Comparison of thermal, rheological properties of Finnish Pinus sp. and Brazilian Eucalyptus sp. black liquors and their impact on recovery units.

Black liquor (BL) is the major bioproduct and biomass fuel in pulp mill processes. However, the high viscosity of BL makes it a challenging material to work with, resulting in issues with evaporators and heat exchangers during its transport and processing. The thermal and rheological properties of BLs from Pinus sp. (PBL) and Eucalyptus sp. (EBL) were studied. FTIR spectra revealed the presence of the characteristic functional groups and the chemical composition in liquors. TGA/DTG curves showed three characteristic degradation stages related to evaporation of water, pyrolysis of organic groups, and condensation of char. Rheologically, liquors are classified as non-Newtonian and with comportment pseudoplastic. Their rheological dynamic shear properties included a linear viscoelastic region up to 1% shear strain, while frequency sweeps showed that storage modulus (G') > loss modulus (G''), thus confirming the solid-like behavior of both BLs. The rheological study demonstrated that increasing the temperature and oscillatory deformations of PBL and EBL decreased their degree of viscoelasticity, which could favor their pumping and handling within the pulp mill, as well as the droplet formation and swelling characteristics in the recovery furnace.

Sustainable removal of tetracycline and paracetamol from water using magnetic activated carbon derived from pine fruit waste.

This work presents highly porous magnetic activated carbon nanoparticles (MPFRC-A) derived from pine fruit residue. The MPFRC-A were produced through a three-step process: physical activation (carbonization temperature: 110-550 °C), chemical activation (H2SO4 (0.1 N, 96%)), and co-precipitation. These nanoparticles were then used to remove tetracycline (TC) and paracetamol (PC) from water. Functionalization with Fe3O4 nanoparticles on the surface of the pine fruit residue-derived activated carbon (PFRC-A) resulted in high saturation magnetization, allowing for separation from aqueous solution using an external magnet. The MPFRC-A adsorbent was characterized by Brunauer-Emmett-Teller (BET) analysis, Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and Energy-dispersive X-ray spectroscopy (EDX) analyses, In the experimental section, the effects of various factors on the adsorption process were investigated, including pH, contact time, initial pollutant concentrations, adsorbent dosage, and temperature. Based on these investigations, adsorption isotherm models and kinetics were studied and determined. The results showed that MPFRC-A exhibited a large specific surface area (182.5 m2/g) and a high total pore volume (0.33 cm3/g). The maximum adsorption capacity was achieved at pH 6 and 5 for PC and TC drugs with an adsorbent dose of 400 mg and an initial concentration of 20 mg/L at 25 °C. The study revealed that the experimental data were well-fitted by the Langmuir isotherm model (R2 > 0.98), with maximum uptake capacities of 43.75 mg/g for TC and 41.7 mg/g for PC. Outcomes of the adsorption thermodynamics shows non-spontaneity of the reaction and the adsorption process by all adsorbents was endothermic.

What are the different biomolecules involved in the selective recovery of REEs from mining wastewater using FeNPs synthesized from two plant extracts?

Extracting rare earth elements (REEs) from wastewater is crucial for saving the environment, sustainable use of natural resources and economic growth. Reported here is a simple, low cost and one-step synthesis of Fe nanoparticles (FeNPs) based on two plant extracts having the ability to recover REEs. The synthesis of FeNPs using Excoecaria cochinchinensis leaves extract (Ec-FeNPs) exhibited high selectivity for heavy rare earth due to unique biomolecules, achieving separation coefficients (Kd) of 3.16 × 103-4.04 × 106 mL/g and recovery efficiencies ranging from 71.7 to 100 %. Conversely, the synthesis of FeNPs using Pinus massoniana lamb extract (PML-FeNPs) revealed poorer REE recovery efficiencies of 7.2-86.7 %. To understand the differences between Ec-FeNPs and PML-FeNPs in terms of selectivity and efficiency, LC-QTOF-MS served to analyze the biomolecules differences of two plant extracts. In addition, various types of characterization were carried out to identify the different functional groups encapsulated on the surface of FeNPs. These results reveal the source of the difference in the selectivity of Ec-FeNPs and PML-FeNPs for REEs. Furthermore, during DFT calculations, it was found that biomolecules with varying affinities for the surface of FeNPs interact with each other, leading to the formation of structures that exhibit high reactivity towards REEs. Finally, incorporating Spearman correlation analysis demonstrates that the selective removal efficiency of REEs was closely linked to surface complexation, ion exchange, and electrostatic adsorption. Consequently, this work strongly highlights the potential for the practical application of novel adsorbents in this field.

Pinus eldarica (L.) bark as urban atmospheric trace element pollution bioindicator: pollution status, spatial variations, and quantitative source apportionment based on positive matrix factorization receptor model.

In this study, a total of 180 Pinus eldarica bark samples were collected from different regions of Hamedan megacity, Iran, in 2023, and contents of Cd, Cr, Cu, Mn, Ni, Pb, and Zn in the samples were determined using ICP-OES. The results illustrated that the average contents of all the analyzed elements were greater than those in the background contents, which presumably demonstrated anthropogenic sources of these potentially toxic elements (PTEs). The greatest concentrations of the analyzed PTEs for different functional areas were observed in specimens collected from commercial or industrial areas, indicating the impact of human entries. The I-geo values were in the range of "unpolluted to moderately polluted" to "moderately to heavily polluted", PI showed "moderate to very high pollution", and PLI reflected high to very high pollution levels for the whole study area. Additionally, the cumulative mean value of ecological risk (RI) was found to be 152, demonstrating moderate ecological risk across the study area. The results of positive matrix factorization (PMF) showed that the PTE contamination in the air of Hamedan could mainly have an anthropogenic origin (82.7%) and that the traffic emissions as the primary pollution source (33.6%) make the highest contribution to the PTE pollution and ecological risks in the study area. In residential areas, demolition and construction activities could be considered the main sources of PTEs, while in commercial and industrial areas traffic emissions and industrial emissions, could be regarded as the main sources of such pollution, respectively. In conclusion, this study provides a useful approach to identifying the sources and contributions of the toxic elements in different functional areas and can inform future endeavors that aim at managing and controlling metal element pollution.

Study on the extraction, purification, stability, free radical scavenging kinetics, polymerization degree and characterization of proanthocyanidins from Pinus koraiensis seed scales.

To efficiently harness resources from Pinus koraiensis seed scales, a type of forestry waste, rigorous studies on the extraction, purification, stability, and free radical scavenging capacity of the proanthocyanidins derived from these seed scales were conducted. Kinetic models showed that under ultrasonic conditions, the proanthocyanidins content reached 2.66 mg/g within 0.5 h. The optimal storage parameters include darkness, 4 °C, and pH 4. The degrees of polymerization of the mixture and the high- and low-polymer components were 4.89, 7.42 and 3.07, respectively, with the low-polymer component exhibiting the highest radical scavenging activity. Through HPLC-QE-MS/MS, 1H NMR, and FT-IR analyses, we identified proanthocyanidin B1, proanthocyanidin B2, (-)-epicatechin, and polymeric trimer esters. The Pinus koraiensis proanthocyanidins exhibited a high molecular weight, a complex internal molecular structure, and commendable stability, with crystallization requiring elevated temperatures. Therefore, the proanthocyanidins from Pinus koraiensis seed scales have emerged as highly promising novel natural antioxidants.

Influence of lignin and cellulose from termite-processed biomass on biochar production and evaluation of chromium VI adsorption.

The increasing water contamination by toxic heavy metals, particularly hexavalent chromium, has become a significant environmental concern. This study explores the pyrolysis of termite-processed biomass, specifically Pinus elliottii particleboard and its termite droppings (TDs), to produce biochar and its application for chromium (VI) adsorption. Termite droppings, rich in lignin, and particleboard, rich in cellulose, were pyrolyzed at various temperatures to assess the effect of biomass composition on biochar properties. The study found that lignin-rich termite droppings produced biochar with higher fixed carbon content and specific surface area than cellulose-rich particleboard biochar. FTIR and Raman spectroscopy revealed significant molecular structure changes during pyrolysis, which influenced the adsorption capabilities of the biochar. Adsorption experiments demonstrated that TD biochar exhibited significantly higher chromium (VI) adsorption capacity, attributed to its distinct chemical composition and enhanced surface properties due to higher lignin content. These findings underscore the crucial role of lignin in producing efficient biochar for heavy metal adsorption, highlighting the practical applicability of termite-processed biomass in water purification technologies.

Andrastin-type meroterpenoids, α-pyrone polyketides, and sesquicarane derivatives from Penicillium sp., a fungus isolated from Pinus koraiensis seed.

The genus Penicillium has provided us with the household antibiotic penicillin and the well-known lipid-lowering agent mevastatin. The strain Penicillium sp. SZ-1 was found to grow vigorously in an intact Pinus koraiensis seed, it is inferred that the strain may develop unique mechanisms associated with the biosynthesis of rare metabolites. Further fermentation of the strain on solid rice medium yielded thirteen undescribed compounds, including three andrastin-type meroterpenoids (1-3), two α-pyrone polyketides (4 and 5), and eight sesquicarane derivatives (6-13), along with seven known compounds (14-20). Their structures were determined by detailed analysis of the spectroscopic and spectrometric data (NMR and HRESIMS), in addition to comparisons of the experimental and calculated ECD data for absolute configurational assignments. The hemiacetal moiety in compounds 1 and 2 and the 3α-hydroxy group in compound 3 were rarely found in the andrastin-type meroterpenoid family. The sesquicaranes belong to a small group of sesquiterpenoid that are rarely reported. Bioassay study showed that compound 1 exhibited inhibitory effects against Staphylococcus aureus ATCC 29213 and Escherichia coli ATCC 25922 with MIC values of 64 and 32 µg/mL, respectively. In addition, compounds 1 and 3 displayed weak DPPH radical scavenging activities. The andrastins and sesquicaranes in this study enriched the structural diversity of these classes of terpenoids. Of note, this study is the first report on the metabolites of a fungus isolated from P. koraiensis seed.

Red Pine Bark Extract Alleviates Akt/GSK-3ß Signaling Disruption in the Hippocampus of Streptozotocin-Induced Diabetic Sprague-Dawley Rats.

This study investigates whether red pine (Pinus densiflora Sieb. et Zucc.) bark extract (PBE) can alleviate diabetes and abnormal apoptosis signaling pathways in the hippocampus of streptozotocin (STZ)-induced diabetic Sprague-Dawley (SD) rats. Two dosages of PBE (15 and 30 mg/kg of body weight/day) were administered orally to STZ-induced diabetic SD rats for 20 days. Blood glucose level and body weight were measured once per week. After 20 days of oral administration of PBE, the rat hippocampus was collected, and the production of Akt, p-Akt, GSK-3ß, p-GSK-3ß, tau, p-tau, Bax, and Bcl-2 proteins were determined by western blot analysis. A decrease in blood glucose level and recovery of body weight were observed in PBE-treated diabetic rats. In the Akt/GSK-3ß/tau signaling pathway, PBE inhibited diabetes-induced Akt inactivation, GSK-3ß inactivation, and tau hyperphosphorylation. The protein production ratio of Bax/Bcl-2 was restored to the control group level. These results suggest that PBE, rich in phenolic compounds, can be used as a functional food ingredient to ameliorate neuronal apoptosis in diabetes mellitus.

The anti-amoebic activity of Pinus densiflora leaf extract against the brain-eating amoeba Naegleria fowleri.

Naegleria fowleri invades the brain and causes a fatal primary amoebic meningoencephalitis (PAM). Despite its high mortality rate of approximately 97%, an effective therapeutic drug for PAM has not been developed. Approaches with miltefosine, amphotericin B, and other antimicrobials have been clinically attempted to treat PAM, but their therapeutic efficacy remains unclear. The development of an effective and safe therapeutic drug for PAM is urgently needed. In this study, we investigated the anti-amoebic activity of Pinus densiflora leaf extract (PLE) against N. fowleri. PLE induced significant morphological changes in N. fowleri trophozoites, resulting in the death of the amoeba. The IC50 of PLE on N. fowleri was 62.3±0.95 µg/ml. Alternatively, PLE did not significantly affect the viability of the rat glial cell line C6. Transcriptome analysis revealed differentially expressed genes (DEGs) between PLE-treated and non-treated amoebae. A total of 5,846 DEGs were identified, of which 2,189 were upregulated, and 3,657 were downregulated in the PLE-treated amoebae. The DEGs were categorized into biological process (1,742 genes), cellular component (1,237 genes), and molecular function (846 genes) based on the gene ontology analysis, indicating that PLE may have dramatically altered the biological and cellular functions of the amoeba and contributed to their death. These results suggest that PLE has anti-N. fowleri activity and may be considered as a potential candidate for the development of therapeutic drugs for PAM. It may also be used as a supplement compound to enhance the therapeutic efficacy of drugs currently used to treat PAM.

Characterization of chitosan film incorporated pine bark extract and application in carp slices packaging.

Active films based on chitosan incorporated with pine bark extract (PBE) were prepared and characterized. Subsequently, these films were utilized for packaging carp slices in refrigerated storage at 4 ± 1 °C. Analysis of the physicochemical properties and biological activity of the active films revealed that, except for water content, all assessed indices showed an increasing trend with an increase in the amount of supplemental PBE. As this trend progresses, scanning electron microscopy (SEM) analysis revealed deposition on the film surface accompanied by transverse lines and fractures, while the color of the film gradually changed from light yellow to reddish-brown. Fourier transform infrared spectroscopy (FTIR) indicated that the phenolic hydroxyl groups in PBE interacted with the hydrogen in the amino groups of chitosan molecules to form non-covalent bonds. X-ray diffraction analysis (XRD) showed that the reaction between PBE and chitosan altered the crystalline structure of chitosan molecules. Moreover, the analysis of the effects of active films on the pH, water-holding capacity, thiobarbituric acid values, and the total bacterial counts of carp slices revealed that in terms of preservation, films containing 30 % PBE were the most effective, using which the shelf life of carp slices could be extended by 50 %.

Tree Species-Dependent Inactivation of Coronaviruses and Enteroviruses on Solid Wood Surfaces.

The ongoing challenge of viral transmission, exemplified by the Covid pandemic and recurrent viral outbreaks, necessitates the exploration of sustainable antiviral solutions. This study investigates the underexplored antiviral potential of wooden surfaces. We evaluated the antiviral efficacy of various wood types, including coniferous and deciduous trees, against enveloped coronaviruses and nonenveloped enteroviruses like coxsackie virus A9. Our findings revealed excellent antiviral activity manifesting already within 10 to 15 min in Scots pine and Norway spruce, particularly against enveloped viruses. In contrast, other hardwoods displayed varied efficacy, with oak showing effectiveness against the enterovirus. This antiviral activity was consistently observed across a spectrum of humidity levels (20 to 90 RH%), while the antiviral efficacy manifested itself more rapidly at 37 °C vs 21 °C. Key to our findings is the chemical composition of these woods. Resin acids and terpenes were prevalent in pine and spruce, correlating with their antiviral performance, while oak's high phenolic content mirrored its efficacy against enterovirus. The pine surface absorbed a higher fraction of the coronavirus in contrast to oak, whereas enteroviruses were not absorbed on those surfaces. Thermal treatment of wood or mixing wood with plastic, such as in wood-plastic composites, strongly compromised the antiviral functionality of wood materials. This study highlights the role of bioactive chemicals in the antiviral action of wood and opens new avenues for employing wood surfaces as a natural and sustainable barrier against viral transmissions.

Azithromycin removal using pine bark, oak ash and mussel shell.

Adsorption is considered an interesting option for removing antibiotics from the environment because of its simple design, low cost, and potential efficiency. In this work we evaluated three by-products (pine bark, oak ash, and mussel shell) as bio-adsorbents for the antibiotic azithromycin (AZM). Furthermore, they were added at doses of 48 t ha-1 to four different soils, then comparing AZM removal for soils with and without bio-adsorbents. Batch-type experiments were used, adding AZM concentrations between 2.5 and 600 µmol L-1 to the different bio-adsorbents and soil + bio-adsorbent mixtures. Regarding the bio-adsorbents, oak ash showed the best adsorption scores (9600 µmol kg-1, meaning >80% retention), followed by pine bark (8280 µmol kg-1, 69%) and mussel shell (between 3000 and 6000 µmol kg-1, 25-50% retention). Adsorption data were adjusted to different models (Linear, Freundlich and Langmuir), showing that just mussel shell presented an acceptable fitting to the Freundlich equation, while pine bark and oak ash did not present a good adjustment to any of the three models. Regarding desorption, the values were always below the detection limit, indicating a rather irreversible adsorption of AZM onto these three by-products. Furthermore, the results showed that when the lowest concentrations of AZM were added to the not amended soils they adsorbed 100% of the antibiotic, whereas when the highest concentrations of AZM were spread, the adsorption decreased to 55%. However, when any of the three bio-adsorbents was added to the soils, AZM adsorption reached 100% for all the antibiotic concentrations used. Desorption was null in all cases for both soils with and without bio-adsorbents. These results, corresponding to an investigation carried out for the first time for the antibiotic AZM, can be seen as relevant in the search of low-cost alternative treatments to face environmental pollution caused by this emerging contaminant.

Development of bioactive films loaded with extract and polysaccharide of Pinus brutia bark.

Society's interest in natural and clean products in many areas, such as food and cosmetics, has increased considerably. It has led to the development of new techniques in the packaging of products so that the wastes from the preferred products can be recycled. In this context, Pinus brutia bark was preferred within the scope of the study to transform natural wastes into functional components and use them as packaging material. P. brutia bark (PBB) samples were collected from Bursa, Turkey. PBB samples were ultrasonically extracted using various solvents (acetone, butanol, ethanol, ethyl acetate, hexane, methanol, petroleum ether, and water) and a solvent-acidic hydrolysis system. The phenolic content profile of PBB samples was determined using high-performance liquid chromatography with diode-array detection, and total flavonoid content, antioxidant capacity, and total phenolic content were determined. Chitosan-polyvinyl alcohol (CS-PVA) films loaded with polysaccharides and containing methanolic extract were developed. The physical, chemical, and mechanical properties of the films were characterized. It is known that the thickness of the films determines the mechanical properties required to maintain the integrity of the packaging during storage and transport. From the results of the study, it was concluded that the elongation at break value was higher in CS-PVA-PBB-M films (111.08% ± 10.46%), Young's modulus (31.74 ± 21.37 N/mm2), and tensile strength (3.01 ± 0.50 N/mm2) values were higher in CS-PVA films. In this case, it was concluded that adding proanthocyanidin to edible films gives flexibility to the films.

Biomass-Based, Dual Enzyme-Responsive Nanopesticides: Eco-friendly and Efficient Control of Pine Wood Nematode Disease.

Pine wood nematode (PWN) disease is a globally devastating forest disease caused by infestation with PWN, Bursaphelenchus xylophilus, which mainly occurs through the vector insect Japanese pine sawyer (JPS), Monochamus alternatus. PWN disease is notoriously difficult to manage effectively and is known as the "cancer of pine trees." In this study, dual enzyme-responsive nanopesticides (AVM@EC@Pectin) were prepared using nanocoating avermectin (AVM) after modification with natural polymers. The proposed treatment can respond to the cell wall-degrading enzymes secreted by PWNs and vector insects during pine tree infestation to intelligently release pesticides to cut off the transmission and infestation pathways and realize the integrated control of PWN disease. The LC50 value of AVM@EC@Pectin was 11.19 mg/L for PWN and 26.31 mg/L for JPS. The insecticidal activity of AVM@EC@Pectin was higher than that of the commercial emulsifiable concentrate (AVM-EC), and the photostability, adhesion, and target penetration were improved. The half-life (t1/2) of AVM@EC@Pectin was 133.7 min, which is approximately twice that of AVM-EC (68.2 min). Sprayed and injected applications showed that nanopesticides had superior bidirectional transportation, with five-times higher AVM contents detected in the roots relative to those of AVM-EC when sprayed at the top. The safety experiment showed that the proposed treatment had lower toxicity and higher safety for nontarget organisms in the application environment and human cells. This study presents a green, safe, and effective strategy for the integrated management of PWN disease.

Distribution of 35 Polycyclic Aromatic Hydrocarbons in Pine Needle Samples from Selected Locations in the Republic of Korea.

Polycyclic aromatic hydrocarbons (PAHs), dust, and wax were measured in pine needles, and PAHs were also measured in surface soil. Pearson correlation analysis was performed between the analytical values. The main compounds responsible for the increase in total PAHs were non-carcinogenic phenanthrene and fluoranthene. Therefore, the % content of carcinogenic PAHs decreased with a slope = -0.037 (r = 0.47, p < 0.01), as the total PAH concentration in pine needles increased. Correlations between individual PAHs in pine needles and surface soil were very high when only low-number ring PAHs (2R- and 3R-PAHs) were statistically analyzed and significant when only high-number ring PAHs were statistically analyzed. Low-number ring PAH mainly moves in the gas phase and diffuses into the wax layer, so it was found to be statistically significant with the wax content of pine needles. High-number ring PAHs showed a high correlation with the amount of dust in pine needles because they mainly attached to dust particles and accumulated on the surface of pine needles. The ratios of fluoranthene/pyrene and methylphenanthrene/phenanthrene for predicting the origin of atmospheric PAHs have also been proven valid for pine needles.

Insights into hydrothermal treatment of biomass blends: Assessing energy yield and ash content for biofuel enhancement.

This study explores the Hydrothermal Carbonization (HTC) treatment of lignocellulosic biomass blends, delving into the influence of several key parameters: temperature, additive nature and dosage, residence time, and biomass composition. Rapeseeds, Pinus radiata sawdust, oat husks, and pressed olive served as the studied biomasses. One hundred twenty-eight experiments were conducted to assess the effects on mass yield (MY), energy yield (EY), higher heating value (HHV), and final ash content (ASH) by a Factorial Experimental Design. The derived model equations demonstrated a robust fit to the experimental data, averaging an R2 exceeding 0.94, affirming their predictive accuracy. The observed energy yield ranged between 65% and 80%, notably with sawdust and olive blends securing EY levels surpassing 70%, while rapeseed blends exhibited the highest HHV at 25 MJ/kg. Temperature emerged as the most influential factor, resulting in an 11% decrease in MY and a substantial 2.20 MJ/kg increase in HHV. Contrastingly, blend composition and additive presence significantly impacted ASH and EY, with all blends exhibiting increased ASH in the presence of additives. Higher initial hemicellulose and aqueous extractive content in raw biomass correlated proportionally with heightened HHV.

Extraction of tannin, colour and aroma compounds in pinot noir wines as affected by clone selection and whole bunch addition.

Our previous study revealed stem inclusion fermentation reduced anthocyanin, and increased tannin and aroma compounds responsible for green notes. This study further investigated the effect of clone selection and whole bunch fermentation on Pinot noir wine composition, with focus on tannin composition. Three treatments were conducted using two clones (AM10/5 and UCD5) in 2021 and 2022: 100% destemmed (DS), 30% whole bunch (WB30), and 60% whole bunch (WB60). WB60 increased stem and skin derived tannins but reduced seed derived tannin proportion in wines. Clone selection had an impact on tannin composition and an even greater impact on tannin concentration, colour, and aroma compounds. AM10/5 produced wines with higher tannin, polymeric pigments and darker colour. AM10/5 wines also had higher concentration of phenylethyl alcohol, but lower concentrations of 3-isobutyl-2-methoxypyrazine and ethyl esters, indicating more floral but less fruity and green notes.

Integrated biorefinery approach for utilization of wood waste into levulinic acid and 2-Phenylethanol production under mild treatment conditions.

In a bid to explore the on-site biorefinery approach for conversion of forestry residues, lignocellulosic biomass into value-added products was studied. The bark white pine wood was subjected to the microwave technique of fast and slow hydrolysis under varying acid and biomass concentrations to produce levulinic acid (LA). The HCl (2% v/v) and plant biomass (1% w/v) were identified as the optimum conditions for fast wood hydrolysis (270 ºC for 12 sec), which led to maximum LA yield of 446.68 g/kgPB. The proposed sustainable approach is mild, quick, and utilized a very low concentration of the HCl for the production of LA. The hydrolysate was used as a medium for Kluyveromyces marxianus growth to produce 2-phenylethanol (2-PE). K. marxianus used 74-95% of furfural from hydrolysate as a co-substrate to grow. The proposed model of the integrated biorefinery is an affordable on-site approach of using forest waste into localized solutions to produce LA and 2-PE.

Variation pattern in the macromolecular (cellulose, hemicelluloses, lignin) composition of cell walls in Pinus tabulaeformis tree trunks at different ages as revealed using multiple techniques.

The plant cell wall is a complex, heterogeneous structure primarily composed of cellulose, hemicelluloses, and lignin. Exploring the variations in these three macromolecules over time is crucial for understanding wood formation to enhance chemical processing and utilization. Here, we comprehensively analyzed the chemical composition of cell walls in the trunks of Pinus tabulaeformis using multiple techniques. In situ analysis showed that macromolecules accumulated gradually in the cell wall as the plant aged, and the distribution pattern of lignin was opposite that of polysaccharides, and both showed heterogenous distribution patterns. In addition, gel permeation chromatography (GPC) results revealed that the molecular weights of hemicelluloses decreased while that of lignin increased with age. Two-dimensional heteronuclear single quantum coherence nuclear magnetic resonance (2D-HSQC NMR) analysis indicated that hemicelluloses mainly comprised galactoglucomannan and arabinoglucuronoxylan, and the lignin types were mainly comprised guaiacyl (G) and p-hydroxyphenyl (H) units with three main linkage types: ß-O-4, ß-ß, and ß-5. Furthermore, the C-O bond (ß-O-4) signals of lignin decreased while the C-C bonds (ß-ß and ß-5) signals increased over time. Taken together, these findings shed light on wood formation in P. tabulaeformis and lay the foundation for enhancing the processing and use of wood and timber products.

Investigation of the resilience of cyclically actuated pine cone scales ofPinus jeffreyi.

The resilience of pine cone scales has been investigated in the context of current architectural efforts to develop bioinspired passive façade shading systems that can help regulate the indoor climate. As previously shown for other species, separated tissues ofPinus jeffreyipine cone scales show independent hygroscopic bending. The blocking force that pine cone scales can generate during a closing movement is shown to be affected by the length, width and mass of the scales. After cyclically actuating pine cone scales by submerging and drying them for 102 cycles and comparing their functional characteristics measured in the undamaged and damaged state, they were still able to achieve 97% of their undamaged blocking force and torque and over 94% of their undamaged opening angle. Despite evidence of cracking within the sclereid cell layer and extensive delamination of sclerenchyma fibres, no loss of function was observed in any tested pine cone scale. This functional resilience and robustness may allowP. jeffreyitrees to continue seed dispersal for longer periods of time and to reliably protect seeds that have not yet been released. These results have contributed to a better understanding of the pine cone scale and may provide inspiration for further improving the long-term performance of passive, hygro-sensitive façade shading systems.