Restauração em resina composta semidireta em dente posterior: relato de caso / Semi-direct composite restoration in posterior toth: a case report

A escolha da técnica restauradora desempenha papel fundamental na eficácia e duração de um tratamento reabilitador. O objetivo deste relato de caso foi descrever a utilização da técnica semidireta para a confecção de uma restauração em resina composta em um primeiro molar inferior. A paciente apresentava uma restauração insatisfatória no dente 36, que necessitava ser substituída devido à infiltração por cárie. Optou-se pela técnica semidireta devido à amplitude da cavidade, que envolvia estruturas de suporte, e pela combinação das vantagens das abordagens direta e indireta. O procedimento envolveu a remoção de tecido cariado, a aplicação de hidróxido de cálcio pasta, seguida da aplicação de uma fina camada de ionômero de vidro e, posteriormente, resina fluída para realizar o selamento dentinário. O preparo foi realizado seguindo os princípios necessários. O elemento em questão foi moldado com silicone de adição e o arco antagonista, com alginato. Ambos modelos foram vertidos com silicone para modelos semirrígidos e montados em oclusor de peças de brinquedo. A restauração semidireta foi confeccionada em resina composta Filtek Z350 XT, respeitando a anatomia do dente 36. Pigmentos foram utilizados para aprimorar detalhes estéticos. Após acabamento e polimento, a peça foi condicionada e cimentada com cimento dual Relyx Ultimate. Pode-se concluir que a abordagem restauradora por meio da técnica semidireta construída em modelo semirrígido é uma opção terapêutica conservadora e vantajosa para dentes com extensa destruição coronária. Essa técnica possibilita a restauração de forma eficaz, garantindo tanto a estética quanto a função adequada do dente afetado(AU)

The choice of restorative technique plays a fundamental role in the effectiveness and duration of rehabilitation treatment. The objective of this case report was to describe the use of the semi-direct technique to create a composite resin restoration in a lower first molar. The patient had an unsatisfactory restoration on tooth 36, which needed to be replaced due to cavity infiltration. The semi-direct technique was chosen due to the amplitude of the cavity, which involved support structures, and the combination of advantages of the direct and indirect approaches. The procedure involved the removal of carious tissue, and the application of calcium hydroxide paste, followed by the application of a thin layer of glass ionomer and, subsequently, fluid resin to seal the dentin. The preparation was carried out following the necessary principles. The element in question was molded with addition silicone and the antagonist arch was molded with alginate. Both models were poured with silicone for semi-rigid models and mounted on toy parts occluders. The semi-direct restoration was made in Filtek Z350 XT composite resin, respecting the anatomy of tooth 36. Pigments were used to improve aesthetic details. After finishing and polishing, the piece was conditioned and cemented with Relyx Ultimate dual cement. It can be concluded that the restorative approach using the semi-direct technique built on a semi-rigid model is a conservative and advantageous therapeutic option for teeth with extensive coronal destruction. This technique allows for effective restoration, ensuring both the aesthetics and adequate function of the affected tooth(AU)

Effects of Surface-Etching Systems on the Shear Bond Strength of Dual-Polymerized Resin Cement and Zirconia.

Adhesion of zirconia is difficult; thus, etching agents using several different methods are being developed. We investigated the effects of surface treatment with commercially available etching agents on the bond strength between zirconia and resin cement and compared them with those achieved using air abrasion alone. We used 100 zirconia blocks, of which 20 blocks remained untreated, 20 blocks were sandblasted, and 60 blocks were acid-etched using three different zirconia-etching systems: Zircos-E etching (strong-acid etching), smart etching (acid etching after air abrasion), and cloud etching (acid etching under a hot stream). Each group was subjected to a bonding procedure with dual-polymerized resin cement, and then 50 specimens were thermocycled. The shear bond strengths between the resin cement and zirconia before and after the thermocycling were evaluated. We observed that in the groups that did not undergo thermocycling, specimens surface-treated with solution did not show a significant increase in shear bond strength compared to the sandblasted specimens (p > 0.05). Among the thermocycled groups, the smart-etched specimens showed the highest shear bond strength. In the short term, various etching agents did not show a significant increase in bond strength compared to sandblasting alone, but in the long term, smart etching showed stability in bond strength (p < 0.05).

Experimental study on the mechanical properties of desert sand improved by the combination of additives and bio-cement.

Bio-cement is a green and energy-saving building material that has attracted much attention in the field of ecological environment and geotechnical engineering in recent years. The aim of this study is to investigate the use of bio-cement (enzyme-induced calcium carbonate precipitation-EICP) in combination with admixtures for the improvement of desert sands, which can effectively improve the mechanical properties of desert sands and is particularly suitable for sand-rich countries. In addition, the suitability of tap water in bio-cement was elucidated and the optimum ratio of each influencing factor when tap water is used as a solvent was derived. The results showed that peak values of unconfined compressive strength (maximum increase of about 130 times), shear strength (increase of 27.09%), calcium carbonate precipitation value (increase of about 4.39 times), and permeability (decrease of about 93.72 times) were obtained in the specimens modified by EICP combined with admixture as compared to the specimens modified by EICP only. The incorporation of skimmed milk powder, though significantly increasing the strength, is not conducive to cost control. The microscopic tests show that the incorporation of admixtures can provide nucleation sites for EICP, thus improving the properties of desert sand. This work can provide new research ideas for cross-fertilization between the disciplines of bio-engineering, ecology, and civil engineering.

Deformation and Annealing Behavior of Cr Coating Prepared by Pack-Cementation on the Surface of Austenitic Stainless Steel.

In this paper, a Cr coating was prepared by induction heating and pack-cementation chromizing on AISI 304 austenitic stainless steel. Then, the cold-rolling deformation and annealing treatment were introduced to refine the coarse matrix grains caused by pack-chromizing and improve the overall performance of 304 austenitic stainless steel. The phase composition, element distribution, and microstructure of the coating were carefully characterized. The microhardness, wear resistance, and corrosion resistance of the coating were tested. The results show that the Cr coating with a thickness of 100 µm is mainly composed of a (Cr,Fe)23C6, (Cr,Fe)7C3, and α-Fe-Cr solid solution. After the cold-rolling deformation and subsequent annealing treatment, the grains are significantly refined and the Cr coating is divided into two layers, consisting of carbon-chromium compounds such as Cr23C6, Cr7C3, Cr2C, and Cr3C2 in the surface layer and a Fe-Cr solid solution in the subsurface layer. The cold-rolling deformation and annealing treatment significantly improved the microhardness and wear resistance of the coated sample, and the corrosion resistance was also better than that of the uncoated sample.

5-year Clinical Performance of Ceramic Onlay and Overlay Restorations Luted with Light-cured Composite Resin.

OBJECTIVES: This prospective clinical trial evaluated the clinical performance of ceramic partial coverage indirect adhesive restorations (PCIARs) in posterior teeth luted with a light-cured composite resin. METHODS: From April 2016 to January 2017, a total of 60 patients (27 males, 33 females; mean age: 42.2±10.86 years old) received 83 glass-ceramic PCIARs (26 onlay, 57 overlay) made of IPS Emax CAD (Ivoclar Vivadent). All restorations were luted with a light-cured composite resin (Filtek Z250, 3M ESPE) by two operators. Two independent calibrated examiners blinded to the operators performing the treatment evaluated the restorations at baseline, 1-year, and 5-year following FDI World Dental Federation criteria including esthetic, functional, and biological properties. Data were analyzed with the Friedman test and the Wilcoxon sign test (p<0.05). RESULTS: None of the restorations failed due to fracture or retention loss. One restoration was clinically unsatisfactory because of secondary caries. Marginal staining (p:0.000), marginal adaptation (p:0.018) showed significant differences between 1-year and 5-year recall. CONCLUSIONS: The PCIARs demonstrated excellent clinical performance at 1-year period. The degradation parameters appeared as minor staining and minor irregularities after 5-year, without any affect on the clinical performance. CLINICAL SIGNIFICANCE: Our findings provide evidence that the clinical performance of PCIARs luted with a light-cured composite resin was clinically acceptable after a five-year evaluation period. Due to secondary caries, only one restoration was considered clinically unsatisfactory.

Evaluation of Vertical Discrepancies in Crown Seating Using Different Glass Ionomer Cement Volume: An In Vitro Study.

Background This in vitro study aimed to assess the vertical disparities in the positioning of complete crown castings when different quantities of cement were used and to determine the optimal amount of cement for cementation while minimizing any marginal discrepancies. Methodology A total of 60 ideal nickel-chromium (Ni-Cr) crown castings were divided into three groups of experimental volumes of glass ionomer cement, with 20 castings in each group. Group I had completely filled volume with cement, group II had it half-filled, and group III had brushed up cement internally. The crowns were cemented by applying a static load of 5 kg to the cementation apparatus for 10 minutes. The marginal discrepancy between the die and the castings was measured pre-cementation and post-cementation using image analysis software in combination with a stereomicroscope (Motic, USA) at predetermined points that were marked on the die. Statistical analysis was performed using Statistical Package for the Social Sciences (IBM SPSS Statistics for Windows, IBM Corp., Version 16, Armonk, USA) software. A one-way analysis of variance (ANOVA) was used for the intergroup analysis. A paired sample t-test was used for intragroup analysis. Result  Brushing cement onto the internal surface presented the least mean values (P<0.05) of post-pre-cementation vertical discrepancy (14.92±10.77 µm) when compared to the half-filled cement group (28.42±12.45 µm) and the fully-filled cement group (58.50±20.91 µm). Conclusion Cement volume appeared to be a key factor in the vertical marginal discrepancy of the crown. The cement brush applied to the internal surfaces of the crown showed smaller post-cementation vertical discrepancies.

Effects of a relined fiberglass post with conventional and self-adhesive resin cement.

Objectives: This study was conducted to evaluate the mechanical properties of relined and non-relined fiberglass posts when cemented to root canal dentin using a conventional dual-cure resin cement or a self-adhesive resin cement. Materials and Methods: Two types of resin cements were utilized: conventional and self-adhesive. Additionally, 2 cementation protocols were employed, involving relined and non-relined fiberglass posts. In total, 72 bovine incisors were cemented and subjected to push-out bond strength testing (n = 10) followed by failure mode analysis. The cross-sectional microhardness (n = 5) was assessed along the root canal, and interface analyses (n = 3) were conducted using scanning electron microscopy (SEM). Data from the push-out bond strength and cross-sectional microhardness tests were analyzed via 3-way analysis of variance and the Bonferroni post-hoc test (α = 0.05). Results: For non-relined fiberglass posts, conventional resin cement exhibited higher push-out bond strength than self-adhesive cement. Relined fiberglass posts yielded comparable results between the resin cements. Type II failure was the most common failure mode for both resin cements, regardless of cementation protocol. The use of relined fiberglass posts improved the cross-sectional microhardness values for both cements. SEM images revealed voids and bubbles in the incisors with non-relined fiberglass posts. Conclusions: Mechanical properties were impacted by the cementation protocol. Relined fiberglass posts presented the highest push-out bond strength and cross-sectional microhardness values, regardless of the resin cement used (conventional dual-cure or self-adhesive). Conversely, for non-relined fiberglass posts, the conventional dual-cure resin cement yielded superior results to the self-adhesive resin cement.

Contemporary Concepts of Adhesive Cementation of Glass-Fiber Posts: A Narrative Review.

(1) Background: Cementation of glass fiber posts to root canals has been associated with various failures, especially debonding. This narrative review aims to present the contemporary concepts concerning the adhesive cementation of glass fiber post and to discuss the optimal management of these factors. (2) Methods: Electronic search was performed in MEDLINE/Pub Med and Google Scholar using selected keywords examining the parameters post length, surface treatment of glass fiber posts, post space preparation and dentin pretreatment, resin cement selection, adhesive systems and hybrid layer formation, and clinical techniques. (3) Results: The search led to the selection of 44 articles. Epoxy resin-based endodontic sealers are recommended and the use of temporary cement in the root canal should be avoided. The minimum length of a glass fiber post adhesively cemented to a root canal is 5 mm. Irrigating the root canals with chlorhexidine, MTAD, or EDTA (alone or in combination with NaOCl) after post space preparation seems to enhance the bond strength. Silane application on the surface of the post seems to be beneficial. Concerning resin cements and adhesive systems, the results were rather inconclusive. Finally, resin cement should be applied inside the root canal with an elongation tip and photoactivation should be delayed. (4) Conclusions: Contemporary concepts of adhesive cementation of glass fiber posts can indeed improve the bond between glass fiber posts, resin cement, and root canal dentin, however, evidence coming from long-term randomized prospective clinical trials is needed in order to obtain safer conclusions.

Micro- and nano-Illite to improve strength of untreated-soil as a nano soil-improvement (NSI) technique.

Soil stabilization is a technique of improving the geotechnical properties of soils for various engineering applications. However, conventional stabilizers such as cement and lime have some limitations, such as high cost, environmental impact, and durability issues. Therefore, there is a need for alternative and innovative stabilizers that can overcome these challenges. This study introduces nano-Illite, a type of clay mineral, as a novel and effective soil stabilizer. Nano-Illite can form nano-cementation (NC) in soil, which is a process of enhancing the durability of various building materials. NC is also known as nano soil-improvement (NSI), a technique that has been developed in recent years. Four formulations of micro- and nano-Illite with concentrations of 0, 1, 2, and 3% were separately added to soil samples. The unconfined compressive strength (UCS) and the secant modulus at 50% of peak stress (E50) of the treated samples were measured and compared with the untreated samples. The results showed that 3% nano-Illite increased the UCS of soil by more than 2.2 times and the E50 by more than 1.5 times after 7 days of curing. Micro-Illite also improved the UCS and E50 of soil, but to a lesser extent. X-ray fluorescence (XRF), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analyses revealed the micro- and nano-structures of the soil specimens and the performance of Illite as a nano-additive. This research demonstrates the effectiveness of nano-Illite in soil improvement as a NSI technique, and its potential to replace or reduce the use of conventional stabilizers. This study also contributes to the understanding of the mechanisms and factors that influence the NC process in soil.

Bond Strength of Milled and Printed Zirconia to 10-Methacryloyloxydecyl Dihydrogen Phosphate (10-MDP) Resin Cement as a Function of Ceramic Conditioning, Disinfection and Ageing.

This study aimed to assess the suitability of printed zirconia (ZrO2) for adhesive cementation compared to milled ZrO2. Surface conditioning protocols and disinfection effects on bond strength were also investigated. ZrO2 discs (n = 14/group) underwent either alumina (Al2O3) airborne particle abrasion (APA; 50 µm, 0.10 MPa) or tribochemical silicatisation (TSC; 110 µm Al2O3, 0.28 MPa and 110 µm silica-modified Al2O3, 0.28 MPa), followed by disinfection (1 min immersion in 70% isopropanol, 15 s water spray, 10 s drying with oil-free air) for half of the discs. A resin cement containing 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) was used for bonding (for TSC specimens after application of a primer containing silane and 10-MDP). Tensile bond strength was measured after storage for 24 h at 100% relative humidity or after 30 days in water, including 7500 thermocycles. Surface conditioning significantly affected bond strength, with higher values for TSC specimens. Ageing and the interaction of conditioning, disinfection and ageing also impacted bond strength. Disinfection combined with APA mitigated ageing-related bond strength decrease but exacerbated it for TSC specimens. Despite these effects, high bond strengths were maintained even after disinfection and ageing. Adhesive cementation of printed ZrO2 restorations exhibited comparable bond strengths to milled ZrO2, highlighting its feasibility in clinical applications.

Optimization of culture medium to improve bio-cementation effect based on response surface method.

The main challenge in the large-scale application of MICP lies in its low efficiency and promoting biofilm growth can effectively address this problem. In the present study, a prediction model was proposed using the response surface method. With the prediction model, optimum concentrations of nutrients in the medium can be obtained. Moreover, the optimized medium was compared with other media via bio-cementation tests. The results show that this prediction model was accurate and effective, and the predicted results were close to the measured results. By using the prediction model, the optimized culture media was determined (20.0 g/l yeast extract, 10.0 g/l polypeptone, 5.0 g/l ammonium sulfate, and 10.0 g/l NaCl). Furthermore, the optimized medium significantly promoted the growth of biofilm compared to other media. In the medium, the effect of polypeptone on biofilm growth was smaller than the effect of yeast extract and increasing the concentration of polypeptone was not beneficial in promoting biofilm growth. In addition, the sand column solidified with the optimized medium had the highest strength and the largest calcium carbonate contents. The prediction model represents a platform technology that leverages culture medium to impart novel sensing, adjustive, and responsive multifunctionality to structural materials in the civil engineering and material engineering fields.

Hydroxyapatite nano-pillars on TI-6Al-4V: Enhancements in cell spreading and proliferation during cell/surface integration.

Despite the attractive combinations of cell/surface interactions, biocompatibility, and good mechanical properties of Ti-6Al-4V, there is still a need to enhance the early stages of cell/surface integration that are associated with the implantation of biomedical devices into the human body. This paper presents a novel, easy and reproducible method of nanoscale and nanostructured hydroxyapatite (HA) coatings on Ti-6Al-4V. The resulting nanoscale coatings/nanostructures are characterized using a combination of Raman spectroscopy, scanning electron microscopy equipped with energy dispersive x-ray spectroscopy. The nanostructured/nanoscale coatings are shown to enhance the early stages of cell spreading and integration of bone cells (hFOB cells) on Ti-6Al-4V surfaces. The improvements include the acceleration of extra-cellular matrix, cell spreading and proliferation by nanoscale HA structures on the coated surfaces. The implications of the results are discussed for the development of HA nanostructures for the improved osseointegration of Ti-6Al-4V in orthopedic and dental applications.

A State-Dependent Elasto-Plastic Model for Hydrate-Bearing Cemented Sand Considering Damage and Cementation Effects.

In order to optimize the efficiency and safety of gas hydrate extraction, it is essential to develop a credible constitutive model for sands containing hydrates. A model incorporating both cementation and damage was constructed to describe the behavior of hydrate-bearing cemented sand. This model is based on the critical state theory and builds upon previous studies. The damage factor Ds is incorporated to consider soil degradation and the reduction in hydrate cementation, as described by plastic shear strain. A computer program was developed to simulate the mechanisms of cementation and damage evolution, as well as the stress-strain curves of hydrate-bearing cemented sand. The results indicate that the model replicates the mechanical behavior of soil cementation and soil deterioration caused by impairment well. By comparing the theoretical curves with the experimental data, the compliance of the model was calculated to be more than 90 percent. The new state-dependent elasto-plastic constitutive model based on cementation and damage of hydrate-bearing cemented sand could provide vital guidance for the construction of deep-buried tunnels, extraction of hydrocarbon compounds, and development of resources.

Clivus-Cervical Stabilization through Transoral Approach in Patients with Craniocervical Tumor: Three Cases and Surgical Technical Note.

Craniocervical tumors lead to cervical pain, instability, and neurological symptoms, reducing the quality of life. Effective surgical intervention at the craniocervical junction (CCJ) is critical and complex, involving comprehensive approaches and advanced reconstructive techniques. This study, conducted at Mexico City's National Institute of Cancerology, focused on three surgical cases that occurred in 2023 involving tumors at the CCJ: two chordomas and one prostate adenocarcinoma. We utilized a specialized technique: clivus-cervical stabilization reinforced with a polymethylmethacrylate (PMMA)-filled cervical mesh. Postoperatively, patients showed marked neurological recovery and reduced cervical pain, with enhanced Karnofsky and Eastern Cooperative Oncology Group (ECOG) scores indicating improved life quality. The surgical technique provided excellent exposure and effective tumor resection, utilizing PMMA-filled cervical mesh for stability. Tumoral lesions at the CCJ causing instability can be surgically treated through a transoral approach. This type of approach should be performed with precise indications to avoid complications associated with the procedure.

Physicochemical and mechanical properties of preheated composite resins for luting ceramic laminates.

This study analyzed and compared the physicochemical and mechanical properties of preheated resin composite with light-cured resin cement for luting indirect restorations. 210 specimens of resin cement/resin composite were prepared according to preheating treatment heated (Htd) or not (NHtd). Light-cured resin cement (Variolink Veneer, Ivoclar), and resin composite (Microhybrid-Z100, 3 M; Nanohybrid-Empress direct, Ivoclar; and Bulk fill-Filtek One, 3 M) were used (n = 10). Resin cement specimens were not preheated. The response variables were (n = 10): film thickness, microhardness, liquid sorption and solubility. Data were analyzed by 2-way ANOVA and Tukey HSD post-test (α = 0.05). Bulk fill NHtd resin had the highest film thickness values (p < 0.001). Microhybrid and nanohybrid Htd resins had the smallest thicknesses and did not differ from the cement (p > 0.05). The highest microhardness values were found for Bulk fill NHtd and Bulk fill Htd resins. The nanohybrid and microhybrid Htd resins showed the lowest microhardness values, with no difference in cement (p > 0.05). For liquid sorption, there was no significant difference between the groups (p = 0.1941). The microhybrid Htd resin showed higher solubility values than the other materials (p = 0.0023), but it did not differ statistically from resin cement (p > 0.05). Preheating composite resins reduced the film thickness. After heating, nanohybrid and Bulk fill resins retained stable microhardness, sorption, and solubility values.

Effect of Porosity/Binder Index on Strength, Stiffness and Microstructure of Cemented Clay: The Impact of Sustainable Development Geomaterials.

Searching for alternative material options to reduce the extraction of natural resources is essential for promoting a more sustainable world. This is especially relevant in construction and infrastructure projects, where significant volumes of materials are used. This paper aims to introduce three alternative materials, crushed ground glass (GG), recycled gypsum (GY) and crushed lime waste (CLW), byproducts of construction industry geomaterials, to enhance the mechanical properties of clay soil in Cartagena de Indias, Colombia. These materials show promise as cementitious and frictional agents, combined with soil and cement. Rigorous testing, including tests on unconfined compressive strength (qu) and initial stiffness (Go) and with a scanning electron microscope (SEM), reveals a correlation between strength, stiffness and the novel porosity/binder index (η/Civ) and provides mixed design equations for the novel geomaterials. Micro-level analyses show the formation of hydrated calcium silicates and complex interactions among the waste materials, cement and clay. These new geomaterials offer an eco-friendly alternative to traditional cementation, contributing to geotechnical solutions in vulnerable tropical regions.

Evaluation of the ceramic laminate veneer-tooth interface after different resin cement excess removal techniques.

OBJECTIVES: To compare, in vitro, resin cement excess removal techniques at the veneer-tooth interface. MATERIALS AND METHODS: Anterior human teeth were restored with ceramic veneers and randomly divided according to the following techniques (n = 10): removal of excess resin cement with brush and dental floss, followed by light-curing with Valo (Group 1) or Elipar (Group 2) for 1 min and 40 s; tack-curing with Valo (Group 3) or Elipar (Group 4) for 1 s; and tack-curing with Valo (Group 5) or Elipar (Group 6) for 5 s. The tack-curing was followed by removal of excess with probe and dental floss and light-curing for 1 min and 40 s. The area of excess resin cement (mm2) was measured in micro-CT images using AutoCAD program. The failures at the cervical margin in the X, Y, and Z axes (µm) of greater value were measured using the DataViewer program. The specimens were submitted to microleakage with 2% basic fuchsin. RESULTS: According to the Kruskal-Wallis and multiple comparison test, the highest area of excess resin cement was found in Group 1 (5.06 mm2), which did not differ statistically from Groups 2 (3.70 mm2) and 5 (2.19 mm2). Groups 2, 3 (1.73 mm2), 4 (1.14 mm2), and 5 (2.18 mm2) did not differ statistically. Group 6 (0.77 mm2) obtained the lowest value, which did not differ statistically from Groups 3 and 4. According to the Kruskal-Wallis and Dunn test, there was no significant difference in failures in X (p = 0.981), Y (p = 0.860), and Z (p = 0.638) axes and no significant difference in microleakage (p = 0.203) among the groups. CONCLUSIONS: Tack-curing for 1 s or 5 s, followed by removal of excess resin cement using a probe and a dental floss, tended to result in a lower amount of excess material around the margin. CLINICAL RELEVANCE: The technique used for resin cement excess removal influences the amount of excess leaved at the veneer-tooth interface. Tack-curing for 1 s or 5 s is recommended to mitigate the excess resin cement.

Evaluation of a water-based spacer fluid with additives for mud removal in well cementing operations.

This research evaluates the crucial role of effective well cementing in enhancing petroleum production, with a specific emphasis on the utilization of spacer fluids for pre-cementing well cleaning. Investigating the performance of a water-based spacer fluid enriched with barite, Xanthan Gum, potato starch, and Poly-Anionic Cellulose additives, this study systematically designs and evaluates three distinct spacer fluids featuring varied additive concentrations for optimal mud removal efficiency. Notably, Spacer B1, incorporating 0.51% PAC-LV and 0.51% starch, emerges as the most successful, exhibiting an impressive 67.84% mud removal rate. The flow behavior of the spacers is aptly described by the Herschel-Buckley model, providing valuable insights into their rheological characteristics. Rigorous compatibility tests affirm the absence of fluid incompatibility, instilling confidence in the chosen spacer compositions. Introducing a 5% surfactant results in a noteworthy 7-8% average increase in mud removal from the metal cylinder wall. In summary, this study contributes valuable perspectives on optimizing both well cementing practices and spacer fluid formulations, ultimately elevating efficiency in petroleum production processes.

Effect of laser remelting power on the microstructure and properties of vanadizing layer on AISI 52100 steel pin shaft.

The surface of AISI 52100 steel was pre-treated by laser remelting with different powers, and the vanadizing layer were prepared on remelted steel by pack cementation. The microstructure and properties of vanadizing layer were investigated by XRD, microhardness tester, metallographic microscope, scanning electron microscope, energy dispersive spectrometer, friction and wear tester. The critical load Lc was determined by observing the micro-scratch morphology of scratches through micro-scratch experiments, and its wear performance was studied. The results show that the hardness of remelting zone increase with the increase of laser power. When the laser power is 500 W, the microhardness is 424.6 HV0.2. The vanadizing layer formed on the remelting surfaces is uniform and dense. The layers are mainly composed of VCx phase and α-Fe/α'-Fe phase, the VC phase has the preferred orientation of (200) and (111) planes. There is a good metallurgical bonding between the vanadizing layer and the steel， and the thickness is 2.7 µm-12.15 µm, the microhardness is 2050.7 HV0.2-2350.9 HV0.2. When the laser remelting power is 300 W, the vanadizing layer is better in thickness, microhardness and average friction coefficient, the bonding force Lc between the vanadizing layer and the substrate is about 41.59 N, and the main failure mode is the spalling of the vanadizing layer. It can be concluded that laser remelting pre-treatment can greatly improve the hardness and wear resistance.

Mapping the Landscape of the Digital Workflow of Esthetic Veneers from Design to Cementation: A Systematic Review.

The purpose of this systematic review was to map all the existing literature on digitally designed and fabricated esthetic veneers. We aimed to compare the accuracy of digitally designed preparation and cementation guides for esthetic indirect veneers with the conventional workflow. We evaluated studies comparing the accuracy and predictability of workflows between digitally fabricated indirect-esthetic veneers and conventional indirect veneers. Searches were performed in August 2023 across three databases, specifically Google Scholar, Cochrane, and PubMed, and were restricted to English-language publications. The search strategy was based on the PICO criteria. Reference lists of identified articles were manually checked to find further pertinent studies that were not discovered during the electronic search. The titles and abstracts were reviewed in the first stage, and then the full article texts were reviewed and cross-matched against the predetermined inclusion criteria. Following the search, 169 articles were identified: 41 from Google Scholar, 44 from Cochrane, and 71 from PubMed, with 13 added manually. Of these, 20 were chosen for a detailed quality assessment of the digital veneer workflow and the accuracy of digital preparations and cementation guides for laminate veneers. Based on our findings, the digitally fabricated laminate-veneer workflow demonstrated superior predictability and accuracy compared to the conventional workflow.