Multifunctional and Washable Carbon Nanotube-Wrapped Textile Yarns for Wearable E-Textiles.

Carbon nanotube (CNT) yarns are promising for wearable electronic applications due to their excellent electromechanical and thermal properties and structural flexibility. A spinning system was customized to produce CNT-wrapped textile yarns for wearable applications. By adjusting the spinning parameters and core yarn, a highly tailored hybrid CNT yarn could be produced for textile processing, e.g., knitting and weaving. The electrical resistance and mechanical properties of the yarn are influenced by the core yarn. The high flexibility of the yarn enabled state-of-the-art three-dimensional (3D) knitting of the CNT-wrapped yarn for the first time. Using the 3D knitted technology, CNT-wrapped textile yarns were seamlessly integrated into a wrist band and the index finger of a glove. The knitted structure exhibited a large resistance change under strain and precisely recorded the signal under the different movements of the finger and wrist. When the knitted fabric was connected to a power source, rapid heating above skin temperature was observed at a low voltage. This work presents a novel hybrid yarn for the first time, which sustained 30 washing cycles without performance degradation. By changing the core yarn, a highly stretchable and multimodal sensing system could be developed for wearable applications.

Washable and Breathable Electret Sensors Based on a Hydro-Charging Technique for Smart Textiles.

Flexible electromechanical sensors based on electret materials have shown great application potential in wearable electronics. However, achieving great breathability yet maintaining good washability is still a challenge for traditional electret sensors. Herein, we report a washable and breathable electret sensor based on a hydro-charging technique, namely, hydro-charged electret sensor (HCES). The melt-blown polypropylene (MBPP) electret fabric can be charged while washing with water. The surface potential of MBPP electret fabric can be improved by optimizing the type of water, water pressure, water temperature, drying temperature, drying time, ambient air pressure, and ambient relative humidity. It is proposed that the single fiber has charges of different polarities on the upper and lower surfaces due to contact electrification with water, thereby forming electric dipoles between fibers, which can lead to better surface potential stability than the traditional corona-charging method. The HCES can achieve a high air permeability of ∼215 mm/s and sensitivity up to ∼0.21 V/Pa, with output voltage remaining stable after over 36,000 working cycles and multiple times of water washing. As a demonstration example, the HCES is integrated into a chest strap to monitor human respiration conditions.

Destructive-Treatment-Free Rapid Polymer-Assisted Metal Deposition for Versatile Electronic Textiles.

Highly conductive, durable, and breathable metal-coated textiles are critical building block materials for future wearable electronics. In order to enhance the metal adhesion on the textile surface, existing solution-based approaches to preparing these materials require time-consuming presynthesis and/or premodification processes, typically in the order of tens of minutes to hours, on textiles prior to metal plating. Herein, we report a UV-induced rapid polymer-assisted metal deposition (r-PAMD) that offers a destructive-treatment-free process to deposit highly conductive metals on a wide variety of textile materials, including cotton, polyester, nylon, Kevlar, glass fiber, and carbon cloth. In comparison to the state of the arts, r-PAMD significantly shortens the modification time to several minutes and is compatible with the roll-to-roll fabrication manner. Moreover, the deposited metals show outstanding adhesion, which withstands rigorous flexing, abrasion, and machine washing tests. We demonstrate that these metal-coated textiles are suitable for applications in two vastly different fields, being wearable and washable sensors, and lithium batteries.

A Study of the Performance Degradation of Conductive Threads Based on the Effects of Tensile Forces and Repeated Washing.

In recent years, after the ongoing success in the creation of portable electronic devices, an increasing effort has been put in creating wearable devices capable of sensing multiple parameters while being imperceptible to the user. A field that has recently gained attention due to this is that of textile electronics. For this purpose, one of the most commonly used materials is conductive threads, capable of sustaining an electrical connection, while at the same time being part of a garment. As research on the performance and stability of such threads is scarce, the aim of this work is to study the effects of tension on readily available conductive threads and to verify their suitability and reliability for e-textile applications. After testing seven commercially available threads, this study demonstrates that the nominal parameters provided by the manufacturers are not in line with experimentation, and that both embroidery and washing have an impact on their performance.

Washable Fabric Triboelectric Nanogenerators for Potential Application in Face Masks.

In order to counteract the COVID-19 pandemic by wearing face masks, we examine washable fabric-based triboelectric nanogenerators (FTENGs). We applied the flash-spun nonwoven fabric (FS fabric) into the FTENGs, comparing the melt-blown nonwoven fabric (MB fabric) based FTENGs, which is conventionally studied in the field of energy harvesting. For reusability, all our proposed FTENGs are systematically investigated by controlling the washing conditions. After washing, the degradation ratio of the obtained output voltage is found to be only 12.5% for FS FTENGs, compared to the ratio of about 50% for the typical MB FTENGs. A rather small degradation ratio for FS fabric cases has resulted from less changed fabric structure after washing due to more dense fabric nature. Additionally, in order to improve the electrical characteristics of FS FTENGs. Note that the output voltage of FTENGs exhibits as much as 600 V.

Advances in the Robustness of Wearable Electronic Textiles: Strategies, Stability, Washability and Perspective.

Flexible electronic textiles are the future of wearable technology with a diverse application potential inspired by the Internet of Things (IoT) to improve all aspects of wearer life by replacing traditional bulky, rigid, and uncomfortable wearable electronics. The inherently prominent characteristics exhibited by textile substrates make them ideal candidates for designing user-friendly wearable electronic textiles for high-end variant applications. Textile substrates (fiber, yarn, fabric, and garment) combined with nanostructured electroactive materials provide a universal pathway for the researcher to construct advanced wearable electronics compatible with the human body and other circumstances. However, e-textiles are found to be vulnerable to physical deformation induced during repeated wash and wear. Thus, e-textiles need to be robust enough to withstand such challenges involved in designing a reliable product and require more attention for substantial advancement in stability and washability. As a step toward reliable devices, we present this comprehensive review of the state-of-the-art advances in substrate geometries, modification, fabrication, and standardized washing strategies to predict a roadmap toward sustainability. Furthermore, current challenges, opportunities, and future aspects of durable e-textiles development are envisioned to provide a conclusive pathway for researchers to conduct advanced studies.

Breathable and Wearable Strain Sensors Based on Synergistic Conductive Carbon Nanotubes/Cotton Fabrics for Multi-directional Motion Detection.

Flexible strain-sensitive sensors have been receiving intensive attention in many aspects ranging from human motion capture to health-related signal monitoring. However, the fabric strain sensor with multi-directional sensing capability, besides having a wide strain range and high response sensitivity, is still very challenging and deserves further exploration. Here, we have prepared a wearable cotton fabric strain sensor uniformly decorated with single-walled carbon nanotubes through a facile solution process. The unique hierarchical architecture of the cotton fabric woven from twisted yarns combined with the conductive carbon nanotube network endows the fabric strain sensors with attractive performance, including low detection limit, large workable strain range, fascinating stability and durability, excellent direction-dependent strain response, and good air permeability. The strain sensor without polymer encapsulation can not only monitor subtle and large multi-directional motions but also fit well to the human body with satisfactory comfort, demonstrating its potential application in wearable electronics and intelligent clothing.

Preparation of Ag NPs and Its Multifunctional Finishing for Cotton Fabric.

To explore the combination of silver nanoparticles (Ag NPs) prepared in a green manner with cotton fabrics and the washing durability of the fabric after the combination. In this paper, the natural material, honeysuckle extract, was used as a reducing agent to prepare the Ag NPs' solution. The structure and size of Ag NPs were analyzed using ultraviolet-visible spectrophotometry (UV-vis), transmission electron microscopy (TEM), dynamic light scattering (DLS), X-ray powder diffraction (XRD), and Fourier transform infrared (FT-IR) spectroscopy characterization. The results showed that Ag+ was successfully reduced to Ag0 by the honeysuckle extract, the particle size was about 10.59 nm, and the potential was -42.9 mV, so it had strong electrostatic repulsion and good stability. Meanwhile, it was found that the synthesized Ag NPs were well coated by the honeysuckle extract, so they would not aggregate. Then, the cotton fabric was finished with Ag NPs' solution by the dipping method using a complex of polymaleic acid (PMA) and citric acid (CA) as a cross-linking agent to fix Ag NPs on the cotton fabric. The structures of cotton fabrics before and after finishing were characterized using FT-IR, scanning electron microscopy (SEM), XRD, X-ray photoelectron spectroscopy (XPS), and thermogravimetric (TG) analysis, and the multifunctional properties of the finished cotton fabrics were explored by measuring the antibacterial rate, the wrinkle recovery angle (WRA), and the UV protection factor (UPF) value. The results show that Ag NPs were successfully loaded onto cotton fabric, and the PMA + CA compound was successfully cross-linked to the fabric. The cross-linked Ag NPs' cotton fiber was rougher than that before cross-linking, and its TG stability improved. The PMA + CA compound fixed Ag NPs on the cotton fabric through chemical bonds, so it still had a 99% antibacterial effect against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) after 50 washings. Compared with unfinished cotton fabric, the UPF value and WRA of the cross-linked Ag NPs cotton increased by 34.09 and 98°, respectively, and its color did not change much.

Weavable Transparent Conductive Fibers with Harsh Environment Tolerance.

Fiber and textile electronics provide a focus for a new generation of wearable electronics due to their unique lightness and flexibility. However, fabricating knittable fibers from conductive materials with high tensile and transparent properties remains a challenge, especially for applicability in harsh environments. Here, we report a simple photopolymerization approach for the rapid preparation of a new type of a transparent conductive polymer fiber, poly(polymerizable deep eutectic solvent (PDES)) fiber, which exhibits excellent stability at high/low temperature, in organic solvents, especially in dry environments, and overcomes the volatility and freezability of traditional gel materials. A poly(PDES) fiber possesses outstanding mechanical and sensing properties, including negligible hysteresis and creep, fast resilience after a long stretch (10 min), and signal stability during high-frequency cyclic stretching (1 Hz, 10 000 cycles). In addition, the poly(PDES) fibers are knitted into a plain-structured sensor on textile with breathability and high tolerance to damage, enabling stable and accurate monitoring of human stretching, bending, and rotation motions. Furthermore, its dry-cleaning resistance guarantees the feasibility of long-term monitoring, with the electrical signal remaining stable after five dry-cleaning cycles. These promising features of poly(PDES) fibers will promote potential applications in the fields of human movement monitoring, intelligent fibers, and soft robotics.

E-Textile Systems Reliability Assessment-A Miniaturized Accelerometer Used to Investigate Damage during Their Washing.

E-textiles reveal a new and hybrid sector of the industry that is created by the integration of electronic components or textile-based electronics in our daily life textile products. They are facing problems in terms of washability, reliability, and user acceptance. This manuscript explains the mechanical stresses acting during the washing process and their impact on e-textile systems. Different washing programs were investigated in terms of total process duration. This washing process duration is mainly divided into three diverse washing actions: low-speed rotation, high-speed rotation, and stop time. This investigation was performed to highlight the importance of the washing actions and their percentages in the total washing process. A piece of fabric with a flexible PCB (printed circuit board), equipped with an accelerometer with a Bluetooth communication device and a microcontroller, was placed in the washing machine to analyze the movement of fabric provoked by washing stresses. The PCB was used for fabric movements recording to determine the impact of mechanical stress on e-textile systems during the washing process. From the video analysis, it was concluded that the duration of the low-speed and high-speed rotation actions should be privileged comparing to the duration of the whole washing process. A power spectral density (PSD) analysis based on the accelerometer outputs was realized. Mechanical stresses at different frequencies were identified. Based on this analysis, it could be possible to improve the protocols of mechanical tests (Martindale and pilling box) used to simulate the mechanical stress applied to e-textile systems during the washing process.

Monitoring Body Fluids in Textiles: Combining Impedance and Thermal Principles in a Printed, Wearable, and Washable Sensor.

This work explores the feasibility of coupling two different techniques, the impedance and the transient plane source (TPS) principle, to quantify the moisture content and its compositional parameters simultaneously. The sensor is realized directly on textiles with the use of printing and coating technology. Impedance measurements use the fluid's electrical properties, while the TPS measurements are based on the thermal effusivity of the liquid. Impedance and TPS measurements show equal competency in measuring the fluid volume with a lowest measurable quantity of 0.5 µL, enabling ultralow volume passive measurements for sweat analysis. Both sensor principles were tested by monitoring the drying of a wet cloth and the measurements show perfect repeatability and accuracy. Nevertheless, when the biofluid property changes, the TPS sensor does not reflect this information on its readings, whereas, on the other hand, impedance can provide information on compositional changes. However, since the volume of the fluid changes simultaneously, one cannot differentiate between a volume change and a compositional change from impedance measurements alone. Therefore, we show in this work that we can apply impedance to measure the compositional properties; meanwhile, the TPS measurements accurately carry out volume measurements irrespective of the interferences from its compositional variations. To prove this, both of these techniques are applied for the quantification and composition monitoring of sweat, showing the capability to measure moisture content and compositional parameters simultaneously. TPS measurements can also be an indicator of the local temperature of the medium confined by the sensor, and it does not influence the fluid parameters. Compiling both impedance and thermal sensors in a single platform triggers smart wearable prospects of metering the liquid volume and simultaneously analyzing other compositional changes and body temperature. Finally, the repeatability and stability of the sensor readings and the washability of the device are tested. This device could be a potential sensing tool in real-life applications, such as wound monitoring and sweat analysis, and could be a promising addition toward future smart wearable sensors.

Investigating the Impact of Washing Cycles on Silver-Plated Textile Electrodes: A Complete Study.

Although market prediction for smart textiles in the coming years is high, their washability will be among the main criteria for their mass adoption. Hence, the need to understand precisely how the washing process can damage them. Therefore, the best care instructions can be determined and serve as guidelines for smart textile manufacturers to control the quality of their smart garments as well as their customers to wash them cautiously. In this study, only the sensing part, silver-plated-nylon electrode sensors, is taken into account. To determine the chemical and the mechanical impacts of the machine-washing process separately and simultaneously, textile electrodes were put in different washing conditions: with and without bleaching agents, with and without mechanical constraints, etc. Then spectrophotometry, Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to characterize these electrodes. Results show that liquid detergents should be preferred to powder ones. Indeed, the latter contain bleaching agents that tend to oxidize the silver layer, making it more vulnerable to the mechanical rubbings that tear off the silver layer progressively washes after washes. As a consequence, the silver-plated-nylon loses rapidly its conductivity so that the electrode is no longer able to sense biopotentials.

Highly Wearable, Breathable, and Washable Sensing Textile for Human Motion and Pulse Monitoring.

At present, pressure sensor textiles are of great significance in the area of wearable electronics, especially for making smart or intelligent textiles. However, the design of these textile-based devices with sensitive ability, simple fabrication, and low cost is still challenging. In this study, we developed a triboelectric sensing textile constructed with core-shell yarns. Nylon filament and polytetrafluoroethylene filament were selected as the positive and negative layers, respectively, in the woven structure while the built-in helical stainless steel yarn was serving as the inner electrode layer. The sensitivity of the sensing textile can reach up to 1.33 V·kPa-1 and 0.32 V·kPa-1 in the pressure range of 1.95-3.13 kPa and 3.20-4.61 kPa, respectively. This sensing textile presented good mechanical stability and sensing capability even after 4200 cycles of continuous operation or after 4 h continuous water washing. Benefiting from the favorable merits of being highly flexible, breathable, lightweight, and even dyeable, the fabricated device was capable of being placed on any desired body parts for quantifying the dynamic human motions. It can be effectively used to measure and monitor various human movements associated with different joints, such as the hand, elbow, knee, and underarm. Moreover, the sensing textile was able to capture real-time pulse signals and reflect the current health status for human beings. This study affords an innovative and promising track for multifunctional pressure sensor textiles with wide applications in smart textiles and personalized healthcare.

Understanding the Washing Damage to Textile ECG Dry Skin Electrodes, Embroidered and Fabric-Based; set up of Equivalent Laboratory Tests.

Reliability and washability are major hurdles facing the e-textile industry nowadays. The main fear behind the product's rejection is the inability to ensure its projected life span. The durability of e-textiles is based on an approximate lifetime of both the electronics and textiles integrated into the product. A detailed analysis of the wash process and the possibility of predicting product behavior are key factors for new standards implementation. This manuscript is focused on the washability issues of different types of woven, knitted, and embroidered, textile-based ECG electrodes. These electrodes are used without the addition of any ionic gel to the skin to reduce impedance. They were subjected to up to 50 wash cycles with two different types of wash processes, and changes in surface resistance, as well as the quality of ECG waves, were observed To investigate the wash damages in detail, the proposed mechanical (Martindale and Pilling box) and chemical test methods were investigated. The electrodes which increased resistance after washing showed the same trend in the proposed test methods. Copper-based electrodes suffered the most severe damage and increased resistance, as was also visible in an SEM analysis. These proposed test methods can be used to predict robustness behavior without washing.

Stretchable Conductive Adhesives with Superior Electrical Stability as Printable Interconnects in Washable Textile Electronics.

As practical interest in stretchable electronics increases for future applications in wearables, healthcare, and robotics, the demand for electrical interconnects with high electrical conductivity, durability, printability, and adhesion is growing. Despite the high electrical conductivity and stretchability of most previous interconnects, they lack stable conductivity against strain and adhesion to stretchable substrates, leading to a limitation for their practical applications. Herein, we propose a stretchable conductive adhesive consisting of silver particles with carbon nanotube as an auxiliary filler in silicone adhesives. The conductive adhesive exhibits a high initial conductivity of 6450 S cm-1. They show little change in conductivity over 3000 stretching cycles at 50% strain, currently the highest stability reported for elastic conductors. Based on strong adhesion to stretchable substrates, the gel-free, dry adhesives printed on an elastic bandage for electrocardiography monitoring exhibit an extremely stable performance upon movement of the subject, even after several cycles of detachment-reattachment and machine washing.

High-Quality Images Inkjetted on Different Woven Cotton Fabrics Cationized with P(St-BA-VBT) Copolymer Nanospheres.

The porosity, roughness, and thickness of woven fabrics limit inkjet printing quality, which is extremely important for obtaining high-quality inkjet printing images on fabrics. This study reveals the application of poly[styrene-butyl acrylate-(P-vinylbenzyl trimethyl ammonium chloride)] nanospheres prepared via a soap-free emulsion polymerization approach as a novel kind of the cationization modifier for the inkjet printing of different woven cotton fabrics by the pad-cure process. It was found that the nanospheres exhibited an average diameter of 65.5 nm, a zeta potential of +57.8 mV, and a glass transition temperature of 94.7 °C. The nanospheres deposited on three cotton fabrics through the dip-rolling process, resulting in the increase of zeta potential, hydrophobicity and thickness of the fabric, and the decrease of porosity and roughness. The high-quality inkjet printing images can be obtained on fabrics with different structures owing to the differences in zeta potential, hydrophobicity, porosity, roughness, and thickness of fabrics. The plain, twill, and honeycomb weave fabrics obtained high-quality inkjet printing images for portraits, oil paintings, and landscape paintings, respectively. The nanospheres could strongly adsorb on the fiber by electrostatic attraction. The reactive dye molecules in the inks could react with the cationized fibers by electrostatic attractive force, resulting in the increase of the color strength, fixation rates, and outline sharpness. The nanosphere cationization of different woven fabrics offers a new potential method for obtaining high-quality patterns without significantly affecting the fabric handle.

Development of a Mucoadhesive and In Situ Gelling Formulation Based on κ-Carrageenan for Application on Oral Mucosa and Esophagus Walls. I. A Functional In Vitro Characterization.

Oral mucositis and esophagitis represent the most frequent and clinically significant complications of cytoreductive chemotherapy and radiotherapy, which severely compromise the patient quality of life. The local application of polymeric gels could protect the injured tissues, alleviating the most painful symptoms. The present work aims at developing in situ gelling formulations for the treatment of oral mucositis and esophagitis. To reach these targets, κ-carrageenan (κ-CG) was selected as a polymer having wound healing properties and able to gelify in the presence of saliva ions, while hydroxypropyl cellulose (HPC) was used to improve the mucoadhesive properties of the formulations. CaCl2 was identified as a salt able to enhance the interaction between κ-CG and saliva ions. Different salt and polymer concentrations were investigated in order to obtain a formulation having the following features: (i) low viscosity at room temperature to facilitate administration, (ii) marked elastic properties at 37 °C, functional to a protective action towards damaged tissues, and (iii) mucoadhesive properties. Prototypes characterized by different κ-CG, HPC, and CaCl2 concentrations were subjected to a thorough rheological characterization and to in vitro mucoadhesion and washability tests. The overall results pointed out the ability of the developed formulations to produce a gel able to interact with saliva ions and to adhere to the biological substrates.

Inkjet Printing of Reactive Silver Ink on Textiles.

Inkjet printing of functional inks on textiles to embed passive electronics devices and sensors is a novel approach in the space of wearable electronic textiles. However, achieving functionality such as conductivity by inkjet printing on textiles is challenged by the porosity and surface roughness of textiles. Nanoparticle-based conductive inks frequently cause blockage/clogging of inkjet printer nozzles, making it a less than ideal method for applying these functional materials. It is also very challenging to create a conformal conductive coating and achieve electrically conductive percolation with the inkjet printing of metal nanoparticle inks on rough and porous textile and paper substrates. Herein, a novel reliable and conformal inkjet printing process is demonstrated for printing particle-free reactive silver ink on uncoated polyester textile knit, woven, and nonwoven fabrics. The particle-free functional ink can conformally coat individual fibers to create a conductive network within the textile structure without changing the feel, texture, durability, and mechanical behavior of the textile. It was found that the conductivity and the resolution of the inkjet-printed tracks are directly related with the packing and the tightness of fabric structures and fiber sizes of the fabrics. It is noteworthy that the electrical conductivity of the inkjet-printed conductive coating on pristine polyethylene terephthalate fibers is improved by an order of magnitude by in situ heat-curing of the textile surface during printing as the in situ heat-curing process minimizes the wicking of the ink into the textile structures. A minimum sheet resistance of 0.2 ± 0.025 and 0.9 ± 0.02 Ω/□ on polyester woven and polyester knit fabrics is achieved, respectively. These findings aim to advance E-textile product design through integration of inkjet printing as a low-cost, scalable, and automated manufacturing process.

Ambulatory Evaluation of ECG Signals Obtained Using Washable Textile-Based Electrodes Made with Chemically Modified PEDOT:PSS.

A development of washable PEDOT:PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate) polyamide textile-based electrodes is an interesting alternative to the traditional Ag/AgCl disposable electrodes, usually used in clinical practice, helping to improve medical assessment and treatment before apparition or progress of patients' cardiovascular symptoms. This study was conducted in order to determine whether physical properties of PEDOT:PSS had a significant impact on the coated electrode's electrocardiogram (ECG) signal quality, particularly after 50 washing cycles in a domestic laundry machine. Tests performed, included the comparison of two PEDOT:PSS solutions, in term of viscosity with emphasis on wetting tests, including surface tension and contact angle measurements. In addition, polyamide textile fabrics were used as substrate to make thirty electrodes and to characterize the amount of PEDOT:PSS absorbed as a function of time. The results showed that surface tension of PEDOT:PSS had a significant impact on the wetting of polyamide textile fabric and consequently on the absorbed amount. In fact, lower values of surface tension of the solution lead to low values contact angles between PEDOT:PSS and textile fabric (good wettability). Before washing, no significant difference has been observed among signal-to-noise ratios measured (SNR) for coated electrodes by the two PEDOT:PSS solutions. However, after 50 washing cycles, SNR decreased strongly for electrodes coated by the solution that had low viscosity, since it contained less solid contents. That was confirmed by scanning electron microscopy images (SEM) and also by analyzing the color change of electrodes based on the calculation of CIELAB color space coordinates. Moreover, spectral power density of recorded ECG signals has been computed and presented. All cardiac waves were still visible in the ECG signals after 50 washing cycles. Furthermore, an experienced cardiologist considered that all the ECG signals acquired were acceptable. Accordingly, our newly developed polyamide textile-based electrodes seem to be suitable for long-term monitoring. The study also provided new insights into the better choice of PEDOT:PSS formulation as a function of a specific process in order to manufacture cheaper electrodes faster.

Comparative Study on Conductive Knitted Fabric Electrodes for Long-Term Electrocardiography Monitoring: Silver-Plated and PEDOT:PSS Coated Fabrics.

Long-term monitoring of the electrical activity of the heart helps to detect the presence of potential dysfunctions, enabling the diagnosis of a wide range of cardiac pathologies. However, standard electrodes used for electrocardiogram (ECG) acquisition are not fully integrated into garments, and generally need to be used with a gel to improve contact resistance. This article is focused on the development of washable screen-printed cotton, with and without Lycra, textile electrodes providing a medical quality ECG signal to be used for long-term electrocardiography measurements. Several samples with different Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) concentrations were investigated. Silver-plated knitted fabric electrodes were also used for comparison, within the same process of ECG signal recording. The acquisition of ECG signals carried out by a portable medical device and a low-coast Arduino-based device on one female subject in a sitting position. Three textile electrodes were placed on the right and left forearms and a ground electrode was placed on the right ankle of a healthy female subject. Plastic clamps were applied to maintain electrodes on the skin. The results obtained with PEDOT:PSS used for electrodes fabrication have been presented, considering the optimal concentration required for medical ECG quality and capacity to sustain up to 50 washing cycles. All the ECG signals acquired and recorded, using PEDOT:PSS and silver-plated electrodes, have been reviewed by a cardiologist in order to validate their quality required for accurate diagnosis.