Enhance Ethanol Sensing Performance of Fe-Doped Tetragonal SnO2 Films on Glass Substrate with a Proposed Mathematical Model for Diffusion in Porous Media.

This research enhances ethanol sensing with Fe-doped tetragonal SnO2 films on glass, improving gas sensor reliability and sensitivity. The primary objective was to improve the sensitivity and operational efficiency of SnO2 sensors through Fe doping. The SnO2 sensors were synthesized using a flexible and adaptable method that allows for precise doping control, with energy-dispersive X-ray spectroscopy (EDX) confirming homogeneous Fe distribution within the SnO2 matrix. A morphological analysis showed a surface structure ideal for gas sensing. The results demonstrated significant improvement in ethanol response (1 to 20 ppm) and lower temperatures compared to undoped SnO2 sensors. The Fe-doped sensors exhibited higher sensitivity, enabling the detection of low ethanol concentrations and showing rapid response and recovery times. These findings suggest that Fe doping enhances the interaction between ethanol molecules and the sensor surface, improving performance. A mathematical model based on diffusion in porous media was employed to further analyze and optimize sensor performance. The model considers the diffusion of ethanol molecules through the porous SnO2 matrix, considering factors such as surface morphology and doping concentration. Additionally, the choice of electrode material plays a crucial role in extending the sensor's lifespan, highlighting the importance of material selection in sensor design.

Gas Sensor Based on Highly Effective Slot-Die Printed PEDOT:PSS@ZnO Hybrid Nanocomposite for Methanol Detection.

This study presents the development of gas sensors based on the PEDOT:PSS@ZnO hybrid active layer slot-die printing aqueous ink. Two different zinc oxide (ZnO) nanoparticles were studied to form the nanocomposites, as well as the use of glass and PET substrates to manufacture the devices. Despite the influence of the morphology of the active layer, all device variations studied here exhibited high response values for methanol gas at room temperature, in addition to presenting good repeatability, reversibility, and the possibility of technology transfer to flexible substrates. Furthermore, PEDOT:PSS@ZnO showed good selectivity to methanol compared to ethanol, ammonia, and CO2. The best devices showed responses greater than 700% in detecting methanol.

Thickness dependence of the room-temperature ethanol sensor properties of Cu2O polycrystalline films.

This study investigates the fabrication process of copper thin films via thermal evaporation, with precise control over film thickness achieved throughZ-position adjustment. Analysis of the as-fabricated copper films reveals a discernible relationship between grain size (〈D〉) andZ-position, characterized by a phenomenological equation〈D〉XRDn(Z)=〈D〉0n1+32rZ2+158rZ4, which is further supported by a growth exponent (n) of 0.41 obtained from the analysis. This value aligns well with findings in the literature concerning the growth of copper films, thus underlining the validity and reliability of our experimental outcomes. The resulting crystallites, ranging in size from 20 to 26 nm, exhibit a resistivity within the range of 3.3-4.6µΩ · cm. Upon thermal annealing at 200 °C, cuprite Cu2O thin films are produced, demonstrating crystallite sizes ranging from ∼9 to ∼24 nm with increasing film thickness. The observed monotonic reduction in Cu2O crystallites relative to film thickness is attributed to a recrystallization process, indicating amorphization when oxygen atoms are introduced, followed by the nucleation and growth of newly formed copper oxide phase. Changes in the optical bandgap of the Cu2O films, ranging from 2.31 to 2.07 eV, are attributed mainly to the quantum confinement effect, particularly important in Cu2O with size close than the Bohr exciton diameter (5 nm) of the Cu2O. Additionally, correlations between refractive index and extinction coefficient with film thickness are observed, notably a linear relationship between refractive index and charge carrier density. Electrical measurements confirm the presence of a p-type semiconductor with carrier concentrations of ∼1014cm-3, showing a slight decrease with film thickness. This phenomenon is likely attributed to escalating film roughness, which introduces supplementary scattering mechanisms for charge carriers, leading to a resistivity increase, especially as the roughness approaches or surpasses the mean free path of charge carriers (8.61 nm). Moreover,ab-initiocalculations on the Cu2O crystalline phase to investigate the impact of hydrostatic strain on its electronic and optical properties was conducted. We believe that our findings provide crucial insights that support the elucidation of the experimental results. Notably, thinner cuprite films exhibit heightened sensitivity to ethanol gas at room temperature, indicating potential for highly responsive gas sensors, particularly for ethanol breath testing, with significant implications for portable device applications.

Synthesis and Sensing Response of Magnesium Antimoniate Oxide (MgSb2O6) in the Presence of Propane Atmospheres at Different Operating Voltages.

Nanoparticles of MgSb2O6 were synthesized using a microwave-assisted wet chemistry method, followed by calcination at 700 °C. Their ability to detect different concentrations of propane gas (C3H8) at various operating voltages was evaluated. The material's crystalline phase was identified using X-ray powder diffraction (XRD). The morphology was analyzed by scanning electron microscopy (SEM), finding bar- and polyhedron-type geometries. Through transmission electron microscopy (TEM), we found particle sizes of 8.87-99.85 nm with an average of ~27.63 nm. Employing ultraviolet-visible (UV-Vis) spectroscopy, we found a band gap value of ~3.86 eV. Thick films made with MgSb2O6 powders were exposed to atmospheres containing 150, 300, 400, and 600 ppm of propane gas for dynamic testing. The time-dependent sensitivities were ~61.09, ~88.80, ~97.65, and ~112.81%. In addition, tests were carried out at different operating voltages (5-50 V), finding very short response and recovery times (~57.25 and ~18.45 s, respectively) at 50 V. The excellent dynamic response of the MgSb2O6 is attributed mainly to the synthesis method because it was possible to obtain nanometric-sized particles. Our results show that the trirutile-type oxide MgSb2O6 possesses the ability, efficiency, and thermal stability to be applied as a gas sensor for propane.

Gas Sensing and Half-Metallic Materials Design Using Metal Embedded into S Vacancies in WS2 Monolayers: Adsorption of NO, CO, and O2 Molecules.

The adsorption of CO, NO, and O2 molecules onto Cu, Ag, and Au atoms placed in the S vacancies of a WS2 monolayer was elucidated within dispersion-corrected density functional theory. The binding energies computed for embedded defects into S vacancies were 2.99 (AuS), 2.44 (AgS), 3.32 eV (CuS), 3.23 (Au2S2), 2.55 (Ag2S2), and 3.48 eV/atom (Cu2S2), respectively. The calculated diffusion energy barriers from an S vacancy to a nearby site for Cu, Ag, and Au were 2.29, 2.18, and 2.16 eV, respectively. Thus, the substitutional atoms remained firmly fixed at temperatures above 700 K. Similarly, the adsorption energies showed that nitric oxide and carbon oxide molecules exhibited stronger chemisorption than O2 molecules on any of the metal atoms (Au, Cu, or Ag) placed in the S vacancies of the WS2 monolayer. Therefore, the adsorption of O2 did not compete with NO or CO adsorption and did not displace them. The density of states showed that a WS2 monolayer modified with a Cu, Au, or Ag atom could be used to design sensing devices, based on electronic or magnetic properties, for atmospheric pollutants. More interestingly, the adsorption of CO changed only the electronic properties of the MoS2-AuS monolayer, which could be used for sensing applications. In contrast, the O2 molecule was chemisorbed more strongly than CO or NO on Au2S2, Cu2S2, or Ag2S2 placed into di-S vacancies. Thus, if the experimental system is exposed to air, the low quantities of O2 molecules present should result in the oxidation of the metallic atoms. Furthermore, the O2 molecules adsorbed on WS2-Au2S2 and WS2-CuS introduced a half-metallic behavior, making the system suitable for applications in spintronics.

Improving Hazardous Gas Detection Behavior with Palladium Decorated SnO2 Nanobelts Networks.

Transparent Conductive Oxides (TCOs) have been widely used as sensors for various hazardous gases. Among the most studied TCOs is SnO2, due to tin being an abundant material in nature, and therefore being accessible for moldable-like nanobelts. Sensors based on SnO2 nanobelts are generally quantified according to the interaction of the atmosphere with its surface, changing its conductance. The present study reports on the fabrication of a nanobelt-based SnO2 gas sensor, in which electrical contacts to nanobelts are self-assembled, and thus the sensors do not need any expensive and complicated fabrication processes. The nanobelts were grown using the vapor-solid-liquid (VLS) growth mechanism with gold as the catalytic site. The electrical contacts were defined using testing probes, thus the device is considered ready after the growth process. The sensorial characteristics of the devices were tested for the detection of CO and CO2 gases at temperatures from 25 to 75 °C, with and without palladium nanoparticle deposition in a wide concentration range of 40-1360 ppm. The results showed an improvement in the relative response, response time, and recovery, both with increasing temperature and with surface decoration using Pd nanoparticles. These features make this class of sensors important candidates for CO and CO2 detection for human health.

Photocatalytic Evaluation and Application as a Sensor for the Toxic Atmospheres (Propane and Carbon Monoxide) of Nickel Antimonate (NiSb2O6) Powders.

Nickel antimonate (NiSb2O6) powders were synthesized using a wet chemistry process assisted by microwave radiation and calcination from 600 to 700 °C to evaluate their photocatalytic and gas-sensing properties. The crystalline phase obtained at 800 °C of trirutile-type nickel antimonate was confirmed with powder X-ray diffraction. The morphology and size of the nanostructures were analyzed employing electron microscopy (SEM and TEM), identifying irregular particles and microrods (~277 nm, made up of polyhedral shapes of size ~65 nm), nanorods with an average length of ~77 nm, and nanostructures of polyhedral type of different sizes. UV-vis analysis determined that the bandgap of the powders obtained at 800 °C was ~3.2 eV. The gas sensing tests obtained a maximum response of ~5 for CO (300 ppm) at 300 °C and ~10 for C3H8 (500 ppm) at 300 °C. According to these results, we consider that NiSb2O6 can be applied as a gas sensor. On the other hand, the photocatalytic properties of the antimonate were examined by monitoring the discoloration of malachite green (MG) at five ppm. MG concentration monitoring was carried out using UV-visible spectroscopy, and 85% discoloration was achieved after 200 min of photocatalytic reaction.

Selective NO2 Detection of CaCu3Ti4O12 Ceramic Prepared by the Sol-Gel Technique and DRIFT Measurements to Elucidate the Gas Sensing Mechanism.

NO2 is one of the main greenhouse gases, which is mainly generated by the combustion of fossil fuels. In addition to its contribution to global warming, this gas is also directly dangerous to humans. The present work reports the structural and gas sensing properties of the CaCu3Ti4O12 compound prepared by the sol-gel technique. Rietveld refinement confirmed the formation of the pseudo-cubic CaCu3Ti4O12 compound, with less than 4 wt% of the secondary phases. The microstructural and elemental composition analysis were carried out using scanning electron microscopy and X-ray energy dispersive spectroscopy, respectively, while the elemental oxidation states of the samples were determined by X-ray photoelectron spectroscopy. The gas sensing response of the samples was performed for different concentrations of NO2, H2, CO, C2H2 and C2H4 at temperatures between 100 and 300 °C. The materials exhibited selectivity for NO2, showing a greater sensor signal at 250 °C, which was correlated with the highest concentration of nitrite and nitrate species on the CCTO surface using DRIFT spectroscopy.

A review on MXene and its nanocomposites for the detection of toxic inorganic gases.

In the search of the viable candidate for the sensing of pollutant gases, two-dimensional (2D) material transition metal carbides (MXenes) have attracted immense attention due to their outstanding physical and chemical properties for sensing purposes. The formation of unique 2D layered structure with high conductivity, large mechanical strength, and high adsorption properties furnish their strong interactions with gaseous molecules, which holds a promising place for developing ideal gas sensing devices. This review looks at recent achievements in diversified MXenes, with a focus gaining on in-depth understanding of MXene-based materials in room temperature inorganic gas sensors through both theoretical and experimental studies. In the first part of the review, the properties and advantages of sensing material (MXene) in comparison with other 2D materials are discussed. In the second part, the unique advantages of chemiresistive based sensors and the demerits of other detection methods are summarized in detail. This section is followed by the unique structural design of MXene bases materials for improving the sensing performance towards detection of inorganic gases. The interaction between MXene and the adsorbed gases on its surface is discussed, with a possible sensing mechanism. Finally, an overview of the current progress and opportunities for the demand of MXene is emphasized and perspectives for future improvement of the design of MXene in gas sensors are highlighted. Therefore, this review highlights the opportunities and the advancement in 2D material-based gas sensors which could provide a new avenue for rapid detection of toxic gases in the environment.

Tunable Low Crystallinity Carbon Nanotubes/Silicon Schottky Junction Arrays and Their Potential Application for Gas Sensing.

Highly ordered nanostructure arrays have attracted wide attention due to their wide range of applicability, particularly in fabricating devices containing scalable and controllable junctions. In this work, highly ordered carbon nanotube (CNT) arrays grown directly on Si substrates were fabricated, and their electronic transport properties as a function of wall thickness were explored. The CNTs were synthesized by chemical vapor deposition inside porous alumina membranes, previously fabricated on n-type Si substrates. The morphology of the CNTs, controlled by the synthesis parameters, was characterized by electron microscopies and Raman spectroscopy, revealing that CNTs exhibit low crystallinity (LC). A study of conductance as a function of temperature indicated that the dominant electric transport mechanism is the 3D variable range hopping. The electrical transport explored by I-V curves was approached by an equivalent circuit based on a Schottky diode and resistances related to the morphology of the nanotubes. These junction arrays can be applied in several fields, particularly in this work we explored their performance in gas sensing mode and found a fast and reliable resistive response at room temperature in devices containing LC-CNTs with wall thickness between 0.4 nm and 1.1 nm.

Electronic nose dataset for COPD detection from smokers and healthy people through exhaled breath analysis.

This article presents a database which was obtained by acquiring measurements through a multisensory device called Electronic Nose (E-nose) based on a matrix of metal oxide sensors, in order to discriminate and classify a group of people affected by the respiratory disease Chronic Obstructive Pulmonary Disease (COPD), smokers and healthy control people through exhaled breath analysis. The database consists of 4 groups of measurements which were acquired through the E-nose system: 10 control samples (healthy people), 20 samples of people with COPD, 4 samples of smokers and 10 air samples, where in each group two samples of exhaled breath per person were acquired giving a total of 78 samples (40 from COPD, 20 from control, 8 from smokers and 10 from the air).

Ionogels Based on a Single Ionic Liquid for Electronic Nose Application.

Ionogel are versatile materials, as they present the electrical properties of ionic liquids and also dimensional stability, since they are trapped in a solid matrix, allowing application in electronic devices such as gas sensors and electronic noses. In this work, ionogels were designed to act as a sensitive layer for the detection of volatiles in a custom-made electronic nose. Ionogels composed of gelatin and a single imidazolium ionic liquid were doped with bare and functionalized iron oxide nanoparticles, producing ionogels with adjustable target selectivity. After exposing an array of four ionogels to 12 distinct volatile organic compounds, the collected signals were analyzed by principal component analysis (PCA) and by several supervised classification methods, in order to assess the ability of the electronic nose to distinguish different volatiles, which showed accuracy above 98%.

Discrimination Improvement of a Gas Sensors' Array Using High-Frequency Quartz Crystal Microbalance Coated with Polymeric Films.

The discrimination improvement of an array of four highly sensitive 30 MHz gas quartz crystal microbalance (QCM) sensors was performed and compared to a similar system based on a 12-MHz QCM. The sensing polymeric films were ethyl cellulose (EC), poly-methyl methacrylate (PMMA), Apiezon L (ApL), and Apiezon T (ApT) and they were coated over the AT-cut QCM devices by the drop casting technique. All the sensors had almost the same film thickness (0.2 µm). The fabricated QCM sensor arrays were exposed to three different concentrations, corresponding to 5, 10, and 15 µL, of ethanol, ethyl acetate, and heptane vapors. The steady state sensor responses were measured in a static system at a temperature of 20 °C and relative humidity of 22%. Our results showed that the 30-MHz sensors have a higher sensitivity than 12-MHz ones (around 5.73 times), independently of the sensing film and measured sample. On the other hand, principal component analysis and discriminant analysis were performed using the raw data of the responses. An improvement of the classification percentage between 12 MHz and 30 MHz sensors was found. However, it was not sufficient, especially for low concentrations. Furthermore, using partition coefficient and discriminant analysis (DA), an improvement of 100% classification of the three samples was achieved for the case of the 30-MHz sensor array.

Studies of hydrogen sulfide and ammonia adsorption on P- and Si-doped graphene: density functional theory calculations.

Studies of hydrogen sulfide (H2S) and ammonia (NH3) adsorption on phosphorus (P) and silicon (Si) doped graphene are performed by ab initio calculations using the periodic density functional theory (DFT). The P and Si incorporation in graphene distorts the unit cell altering the bond lengths and angles. Unlike the pristine, the phosphorus-doped graphene shows a metallic behavior, and the silicon-doped graphene is a semiconductor with an energy gap of 0.25 eV. Moreover, the electronic properties of phosphorus-doped graphene may change with the adsorption of hydrogen sulfide and ammonia. However, the silicon-doped graphene only shows changes with the adsorption of hydrogen sulfide. In addition, the silicon-doped graphene exhibits chemisorption when interacting with ammonia. According to the obtained results, phosphorus-doped graphene is suitable as a gas sensor of hydrogen sulfide and ammonia, in contrast with the silicon-doped structure, which may be used as a sensor of hydrogen sulfide. Graphical Abstract Ammonia adsorption on Si-doped graphene.

All-Fiber CO2 Sensor Using Hollow Core PCF Operating in the 2 µm Region.

A realistic implementation of an all-fiber CO2 sensor, using 74 cm of hollow core photonic crystal fiber (HC-PCF) as the cavity for light/gas interaction, has been implemented. It is based on CO2 absorbance in the 2 µm region. The working range is from 2% to 100% CO2 concentration at 1 atm total pressure and the response time obtained was 10 min. Depending on the concentration level, the sensor operates at one of three different wavelengths (2003.5 nm, 1997.0 nm and 1954.5 nm) to maintain a high sensitivity across all the working range.

ZIF Nanocrystal-Based Surface Acoustic Wave (SAW) Electronic Nose to Detect Diabetes in Human Breath.

In the present work, a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based on zeolitic imidazolate frameworks, ZIF-8 and ZIF-67 nanocrystals (pure and combined with gold nanoparticles), as sensitive layers has been tested as a non-invasive system to detect different disease markers, such as acetone, ethanol and ammonia, related to the diagnosis and control of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous sensitive layers at the surface of the SAW device. Low concentrations (5 ppm, 10 ppm and 25 ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

A Gas Sensor Based on a Single SnO Micro-Disk.

In this study, individual nanofabricated SnO micro-disks, previously shown to exhibit exceptional sensitivity to NOx, are investigated to further our understanding of gas sensing mechanisms. The SnO disks presenting different areas and thickness were isolated and electrically connected to metallic electrodes aided by a Dual Beam Microscope (SEM/FIB). While single micro-disk devices were found to exhibit short response and recovery times and low power consumption, large interconnected arrays of micro-disks exhibit much higher sensitivity and selectivity. The source of these differences is discussed based on the gas/solid interaction and transport mechanisms, which showed that thickness plays a major role during the gas sensing of single-devices. The calculated Debye length of the SnO disk in presence of NO2 is reported for the first time.

Reduction of the Measurement Time by the Prediction of the Steady-State Response for Quartz Crystal Microbalance Gas Sensors.

This paper presents a new approach to reduce the measurement time by the prediction of the steady-state using the transient response to ethanol for quartz crystal microbalance gas sensors coated with ethyl cellulose. The experimentally measured response curves were successively fitted using a mathematical model based on the sum of two exponentials with different time constants. The parameters of the model were determined, and the time constants and the magnitude of the steady-state response were analyzed. Even though the time constants did not stabilize well, the parameter corresponding to the magnitude of the steady-state response quickly converged and stabilized after 37 s. Moreover, this calculated parameter was highly correlated with the measured values of the steady-state response, which was measured at five times the longest time constant (83 s) of the model. Therefore, the steady-state response could be predicted with a 55% reduction in the measurement (detection) time.

Exhaled breath analysis for gastric cancer diagnosis in Colombian patients.

We present here the first study that directly correlates gastric cancer (GC) with specific biomarkers in the exhaled breath composition on a South American population, which registers one of the highest global incidence rates of gastric affections. Moreover, we demonstrate a novel solid state sensor that predicts correct GC diagnosis with 97% accuracy. Alveolar breath samples of 30 volunteers (patients diagnosed with gastric cancer and a controls group formed of patients diagnosed with other gastric diseases) were collected and analyzed by gas-chromatography/mass-spectrometry (GC-MS) and with an innovative chemical gas sensor based on gold nanoparticles (AuNP) functionalized with octadecylamine ligands. Our GC-MS analyses identified 6 volatile organic compounds that showed statistically significant differences between the cancer patients and the controls group. These compounds were different from those identified in previous studied performed on other populations with high incidence rates of this malady, such as China (representative for Eastern Asia region) and Latvia (representative for Baltic States), attributable to lifestyle, alimentation and genetics differences. A classification model based on principal component analysis of our sensor data responses to the breath samples yielded 97% accuracy, 100% sensitivity and 93% specificity. Our results suggest a new and non-intrusive methodology for early diagnosis of gastric cancer that may be deployed in regions lacking well-developed health care systems as a prediagnosis test for selecting the patients that should undergo deeper investigations (e.g., endoscopy and biopsy).

Sensitivity Tests of Pellets Made from Manganese Antimonate Nanoparticles in Carbon Monoxide and Propane Atmospheres.

Nanoparticles of manganese antimonate (MnSb2O6) were prepared using the microwave-assisted colloidal method for its potential application as a gas sensor. For the synthesis of the oxide, manganese nitrate, antimony chloride, ethylenediamine and ethyl alcohol (as a solvent) were used. The precursor material was calcined at 800 °C in air and analyzed by X-ray diffraction. The oxide crystallized into a hexagonal structure with spatial group P321 and cell parameters a = b = 8.8054 Å and c = 4.7229 Å. The microstructure of the material was analyzed by scanning electron microscopy (SEM), finding the growth of microrods with a size of around ~10.27 µm and some other particles with an average size of ~1.3 µm. Photoacoustic spectroscopy (PAS) studies showed that the optical energy band (Eg) of the oxide was of ~1.79 eV. Transmission electron microscopy (TEM) analyses indicated that the size of the nanoparticles was of ~29.5 nm on average. The surface area of the powders was estimated at 14.6 m²/g by the Brunauer⁻Emmett⁻Teller (BET) method. Pellets prepared from the nanoparticles were tested in carbon monoxide (CO) and propane (C3H8) atmospheres at different concentrations (0⁻500 ppm) and operating temperatures (100, 200 and 300 °C). The pellets were very sensitive to changes in gas concentration and temperature: the response of the material rose as the concentration and temperature increased. The results showed that the MnSb2O6 nanoparticles can be a good candidate to be used as a novel gas sensor.