimental side reactions are restrained through the uniform loading of Na-Sn alloy onto a porous 3D nanofiber framework (NaSn-PCNF). The strong interaction between Na-Sn alloy and PF6 - anions facilitates the dissociation of sodium salts and releases more free sodium ions for effective charge transfer. Simultaneously, the modulations of the interfacial electrolyte solvation structure and the construction of a high NaF content SEI layer stabilize the electrode/electrolyte interface. NaSn-PCNF symmetrical battery demonstrates stable cycling for over 600 h with an ultralow overpotential of 24.5 mV under harsh condition of 10 mA cm-2 and 10 mAh cm-2. Moreover, the full cells and pouch cells exhibit accelerated reaction kinetics and splendid capacity retention, providing valuable insights into the development of advanced Na substrates for high-energy sodium metal batteries.

Gel Polymer Electrolyte Enables Low-Temperature and High-Rate Lithium-Ion Batteries via Bionic Interface Design.

Traditional ethylene carbonate (EC)-based electrolytes constrain the applications of silicon carbon (Si-C) anodes under fast-charging and low-temperature conditions due to sluggish Li+ migration kinetics and unstable solid electrolyte interphase (SEI). Herein, inspired by the efficient water purification and soil stabilization of aquatic plants, a stable SEI with a 3D desolvation interface is designed with gel polymer electrolyte (GPE), accelerating Li+ desolvation and migration at the interface and within stable SEI. As demonstrated by theoretical simulations and experiment results, the resulting poly(1,3-dioxolane) (PDOL), prepared by in situ ring-opening polymerization of 1,3-dioxolane (DOL), creates a 3D desolvation area, improving the Li+ desolvation at the interface and yielding an amorphous GPE with a high Li+ ionic conductivity (5.73 mS cm-1). Furthermore, more anions participate in the solvated structure, forming an anion-derived stable SEI and improving Li+ transport through SEI. Consequently, the Si-C anode achieves excellent rate performance with GPE at room temperature (RT) and low temperature (-40 °C). The pouch full cell coupled with LiFePO4 cathode obtains 97.42 mAh g-1 after 500 cycles at 5 C/5 C. This innovatively designed 3D desolvation interface and SEI represent significant breakthroughs for developing fast-charging and low-temperature batteries.

Modulation of Electron Push-Pull by Redox Non-Innocent Additives for Long Cycle Life Zinc Anode.

Application of an aqueous Zn-ion battery is plagued by a water-induced hydrogen evolution reaction (HER), resulting in local pH variations and an unstable electrode-electrolyte interface (EEI) with uncontrolled Zn plating and side reactions. Here, 4-methyl pyridine N-oxide (PNO) is introduced as a redox non-innocent additive that comprises a hydrophilic bipolar N+-O- ion pair as a coordinating ligand for Zn and a hydrophobic ─CH3 group at the para position of the pyridine ring that reduces water activity at the EEI, thereby enhancing stability. The N+-O- moiety of PNO possesses the unique functionality of an efficient push electron donor and pull electron acceptor, thus maintaining the desired pH during charging/discharging. Intriguingly, replacing ─CH3 (electron pushing +I effect) by ─CF3 group (electron pulling ─I effect), however, does not improve the reversibility; instead, it degrades the cell performance. The electrolyte with 2 m ZnSO4 + 15 mm PNO enables symmetric cell Zn plating/stripping for a remarkable > 10 000 h at 0.5 mA cm-2 and exhibits coulombic efficiency (CE) ≈99.61% at 0.8 mA cm-2 in Zn/Cu asymmetric cell. This work showcases the immense interplay of the electron push-pull of the additives on the cycling.

Supramolecular Metal-Organic Framework for the High Stability of Aqueous Rechargeable Zinc Batteries.

Aqueous rechargeable Zn batteries (AZBs) are considered to be promising next-generation battery systems. However, the growth of Zn dendrites and water-induced side reactions have hindered their practical application, especially with regard to long-term cyclability. To address these challenges, we introduce a supramolecular metal-organic framework (SMOF) coating layer using an α-cyclodextrin-based MOF (α-CD-MOF-K) and a polymeric binder. The plate-like α-CD-MOF-K particles, combined with the polymeric binder create dense and homogeneous Zn2+ ion conductive pore channels that can vertically transport Zn2+ ions through the cavity while restricting the contact of water molecules. Molecular dynamics (MD) simulation verifies that Zn2+ ions can reversibly migrate through the pores of α-CD-MOF-K by partial dehydration. The uniform Zn deposition/dissolution promotes a smooth solid-electrolyte interface layer on the Zn metal anode and effectively suppresses side reactions with free water molecules. The α-CD-MOF-K@Zn symmetric cell exhibits stable cycling and a small polarization voltage of 70 mV for 800 h at 5 mA cm-2, and the α-CD-MOF-K@Zn|α-MnO2 full cell shows only 0.12% capacity decay per cycle at a rate of 1 A g-1.

Interfacial Coupling toward Bismuth Sulfide/MXene Heterostructures Empowering Reversible Magnesium Storage.

Bismuth-based compounds based on conversion-alloying reactions of multielectron transfer have attracted extensive attention as alternative anode candidates for rechargeable magnesium batteries (rMBs). However, the inadequate magnesium storage capability induced by the sluggish kinetics, poor reversibility, and terrible structural stability impedes their practical utilization. Herein, monodispersed Bi2S3 anchored on MXene has been prepared via a simple self-assembly strategy to induce the interfacial bonding of Ti-S and Ti-O-Bi. Unique superiority, including good electrical conductivity, high mechanical strength, and rapid charge transfer, is cleverly integrated together in the Bi2S3/MXene heterostructures, which endowed heterostructures with enhanced magnesium storage performance. Density functional theory calculations combined with kinetic behavior analyses confirm the favorable charge transfer and low ion diffusion barrier in hybrids. Furthermore, a stepwise insertion-conversion-alloying reaction mechanism is revealed in depth by ex situ investigations, which may also account for promoting performance. This work provides significant inspirations for constructing ingenious multicompositional hybrids by strong interfacial coupling engineering toward high-performance energy storage devices.

Carbon Nanotubes Connecting and Encapsulating MoS2-Doped SnO2 Nanoparticles as an Excellent Lithium Storage Performance Anode Material.

Doping and carbon encapsulation modifications have been proven to be effective methods for enhancing the lithium storage performance of batteries. The hydrothermal method and ball milling are commonly used methods for material synthesis. In this study, a composite anode material rich in carbon nanotubes (CNTs) conductive tubular network connection and encapsulation of SnO2-MoS2@CNTs (SMC) was synthesized by combining these two methods. In this highly conductive network, nano-SnO2 particles are uniformly dispersed and embedded in MoS2 with a layered structure, and the obtained SnO2-MoS2 composite material is tightly connected and encapsulated by the tubular network of CNTs. It is worth noting that the incorporation of layered MoS2 not only effectively anchors the SnO2 nanoparticles, but also provides a broader space for lithium-ion movement due to the larger interlayer spacing. The conductive network of CNTs shortens the diffusion path of electrons and Li+ and provides more diffusion channels. The reversible capacity of the SnO2-MoS2@CNTs nanocomposite material remains at 1069.3 mA h g-1 after 320 cycles at 0.2 A g-1, and it exhibits excellent long-term cycling stability, maintaining 904.5 mA h g-1 after 1000 cycles at 1.0 A g-1. The composite material demonstrates excellent pseudocapacitive contribution rate performance, with a contribution rate of 87% at 2.0 mV s-1. The results indicate that SnO2-MoS2@CNTs has excellent electrochemical lithium storage performance and is a promising anode material for lithium-ion batteries.

Boosting bioelectricity generation in bioelectrochemical systems with nitrogen-doped three-dimensional graphene aerogel anode.

Bioelectricity generation by electrochemically active bacteria has become particularly appealing due to its vast potential in energy production, pollution treatment, and biosynthesis. However, developing high-performance anodes for bioelectricity generation remains a significant challenge. In this study, a highly efficient three-dimensional nitrogen-doped macroporous graphene aerogel anode with a nitrogen content of approximately 4.38 ± 0.50 at% was fabricated using hydrothermal method. The anode was successfully implemented in bioelectrochemical systems inoculated with Shewanella oneidensis MR-1, resulting in a significantly higher anodic current density (1.0 A/m2) compared to the control one. This enhancement was attributed to the greater biocapacity and improved extracellular electron transfer efficiency of the anode. Additionally, the N-doped aerogel anode demonstrated excellent performance in mixed-culture inoculated bioelectrochemical systems, achieving a high power density of 4.2 ± 0.2 W/m², one of the highest reported for three-dimensional carbon-based bioelectrochemical systems to date. Such improvements are likely due to the good biocompatibility of the N-doped aerogel anode, increased extracellular electron transfer efficiency at the bacteria/anode interface, and selectively enrichment of electroactive Geobacter soli within the NGA anode. Furthermore, based on gene-level Picrust2 prediction results, N-doping significantly upregulated the conductive pili-related genes of Geobacter in the three-dimensional anode, increasing the physical connection channels of bacteria, and thus strengthening the extracellular electron transfer process in Geobacter.

3D Leaf-Like Copper-Zinc Alloy Enables Dendrite-Free Zinc Anode for Ultra-Long Life Aqueous Zinc Batteries.

Metallic zinc exhibits immense potential as an anode material for aqueous rechargeable zinc batteries due to its high theoretical capacity, low redox potential, and inherent safety. However, practical applications are hindered by dendrite formation and poor cycling stability. Herein, a facile substitution reaction method is presented to fabricate a 3D leaf-like Cu@Zn composite anode. This unique architecture, featuring a 3D network of leaf-like Cu on a Zn foil surface, significantly reduces nucleation overpotential and facilitates uniform Zn plating/stripping, effectively suppressing dendrite growth. Notably, an alloy layer of CuZn5 forms in situ on the 3D Cu layer during cycling. DFT calculations reveal that this CuZn5 alloy possesses a lower Zn binding energy compared to both Cu and Zn metal, further promoting Zn plating/stripping and enhancing electrochemical kinetics. Consequently, the symmetric Cu@Zn electrode exhibits remarkable cycling stability, surpassing 1300 h at 0.5 mA cm-2 with negligible dendrite formation. Furthermore, full cells comprising Cu@Zn||VO2 exhibit superior capacity and rate performance compared to bare Zn anodes. This work provides a promising strategy for constructing highly stable and efficient Zn anodes for next-generation aqueous zinc batteries.

Selection of Negative Charged Acidic Polar Additives to Regulate Electric Double Layer for Stable Zinc Ion Battery.

Zinc-ion batteries are promising for large-scale electrochemical energy storage systems, which still suffer from interfacial issues, e.g., hydrogen evolution side reaction (HER), self-corrosion, and uncontrollable dendritic Zn electrodeposition. Although the regulation of electric double layer (EDL) has been verified for interfacial issues, the principle to select the additive as the regulator is still misted. Here, several typical amino acids with different characteristics were examined to reveal the interfacial behaviors in regulated EDL on the Zn anode. Negative charged acidic polarity (NCAP) has been unveiled as the guideline for selecting additive to reconstruct EDL with an inner zincophilic H2O-poor layer and to replace H2O molecules of hydrated Zn2+ with NCAP glutamate. Taking the synergistic effects of EDL regulation, the uncontrollable interface is significantly stabilized from the suppressed HER and anti-self-corrosion with uniform electrodeposition. Consequently, by adding NCAP glutamate, a high average Coulombic efficiency of 99.83% of Zn metal is achieved in Zn|Cu asymmetrical cell for over 2000 cycles, and NH4V4O10|Zn full cell exhibits a high-capacity retention of 82.1% after 3000 cycles at 2 A g-1. Recapitulating, the NCAP principle posted here can quicken the design of trailblazing electrolyte additives for aqueous Zn-based electrochemical energy storage systems.

Integrated Interfacial Modulation Strategy: Trace Sodium Hydroxyethyl Sulfonate Additive for Extended-Life Zn Anode Based on Anion Adsorption and Electrostatic Shield.

Aqueous zinc-ion batteries (AZIBs) are poised to play a pivotal part in meeting the growing demands for energy storage and powering portable electronics for their superior security, affordability, and environmentally friendly characteristics. However, the detrimental side reactions occurring at the zinc anode and the dendrite caused by uneven zinc plating/stripping have greatly compromised the cycling life of AZIBs, thereby impeding their practical prospects. In this study, the interfacial comodulation strategy was employed by combining the "electrostatic shielding" effect of cations with the characteristic adsorption of anions. Two molar ZnSO4 served as the matrix, and sodium hydroxyethyl sulfonate (SHES) was selected as a low-cost, nontoxic additive. Experimental results confirm that SHES and zinc anode exhibit robust interactions that lead to the formation of an electrostatic shield and a dynamic adsorption layer at the interface, thereby suppressing hydrogen evolution and corrosion. The combined "electrostatic shielding" effect of sodium ions and the robust characteristic adsorption of hydroxyethyl sulfonate anions serve to guide the directed three-dimensional (3D) diffusion of Zn2+, facilitating rapid, stable, and uniform deposition of zinc. Due to these effects, incorporating 0.2 M SHES as an additive extends the cycle life beyond 3600 h and enables a highly reversible process of deposition and stripping in symmetric cells. Additionally, the Zn-Cu half-cell exhibits reliable cycling for over 1400 cycles, achieving an average Coulombic efficiency of 99.6%. Moreover, the introduction of this additive substantially enhances the performance of Zn-MnO2 and Zn-NH4V4O10 full cells. This study demonstrates the practical feasibility of achieving anodes with high reversibility in AZIBs through the implementation of a strategy that involves anion adsorption at the interface, which holds paramount significance for the practical application of AZIBs.

Highly Reversible and Dendrite-Free Zinc Anodes Enabled by PEDOT Nanowire Interfacial Layers for Aqueous Zinc-Ion Batteries.

The aqueous zinc-ion batteries (ZIBs) have gained increasing attention because of their high specific capacity, low cost, and good safety. However, side reactions, hydrogen evolution reaction, and uncontrolled zinc dendrites accompanying the Zn metal anodes have impeded the applications of ZIBs in grid-scale energy storage. Herein, the poly(3,4-ethylenedioxythiophene) (PEDOT) nanowires as an interfacial layer on the Zn anode (Zn-PEDOT) are reported to address the above issues. Our experimental results and density functional theory simulation reveal that the interactions between the Zn2+ and S atoms in thiophene rings of PEDOT not only facilitate the desolvation of hydrated Zn2+ but also can regulate the diffusion of Zn2+ along the thiophene molecular chains and induce the dendrite-free deposition of Zn along the (002) surface. Consequently, the Zn||Cu-PEDOT half-cell exhibits highly reversible plating/stripping behavior with an average Coulombic efficiency of 99.7% over 2500 cycles at 1 mA cm-2 and a capacity of 0.5 mAh cm-2. A symmetric Zn-PEDOT cell can steadily operate over 1100 h at 1 mA cm-2 (1 mAh cm-2) and 470 h at 10 mA cm-2 (2 mAh cm-2), outperforming the counterpart bare Zn anodes. Besides, a Zn-PEDOT||V2O5 full cell could deliver a specific capacity of 280 mAh g-1 at 1 A g-1 and exhibits a decent cycling stability, which are much superior to the bare Zn||V2O5 cell. Our results demonstrate that PEDOT nanowires are one of the promising interfacial layers for dendrite-free aqueous ZIBs.

Self-Propagating Fabrication of a 3D Graphite@rGO Film Anode for High-performance Potassium-Ion Batteries.

Graphite, with abundant resources and low cost, is regarded as a promising anode material for potassium-ion batteries (PIBs). However, because of the large size of potassium ions, the intercalation/deintercalation of potassium between the interlayers of graphite results in its huge volume expansion, leading to poor cycling stability and rate performance. Herein, a self-propagating reduction strategy is adopted to fabricate a flexible, self-supporting 3D porous graphite@reduced graphene oxide (3D-G@rGO) composite film for PIBs. The 3D porous network can not only effectively mitigate the volume expansion in graphite but also provide numerous active sites for potassium storage as well as allow for electrolyte penetration and rapid ion migration. Therefore, compared to the pristine graphite anode, the flexible 3D-G@rGO film electrode exhibits greatly improved K-storage performance with a reversible capacity of 452.8 mAh g-1 at 0.1 C and a capacity retention rate of 80.4% after 100 cycles. It also presents excellent rate capability with a high specific capacity of 139.1 and 94.2 mAh g-1 maintained at 2 and 5 C, respectively. The proposed self-propagating reduction strategy to construct a three-dimensional self-supporting structure is a viable route to improve the structural stability and potassium storage performance of graphite anodes.

Batch-Scale Synthesis and Interfacially Enhanced Stability of Silicon Suboxide-Based Anodes toward High-Performance Lithium-Ion Batteries.

SiOx anode materials are among the most promising candidates for next-generation high-energy-density lithium-ion batteries (LIBs). However, their commercial application is hindered by poor conductivity, low initial Coulombic efficiency (ICE), and an unstable solid electrolyte interface. Developing cost-effective SiOx anodes with high electrochemical performance is crucial for advanced LIBs. To tackle these issues, this study utilized APTES as a silicon source and carbon nanotubes (CNTs) as additives to prepare a T-SiOx/C/CNTs composite material with N doping and in situ carbon coating using a "molecular assembly combined with controlled pyrolysis" strategy under mild conditions. The in situ carbon coating, formed by the pyrolysis of organic groups on the molecular precursor, effectively protects the inner SiOx active material. The introduced CNTs enhance electron migration and improve the rigidity of the carbon coating layer. The prelithiated T-SiOx@C/CNTs electrode achieves an ICE of 91.6%, with a specific capacity of 622 mAh g-1 after 400 cycles at 1 A g-1 and 475.8 mAh g-1 after 800 cycles. Full cell tests with commercial NCM811 cathodes further demonstrate the potential of T-SiOx@C/CNTs as a highly promising anode material. This work provides some insights into the rational design of advanced anode materials for LIBs, paving the way for their future development and application.

Unveiling the Reaction Mystery Between Lithium Polysulfides and Lithium Metal Anode in Lithium-Sulfur Batteries.

Lithium-sulfur (Li-S) batteries are widely regarded as one of the most promising next-generation high-energy-density energy storage devices. However, soluble lithium polysulfides (LiPSs) corrode Li metal and deteriorate the cycling stability of Li-S batteries. Understanding the reaction mechanism between LiPSs and Li metal anode is imperative. Herein, the reaction rate and products of LiPSs with Li metal anode, the composition and structure of the as-generated solid electrolyte interphase (SEI), and the mechanism of lithium nitrate (LiNO3) additives for inhibiting the corrosion reactions are systematically unveiled. Concretely, LiPSs react with Li metal anode more rapidly than Li salt and generate a Li2S-rich SEI. The Li2S-rich SEI is highly reactive with LiPSs, which exacerbates the formation of dendritic Li and the continuous corrosion of active Li. LiNO3 functions dominantly by modulating the solvation structure of LiPSs and inherently reducing the reactivity of LiPSs, rather than the conventional understanding of LiNO3 participating in the formation of SEI. This work reveals the reaction mechanism between LiPSs and Li metal anode and inspires rational regulating of the solvation structure of LiPSs for stabilizing Li metal anode in Li-S batteries.

Stabilization Strategies of Lithium Metal Anode Toward Dendrite-Free Lithium-Sulfur Batteries.

Lithium-sulfur (Li-S) batteries are considered as a most promising rechargeable lithium metal batteries because of their high energy density and low cost. However, the Li-S batteries mainly suffer the capacity decay issue caused by the shutting effect of lithium polysulfides and the safety issues arising from the Li dendrites formation. This review outlines the current issues of Li-S batteries. Furthermore, we comprehensively summarized the challenges encountered by Li anode in Li-S batteries, such as the heterogeneous deposition of the Li anode, the unstable solid electrolyte interface (SEI) layer, and volume expansion. Moreover, research progresses in the stabilization strategies of Li anodes (physical approaches, optimization of electrolyte, surface protection layer, and design of current collector) is discussed in detail. Lastly, the remaining challenges and future research directions of Li metal anode stabilization in Li-S batteries are also present.