Spatial distribution and health risks assessment of heavy metals in e-waste dumping sites from Pakistan.

The present study focused on to determine the concentration and health risk of heavy metals (Cu, Pb, Zn, Cd, Hg, Cr) in e-waste contaminated soils collected from different provinces of Pakistan. Further, the impact of heavy metals on soil enzyme activities and microbial community was also investigated. The concentration (mg/kg) of Hg, Zn, Fe, Cu, Pb, Cd, and Cr ranged between 0-0.258, 2.284-6.587, 3.005-40.72, 8.67-36.88, 12.05-35.03, 1.03-2.43, and 33.13-60.05, respectively. The results revealed that Lahore site of Punjab province indicated more concentration of heavy metals as compared to other sites. The level of Cr at all sites whereas Hg at only two sites exceeds the World Health Organization standards (WHO) for soil. Soil enzyme activity exhibited dynamic trend among the sites. Maximum enzyme activity was observed for urease followed by phosphatase and catalase. Contamination factor (Cf), Pollution load index (PLI), and geo-accumulation index (Igeo) results showed that all the sites are highly contaminated with Cu, Cd, and Pb. Hazard index (HI) was less than 1 for children and adults suggesting non-carcinogenic health risk. Principle component analysis results depicted relation among Cr, Fr, catalase, and actinomycetes; Cd, OM, urease, and bacteria, and Pb, Cu, Zn, Hg, and phosphatase, suggesting soil enzymes and microbial community profiles were influenced by e-waste pollution. Therefore, there is a dire need to introduce sustainable e-waste recycling techniques as well as to make stringent e-waste management policies to reduce further environmental contamination.

Application of soil magnetometry and geochemical methods to investigate soil contamination with antimony.

The aim of the study was an assessment of the pollution level and identification of the antimony sources in soils in areas subjected to industrial anthropopressure from: transport, metallurgy and electrical waste recycling. The combination of soil magnetometry, chemical analyzes using atomic spectrometry (ICP-OES and ICP-MS), Sb fractionation analysis, statistical analysis (Pearson's correlation matrix, factor analysis) as well as Geoaccumulation Index, Pollution Load Index, and Sb/As factor allowed not only the assessment of soil contamination degree, but also comprehensive identification of different Sb sources. The results indicate that the soil in the vicinity of the studied objects was characterized by high values of magnetic susceptibility and thus, high contents of potentially toxic elements. The most polluted area was in the vicinity of electrical waste processing plants. Research has shown that the impact of road traffic and wearing off brake blocks, i.e. traffic anthropopression in general, has little effect on the surrounding soil in terms of antimony content. Large amounts of Pb, Zn, As and Cd were found in the soil collected in the vicinity of the heap after the processing of zinc-lead ores, the average antimony (11.31 mg kg-1) content was lower in the vicinity of the heap than in the area around the electrical and electronic waste processing plant, but still very high. Antimony in the studied soils was demobilized and associated mainly with the residual fraction.

Leaching of liquation-feeding furnace dross as a first step for germanium recovery.

OBJECTIVE: Germanium, an important component of electronics, is considered by many global economies as a critical raw material. Therefore, investigating its potential new sources is crucial for prospective technology development. This paper presents the investigation results on the leaching of liquation-feeding furnace dross using sulfuric and oxalic acid solutions. RESULTS: The dross contained mostly zinc (68.0% wt.) but also elevated germanium concentration (0.68% wt.). The influence of temperature, time, initial acid concentration, and liquid-to-solid phase ratio (L:S) was examined. It was found that germanium availability via leaching is limited-maximum leaching yields using aqueous solutions of sulfuric and oxalic acids were 60% (80 °C, 2 h, 15% wt. H2SO4, L:S 25:1) and 57% (80 °C, 3 h, 12.5% wt. H2C2O4, L:S 10:1), respectively.

Anaerobic biodegradation enables zero liquid discharge of two-stage nanofiltration system for microelectronic wastewater treatment.

Nanofiltration (NF) is a promising technology in the treatment of microelectronic wastewater. However, the treatment of concentrate derived from NF system remains a substantial technical challenge, impeding the achievement of the zero liquid discharge (ZLD) goal in microelectronic wastewater industries. Herein, a ZLD system, coupling a two-stage NF technology with anaerobic biotechnology was proposed for the treatment of tetramethylammonium hydroxide (TMAH)-contained microelectronic wastewater. The two-stage NF system exhibited favorable efficacy in the removal of conductivity (96 %), total organic carbon (TOC, 90 %), and TMAH (96 %) from microelectronic wastewater. The membrane fouling of this system was dominated by organic fouling, with the second stage NF membrane experiencing a more serious fouling compared to the first stage membrane. The anaerobic biotechnology achieved a near-complete removal of TMAH and an 80 % reduction in TOC for the first stage NF concentrate. Methyloversatilis was the key genus involved in the anaerobic treatment of the microelectronic wastewater concentrate. Specific genes, including dmd-tmd, mtbA, mttB and mttC were identified as significant players in mediating the dehydrogenase and methyl transfer pathways during the process of TMAH biodegradation. This study highlights the potential of anaerobic biodegradation to achieve ZLD in the treatment of TMAH-contained microelectronic wastewater by NF system.

Alterations of gut microbiota and its metabolomics in children with 6PPDQ, PBDE, PCB, and metal(loid) exposure.

The composition and metabolites of the gut microbiota can be altered by environmental pollutants. However, the effect of co-exposure to multiple pollutants on the human gut microbiota has not been sufficiently studied. In this study, gut microorganisms and their metabolites were compared between 33 children from Guiyu, an e-waste dismantling and recycling area, and 34 children from Haojiang, a healthy environment. The exposure level was assessed by estimating the daily intake (EDI) of polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyls (PCBs), 6PPD-quinone (6PPDQ), and metal(loid)s in kindergarten dust. Significant correlations were found between the EDIs of 6PPDQ, BDE28, PCB52, Ni, Cu, and the composition of gut microbiota and specific metabolites. The Bayesian kernel machine regression model showed negative correlations between the EDIs of five pollutants (6PPDQ, BDE28, PCB52, Ni, and Cu) and the composition of gut microbiota. The EDIs of these five pollutants were positively correlated with the levels of the metabolite 2,4-diaminobutyric acid, while negatively correlated with the levels of d-erythro-sphingosine and d-threitol. Our study suggests that exposure to 6PPDQ, BDE28, PCB52, Ni, and Cu in kindergarten dust is associated with alterations in the composition and metabolites of the gut microbiota. These alterations may be associated with children's health.

Pyrolytic urban mining of waste printed circuit boards: an enviro-economic analysis.

E-waste, a global environmental concern resulting from supply chain inefficiency, also offers the opportunity to recover valuable materials, including general and rare earth metals. Waste printed circuit boards (WPCBs) are integral components of e-waste that contains substantial amounts of precious metals, making them a valuable waste category. Pyrolysis has emerged as a promising method for material recovery from WPCBs. Hence, pyrolytic urban mining of WPCBs offers an excellent avenue for resource recovery, redirecting valuable materials back into the supply chain. Under the current study, experimental investigation has been conducted to explore the recovery of materials from WPCBs through pyrolysis followed by process simulation, economic analysis, and life cycle assessment (LCA). An Aspen Plus simulation was conducted to model the pyrolysis of WPCBs and subsequent product recovery using a non-equilibrium kinetic model, which represents a unique approach in this study. Another distinct aspect is the comprehensive assessment of environmental and economic sustainability. The economic analysis has been carried out using Aspen economic analyzer whereas the LCA of WPCB pyrolysis has been conducted using the SimaPro software. The experimental investigation reveals yield of solid residues are about 75-84 wt.%, liquid yields of 6-13 wt.%, and gas yields of 4-21 wt.%, which is in well agreement with the Aspen Plus simulation results. The economic analysis for an e-waste pyrolysis plant with an annual feed rate of 2000 t reveals that the total capital cost of a pyrolysis plant is nearly $51.3 million, whereas the total equipment cost is nearly $2.7 million and the total operating cost is nearly $25.6 million. The desired rate of return is 20% per year and the payback period is 6 years with a profitability index of 1.25. From the LCA, the major impact categories are global warming, fossil resource scarcity, ozone formation in human health, ozone formation in terrestrial ecosystems, fine particulate matter formation, and water consumption. The findings of this study can serve as a guideline for e-waste recyclers, researchers, and decision-makers in establishing circular economy.

Contamination characteristics and dietary intake risk of brominated flame retardants in fishes around a typical e-waste dismantling site in Southern China.

Polybrominated diphenyl ethers (PBDEs) and their substitutes, novel brominated flame retardants (NBFRs), are ubiquitously present in the aquatic environment of electronic waste (e-waste) dismantling region, leading to their inevitable absorption and accumulation by aquatic organisms, which can be transferred to human via directly aquatic product consumption or through food chain, thereby posing potential health risks. This study focused on fish samples from Guiyu and its surrounding areas, and found the total PBDEs concentrations were 24-7400 ng/g lw (mean: 1800 ng/g lw) and the total NBFRs concentrations were 14 to 2300 ng/g lw (mean: 310 ng/g lw). Significant positive correlations were found among PBDE congeners, among different NBFRs, and between NBFRs and commercial PBDEs that they replace. ΣPBDEs and ΣNBFRs in the intestine were 620-350,000 and 91-81,000 ng/g lw (mean: 83000 and 12,000 ng/g lw, respectively), significantly exceeding those in the gills, where ΣPBDEs and ΣNBFRs were 14-37,000 and 39-45,000 ng/g lw (mean: 9200 and 2400 ng/g lw, respectively). The ΣPBDEs and ΣNBFRs showed no non-carcinogenic risks to the target population through dietary intake. Despite the significantly higher daily intake of decabromodiphenyl ethane (DBDPE) compared to decabromodiphenyl ether (BDE209), the non-carcinogenic risk associated with BDE209 remained higher than that of DBDPE. Our findings can assist researchers in understanding the presence of BFRs in aquatic organisms, inhabiting e-waste dismantling areas, and in evaluating the associated health risks posed to humans through dietary exposure.

A biogenic hydrogel to recover Au(III) from electronic waste.

In the course of this investigation, we undertook the contemplation of a green chemistry paradigm with the express intent of procuring valuable metal, namely gold, from electronic waste (e-waste). In pursuit of this overarching objective, we conceived a procedural framework consisting of two pivotal stages. As an initial stage, we introduced a physical separation procedure relying on the utilization of the Eddy current separator, prior to embarking on the process of leaching from e-waste. Subsequent to the partitioning of metals from the non-metal constituents of waste printed circuit boards (PCB), we initiated an investigation into the hydrogel derived from basil seeds (Ocimum basilicum L.), utilizing it as a biogenic sorbent medium. The thorough characterization of hydrogel extracted from basil seeds involved the application of an array of analytical techniques, encompassing FTIR, XRD, SEM, and BET. The batch sorption experiments show more than 90% uptake in the pH range of 2-5. The sorption capacity of the hydrogel material was evaluated as 188.44 mg g-1 from the Langmuir Isotherm model. The potential interference stemming from a spectrum of other ions, encompassing Al, Cu, Ni, Zn, Co, Cr, Fe, Mn, and Pb was systematically examined. Notably, the sole instance of interference in the context of adsorption of gold ions was observed to be associated with the presence of lead. The application of the hydrogel demonstrated a commendable efficiency in the recovery of Au(III) from the leached solution derived from the waste PCB.

Development of complete hydrometallurgical processes for gold recovery from ICs and CPUs using ionic liquids.

Integrated circuits (ICs) and central processing units (CPUs), essential components of electrical and electronic equipment (EEE), are complex composite materials rich in recyclable high-value strategic and critical metals, with many in concentrations higher than in their natural ores. With gold the most valuable metal present, increase in demand for gold for EEE and its limited availability have led to a steep rise in the market price of gold, making gold recycling a high priority to meet demand. To overcome the limitations associated with conventional technologies for recycling e-waste, the use of greener technologies (ionic liquids (ILs) as leaching agents), offers greater potential for the recovery of gold from e-waste components. While previous studies have demonstrated the efficiency and feasibility of using ILs for gold recovery, these works predominantly concentrate on the extraction stage and often utilise simulated solutions, lacking the implementation of a complete process validated with real samples to effectively assess its overall effectiveness. In this work, a simulated Model Test System was used to determine the optimal leaching and extraction conditions before application to real samples. With copper being the most abundant metal in the e-waste fractions, to access the gold necessitated a two-stage pre-treatment (nitric acid leaching followed by aqua regia leaching) to ensure complete removal of copper and deliver a gold-enriched leach liquor. Gold extraction from the leach liquor was achieved by liquid-liquid extraction using Cyphos 101 (0.1 M in toluene with an O:A = 1:1, 20 °C, 150 rpm, and 15 min) and as a second process by sorption extraction with loaded resins (Amberlite XAD-7 with 300 mg of Cyphos 101/g of resins at 20 °C, 150 rpm and 3 h). In both processes, complete stripping and desorption of gold was achieved (0.5 M thiourea in 0.5 M HCl) and gold recovered, as nanoparticles of purity ≥95%, via a reduction step using a sodium borohydride solution (0.1 M NaBH4 in 0.1 M NaOH). These two hydrometallurgical processes developed can achieve overall efficiencies of ≥95% for gold recovery from real e-waste components, permit the reuse of the IL and resins up to five consecutive times, and offer a promising approach for recovery from any e-waste stream rich in gold.

Persistent organic pollutants in feathers of various terrestrial and aquatic bird species: Interspecies difference and source apportionment.

Feathers are regarded as important nondestructive biomonitoring tools for bird pollutants. However, external contamination of feathers by different pollutants in different bird species remains unclear. In the present study, the feathers of 16 bird species, including terrestrial, freshwater, and marine birds, were analyzed for persistent organic pollutants (POPs). Bird feathers from an abandoned e-waste recycling site had higher POP concentrations and were more correlated with the POP muscle concentrations than those from the less polluted areas. The significant and positive POP correlations between the feathers and muscles of different species indicate that feathers are a good indicator of inter-species and spatial pollution. For individual species, the most hydrophobic POPs in feathers, such as hepta- to deca-polybrominated diphenyl ethers, had higher proportions than in muscles and worse correlations with muscle POPs compared with other POPs. Results of the chemical mass balance (CMB) model revealed that the gaseous phase, internal pollution, and atmospheric particle phase were the main contributors to low-, medium-, and high-hydrophobicity POPs in feathers, respectively. Overall, this study provides a preliminary but meaningful framework for distinguishing between internal and external contamination in feathers and gives information concerning the fitness of feathers as POP indicators with specific physicochemical properties.

Copper recovery by solvent extraction for nanoparticle synthesis from waste motherboards.

Printed circuit boards, which make up part of waste from electrical and electronic equipment, contain elements that can be economically reused, such as copper, silver, gold, and nickel, as well as metals that are harmful to the environment and health, such as lead, mercury, and cadmium. Thus, through recycling this scrap, materials that would otherwise be discarded can be reinserted as secondary raw materials to produce new consumer goods through urban mining. In this context, the synthesis of nanoparticles shows promise as it allows the reinsertion of these materials in the manufacture of new products. Therefore, this study used obsolete computer motherboards as a secondary material to obtain copper to produce nanoparticles of this metal. From a solution based on the leach liquor of this scrap, a purification route using solvent extraction was defined and applied to the real leach liquor. Applying the hydroxyoxime extractant at a dilution of 20% (v/v) in kerosene, A/O of 1/1, 298 K, and 0.25 h of contact during extraction, and stripping in H2SO4 (2 M), 298 K, 0.25 h, W/O ratio of 3/1, and two theoretical countercurrent stages, a solution containing more than 95% of the copper in the leach liquor could be obtained with less than 1% of contaminants. From this purified liquor, nanoparticles containing copper and metallic copper oxides and hydroxides were produced, with an average size of 84 nm, at pH 11, 3 h of hot stirring, volume of 0.015 L of ascorbic acid (0.50 M) and 0.015 L of precursor solution (0.03 M Cu), and temperature (343 K).

A raising alarm on the current global electronic waste situation through bibliometric analysis, life cycle, and techno-economic assessment: a review.

Electronic waste (E-waste) production worldwide is increasing three times faster than the growth of the global population, and it is predicted that the total volume of E-waste will reach 74 million tonnes by 2030. United Nations warned that unless emissions of heat-trapping gases are drastically reduced, humanity will face catastrophic climate change. We created a bibliometric analysis and discussed the life cycle and techno-economic assessments of the current E-waste situation. We found trending E-waste topics, particularly those related to industrial facilities implementing a circular economy framework and improving the recycling methods of lithium-ion batteries, and this was linked to the topic of electric vehicles. Other research themes included bioleaching, hydrometallurgy, reverse logistics, heavy metal life cycle assessment, and sustainability. These topics can interest industrial factories and scientists interested in these fields. Also, throughout techno-economic assessments, we highlighted several economic and investment opportunities to benefit stakeholders from E-waste recycling. While the rate of E-waste is increasing, consumer education on the proper E-waste management strategies, a collaboration between international organizations with the industrial sector, and legislation of robust E-waste regulations may reduce the harmful effect on humans and the environment and increase the income to flourish national economies.

Informal E -waste recycling in nine cities of Pakistan reveals significant impacts on local air and soil quality and associated health risks.

The global increase in electronic waste (e-waste) has led to a rise in informal recycling, emitting hazardous heavy metals (HMs) that threaten human health and ecosystems. This study presents the first comprehensive assessment of HM levels in dry deposition and soils at proximity of forty (40) informal e-waste recycling sites across Pakistan, between September 2020 to December 2021. Findings reveal that Zn (1410), Pb (410) and Mn (231) exhibited the higher mean deposition fluxes (µg/m2.day), derived from air samples, particularly in Karachi. Similarly, soils showed higher mean concentrations (µg/g dw) of Mn (477), Cu (514) and Pb (172) in Faisalabad, Lahore, and Karachi, respectively. HMs concentrations were found higher in winter or autumn and lower in summer. In addition, HM levels were significantly (p = 0.05) higher at recycling sites compared to background sites year-round, highlighting the e-waste recycling operations as the major source of their emissions. The Igeo index indicated moderate to extremely contaminated levels of Cu, Pb, Cd, and Ni in Karachi, Lahore and Gujranwala. Ingestion was found as a leading human exposure route, followed by dermal and inhalation exposure, with Pb posing the greatest health risk. The Cumulative Incremental Lifetime Cancer Risk (ILCR) model suggested moderate to low cancer risks for workers. Strategic interventions recommend mitigating health and environmental risks, prioritizing human health and ecosystem integrity in Pakistan's e-waste management.

Inventory and management of E-waste: a case study of Kerala, India.

The recent surge in electronic device usage has led to a notable rise in electronic waste (E-waste) generation, presenting significant environmental challenges. This study aims to quantify Kerala's E-waste inventory and formulate a comprehensive management plan. Utilizing sales data from 2017 to 2020 and estimating E-waste generation based on "average" or "end-of-life" durations of electrical and electronic equipment (EEE) items, the analysis forecasts substantial E-waste quantities. Key assumptions include correlating sales data with E-waste generation and utilizing guidelines for estimating E-waste quantities based on EEE item types and sales figures. The highest E-waste generation is predicted for the years 2028-2029, estimated at 97,541 tonnes, which is crucial for the state's management strategy. To address this challenge, the study proposes a comprehensive environmental management plan that integrates the principles of reduce, reuse, and recycle (3R) into its core strategies. The plan includes establishing 78 collection units across the state, strategically allocated based on the Taluk (a sub-division of a district) population, to ensure efficient E-waste collection and recovery of reusable items. Additionally, the study outlines the need for 273 recycling units statewide, with Malappuram district requiring the most units due to its high population density. The plan emphasizes efficient E-waste collection, segregation, and recycling, promoting responsible consumption and resource conservation. The study furnishes a "cradle-to-grave" framework for the management of E-waste at local, regional, and national levels, serving as a valuable resource for pollution control boards, regulatory bodies, statutory bodies, and research organizations alike.

Estimated daily intake and cumulative risk assessment of organophosphate esters and associations with DNA damage among e-waste workers in Hong Kong.

Organophosphate esters (OPEs) are extensively used as additives in various products, including electronic equipment, which becomes e-waste when obsolete. Nevertheless, no study has evaluated OPEs exposure levels and the related health risks among e-waste workers in Hong Kong. Therefore, 201 first-spot morning urine samples were collected from 101 e-waste workers and 100 office workers to compare eight urinary OPE metabolites (mOPEs) levels in these groups. The concentrations of six mOPEs were similar in e-waste workers and office workers, except for significantly higher levels of diphenyl phosphate (DPHP) in e-waste workers and bis(1-chloro-2propyl) phosphate (BCIPP) in office workers. Spearman correlation analysis showed that most non-chlorinated mOPEs were correlated with each other in e-waste workers (i.e., nine out of ten pairs, including di-p-cresyl phosphate (DpCP) and di-o-cresyl phosphate (DoCP), DpCP and bis(2-butoxyethyl) phosphate (BBOEP), DpCP and DPHP, DpCP and dibutyl phosphate (DBP), DoCP and BBOEP, DoCP and DPHP, DoCP and DBP, BBOEP and DPHP, DPHP and DBP), indicating that handling e-waste could be the exposure source of specific OPEs. The median values of estimated daily intake (EDI) and hazard quotient (HQ) suggested that the health risks from OPEs exposures were under the recommended thresholds. However, linear regression models, Quantile g-computation, and Bayesian kernel machine regression found that urinary mOPEs elevated 8-hydroxy-2-deoxyguanosine (8-OhdG) levels individually or as a mixture, in which DPHP contributed prominently. In conclusion, although e-waste might not elevate the internal OPEs levels among the participating Hong Kong e-waste workers, attention should be paid to the potential DNA damage stimulated by OPEs under the currently recommended thresholds.

An alternative classification approach for waste electronic and electrical equipment (WEEE) recovery in low-income countries: case study in Burkina Faso.

Waste electrical and electronic equipment (WEEE) is defined as "urban mines" due to the various recoverable minerals they contain. However, current WEEE classification methods are mostly limited to their physical characteristics, focusing on collection, transport, and treatment purposes rather than on valorization. In the present study, our aim is to propose an alternative classification approach adapted for low-income countries for WEEE recovery that highlights their content of precious and valuable metals. A typology of WEEE was created based on WEEE generated in Ouagadougou (Burkina Faso). Principal component analysis (PCA) and the moving center technique (K-means) were used for the classification method. Ultimately, we have found that to improve the recovery of WEEE, they can be classified into three main groups: (i) a group of WEEE-containing batteries, (ii) a group of WEEE-containing valuable and precious metals, and finally, (iii) a group of WEEE made up of cathode ray tube televisions (CRT-TV) waste. The WEEE belonging to the second group are the ones that could generate higher economical values. This alternative classification approach will help investors and operators to better orient their valorization activities towards WEEE types that present the best precious metals recovery potential, maximizing their profits. On the other hand, decision-makers will find this classification useful for reorganizing the WEEE value chain.

Biodegradation of e-waste microplastics by Penicillium brevicompactum.

Electronic and electric waste (e-waste) management strategies often fall short in dealing with the plastic constituents of printed circuit boards (PCB). Some plastic materials from PCB, such as epoxy resins, may release contaminants, but neither potential environmental impact has been assessed nor mitigation strategies have been put forward. This study assessed the biodegradation of microplastics (1-2 mm in size) from PCB by the fungus Penicillium brevicompactum over 28 days, thus contributing to the discussion of mitigation strategies for decreasing the environmental impact of such plastics in the environment. The capacity of P. brevicompactum to induce microplastic fragmentation and degradation has been determined by the increased the number of smaller-sized particles and microplastic mass reduction (up to 75 % within 14 days), respectively. The occurrence of chain scission and oxidation of microplastics exposed to P. brevicompactum when compared with the control conditions (which occurred only after 28 days of exposure) can be observed. Furthermore, Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) spectroscopy performed in dried biomass put in evidence an increase in the absorption intensities in regions that could be attributed to functional groups associated with carbohydrates. The results underline the potential role of the genus Penicillium, particularly P. brevicompactum, in the biodegradation of microplastics from PCB, thus providing the basis for further exploration of its potential for e-waste bioremediation and research on the underlying mechanisms for sustainable approaches to mitigate e-waste pollution.

Hormonal, liver, and renal function associated with electronic waste (e-waste) exposure in Dhaka, Bangladesh.

Electronic waste (e-waste) contains numerous metals and organic pollutants that have detrimental impacts on human health. We studied 199 e-waste recycling workers and 104 non-exposed workers; analyzed blood, urine, and hair samples to measure heavy metals, hormonal, liver, and renal function. We used quantile regression models to evaluate the impact of Pb, Cd, and Hg on hormonal, liver and renal function, and the role of DNA oxidative damage in mediating the relationship between exposures and outcomes. Exposed workers had higher blood lead (Pb) (median 11.89 vs 3.63 µg/dL), similar blood cadmium (Cd) (1.04 vs 0.99 µg/L) and lower total mercury (Hg) in hair (0.38 vs 0.57 ppm) than non-exposed group. Exposed workers also had elevated median concentrations of total triiodothyronine (TT3), aspartate aminotransferase (AST), alanine aminotransferase (ALT), urinary albumin, albumin creatinine ratio (ACR) and estimated glomerular filtration rate (eGFR) were significantly higher than non-exposed group (p≤0.05). Sex hormones including luteinizing hormone, follicle stimulating hormone, estrogen, progesterone and testosterone concentrations were not significantly different between exposed and non-exposed (all p≥0.05). The median concentration of ALT was 4.00 (95% CI: 0.23, 7.77), urinary albumin was 0.09 (95% CI: 0.06, 0.12) and ACR was 1.31 (95% CI: 0.57, 2.05) units higher in the exposed group compared to non-exposed group. Pb was associated with a 3.67 unit increase in the ALP (95% CI: 1.53, 5.80), 0.01 unit increase in urinary albumin (95% CI: 0.002, 0.01), and 0.07 unit increase in ACR (95% CI: 0.01, 0.13). However, no hormonal, renal, and hepatic parameters were associated with Cd or Hg. Oxidative DNA damage did not mediate exposure-outcome relationships (p≥0.05). Our data indicate e-waste exposure impairs liver and renal functions secondary to elevated Pb levels. Continuous monitoring, longitudinal studies to evaluate the dose-response relationship and effective control measure are required to protect workers from e-waste exposure.

Influences of plasma treatment parameters on the hydrophobicity of cathode and anode materials from spent lithium-ion batteries.

The recycling of spent lithium-ion batteries (LIBs) can not only reduce the potential harm caused by solid waste piles to the local environment but also provide raw materials for manufacturing new batteries. Flotation is an alternative approach to achieve the selective separation of cathode and anode active materials from spent LIBs. However, the presence of organic binder on the surface of hydrophilic lithium transition-metal oxides results in losses of cathode materials in the froth phase. In this study, plasma treatment was utilized to remove organic layers from cathode and anode active materials. Firstly, the correlations between plasma treatment parameters (e.g., input power, air flowrate, and treatment time) were explored and the contact angles of cathode and anode active materials were investigated by the response surface methodology. Secondly, differences in the flotation recoveries of cathode and anode active materials were enhanced with plasma modification prior to flotation, which is consistent with the contact angle measurement. Finally, the plasma-modification mechanisms of hydrophobicity of cathode and anode active materials were discussed according to Fourier Transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses. The proposed method could be a promising tool to enhance the flotation separation efficiency of cathode and anode active materials for the recycling of spent LIBs.

Informal E-waste dismantling activities accelerated the releasing of liquid crystal monomers (LCMs) in Pakistan: Occurrence, distribution, and exposure assessment.

Liquid crystal monomers (LCMs) are emerging contaminants characterized by their persistence, bioaccumulation potential, and toxicity. They have been observed in several environmental matrices associated with electronic waste (e-waste) dismantling activities, particularly in China. However, there is currently no information on the pollution caused by LCMs in other developing countries, such as Pakistan. In this study, we collected soil samples (n = 59) from e-waste dismantling areas with different functions in Pakistan for quantification analysis of 52 target LCMs. Thirty out of 52 LCMs were detected in the soil samples, with the concentrations ranging from 2.14 to 191 ng/g (median: 16.3 ng/g), suggesting widespread contamination by these emerging contaminants. Fluorinated LCMs (median: 10.4 ng/g, range: 1.27-116 ng/g) were frequently detected and their levels were significantly (P < 0.05) higher than those of non-fluorinated LCMs (median: 6.11 ng/g, range: not detected (ND)-76.7 ng/g). The concentrations and profiles of the observed LCMs in the soil samples from the four functional areas varied. The informal dismantling of e-waste poses a potential exposure risk to adults and infants, with median estimated daily intake (EDI, ng/kg bw/day) values of 0.0420 and 0.1013, respectively. Calculation of the hazard quotient (HQ) suggested that some LCMs (e.g., ETFMBC (1.374) and EDFPB (1.257)) may pose potential health risks to occupational workers and their families. Considering the widespread contamination and risks associated with LCMs, we strongly recommend enhancing e-waste management and regulation in Pakistan.