Effect of adding arginine at different concentrations to experimental orthodontic resins: an in vitro study.

The aim of this study was to assess the effect of adding arginine at different concentrations to commercial and experimental orthodontic resins on shear bond strength (SBS), as well as on the antimicrobial activity of arginine against S. mutans. Metal brackets were bonded onto the surface of 120 bovine incisors using Transbond, OrthoCem, and an experimental resin (ER), adding 0, 2.5, 5, and 7 wt.% of arginine. The SBS test was performed in deionized water at 37 ºC for 24 h, at 0.5 mm/min. SBS test results were subjected to two-way ANOVA and Tukey's test (α = 0.05). CFU/mL data (antimicrobial assessment) were assessed by Kruskal-Wallis and Dunn's tests (α = 0.05). No statistical difference between the resins was observed in untreated groups (p > 0.05). The addition of arginine at 2.5% (27.7 MPa) and 5% (29.0 MPa) increased the SBS of Transbond when compared (p < 0.05) to OrthoCem (18.5 and 15.6 MPa, respectively) and ER (16.3 and 18.1 MPa, respectively). Arginine at 7% improved the SBS of Transbond (24.1 MPa) and ER (21.0 MPa), which was statistically higher (p < 0.05) than OrthoCem (12.6 MPa). OrthoCem did not show a statistically significant difference at the three concentrations of arginine (p > 0.05). The addition of arginine to resins reduced the count of S. mutans (p < 0.05). As for ER, all concentrations of arginine significantly decreased CFU/mL (p < 0.05). Among commercial resins, only 7% of arginine significantly reduced CFU/mL. The addition of arginine did not interfere with the bond strength and demonstrated antibacterial activity against S. mutans.

Do the methods for cleaning the base of brackets used in indirect bonding interfere with adhesion to tooth enamel?

OBJECTIVE: The objective of this study was to evaluate the shear bond strength of metal brackets bonded with indirect bonding, under different surface treatment protocols. MATERIAL AND METHODS: 40 bovine teeth were randomly divided into four groups (n = 10), according to the type of surface treatment: G1 = 70% alcohol, G2 = air/water spray, G3 = 100-µm aluminum oxide blasting, G4 = direct boning. After drying, the standard Edgewise central incisor brackets were bonded with light-cured resin. The brackets were moved from the plaster models by means of a transfer tray made with condensation silicone, and bonded to the surface of the enamel with self-curing adhesive. The samples were submitted to shear tests by a universal test machine. Data were analyzed with SPSS 20.0 by the one-way ANOVA test and the Tukey post-test. RESULTS: No statistically significant difference (p=0.174) was observed between the mean forces measured between the group for shear strength values of the groups during the test: G1 (5.33 MPa), G2 (3.52 MPa) and G3 (4.58 MPa). CONCLUSION: The bracket surface treatment protocols presented similarities in shear bond strength test. However, alcohol 70% and oxide blasting presented higher absolute values of resistance than the water group.

Relación del plano oclusal con la altura del ángulo goníaco y proyección del mentón / Relation of the occlusal plane with the height of the gonial angle and projection of the chin

Introducción: hemos observado en nuestra práctica ortodóncica una gran cantidad de pacientes con plano oclusal inclinado, con un ángulo goníaco alto y postero-rotación mandibular. Todo parece indicar que el plano oclusal juega un papel muy importante en el desarrollo de las maloclusiones. Objetivo: mostrar en el presente caso clínico de un niño, si existe una correlación entre la inclinación del plano oclusal, la altura del ángulo goníaco, la longitud de la rama mandibular y la proyección del mentón antes y después, al corregirlo y hacerlo más horizontal con tratamiento ortodóncico. Caso clínico: paciente masculino de 11 años de edad, hiperdivergente, clase II esquelética severa, perfil convexo, apiñamiento dental superior e inferior, clase II molar, incompetencia labial severa, mordida profunda, overjet aumentado, mentón retrusivo, cervicales rectificadas y anterorotación de cabeza. El tratamiento de ortodoncia se realizó con brackets Roth slot 22 y extracciones de primeros premolares superiores e inferiores y primeros molares superiores (siendo reemplazados por los terceros molares superiores), curvas inversas, cierre de espacios con pérdida de anclaje y ajuste oclusal. Resultados: al finalizar el tratamiento, se logró mejorar la estética facial, un ángulo goníaco más desarrollado con mayor crecimiento vertical, mayor proyección del mentón, un plano oclusal más horizontal, un adecuado overbite y overjet, clase I molar y canina, antero-rotación mandibular, buena intercuspidación, oclusión funcional y excelente estabilidad oclusal sin retención, mejoría en lordosis cervical y posición de la cabeza. Conclusiones: la corrección de un plano oclusal inclinado en niños y adolescentes hiperdivergentes, puede mejorar de manera importante el vector de crecimiento, ayudar a un mayor desarrollo en la altura del ángulo goníaco y longitud de la rama mandibular, proyección del mentón al corregirlo y hacer el plano oclusal más horizontal con la mecánica ortodóntica de curvas inversas; por lo tanto, en el presente caso clínico: sí existe una correlación muy importante entre la inclinación del plano oclusal, la altura del ángulo goníaco y la proyección del mentón antes y después del tratamiento ortodóncico (AU)

Introduction: we have observed in our orthodontic practice a large number of patients with inclined occlusal plane, with a high goniac angle and posterior mandibular rotation. Everything seems to indicate that the occlusal plane plays a very important role in the development of malocclusions. Objective: to show in the present clinical case of a child, if there is a correlation between the inclination of the occlusal plane, the height of the goniac angle, the length of the mandibular branch and the projection of the chin before and after, when correcting it and making it more horizontal with orthodontic treatment. Case report: an 11 year old male patient, hyperdivergent, severe skeletal class II, convex profile, upper and lower dental crowding, molar class II, severe labial incompetence, deep bite, increased overjet, retrusive chin, rectified cervicals, and anterorotation of the head. Orthodontic treatment was performed with Roth slot 22 brackets and extractions of upper and lower first premolars and upper first molars (being replaced by upper third molars), inverse curve, space closure with loss of anchorage and occlusal adjustment. Results: at the end of the treatment, it was possible to improve facial aesthetics, a more developed gonial angle with greater vertical growth, greater chin projection, a more horizontal occlusal plane, an adequate overbite and overjet, molar and canine class I, mandibular anterorotation, good intercuspidation, functional occlusion and excellent occlusal stability without retention, improvement in cervical lordosis and head position. Conclusions: the correction of an inclined occlusal plane in hyperdivergent children and adolescents can significantly improve the growth vector, help further development in the height of the gonial angle and length of the mandibular ramus, chin protection when correcting it and making the most horizontal occlusal plane with the orthodontic mechanics of inverse curves; therefore, in the present clinical case: there is a very important correlations between the inclination of the occlusal plane, the height of the gonial angle and chin projection before and after orthodontic treatment (AU)

Effect of time and photoactivated face on bond strength of brackets and on degree of monomer conversion.

OBJECTIVE: To evaluate the effect of four different photoactivation protocols (according to "photoactivated faces" - mesial/distal, cervical/incisal or center - and "photoactivation time" - 6-3 s) of a high-power photo activator (Valo Cordless®-Ultradent) on the shear bond strength (SBS) between metal brackets and dental enamel and on the degree of conversion (DC) of an orthodontic resin. MATERIALS AND METHODS: 40 bovine incisor crowns were randomly assigned to 4 groups (n = 10). The brackets were bonded with Transbond XT® resin using 4 protocols according to the "photoactivation protocol" factor (which was subdivided into photoactivated faces and photoactivation time): V3C = 3 s + center; V6C = 6 s + center; V3M3D = 3 s on mesial + 3 s on distal; V3C3I = 3 s on cervical + 3 s on incisal. All the samples were stored for 4 months (water,37ºC) and then subjected to a SBS test (100KgF,1 mm/min). 40 resin discs were made to evaluate the monomer degree of conversion. Data from the SBS and DC were assessed by One-way ANOVA and Tukey's test (5%). Bond failures were analyzed according to the Adhesive Remnant Index (ARI) and evaluated by the Kruskal-Wallis test (5%). RESULTS: There was a statistically significant difference (p = 0.008) in the One-way ANOVA result for SBS values between all groups, but the protocols showed statistically similar results (p ≥ 0.05-Tukey's tests) concerning the photoactivated faces (V6C, V3M3D and V3C3I) and photoactivation time (V3C and V6C) factors individually. There was no statistically significant difference (p ≥ 0.05) in the One-way ANOVA result for DC values. CONCLUSION: The SBS and DC values will vary depending on the protocol applied. CLINICAL RELEVANCE: It is possible to maintain the bracket fixation quality with the use of a high-power LED photo activator associated with a shorter photoactivation time. However, it is assumed that not all types of protocols that might be applied will provide quality bonding, such as V3C, V3M3D and V3C3I, which may - depending on the SBS and DC values - affect the final treatment time, due to brackets debonding, or increase of possibility of damage to dental enamel during bracket removal. Clinical studies are suggested to confirm the hypotheses of this research.

Comparison of the accuracy of two techniques for three-dimensional digital indirect bonding of orthodontic brackets: A randomized controlled trial.

OBJECTIVE: This study aimed to clinically compare the accuracy of bracket positioning between three-dimensionally (3D) printed indirect bonding trays and vacuum-formed trays made over 3D-printed models. MATERIAL AND METHODS: Fourteen patients, planned for fixed orthodontic therapy, were randomly divided into two equal groups. For both groups, both dental arches were scanned, to acquire virtual models, brackets were virtually positioned from central incisors to second premolars, and scans for the final bracket positions were performed. In the first group, transfer trays were 3D-printed. In the second group, virtual models were 3D-printed, and vacuum-formed soft sheets were thermoformed on the printed model. Teeth were indirectly bonded and then scanned. Superimposition of the virtual and the final bracket positioning scans was performed to measure linear and angular deviations in brackets positions. RESULTS: The first group showed significantly less occlusogingival and buccolingual linear errors than the second group. No significant differences in angular deviations were found between both groups. The frequencies of clinically acceptable linear errors within 0.5 mm and angular errors within 2° showed no statistically significant difference between both groups (p> 0.05 for all measurements). The transfer errors in both groups showed linear directional biases toward the mesial, gingival and labial directions. There was no statistically significant difference in the rate of immediate debonding between both groups (10.7% and 7.1% for the first and the second groups, respectively, p=0.295). CONCLUSIONS: 3D-printed indirect bonding trays were more accurate than vacuum-formed trays, in terms of linear deviations. Both types of trays showed similar angular control.

Changes in the arch width and buccal corridor after fixed orthodontic treatment with Damon self-ligating system: premolar extraction vs. non-extraction.

INTRODUCTION: Extraction vs. non-extraction is a crucial decision in orthodontic therapy. OBJECTIVE: The aim of the present study was to investigate the changes in the dental arch width and buccal corridor after orthodontic treatment using extraction and non-extraction therapy with Damon self-ligating system. MATERIAL AND METHODS: This retrospective study consisted of 35 patients (20 female and 15 male patients with median age of 12.5 years), treated by extracting 4 or 2 premolars, and 37 patients (16 female and 21 male patients with the median age of 12.8 years), treated without premolar extraction. Both groups were treated with Damon self-ligating system. Plaster models before (T0) and after (T1) treatment were measured, and the arch width values were determined at the level of the first molars, second premolars, canines and palatal rugae. Buccal corridor width was measured using the extraoral images at T0 and T1. Paired t-test was used for the analysis of the normally distributed data, and Wilcoxon Mann-Whitney U test was used for the data with non-normal distribution. Values of p<0.05 were set as statistically significant. RESULTS: The upper intercanine width increased significantly in both groups (p<0.01). In the non-extraction group, the arch width increased significantly in the maxillary second premolar and first molar region (p<0.01) as well as in the region of the canines (p=0.04), second premolars (p=0.01) and first molars (p<0.01) of the mandible. The buccal corridor decreased significantly in the non-extraction group (p<0.01). CONCLUSION: Premolar extraction in combination with Damon self-ligating system did not lead to reduction of the dental arch width in the maxilla, nor did it increase the size of the buccal corridors.

Expression of artefacts from different orthodontic brackets and wires in cone beam computed tomography scans-an in vitro study.

OBJECTIVES: To investigate artefacts produced by different orthodontic brackets and wires in cone-beam computed tomography (CBCT) scans. MATERIALS AND METHODS: Two dental arches were made using extracted human teeth and plaster. Three pairs of acetate plates containing different brackets - metallic, ceramic, and self-ligating ceramic with NiTi clip - along with a control plate (i.e., without brackets) were prepared. Wire changes (NiTi and steel) were made during CBCT acquisitions, performed with a fixed exposure protocol. Axial slices were selected for mean gray values and standard deviation measurement in three regions of interest (buccal, lingual, and tooth). Noise and contrast-to-noise ratio (CNR) were calculated and compared among the different brackets and wires by ANOVA with a significance level of 5%. RESULTS: Overall, the buccal and tooth region were mostly affected by the metallic and self-ligating brackets, showing higher noise, and lower CNR (p < 0.05). On the other hand, less impact of ceramic brackets in the image quality was observed (p ≥ 0.05). The lingual region did not show expressive differences among the brackets and wire combinations (p ≥ 0.05). The presence of wire associated with the brackets did not worsen image quality (p ≥ 0.05). CONCLUSIONS: In conclusion, metallic and self-ligating brackets have greater artefact expression than ceramic brackets. The wire did not influence image quality. CLINICAL RELEVANCE: One should pay attention to the type of brackets when requesting a CBCT scan during treatment, as metallic and self-ligating brackets may express greater artefacts than ceramic brackets.

Experimental Bracket Design Performance on Bonding and Polymerization of Orthodontic Composite.

Objective: To evaluate the enamel bonding ability and orthodontic adhesive resin degree of conversion using the experimental bracket design. Material and Methods. Thirteen bovine teeth were used in the study. The experimental bracket was modified with a translucent region in the center of its body. After enamel etching, Orthocem orthodontic adhesive (FGM, Joinville, Brazil) was applied on the bracket base for bonding. The groups were divided as follows (n = 10 per group): (1) control (CB) with standard brackets and (2) spot bracket (SB) with experimental brackets featuring a 0.8 mm translucent region at the center using carbide bur. Shear bond strength (SBS) was evaluated after 24 hours in a universal testing machine and adhesive remnant index (ARI). The degree of conversion (DC) was analyzed using Raman spectroscopy (n = 3 per group). Data were then analyzed using Student's t-test and Mann-Whitney statistical methods. Results: The SB group exhibited a higher mean SBS (10.33 MPa) compared to the CB Group (8.77 MPa). However, there was no statistical difference between the groups (p = 0.376). Both SB and CB groups had a mean ARI score of 1. Raman analysis revealed a higher degree of conversion in the SB group (49.3%) compared to the CB group (25.9%). Conclusions: The experimental support showed a higher degree of adhesive conversion, although there was no significant increase in bond strength.

Antibacterial, cytotoxic and mechanical properties of a orthodontic cement with phosphate nano-sized and phosphorylated chitosan: An in vitro study.

OBJECTIVES: Evaluate, in vitro, the effect of incorporating nano-sized sodium trimetaphosphate (TMPnano) and phosphorylated chitosan (Chi-Ph) into resin-modified glass ionomer cement (RMGIC) used for orthodontic bracket cementation, on mechanical, fluoride release, antimicrobial and cytotoxic properties. METHODS: RMGIC was combined with Chi-Ph (0.25%/0.5%) and/or TMPnano (14%). The diametral compressive/tensile strength (DCS/TS), surface hardness (SH) and degree of conversion (%DC) were determined. For fluoride (F) release, samples were immersed in des/remineralizing solutions. Antimicrobial/antibiofilm activity was evaluated by the agar diffusion test and biofilm metabolism (XTT). Cytotoxicity in fibroblasts was assessed with the resazurin method. RESULTS: After 24 h, the RMGIC-14%TMPnano group showed a lower TS value (p < 0.001); after 7 days the RMGIC-14%TMPnano-0.25%Chi-Ph group showed the highest value (p < 0.001). For DCS, the RMGIC group (24 h) showed the highest value (p < 0.001); after 7 days, the highest value was observed for the RMGIC-14%TMPnano-0.25%Chi-Ph (p < 0.001). RMGIC-14%TMPnano, RMGIC-14%TMPnano-0.25%Chi-Ph, RMGIC-14%TMPnano-0.5%Chi-Ph showed higher and similar release of F (p > 0.001). In the SH, the RMGIC-0.25%Chi-Ph; RMGIC-0.5%Chi-Ph; RMGIC-14%TMPnano-0.5%Chi-Ph groups showed similar results after 7 days (p > 0.001). The RMGIC-14%TMPnano-0.25%Chi-Ph group showed a better effect on microbial/antibiofilm growth, and the highest efficacy on cell viability (p < 0.001). After 72 h, only the RMGIC-14%TMPnano-0.25%Chi-Ph group showed cell viability (p < 0.001). CONCLUSION: The RMGIC-14%TMPnano-0.25%Chi-Ph did not alter the physical-mechanical properties, was not toxic to fibroblasts and reduced the viability and metabolism of S. mutans. CLINICAL RELEVANCE: The addition of phosphorylated chitosan and organic phosphate to RMGIC could provide an antibiofilm and remineralizing effect on the tooth enamel of orthodontic patients, who are prone to a high cariogenic challenge due to fluctuations in oral pH and progression of carious lesions.

Percentage of patients shifting to another treatment modality: An experience-guided decision.

OBJECTIVE: This study aimed to assess the frequency with which orthodontic patients decided to shift to another type of orthodontic appliance, among conventional metal brackets, ceramic brackets, lingual brackets and clear aligner, based on their personal experiences of pain, ulcers, bad breath, hygiene issues and social difficulties. MATERIAL AND METHODS: This study comprises of patients seeking orthodontic treatment. The sample (n = 500; age group = 19-25 years) was divided equally into four groups based on the treatment modality: conventional metal brackets, ceramic brackets, lingual brackets and clear aligner. Patients rated the questionnaire using a visual analogue scale, to assess variables (such as pain, ulcer etc) that impact various treatment modalities. Subsequently, patients from all groups provided feedback regarding their treatment experiences, and expressed their preference for an alternative modality. Intergroup comparison among the four groups was done using one-way analysis of variance with Tukey's HSD post-hoc test (p ≤ 0.05). RESULTS: Patients who received lingual brackets reported higher levels of pain and ulceration, as compared to those who received clear aligners. All four groups showed statistically significant differences for ulcers during treatment (p ≤ 0.05). Of the 125 patients who received conventional metal brackets, 28% expressed a preference for clear aligner therapy, while 20% preferred ceramic brackets. In the lingual group, 56% of 125 patients preferred clear aligner therapy, and 8% preferred ceramic brackets to complete their treatment. In the ceramic group, 83% did not want to switch, whereas 17% desired to switch to clear aligner, while in aligner group no patient desired to switch. CONCLUSIONS: A higher percentage of patients from lingual brackets group chose to shift to clear aligners, followed by conventional metal brackets group and by ceramic brackets group, in this descending order. The clear aligner group demonstrated fewer issues than the other treatment modalities.

Effect of lacteal products containing probiotic in the progression of tooth decay around orthodontic brackets

Objective: To evaluate the progression of caries around orthodontic brackets after the enamel has been exposed to lacteal products containing probiotics. Methods: Orthodontic brackets were bonded to the enamel surfaces. The test specimens were randomly divided into six groups: G1-negative control; G2-positive control, exposed to culture environment only (without microorganisms); G3-exposed to the cariogenic environment and the fermented cow's milk without probiotic; G4-exposed to the cariogenic environment and fermented cow's milk with probiotic; G5-exposed to the cariogenic environment and yogurt without probiotic; and G6-exposed to the cariogenic environment and yogurt with probiotic. The groups were placed in brain heart infusion medium, supplemented with 2% sucrose and with 1x106 cells/ml of Streptococcus mutans and Streptococcus salivarius (ATCC). The Shapiro-Wilk, Levene, Student t, Kruskal-Wallis, and Mann-Whitney tests were used. Results: all groups exposed to the ATCC strains showed lower final microhardness, compared to the negative control (p0.05). Conclusions: Lacteal products are not able to prevent the progression of caries around orthodontic brackets.

Comparison of torque expression among passive self-ligating brackets with different slot depths: An in vitro study.

INTRODUCTION: The aim of this study was to assess the interaction between a 0.019×0.025-inch (″) stainless steel archwire and two types of passive self-ligating brackets with the same slot height (0.022″) and different slot depths (0.028″ and 0.026″, and to measure the archwire/slot play as well as to compare the torque expression with archwire torsions of 12°, 24°, and 36°. MATERIAL AND METHODS: An experimental device was developed along with a universal testing machine to measure torque expression in two types of brackets with 0.028″ and 0.026″ slot depths. Analysis of variance (ANOVA) and Tukey's test were performed to identify the differences between groups. RESULTS: The 0.026″ slot bracket presented greater archwire/slot play when compared to the 0.028″ bracket. Torque expression with torsions of 24° and 36° were significantly higher in the 0.028″ depth brackets when compared to the 0.026″ depth brackets. CONCLUSION: The 0.022″×0.026″ passive self-ligating brackets attached with a 0.019″×0.025″ stainless steel archwire provided no greater torque control when compared to 0.022″×0.028″ passive self-ligating brackets.

Mechanical and microbiological properties of orthodontic resin modified with nanostructured silver vanadate decorated with silver nanoparticles (ßAgVO3).

OBJECTIVE: To investigate the impact of incorporating the antimicrobial nanomaterial ß-AgVO3 into orthodontic resin, focusing on degree of conversion, surface characteristics, microhardness, adhesion properties, and antimicrobial activity. METHODS: The 3 M Transbond XT resin underwent modification, resulting in three groups (Control, 2.5% addition, 5% addition) with 20 specimens each. Fourier transform infrared spectroscopy assessed monomer conversion. Laser confocal microscopy examined surface roughness, and microhardness was evaluated using Knoop protocols. Shear strength was measured before and after artificial aging on 36 premolar teeth. Microbiological analysis against S. mutans and S. sanguinis was conducted using the agar diffusion method. RESULTS: Degree of conversion remained unaffected by time (P = 0.797), concentration (P = 0.438), or their interaction (P = 0.187). The 5% group exhibited the lowest surface roughness, differing significantly from the control group (P = 0.045). Microhardness showed no significant differences between concentrations (P = 0.740). Shear strength was highest in the control group (P < 0.001). No significant differences were observed in the samples with or without thermocycling (P = 0.759). Microbial analysis revealed concentration-dependent variations, with the 5% group exhibiting the largest inhibition halo (P < 0.001). CONCLUSIONS: Incorporating ß-AgVO3 at 2.5% and 5% concentrations led to significant differences in surface roughness, adhesion, and antimicrobial activity. Overall, resin modification positively impacted degree of conversion, surface characteristics, microhardness, and antimicrobial activity. Further research is warranted to determine clinically optimal concentrations that maximize antimicrobial benefits while minimizing adverse effects on adhesion properties. CLINICAL SIGNIFICANCE: Incorporating ß-AgVO3 into orthodontic resin could improve patient quality of life by prolonging intervention durability and reducing the impact of cariogenic microorganisms. The study's findings also hold promise for the industry, paving the way for the development of new materials with antimicrobial properties for potential applications in the health sector.

In-vitro effect of a single application of CPP-ACP pastes and different fluoridated solutions on the prevention of dental caries around orthodontic brackets.

OBJECTIVE: To assess the in-vitro effect of single applications of CPP-ACP pastes and different fluoridated solutions on the prevention of dental caries around orthodontic brackets. MATERIAL AND METHODS: Tooth/bracket sets (n=65) were immersed in artificial saliva (1h at 37ºC) and randomly subjected to single applications (100µL; 1min) of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP emulsion), CPP-ACP with fluoride (CPP-ACPF emulsion), solutions of titanium tetrafluoride (TiF4) or sodium fluoride (NaF), or no treatment (CG). Multispecies biofilm (5 x 105 CFU/mL) was formed in the presence of 2% sucrose. After 24 h, the pH and the concentration of total soluble fluoride (TSF) were analyzed by culture medium. The presence of active white spot lesions (WSL) evaluated by macroscopic examination and the percent surface mineral loss (%SML) were analyzed. Also, the topography of enamel was detected by analysis of scanning electron microscopy (SEM). The data was assessed by chi-square, Kruskal-Wallis, and Mann-Whitney tests (p < 0.05). RESULTS: Fluoride-containing compounds led to a smaller pH reduction than did CPP-ACP and CG (p<0.05). There was difference in TSF between the groups (p<0.05), denoted as TiF4> NaF > CPP-ACPF > CPP-ACP > CG. Regarding the presence of WSL and %SML, the NaF group obtained lower values (p<0.05), while TiF4 and CPP-ACPF were similar (p>0.05). SEM demonstrated that fluoride-free groups had a larger surface dissolution. CONCLUSION: Fluoridated groups including solutions and CPP-ACPF were more effective than CPP-ACP in reducing enamel demineralization around orthodontic brackets after a single application.

Colagem indireta no tratamento orto-cirúrgico imediato ­ relato de caso / Indirect bonding in immediate ortho-surgical treatment ­ case report

Por conta das irregularidades da superfície vestibular, dificuldade de colagem em algumas regiões, como também mais facilidade na confecção de arco passivo para cirurgia ortognática de benefício antecipado, a técnica da colagem indireta vem ganhando espaço. Assim, o objetivo do trabalho é relatar um caso clínico de um paciente com 27 anos de idade sem comorbidade sistêmica e diagnosticado com ameloblastoma na mandíbula, na qual foi realizada uma colagem indireta para possibilitar a confecção do arco cirúrgico de forma passiva e, com isso, a cirurgia imediata. Por meio da técnica de colagem indireta, foi feita a colagem dos bráquetes no modelo de gesso e, após a colagem, foi confeccionado o arco passivo superior e inferior. Com os guias de colagem indireta e os arcos prontos, realizou-se a colagem na boca do paciente, os arcos cirúrgicos foram instalados e o mesmo foi encaminhado para realização da cirurgia de remoção do ameloblastoma. Erros no posicionamento dos bráquetes irão interferir no resultado final, aumentando, assim, o tempo de trabalho. A técnica da colagem indireta tem se demonstrado um avanço para a Ortodontia, otimizando o tempo de atendimento clínico como também o tempo cirúrgico nos casos de benefício antecipado. (AU)

Due to the irregularities of the vestibular surface, difficulty in gluing in some regions, as well as ease in creating a passive arch for orthognathic surgery with anticipated benefits, the indirect bonding technique has been gaining ground. Thus, the objective of the work is to report a clinical case of a 27-year-old patient without systemic comorbidity and diagnosed with ameloblastoma in the mandible, to whom indirect bonding was performed to enable the creation of the surgical arch in a passive way and, with this, the immediate surgery. Using the indirect bonding technique, the brackets were bonded to the plaster model and, after bonding, the upper and lower passive arch was created. With the indirect bonding guides and the archwires ready, the bonding was done in the patient's mouth, the surgical archwires were installed, and the patient was sent to undergo surgery to remove the ameloblastoma. Errors in the positioning of the brackets will interfere with the final result, thus increasing working time. The indirect bonding technique has proven to be an advance for Orthodontics, optimizing clinical care time as well as surgical time in cases of anticipated benefit (AU)

Eficiência da prescrição de bráquetes ortodônticos no tratamento com diferentes sistemas de bráquetes - uma proposta clínica / Orthodontic bracket prescription efficiency in treatment with different bracket systems - a clinical proposal

Com a diversificação das prescrições existentes, a correta escolha de acordo com a necessidade individual de cada má oclusão pode ser importante para estabelecer maior controle biomecânico durante o tratamento ortodôntico. Este estudo teve como objetivo avaliar o tratamento ortodôntico com a versatilidade na associação de diferentes prescrições em um relato de caso clínico e determinar se existe alguma relação com a dimensão vertical, transversal e o perímetro de arco que podem contribuir com a estabilidade e longevidade do tratamento ortodôntico. A prescrição, quando corretamente indicada, tem impacto no controle do movimento dentário para estabelecer oclusão, estética e estabilidade adequadas. Concluiu-se que o surgimento de novas prescrições tende a favorecer ao máximo a abrangência de mais pacientes no tratamento ortodôntico (AU)

With the diversification of existing bracket prescriptions, the correct choice according to the individual needs of each malocclusion is essential to establish greater biomechanical control during orthodontic treatment. This study aimed to evaluate orthodontic treatment with the versatility in association of different prescriptions in a clinical case report and to determine whether there is any relationship with the vertical dimension, transverse dimension, and arch perimeter that can contribute to the stability and longevity of the orthodontic treatment. The prescription, when correctly indicated, has an impact on the control of tooth movement to establish proper occlusion, esthetics, and stability. It was concluded that the emergence of new prescriptions favors the maximum coverage of more patients in orthodontic treatment. (AU)

O YouTube oferece uma fonte confiável de informação sobre bráquetes autoligados? / Does YouTube offer a reliable source of information about self-ligating braces?

Este estudo teve por objetivo avaliar e analisar as informações acerca do tema bráquetes autoligados publicados na plataforma YouTube. Realizou-se busca na plataforma entre os dias 10 e 15 de janeiro de 2022 com o intuito de identificar os vídeos mais relevantes utilizando-se o termo "bráquete autoligado". Atribuiu-se um critério de 7 pontos para classificar os vídeos como satisfatórios e insatisfatórios. Uma escala global de qualidade (QGS) foi utilizada para examinar a qualidade dos vídeos. Para avaliar a confiabilidade, foi utilizado um questionário adaptado do DISCERN de 5 questões. Foram convidados dois ortodontistas experientes na área para avaliarem os vídeos, correlacionar e, posteriormente, comparar as informações. Inicialmente foram encontrados 100 vídeos e, após aplicação dos critérios de exclusão, chegou--se a 27 vídeos. A maioria das mídias foram criadas por ortodontistas. Os vídeos criados por generalistas obtiveram melhor escore e também houve diferença significativa no número de comentários e taxa de interação p<0,05. Não foi observada diferença entre os escores e a origem dos vídeos p>0,05. A média do escore GQS foi de 2,25, do DISCERN 1,18, e 19 vídeos foram classificados como suficientes e 8 vídeos como insuficientes. Concluiu-se que a maioria dos vídeos não exibiu uma fonte confiável de informação e a origem das mídias não influenciou os resultados dos critérios de conteúdos nem de confiabilidade.(AU)

This study aimed to evaluate the information on the subject of self-ligating brackets published on the YouTube platform. A search was carried out on the platform between January 10 and 15, 2022 in order to identify the most relevant videos using the term "self-ligating bracket". A criterion of 7 points was assigned to classify the videos as satisfactory and unsatisfactory. A global quality scale (QGS) was used to examine the quality of the videos. To assess reliability, an adapted 5-question DISCERN questionnaire was used. Two experienced orthodontists in the field were invited to evaluate the videos, correlate and later compare the information. Initially, 100 videos were found and, after applying the exclusion criteria, 27 videos were reached. Most media were created by orthodontists. Videos created by generalists had a better score and there was also a significant difference in the number of comments and interaction rate p<0.05. No difference was observed between the scores and the origin of the videos p>0.05. The average GQS score was 2.25, from DISCERN 1.18, and 19 videos were classified as sufficient and 8 videos as insufficient. It was concluded that most videos did not show a reliable source of information and the origin of the media did not influence the results of the content or reliability criteria(AU)

Eficiência de métodos de remoção de adesivo residual após remoção de braquetes da superfície de esmalte dentário bovino / Efficiency of adhesive removal methods after residual orthodontic treatment of bovine dental enamel surface

Os adesivos que unem braquetes (BQTs) ao esmalte dentário atendem às necessidades clínicas, pois resistem às forças mastigatórias bem como às forças da mecânica ortodôntica. No entanto, estes devem possibilitar sua remoção sem causar maiores danos ao esmalte. Resíduos do sistema adesivo (SA) ou pequenos defeitos no esmalte após remoção do BQT favorecem a adesão de biofilme e alteram a refração da luz, culminando em problemas estéticos. Embora existam muitos métodos de remoção, não há consenso na literatura quanto a indicação deles. Objetivou-se comparar a eficiência de dois métodos de remoção de adesivo: broca multilaminada de Zircônia (Z) e inserto ultrassônico com crescimento de diamante por deposição química de vapor (CVD). BQTs foram cimentados na face vestibular de 26 dentes incisivos bovinos, sendo removidos utilizando alicate ortodôntico. Em seguida, os dentes foram divididos em dois grupos para remoção do SA remanescente: grupo Z (broca de Zircônia multilaminada) e grupo D (inserto ultrassônico CVD). Todas as amostras passaram por etapa de polimento final. Os dados foram coletados através de escaneamento digital e moldagem com silicone de adição em ambos os grupos para avaliação em cada uma das etapas: inicial, após remoção do BQT, após remoção do adesivo e após polimento. Em seguida, os moldes obtidos foram vertidos em modelos de resina epóxi que, posteriormente, foram metalizadas para análise em microscópio eletrônico de varredura (MEV) e em estereomicroscopia. Os dados foram tabulados no software Microsoft Excel ® versão 2010 e submetidos à análise estatística no software JASP (Universidade de Amsterdã, ⲁ = 0,05), versão 0.15, ambiente Windows, sendo realizado o teste "T de Student". Observou-se que a remoção do SA acarreta danos à superfície do esmalte, corroborando a literatura encontrada. Houve diferenças na rugosidade da superfície do esmalte, havendo maior rugosidade no grupo Z. No entanto, após polimento, não houve diferença estatística entre os dois grupos. As pontas CVD apresentaram maior tempo para desgaste do SA residual, mas menor potencial de danos às estruturas dentárias sadias, revelando-se promissoras na preservação da superfície dentária. (AU)

Adhesives that bond brackets (BQTs) to tooth enamel meet clinical needs, as they resist to chewing forces as well as to the forces of orthodontic mechanics. However, these must allow for removal without causing further damage to the enamel. Residues from the adhesive system (AS) or small defects in the enamel after BQT removal favor biofilm adhesion and alter light refraction, resulting in aesthetic problems. Although there are many removal methods, there is no consensus in the literature regarding their indication. The objective was to compare the efficiency of two adhesive removal methods: multilaminate zirconia drill (Z) and ultrasonic insert with diamond growth by chemical vapor deposition (CVD). BQTs were cemented on the buccal surface of 26 bovine incisor teeth and removed using orthodontic pliers. Then, the teeth were divided into two groups to remove the remaining adhesive system: group Z (multilaminate zirconia bur) and group D (CVD ultrasonic insert). All samples went through the final polishing stage. Data were collected through digital scanning and molding with added silicone in both groups for evaluation at each stage: initial, after removal of the BQT, after removal of the adhesive, and after polishing. Then, the molds obtained were poured into epoxy resin models that were subsequently metalized for analysis under a scanning electron microscope (SEM) and stereomicroscopy. The data were tabulated in the Microsoft Excel ® software version 2010 and subjected to statistical analysis in the JASP software (University of Amsterdam, ⲁ = 0.05), version 0.15, Windows environment, using the "Student's T" test. It was observed that removing the AS causes damage to the enamel surface, corroborating the literature found. There were differences in the roughness of the enamel surface, with greater roughness in group Z. However, the two groups had no statistical difference after polishing. The CVD insert showed a longer time for wear of residual SA, but a lower potential for damage to healthy dental structures, proving to be promising in preserving the tooth surface(AU)

Efficacy of ClinproTMXT Varnish surrounding brackets on the enamel surface of white spot lesion.

Orthodontics patients usual develop demineralization and present cavity caries lesions after six months. Minimally invasive procedures have been the goal in modern dental practice. The aim of this study was to evaluate the effect of ClinproTMXT Varnish, on the enamel surface roughness and severity of white spot lesions. Twenty premolars were submitted to bond brackets and experimental induction of demineralization and randomly divided into 2 groups: GI - fluoride varnish (Colgate Duraphat®); GII - Ionomeric Sealant (ClinproTMXT Varnish). The treatment was applied around the brackets. The surface roughness of specimens was analyzed, before treatment and 12 weeks after treatment by laser confocal microscopy, and the severity of the white spot lesion was by laser fluorescence device. The data were analyzed by non-parametric Wilcoxon and Mann-Whitney Test, at 5% significance, roughness percentage reduction was performed. The severity of demineralization decreased in both, GI (p = 0.005) and GII (p = 0.019). Enamel superficial roughness levels decreased in GI and GII. As well as the roughness percentage, being more expressive in the ClinproTMXT Varnish group (85,09%). Colgate Duraphat® or Clinpro™ XT Varnish reduced the severity of the demineralization and decreased the superficial roughness on the enamel. The Clinpro™ XT Varnish was superior to superficial roughness on enamel.