Synthesis of Benzoic Acids from Electrochemically Reduced CO2 Using Heterogeneous Catalysts.

A method for the synthesis of benzoic acids from aryl iodides using two of the most abundant and sustainable feedstocks, carbon dioxide (CO2) and water, is disclosed. Central to this method is an effective and selective electrochemical reduction of CO2 to CO, which mitigates unwanted dehalogenation reactions occurring when H2 is produced via the hydrogen evolution reaction (HER). In a 3-compartment set-up, CO2 was reduced to CO electrochemically by using a surface-modified silver electrode in aqueous electrolyte. The ex-situ generated CO further underwent hydroxycarbonylation of aryl iodides by MOF-supported palladium catalyst in excellent yields at room temperature. The method avoids the direct handling of hazardous CO gas and gives a wide range of benzoic acid derivatives. Both components of the tandem system can be recycled for several consecutive runs while keeping a high catalytic activity.

Benchmarking Performance Indices of Electrochemical CO2 Reduction to Ethylene Based on Prospective Life Cycle Assessment for Negative Emissions.

To mitigate global warming to the most ambitious targets, it is necessary to remove CO2 from the atmosphere and reduce fossil fuels use. The electrochemical conversion of CO2 to ethylene (C2H4) as a basic chemical is a promising technology that meets both requirements; however, its life cycle CO2 emissions remain inconclusive because of varying assumptions in the performance indices. This study aimed to set benchmarks for the four most sensitive indices to achieve -0.5 t-CO2/t-C2H4 by calculating net greenhouse gas (GHG) emissions through a prospective life cycle assessment of a model system including CO2 capture, CO2 enrichment, electrochemical conversion, CO2 recycling, and cryogenic separation. As a result, the electrochemical conversion process was the hotspot of life cycle emissions, and representative benchmarks were determined as follows: cell voltage, 3.5 V; C2H4 Faraday efficiency, 70%; conversion rate, 20%; and electrochemical CO2 recycling energy, 2.2 GJ/t-CO2. The gaps between the benchmarks and current top data of cell voltage and Faraday efficiency were <10%, and suppressing the performance degradation for up to one year was found to be a critical requirement. These results can direct research towards the development of a year-round stable system, rather than further improving the performance indices.

Nature-inspired innovation: Alginic-kojic acid material for sustainable antibacterial and carbon dioxide fixation.

The current environmental consciousness of the world's population encourages researchers to work on new materials that are environmentally benign and able to display the appropriate features for the needed application. To develop high-performing, inexpensive eco-materials, scientists have frequently turned to nature, attempting to mimic its processes' excellent performance at a reasonable price. In this regard, we decided to focus on alginic acid (AA), a polysaccharide widely found in brown algae, and kojic acid (KA), a chelating agent fungi produces. This study proposes rapidly synthesizing a sustainable, biocompatible material (AK) based on AA and KA, employing chlorokojic acid (CKA). The material has a dual function: antibacterial activity on both Gram-positive and Gram-negative bacteria, without any cytotoxic action on human cells in vitro, and catalytic ability to convert CO2 into cyclic carbonates at atmospheric pressure, without solvents, with high yields, and without the use of metals. Furthermore, the material's insolubility in organic solvents allows it to be easily separated from the reaction product and reused for other catalytic cycles. Both applications have a key role in the medical and environmental fields, combating the outbreak of infections and providing an innovative methodology to fix the CO2 on specific substrates.

Intrinsically Conductive and Cu-Functionalized Polymer-Composite Membranes as Gas Diffusion Electrodes for CO2 Electroreduction.

We introduced a new class of gas diffusion electrodes (GDEs) with adjustable pore morphology. We fabricated intrinsically conductive polymer-composite membranes containing carbon filler, enabling a pore structure variation through film casting cum phase separation protocols. We further selectively functionalized specific pore regions of the membranes with Cu by a NaBH4-facilitated coating strategy. The as-obtained GDEs can facilitate the electrochemical CO2 reduction reaction (CO2RR) at Cu active sites that are presented inside a defined and electrically conductive pore system. When employing them as free-standing cathodes in a CO2 flow electrolyzer, we achieved >70% Faradaic efficiencies for CO2RR products at up to 200 mA/cm2. We further demonstrated that deposition of a dense Cu layer on top of the membrane leads to obstruction of the underlying pore openings, inhibiting an excessive wetting of the pore pathways that transport gaseous CO2. However, the presentation of Cu inside the pore system of our novel membrane electrodes increased the C2H4/CO selectivity by a factor of up to 3 compared to Cu presented in the dense layer on top of the membrane. Additionally, we found that gaseous CO2 could still access Cu in macropores after wetting with electrolyte, while CO2RR was completely suppressed in wetted nm-scale pores.

Imidazolium and Pyridinium-based Ionic Porous Organic Polymers: Advances in Transformative Solutions for Oxoanion Sequestration and Non-redox CO2 Fixation.

The rapid pace of industrialization has led to a multitude of detrimental environmental consequences, including water pollution and global warming. Consequently, there is an urgent need to devise appropriate materials to address these challenges. Ionic porous organic polymers (iPOPs) have emerged as promising materials for oxoanion sequestration and non-redox CO2 fixation. Notably, iPOPs offer hydrothermal stability, structural tunability, a charged framework, and readily available nucleophilic counteranions. This review explores the significance of pores and charged functionalities alongside design strategies outlined in existing literature, mainly focusing on the incorporation of pyridinium and imidazolium units into nitrogen-rich iPOPs for oxoanion sequestration and non-redox CO2 fixation. The present review also addresses the current challenges and future prospects, delineating the design and development of innovative iPOPs for water treatment and heterogeneous catalysis.

Methane Formation Induced via Face-to-Face Orientation of Cyclic Fe Porphyrin Dimer in Photocatalytic CO2 Reduction.

Iron porphyrins are known to provide CH4 as an eight-electron reduction product of CO2 in a photochemical reaction. However, there are still some aspects of the reaction mechanism that remain unclear. In this study, we synthesized iron porphyrin dimers and carried out the photochemical CO2 reduction reactions in N,N-dimethylacetamide (DMA) containing a photosensitizer in the presence of 1,3-dimethyl-2-phenyl-2,3-dihydro-1H-benzo[d]imidazole (BIH) as an electron donor. We found that, despite a low catalytic turnover number, CH4 was produced only when these porphyrins were facing each other. The close proximity of the cyclic dimers, distinguishing them from a linear Fe porphyrin dimer and monomers, induced multi-electron CO2 reduction, emphasizing the unique role of their structural arrangement in CH4 formation.

Amine Functionalization of Channels of Metal-Organic Frameworks for Effective Chemical Fixation of Carbon Dioxide: A Comparative Study with Three Newly Designed Porous Networks.

Catalytic transformation of CO2 into value-added chemical products can provide an appropriate solution for the raising environmental issues. To date, various metal-organic frameworks (MOFs) with transition metal ions have been explored for CO2 capture and conversion, but alkaline earth metal-based MOFs are comparatively less studied. Metal ions like Sr(II) having relatively large radius give rise to a high coordination number resulting in higher stability of the MOFs. Moreover, the introduction of N-rich functional group in organic linker like -NH2, -CONH- and triazole into MOF backbone enhance their CO2 capture and conversion efficiency. Herein, the effect of amine group on the catalytic efficiency of MOFs for CO2 cycloaddition with epoxides under solvent free and ambient conditions are presented. The di-carboxylates, such as 5-aminoisophthalate (AmIP) and 5-bromoisophthalate (BrIP) were utilized to synthesize Sr(II) based MOFs. The Zn(II) MOF was synthesized using tetra-carboxylate containing amide spacer (OAT) and 4-amino-4H-1,2,4-triazole (AMT). All three MOFs exhibited porous networks with guest available volume ranging from 15 to 58 %. The catalytic efficiency of the MOFs towards carbon dioxide fixation reaction was explored. The catalytic performances revealed that the presence of amine group in the channels enhances the catalytic efficiency of the MOFs.

The Tandem Nitrate and CO2 Reduction for Urea Electrosynthesis: Role of Surface N-Intermediates in CO2 Capture and Activation.

Electrochemical reduction of CO2 and nitrate offers a promising avenue to produce valuable chemicals through the using of greenhouse gas and nitrogen-containing wastewater. However, the generally proposed reaction pathway of concurrent CO2 and nitrate reduction for urea synthesis requires the catalysts to be both efficient in both CO2 and nitrate reduction, thus narrowing the selection range of suitable catalysts. Herein, we demonstrate a distinct mechanism in urea synthesis, a tandem NO3 - and CO2 reduction, in which the surface amino species generated by nitrate reduction play the role to capture free CO2 and subsequent initiate its activation. When using the TiO2 electrocatalyst derived from MIL-125-NH2, it intrinsically exhibits low activity in aqueous CO2 reduction, however, in the presence of both nitrate and CO2, this catalyst achieves an excellent urea yield rate of 43.37 mmol ⋅ g-1 ⋅ h-1 and a Faradaic efficiency of 48.88 % at -0.9 V vs. RHE in a flow cell. Even at a low CO2 level of 15 %, the Faradaic efficiency of urea synthesis remains robust at 42.33 %. The tandem reduction procedure was further confirmed by in situ spectroscopies and theoretical calculations. This research provides new insights into the selection and design of electrocatalysts for urea synthesis.

g-C3N4 as ballistic electron transport "Tunnel" in CsPbBr3-based ternary photocatalyst for gas phase CO2 reduction.

Perovskite CsPbBr3 quantum dot shows great potential in artificial photosynthesis, attributed to its outstanding optoelectronic properties. Nevertheless, its photocatalytic activity is hindered by insufficient catalytic active sites and severe charge recombination. In this work, a CsPbBr3@Ag-C3N4 ternary heterojunction photocatalyst is designed and synthesized for high-efficiency CO2 reduction. The CsPbBr3 quantum dots and Ag nanoparticles are chemically anchored on the surface of g-C3N4 sheets, forming an electron transfer tunnel from CsPbBr3 quantum dots to Ag nanoparticles via g-C3N4 sheets. The resulting CsPbBr3@Ag-C3N4 ternary photocatalyst, with spatial separation of photogenerated carriers, achieves a remarkable conversion rate of 19.49 µmol·g-1·h-1 with almost 100 % CO selectivity, a 3.13-fold enhancement in photocatalytic activity as compared to CsPbBr3 quantum dots. Density functional theory calculations reveal the rapid CO2 adsorption/activation and the decreased free energy (0.66 eV) of *COOH formation at the interface of Ag nanoparticles and g-C3N4 in contrast to the g-C3N4, leading to the excellent photocatalytic activity, while the thermodynamically favored CO desorption contributes to the high CO selectivity. This work presents an innovative strategy of constructing perovskite-based photocatalyst by modulating catalyst structure and offers profound insights for efficient CO2 conversion.

Corrigendum: Atypical carboxysome loci: JEEPs or junk?

[This corrects the article DOI: 10.3389/fmicb.2022.872708.].

Selective Recovery of Battery-Grade Li2CO3 from Spent NCM Cathode Materials Using a One-Step Method of CO2 Carbonation Recovery Without Acids or Bases.

The recovery of spent lithium-ion batteries by traditional acid leaching is limited by serious pollution, complicated technology, and the low purity of Li2CO3. To address the problems of the traditional acid leaching process and increasing demand for decarbonization, a technique for the selective carbonation leaching of Li and the recovery of battery-grade Li2CO3 by a simple concentration precipitation process without acids or bases was developed. The coupling of CO2 and reducing agents could effectively promote the precipitation of MCO3 (M=Ni/Co/Mn) and the selective leaching of Li by decreasing the reducing capability needed for transition metals and decreasing the pH of the solution. The optimal selective leaching process of Li was obtained under 1 MPa CO2 with 20 g/L Na2S2O3 at an L/S ratio of 30 mL/g for 1.5 h. FT-IR, XRD, ICP-MS and other methods were used to reveal the multiphase interfacial reaction mechanism of the carbonation reduction of layered cathode materials, which indicated that the reducing agent Na2S2O3 could promote lattice distortion of the cathode materials and effective separation of Li. In summary, a green and economical method for the selective recovery of battery-grade Li2CO3 using a one-step method of CO2 carbonation recovery in a near-neutral environment was proposed.

Pd-loaded hierarchical titanosilicalite-1 catalysts on CO2 cycloaddition with epoxides: Experimental and DFT investigations.

This work presents the synthesis of Pd-loaded microporous titanosilicalite-1 (Pd/TS-1) and Pd-loaded hierarchical titanosilicalite-1 (Pd/HTS-1) with abundant mesopores (2-30 nm) inside the framework via hydrothermal method using polydiallydimethyl ammonium chloride as the non-surfactant mesopore template. XRD, N2 sorption, FT-IR, FESEM-EDX, TEM, XPS, and DR-UV techniques were used to characterize the morphological and physicochemical properties of the synthesized materials. These materials were tested as heterogeneous catalysts, along with tetrapropylammonium bromide as co-catalyst, for cycloaddition reactions of CO2 with epoxides to produce cyclic carbonates. It was found that the epoxide conversions were influenced by acidity and pore accessibility of the catalysts. Using Pd/HTS-1 facilitated bulky substrates to access active sites, resulting in higher conversions than Pd/TS-1. Over 85 % conversions were achieved for at least five consecutive cycles without significant loss in catalytic activity. The interaction between the Pd active surfaces and epichlorohydrin (ECH) was further studied by DFT calculations. The existence of Pd(200) was more influential on adsorbing epichlorohydrin (ECH) and subsequent formation of dissociated ECH (DECH) intermediate than Pd(111) surface. However, Pd(111) was dominant in enhancing the activity of DECH species for capturing CO2. Therefore, the co-existence of Pd(200) and Pd(111) surfaces was needed for cycloaddition of CO2 with ECH.

Matched Redox Kinetics on Triazine-Based Carbon Nitride/Ni(OH)2 for Stoichiometric Overall Photocatalytic CO2 Conversion.

Mismatched reaction kinetics of CO2 reduction and H2O oxidation is the main obstacle limiting the overall photocatalytic CO2 conversion. Here, a molten salt strategy is used to construct tubular triazine-based carbon nitride (TCN) with more adsorption sites and stronger activation capability. Ni(OH)2 nanosheets are then grown over the TCN to trigger a proton-coupled electron transfer for a stoichiometric overall photocatalytic CO2 conversion via "3CO2 + 2H2O = CH4 + 2CO + 3O2." TCN reduces the energy barrier of H2O dissociation to promote H2O oxidation to O2 and supply sufficient protons to Ni(OH)2, whereby the CO2 conversion is accelerated due to the enhanced proton-coupled electron transfer process enabled by the sufficient proton supply from TCN. This work highlights the importance of matching the reaction kinetics of CO2 reduction and H2O oxidation by proton-coupled electron transfer on stoichiometric overall photocatalytic CO2 conversion.

Transcriptome analysis of the effects of different carbon dioxide concentrations on paramylon accumulation in Euglena gracilis Z.

Appropriate concentration of carbon dioxide (CO2) will promote algae growth and metabolism. Building upon this finding, the present study investigated the impact of different CO2 concentrations (5% and 20%) on the carbon sequestration capacity of E. gracilis through aeration culturing, employing a combination of physiological analyses and transcriptome analysis. The results demonstrated that under 5% CO2 concentration, the cell density of E. gracilis was 1.79 times higher than that achieved in an air culture condition, and the paramylon content of E. gracilis was found to be 6.18 times higher than that of the air group. Based on transcriptome analysis, the carbon metabolism of E. gracilis was discussed. Significant up-regulation expression of genes associated with carbon synthesis was validated by an increase in paramylon content. This study revealed that under 5% CO2 conditions, E. gracilis exhibited elevated growth rate and enhanced photosynthetic carbon assimilation efficiency.

NADH-dependent formate dehydrogenase mutants for efficient carbon dioxide fixation.

Bioconversion of CO2 to high-valuable products is a globally pursued sustainable technology for carbon neutrality. However, low CO2 activation with formate dehydrogenase (FDH) remains a major challenge for further upcycling due to the poor CO2 affinity, reduction activity and stability of currently used FDHs. Here, we present two recombined mutants, ΔFDHPa48 and ΔFDHPa4814, which exhibit high CO2 reduction activity and antioxidative activity. Compared to FDHPa, the reduction activity of ΔFDHPa48 was increased up to 743 % and the yield in the reduction of CO2 to methanol was increased by 3.16-fold. Molecular dynamics identified that increasing the width of the substrate pocket of ΔFDHPa48 could improve the enzyme reduction activity. Meanwhile, the enhanced rigidity of C-terminal residues effectively protected the active center. These results fundamentally advanced our understanding of the CO2 activation process and efficient FDH for enzymatic CO2 activation and conversion.

Photoelectrocatalytic Utilization of CO2 : A Big Show of Si-based Photoelectrodes.

CO2 is a greenhouse gas that contributes to environmental deterioration; however, it can also be utilized as an abundant C1 resource for the production of valuable chemicals. Solar-driven photoelectrocatalytic (PEC) CO2 utilization represents an advanced technology for the resourcing of CO2 . The key to achieving PEC CO2 utilization lies in high-performance semiconductor photoelectrodes. Si-based photoelectrodes have attracted increasing attention in the field of PEC CO2 utilization due to their suitable band gap (1.1 eV), high carrier mobility, low cost, and abundance on Earth. There are two pathways to PEC CO2 utilization using Si-based photoelectrodes: direct reduction of CO2 into small molecule fuels and chemicals, and fixation of CO2 with organic substrates to generate high-value chemicals. The efficiency and product selectivity of PEC CO2 utilization depends on the structures of the photoelectrodes as well as the composition, morphology, and size of the catalysts. In recent years, significant and influential progress has been made in utilizing Si-based photoelectrodes for PEC CO2 utilization. This review summarizes the latest research achievements in Si-based PEC CO2 utilization, with a particular emphasis on the mechanistic understanding of CO2 reduction and fixation, which will inspire future developments in this field.

The Moon-Forming Impact and the Autotrophic Origin of Life.

The Moon-forming impact vaporized part of Earth's mantle, and turned the rest into a magma ocean, from which carbon dioxide degassed into the atmosphere, where it stayed until water rained out to form the oceans. The rain dissolved CO2 and made it available to react with transition metal catalysts in the Earth's crust so as to ultimately generate the organic compounds that form the backbone of microbial metabolism. The Moon-forming impact was key in building a planet with the capacity to generate life in that it converted carbon on Earth into a homogeneous and accessible substrate for organic synthesis. Today all ecosystems, without exception, depend upon primary producers, organisms that fix CO2 . According to theories of autotrophic origin, it has always been that way, because autotrophic theories posit that the first forms of life generated all the molecules needed to build a cell from CO2 , forging a direct line of continuity between Earth's initial CO2 -rich atmosphere and the first microorganisms. By modern accounts these were chemolithoautotrophic archaea and bacteria that initially colonized the crust and still inhabit that environment today.

Comprehensive understanding of the regulatory mechanism by which selenium nanoparticles boost CO2 fixation and cadmium tolerance in lipid-producing green algae under recycled medium.

Recycled medium plus cadmium is a promising technique for reducing the cultivation cost and enhancing the yield of microalgae lipids. However, oxidative stress and cadmium toxicity significantly hinder the resulting photosynthetic efficiency, cell growth and cell activity. Herein, selenium nanoparticles (SeNPs) were used to increase the total biomass, biolipid productivity, and tolerance to cadmium. Wide-ranging analyses of photosynthesis, energy yield, fatty acid profiles, cellular ultrastructure, and oxidative stress biomarkers were conducted to examine the function of SeNPs in CO2 fixation and cadmium resistance in Ankistrodesmus sp. EHY. The application of 15 µM cadmium and 2 mg L-1 SeNPs further enhanced the algal biomass productivity and lipid productivity to 500.64 mg L-1 d-1 and 301.14 mg L-1 d-1, respectively. Moreover, the rates of CO2 fixation, chlorophyll synthesis and total nitrogen removal were similarly increased by the application of SeNPs. Exogenous SeNPs strengthened cell growth and cadmium tolerance by upregulating photosynthesis, the TCA cycle and the antioxidant system, reducing the uptake and translocation of cadmium, and decreasing the levels of reactive oxidative stress (ROS), extracellular polymeric substances (EPSs) and cellular Cd2+ level in EHY under recycled medium and cadmium stress conditions. Additionally, a maximum energy yield of 127.40 KJ L-1 and a lipid content of 60.15% were achieved in the presence of both SeNPs and cadmium stress. This study may inspire the efficient disposal of recycled medium and biolipid production while also filling the knowledge gaps regarding the mechanisms of SeNP functions in carbon fixation and cadmium tolerance in microalgae.

Oxygen evolution from extremophilic cyanobacteria confined in hard biocoatings.

Biocoatings, in which viable bacteria are immobilized within a waterborne polymer coating for a wide range of potential applications, have garnered greater interest in recent years. In bioreactors, biocoatings can be ready-to-use alternatives for carbon capture or biofuel production that could be reused multiple times. Here, we have immobilized cyanobacteria in mechanically hard biocoatings, which were deposited from polymer colloids in water (i.e., latex). The biocoatings are formed upon heating to 37°C and fully dried before rehydrating. The viability and oxygen evolution of three cyanobacterial species within the biocoatings were compared. Synechococcus sp. PCC 7002 was non-viable inside the biocoatings immediately after drying, whereas Synechocystis sp. PCC 6803 survived the coating formation, as shown by an adenosine triphosphate (ATP) assay. Synechocystis sp. PCC 6803 consumed oxygen (by cell respiration) for up to 5 days, but was unable to perform photosynthesis, as indicated by a lack of oxygen evolution. However, Chroococcidiopsis cubana PCC 7433, a strain of desiccation-resistant extremophilic cyanobacteria, survived and performed photosynthesis and carbon capture within the biocoating, with specific rates of oxygen evolution up to 0.4 g of oxygen/g of biomass per day. Continuous measurements of dissolved oxygen were carried out over a month and showed no sign of decreasing activity. Extremophilic cyanobacteria are viable in a variety of environments, making them ideal candidates for use in biocoatings and other biotechnology. IMPORTANCE As water has become a precious resource, there is a growing need for less water-intensive use of microorganisms, while avoiding desiccation stress. Mechanically robust, ready-to-use biocoatings or "living paints" (a type of artificial biofilm consisting of a synthetic matrix containing functional bacteria) represent a novel way to address these issues. Here, we describe the revolutionary, first-ever use of an extremophilic cyanobacterium (Chroococcidiopsis cubana PCC 7433) in biocoatings, which were able to produce high levels of oxygen and carbon capture for at least 1 month despite complete desiccation and subsequent rehydration. Beyond culturing viable bacteria with reduced water resources, this pioneering use of extremophiles in biocoatings could be further developed for a variety of applications, including carbon capture, wastewater treatment and biofuel production.

Comparative Study between 2-Furonitrile and 2-Cyanopyridine as Dehydrants in Direct Synthesis of Dialkyl Carbonates from CO2 and Alcohols over Cerium Oxide Catalyst.

The shift of equilibrium by removing water with nitrile dehydrants is crucial for CeO2 -catalyzed synthesis of dialkyl carbonates from CO2 and alcohols. Two nitriles - 2-cyanopyridine and 2-furonitrile - were previously found as effective dehydrants, yet their detailed comparison as well as exploration of potential of 2-furonitrile remain insufficient. Herein, the performance of 2-cyanopyridine and 2-furonitrile was compared in the synthesis of various dialkyl carbonates. 2-furonitrile was found to be superior to 2-cyanopyridine in the synthesis of dialkyl carbonates from CO2 and bulky or long-chain (≥C3) alcohols. Namely, the yield of diisopropyl carbonate (up to 50 %) achieved using CeO2 and 2-furonitrile is comparable to or even higher than previously reported ones. Meanwhile, 2-cyanopyridine acted as a better dehydrant than 2-furonitrile in the synthesis of dimethyl carbonate and diethyl carbonate. The adsorption experiments and density functional theory calculations have indicated that the better performance of 2-furonitrile compared to 2-cyanopyridine in the synthesis of dialkyl carbonates from bulky or long-chain alcohols is due to the weaker interaction of 2-furonitrile with the CeO2 surface. Such weak interaction of 2-furonitrile offers a larger reaction field on the catalyst surface for both CO2 and alcohols.