Investigation of pulmonary inflammatory responses following intratracheal instillation of and inhalation exposure to polypropylene microplastics.

BACKGROUND: Microplastics have been detected in the atmosphere as well as in the ocean, and there is concern about their biological effects in the lungs. We conducted a short-term inhalation exposure and intratracheal instillation using rats to evaluate lung disorders related to microplastics. We conducted an inhalation exposure of polypropylene fine powder at a low concentration of 2 mg/m3 and a high concentration of 10 mg/m3 on 8-week-old male Fischer 344 rats for 6 h a day, 5 days a week for 4 weeks. We also conducted an intratracheal instillation of polypropylene at a low dose of 0.2 mg/rat and a high dose of 1.0 mg/rat on 12-week-old male Fischer 344 rats. Rats were dissected from 3 days to 6 months after both exposures, and bronchoalveolar lavage fluid (BALF) and lung tissue were collected to analyze lung inflammation and lung injury. RESULTS: Both exposures to polypropylene induced a persistent influx of inflammatory cells and expression of CINC-1, CINC-2, and MPO in BALF from 1 month after exposure. Genetic analysis showed a significant increase in inflammation-related factors for up to 6 months. The low concentration in the inhalation exposure of polypropylene also induced mild lung inflammation. CONCLUSION: These findings suggest that inhaled polypropylene, which is a microplastic, induces persistent lung inflammation and has the potential for lung disorder. Exposure to 2 mg/m3 induced inflammatory changes and was thought to be the Lowest Observed Adverse Effect Level (LOAEL) for acute effects of polypropylene. However, considering the concentration of microplastics in a real general environment, the risk of environmental hazards to humans may be low.

Microwave pyrolysis of polypropylene, and high-density polyethylene, and catalytic gasification of waste coffee pods to hydrogen-rich gas.

Plastic waste poses a critical environmental challenge for the world. The proliferation of waste plastic coffee pods exacerbates this issue. Traditional disposal methods such as incineration and landfills are environmentally unfriendly, necessitating the exploration of alternative management strategies. One promising avenue is the pyrolysis in-line reforming process, which converts plastic waste into hydrogen. However, traditional pyrolysis methods are costly due to inefficiencies and heat losses. To address this, for the first time, our study investigates the use of microwave to enhance the pyrolysis process. We explored microwave pyrolysis for polypropylene (PP), high-density polypropylene (HDPE), and waste coffee pods, with the latter primarily comprising polypropylene. Additionally, catalytic ex-situ pyrolysis of coffee pod pyrolysis over a nickel-based catalyst was investigated to convert the evolved gas into hydrogen. The single-stage microwave pyrolysis results revealed the highest gas yield at 500 °C for HDPE, and 41 % and 58 % (by mass) for waste coffee pods and polypropylene at 700 °C, respectively. Polypropylene exhibited the highest gaseous yield, suggesting its readiness for pyrolytic degradation. Waste coffee pods uniquely produced carbon dioxide and carbon monoxide gases because of the oxygen present in their structure. Catalytic reforming of evolved gas from waste coffee pods using a 5 % nickel loaded activated carbon catalyst, yielded 76 % (by volume) hydrogen at 900 °C. These observed results were supported by elemental balance analysis. These findings highlight that two-stage microwave and catalysis assisted pyrolysis could be a promising method for the efficient management of waste coffee pods, particularly for producing clean energy.

Behavioral impairments and disrupted mitochondrial energy metabolism induced by polypropylene microplastics in zebrafish larvae.

Polypropylene microplastics (PP-MPs) are emerging pollutant commonly detected in various environmental matrices and organisms, while their adverse effects and mechanisms are not well known. Here, zebrafish embryos were exposed to environmentally relevant concentrations of PP-MPs (0.08-50 mg/L) from 2 h post-fertilization (hpf) until 120 hpf. The results showed that the body weight was increased at 2 mg/L, heart rate was reduced at 0.08 and 10 mg/L, and behaviors were impaired at 0.4, 10 or 50 mg/L. Subsequently, transcriptomic analysis in the 0.4 and 50 mg/L PP-MPs treatment groups indicated potential inhibition on the glycolysis/gluconeogenesis and oxidative phosphorylation pathways. These findings were validated through alterations in multiple biomarkers related to glucose metabolism. Moreover, abnormal mitochondrial ultrastructures were observed in the intestine and liver in 0.4 and 50 mg/L PP-MPs treatment groups, accompanied by significant decreases in the activities of four mitochondrial electron transport chain complexes and ATP contents. Oxidative stress was also induced, as indicated by significantly increased ROS levels and significant reduced activities of CAT and SOD and GSH contents. All the results suggested that environmentally relevant concentrations of PP-MPs could induce disrupted mitochondrial energy metabolism in zebrafish, which may be associated with the observed behavioral impairments. This study will provide novel insights into PP-MPs-induced adverse effects and highlight need for further research.

Natural iron-containing minerals catalyze the degradation of polypropylene microplastics: a route to self-remediation learnt from the environment.

Virgin and environmentally aged polypropylene (PP) micropowders (V-PP and E-PP, respectively) were used as reference microplastics (MPs) in comparative photo- and thermo-oxidative ageing experiments performed on their mixtures with a natural ferrous sand (NS) and with a metal-free silica sand (QS). The ferrous NS was found to catalyze the photo-oxidative degradation of V-PP after both UV and simulated solar light irradiation. The catalytic activity in the V-PP/NS mixture was highlighted by the comparatively higher fraction of photo-oxidized PP extracted in dichloromethane, and the higher carbonyl index of the bulk polymer extracted with boiling xylene, when compared with the V-PP/QS mixture. Similarly, NS showed a catalytic effect on the thermal degradation (at T = 60 °C) of E-PP. The results obtained indicate that, under suitable environmental conditions (in this case, an iron-containing sediment or soil matrix, combined with simulated solar irradiation), the degradation of some types of MPs could be much faster than anticipated. Given the widespread presence of iron minerals (including the magnetite and iron-rich serpentine found in NS) in both coastal and mainland soils and sediments, a higher than expected resilience of the environment to the contamination by this class of pollutants is anticipated, and possible routes to remediation of polluted natural environments by eco-compatible iron-based minerals are envisaged.

A Recyclable Polypropylene Multilayer Film Maintaining the Quality and the Aroma of Coffee Pods during Their Shelf Life.

Films for coffee-pod packaging usually contain aluminium as an impermeable foil that is not recyclable and has to be discharged as waste. In this study, a recyclable polypropylene multilayer film is proposed as an alternative. The performance on the chemical composition of coffee was evaluated and compared to that of film containing aluminium (standard). The oxygen in the headspace, moisture, lipidic oxidation, and volatile organic compounds were studied in coffee pods during storage for 12 months at 25 and 40 °C. In addition, the acidity and acceptability of extracted coffee were evaluated. In the polypropylene-packaged pods, the percentage of oxygen during storage at 25 °C was lower than that in the standard. Moisture was not affected by the type of packaging materials. No differences were found between the peroxide values, except in pods stored for 3, 10, and 11 months at 25 °C, where they were even lower than the standard. Furans and pyrazines were the main volatile organic compounds detected. No differences were found in the pH and titratable acidity of the coffee brew either. All samples were well accepted by consumers without any perceived difference related to the packaging film. The polypropylene multilayer film is a sustainable recyclable material with high performance, in particular, against oxygen permeation.

Selective recovery of pyrolyzates of biodegradable (PLA, PHBH) and common plastics (HDPE, PP, PS) during co-pyrolysis under slow heating.

Pyrolytic synergistic interactions, in which the production of pyrolyzates is enhanced or inhibited, commonly occur during the co-pyrolysis of different polymeric materials, such as plastics and biomass. Although these interactions can increase the yield of desired pyrolysis products under controlled degradation conditions, the desired compounds must be separated from complex pyrolyzates and further purified. To balance these dual effects, this study was aimed at examining pyrolytic synergistic interactions during slow heating co-pyrolysis of biodegradable plastics including polylactic acid (PLA) and poly(3-hydroxybutyrate-co-3-hydroxyhexaoate) (PHBH) and petroleum-based plastics including high-density polyethylene (HDPE), polypropylene (PP), and polystyrene (PS). Comprehensive investigations based on thermogravimetric analysis, pyrolysis-gas chromatography/mass spectrometry, and evolved gas analysis-mass spectrometry revealed that PLA and PHBH decompose at lower temperatures (273-378 °C) than HDPE, PP, and PS (386-499 °C), with each polymer undergoing independent decomposition without any pyrolytic interactions. Thus, the independent pyrolysis of biodegradable plastics, such as PLA and PHBH, with common plastics, such as HDPE, PP, and PS, can theoretically be realized through temperature control, enabling the selective recovery of their pyrolyzates in different temperature ranges. Thus, pyrolytic approaches can facilitate the treatment of mixed biodegradable and common plastics.

The Impact of Virgin and Aged Microstructured Plastics on Proteins: The Case of Hemoglobin Adsorption and Oxygenation.

Plastic particles, particularly micro- and nanoparticles, are emerging pollutants due to the ever-growing amount of plastics produced across a wide variety of sectors. When plastic particles enter a biological medium, they become surrounded by a corona, giving them their biological identity and determining their interactions in the living environment and their biological effects. Here, we studied the interactions of microstructured plastics with hemoglobin (Hb). Virgin polyethylene microparticles (PEMPs) and polypropylene microparticles (PPMPs) as well as heat- or irradiation-aged microparticles (ag-PEMPs and ag-PPMPs) were used to quantify Hb adsorption. Polypropylene filters (PP-filters) were used to measure the oxygenation of adsorbed Hb. Microstructured plastics were characterized using optical microscopy, SAXS, ATR-FTIR, XPS, and Raman spectroscopy. Adsorption isotherms showed that the Hb corona thickness is larger on PPMPs than on PEMPs and Hb has a higher affinity for PPMPs than for PEMPs. Hb had a lower affinity for ag-PEMPs and ag-PPMPs, but they can be adsorbed in larger amounts. The presence of partial charges on the plastic surface and the oxidation rate of microplastics may explain these differences. Tonometry experiments using an original method, the diffuse reflection of light, showed that adsorbed Hb on PP-filters retains its cooperativity, but its affinity for O2 decreases significantly.

Mechanistic insight into microbial interaction and metabolic pattern of anammox consortia on surface-modified biofilm carrier with extracellular polymeric substances.

The extremely slow growth rate of anaerobic ammonia oxidation (anammox) bacteria limits full-scale application of anammox process worldwide. In this study, extracellular polymeric substances (EPS)-coated polypropylene (PP) carriers were prepared for biofilm formation. The biomass adhesion rate of EPS-PP carrier was 12 times that of PP carrier, and EPS-PP achieved significant enrichment of E. coli BY63. The 120-day continuous flow experiment showed that the EPS-PP carrier accelerated the formation of anammox biofilm, and the nitrogen removal efficiency increased by 10.5 %. In addition, the abundance of Candidatus Kuenenia in EPS-PP biofilm was 27.1%. Simultaneously, amino acids with high synthesis cost and the metabolites of glycerophospholipids related to biofilm formation on EPS-PP biofilm were significantly up-regulated. Therefore, EPS-PP carriers facilitated the rapid formation of anammox biofilm and promoted the metabolic activity of functional bacteria, which further contributed to the environmental and economic sustainability of anammox process.

Py-GC-MS analysis for microplastics: Unlocking matrix challenges and sample recovery when analyzing wastewater for polypropylene and polystyrene.

Matrix interference and recovery when using pyrolysis gas chromatography (Py-GC-MS) to analyze wastewater for polystyrene (PS) and polypropylene (PP) microplastics (MP) was studied. Raw wastewater underwent a sample preparation train commonly applied for such matrix. The train consisted of six discrete steps to reduce the organic matter content without affecting MP in the sample. One large wastewater sample was collected, homogenized, and subdivided into 21 subsamples. Three samples were analyzed without further sample preparation. The remaining samples were divided in sets of three, and each set underwent an increasing number of steps of the procedure, up to the last set, which underwent the full treatment. The matrix effect on the determination of PS and PP was statistically evaluated by comparing in-matrix and external calibration curves at each step. Recovery of MP was assessed after each step by adding deuterated PS to the samples. A main finding was that there was no significant matrix effect for these polymers throughout the preparation train, suggesting that matrix components did not interfere with the analytical method. However, a significant loss of polymer mass was found between the steps, which may result in MPs falling below detection limits. Therefore, Py-GC-MS could be used for MP quantification before analysis by other techniques which require more extensive matrix removal. A downside of this approach is that analyzing such samples without matrix reduction will increase the need for instrumental maintenance.

Fabric structure and polymer composition as key contributors to micro(nano)plastic contamination in face masks.

The surge in face mask use due to COVID-19 has raised concerns about micro(nano)plastics (MNPs) from masks. Herein, focusing on fabric structure and polymer composition, we investigated MNP generation characteristics, mechanisms, and potential risks of surgical polypropylene (PP) and fashionable polyurethane (PU) masks during their wearing and photoaging based on stereomicroscope, µ-Fourier transform infrared spectroscopy (µ-FTIR), and scanning electron microscope (SEM) techniques. Compared with new PP and PU masks (66 ± 16 MPs/PP-mask, 163 ± 83 MPs/PU-mask), single- and multiple-used masks exhibited remarkably increased MP type and abundance (600-1867 MPs/PP-mask, 607-2167 MPs/PU-mask). Disinfection exacerbated endogenous MP generation in masks, with washing (416 MPs/PP-mask, 30,708 MPs/PU-mask) being the most prominent compared to autoclaving (219 MPs/PP-mask, 553 MPs/PU-mask) and alcohol spray (162 MPs/PP-mask, 18,333 MPs/PU-mask). Photoaging led to massive generation of MPs (8.8 × 104-3.7 × 105 MPs/PP-layer, 1.0 × 105 MPs/PU-layer) and NPs (5.2 × 109-3.6 × 1013 NPs/PP-layer, 3.5 × 1012 NPs/PU-layer) from masks, presenting highly fabric structure-dependent aging modes as "fragmentation" for fine fiber-structure PP mask and "erosion" for 3D mesh-structure PU mask. The MNPs derived from PP/PU mask caused significant deformities of Zebrafish (Danio rerio) larvae. These findings underscore the potential adverse effects of masks on humans and aquatic organisms, advocating to enhance proper use and rational disposal for masks.

Mechanical performance and anisotropic analysis of rubberised 3D-printed concrete incorporating PP fibre.

The research investigates the effects of substituting sand with rubber particles derived from waste tyres-up to 40% by volume-and the inclusion of polypropylene (PP) fibres. Unlike steel fibres, which can cause operational challenges and surface irregularities in the printing process, PP fibres' flexibility integrates well within the concrete matrix. This integration ensures smooth extrusion and a high-quality surface finish, enhancing the printability of the concrete. The study's findings reveal that including rubber particles and PP fibres impacts the concrete's properties, showing a general decline in compressive and flexural strengths as the rubber content increases. Nevertheless, the PP fibre-enhanced mixtures maintain sufficient structural strength, demonstrating an anisotropic compressive strength above 30 MPa and a flexural strength of 4 MPa. These results underscore the feasibility of using rubberised 3D-printed concrete with PP fibres in sustainable construction practices, aligning with standards (ACI 318:2018) and contributing to eco-friendly and innovative construction methodologies.

Hydrological response and crack resistance of polypropylene-fiber reinforced compacted steel slag-bentonite mixtures under wetting-drying cycles.

Desiccation-induced cracks in a compacted clay liner significantly deteriorate the hydraulic barrier performance of landfill covers. The present study explores the effects of polypropylene (PP) fiber reinforcement on the hydrological response and crack resistance of compacted steel slag (SS; 90 wt%) - bentonite (10 wt%) mixtures under drying and wetting cycles. Comprehensive tests were conducted to explore the impact of different fiber lengths (6-12 mm) and contents (0-0.4 % wt.%), including hydraulic conductivity tests for measuring the saturated hydraulic conductivity (ks), unconfined-penetration tests for measuring the tensile strength, small-sized plate tests for quantifying crack development, and large-sized bucket tests for studying the hydrological response and crack characteristics. Higher fiber contents and longer fiber lengths increased the ks-value of the specimens. For a 0.3 % fiber content, the tensile strength peaked for the 9-mm fiber. Consistently, the specimen reinforced with the 9-mm fibers exhibited significantly fewer cracks than those reinforced with the 6-mm and 12-mm fibers. It was because the 6-mm fibers had a shorter anchorage length, while the 12-mm fibers tended to agglomerate. The large-sized bucket tests showed that fiber reinforcement limited crack development significantly under wetting and drying cycles, reducing the rainfall infiltration by 40 % and enhancing the soil water retention capacity. Finally, a 0.3 wt% of 9-mm PP was recommended to reinforce the compacted SS-bentonite mixtures.

Charting the microplastic menace: A bibliometric analysis of pollution in Malaysian mangroves and polypropylene bioaccumulation assessment in Anadara granosa.

According to a bibliometric analysis, studies on microplastic pollution in Malaysia are still incomprehensive. This study found microplastic contamination in sediment (97 particles/kg) and water (10,963 particles/m3) samples from Malaysian mangroves. Sediment from Matang and water from Kuala Selangor recorded the highest microplastic concentrations at 140 ± 5.13 particles/kg and 13,350 ± 37.95 particles/m3, respectively. Fragmented, blue, rayon and particles of <0.1 mm microplastic were the most abundant in sediment and water. In an experiment of polypropylene microplastic uptakes, Anadara granosa was found to uptake more 0.1 mm fiber particles. The uptake is strongly correlated to the presence of microplastics in sediment and water. The estimated dietary intake (EDI) indicates that a consumer could ingest 507 microplastic particles/year by consuming contaminated A. granosa. Therefore, mitigating measures are crucial to safeguard aquatic systems and humans from microplastic pollution.

Safe(r)-by-design principles in the thermoplastics industry: guidance on release assessment during manufacture of nano-enabled products.

Background: The application of nanomaterials (NMs) and nano-enabled products (NEPs) across many industries has been extensive and is still expanding decades after first being identified as an emerging technology. Additive manufacturing has been greatly impacted and has seen the benefits of integrating NMs within products. With the expansion of nanotechnology, there has been a need to develop more adaptive and responsive methods to ascertain risks and ensure technology is developed safely. The Safe(r)-by-Design (SbD) concept can be used to establish safe parameters and minimise risks during the materials' lifecycle, including the early stages of the supply chain. Exposure monitoring has advanced in recent years with the creation of standardised protocols for occupational exposure assessment of nano-objects and their aggregates and agglomerates (NOAA). Methods: To aid in the development of an online SbD-supporting platform by the EU-funded project SAbyNA, we adopt a Europe Standard for monitoring release of NOAA to identify if a greater release of NOAA is associated with incorporation of NMs within NEPs compared to a polymer matrix alone. Case studies included filaments of polypropylene (PP) with nano-Ag or polycarbonate (PC) with single-walled carbon nanotubes (SWCNTs). NMs were received in masterbatch, and therefore previously modified to align with SbD interventions. Results were collected in line with European Standard recommendations: monitoring particle concentrations using direct reading instruments (DRI), sampling for offline chemical and morphological analysis, and collecting contextual information. Results and discussion: Based on the criteria described in the European standard (BS EN 17058), data from both case studies identified that inhalation exposure relating to NM was "unlikely". Despite this, during the production of the SWCNT-PC filaments, some noteworthy observations were made, including several DRI activity measurements shown to be higher than background levels, and material morphologically similar to the reference SWCNT/polymeric masterbatch observed in offline analysis. The data collected during this campaign were used to discuss choices available for data interpretation and decision-making in the European Standard for monitoring release of NOAA and also to facilitate the development of SAbyNA's user-friendly industry platform for the SbD of NMs and NEPs.

Carbon nanotubes synthesis over coal ash based catalysts using polypropylene waste via CVD process: Influence of catalyst and reaction temperature.

Coal ash containing significant amount of SiO2 and Al2O3 is utilized as a catalyst substrate for carbon nanotubes (CNTs) synthesis. Three different types of catalysts were made by impregnating coal ash with cobalt, iron, and nickel. These catalysts were used to produce CNTs through pyrolysis of waste polypropylene followed by chemical vapor deposition. The influence of catalyst type and reaction temperature (700, 800 and 900 °C) on CNTs yield and its quality was studied in detail. The produced CNTs were characterized by thermogravimetric analysis (TGA), Raman scattering and electron microscopes (FESEM and HRTEM). The TGA results revealed that the Ni catalyst produced CNTs with highest yield (266 %) compared to those synthesized over and Fe (96 %) and Co (95 %). However, the yield of the CNTs from all three metal impregnated coal ash based catalysts was found to have decreased with increase in reaction temperature. The thermal stability of CNTs obtained over different catalysts followed the order of Fe (570 °C) > Ni (550 °C) > Co (530 °C). Further, the Raman analysis demonstrated that the produced CNTs over different catalysts showed increasing degree of graphitization with the rise in reaction temperature. Additionally, the ID/IG ratios indicated that CNTs produced from Fe catalyst showed highest degree of graphitization followed by Co and Ni. FESEM and HRTEM analysis showed that the coal ash based catalysts produced multiwalled CNTs and the diameter of the CNTs was increasing with the rise in catalysis temperature. Therefore, co-utilization of coal ash and waste plastic for production of high value CNTs can be a sustainable approach to waste management while actively contributing in circular economy.

Biodegradation of polystyrene (PS) and polypropylene (PP) by deep-sea psychrophilic bacteria of Pseudoalteromonas in accompany with simultaneous release of microplastics and nanoplastics.

Plastics dumped in the environment are fragmented into microplastics by various factors (UV, weathering, mechanical abrasion, animal chewing, etc.). However, little is known about plastic fragmentation and degradation mediated by deep-sea microflora. To obtain deep-sea bacteria that can degrade plastics, we enriched in situ for 1 year in the Western Pacific using PS as a carbon source. Subsequently, two deep-sea prevalent bacteria of the genus Pseudoalteromonas (Pseudoalteromonas lipolytica and Pseudoalteromonas tetraodonis) were isolated after 6 months enrichment in the laboratory under low temperature (15 °C). Both showed the ability to degrade polystyrene (PS) and polypropylene (PP), and biodegradation accelerated the generation of micro- and nanoplastics. Plastic biodegradation was evidenced by the formation of carboxyl and carboxylic acid groups, heat resistance decrease and plastic weight loss. After 80 days incubation at 15 °C, the microplastic concentration of PS and PP could be up to 1.94 × 107/L and 5.83 × 107/L, respectively, and the proportion of nanoplastics (< 1 µm) could be up to 65.8 % and 73.6 %. The film weight loss were 5.4 % and 4.5 % of the PS films, and 2.3 % and 1.8 % of the PP films by P. lipolytica and P. tetraodonis, respectively; thus after discounting the weight loss of microplastics, the only 3.9 % and 2.8 % of the PS films, and 1.3 % and 0.7 % of the PP films, respectively, were truly degraded by the two bacteria respectively after 80 days of incubation. This study highlights the role of Pseudoalteromonas in fragmentation and degradation of plastics in cold dark pelagic deep sea.

Efficacy of using adipose-derived stem cells and PRP on regeneration of 40 -mm long sciatic nerve defect bridged by polyglycolic-polypropylene mesh in canine model.

BACKGROUND: Sciatic nerve repair becomes a focus of research in neurological aspect to restore the normal physical ability of the animal to stand and walk. Tissue engineered nerve grafts (TENGs) provide a promising alternative therapy for regeneration of large gap defects. The present study investigates the regenerative capacity of PRP, ADSCs, and PRP mixed ADSCs on a long sciatic nerve defect (40-mm) bridged by a polyglycolic polypropylene (PGA-PRL) mesh which acts as a neural scaffold. MATERIALS AND METHODS: The study was conducted on 12 adult male mongrel dogs that were randomly divided into 4 groups: Group I (scaffold group); where the sciatic defect was bridged by a (PGA-PRL) mesh only while the mesh was injected with ADSCs in Group II (ADSCs group), PRP in Group III (PRP group). Mixture of PRP and ADSCs was allocated in Group IV (PRP + ADSCs group). Monthly, all animals were monitored for improvement in their gait and a numerical lameness score was recorded for all groups. 6 months-post surgery, the structural and functional recovery of sciatic nerve was evaluated electrophysiologically, and on the level of gene expression, and both sciatic nerve and the gastrocnemius muscle were evaluated morphometrically, histopathologically. RESULTS: Numerical lameness score showed improvement in the motor activities of both Group II and Group III followed by Group IV and the scaffold group showed mild improvement even after 6 months. Histopathologically, all treated groups showed axonal sprouting and numerous regenerated fascicles with obvious angiogenesis in proximal cut, and distal portion where Group IV exhibited a significant remyelination with the MCOOL technique. The regenerative ratio of gastrocnemius muscle was 23.81%, 56.68%, 52.06% and 40.69% for Group I, II, III and IV; respectively. The expression of NGF showed significant up regulation in the proximal portion for both Group III and Group IV (P ≤ 0.0001) while Group II showed no significant difference. PDGF-A, and VEGF expressions were up-regulated in Group II, III, and IV whereas Group I showed significant down-regulation for NGF, PDGF-A, and VEGF (P ≤ 0.0001). CONCLUSION: ADSCs have a great role in restoring the damaged nerve fibers by secreting several types of growth factors like NGF that have a proliferative effect on Schwann cells and their migration. In addition, PRP therapy potentiates the effect of ADSCs by synthesis another growth factors such as PDGF-A, VEGF, NGF for better healing of large sciatic gap defects.

[Whole Process Analysis and Fate Behavior of Microplastics in Urban Wastewater Treatment Plants, Including their Occurrence Forms, Components, and Removal Efficiency].

Microplastics are among the most difficult new pollutants to remove in wastewater treatment plants. In order to explore the occurrence form, size distribution, composition, removal efficiency, migration law, and fate behavior characteristics of microplastic particles in sewage plants, taking a sewage treatment plant in Hohhot as an example, a total of 17 sampling sites were set up. The LAS X software counted the shape, abundance, and size of microplastics and conducted a full-process analysis. The results showed that： fibrous microplastics had the highest abundance and widest distribution and were the main form of existence, accounting for 61.8% of the total abundance； the size of microplastics ranged mainly between 0 and 1.00 mm, and among the four sizes, the abundance of microplastics 0.25 to 0.50 mm in China was the highest, accounting for 32.9%. Among the eight types of plastic components detected, polyester substances （PET, PBT）, cellulose, and polypropylene （PP） were the main components, accounting for 25%, 21%, and 17%, respectively. The influent abundance of the sewage plant was （73 ±5） n·L-1, the effluent abundance was （14 ±2） n·L-1, and the overall removal rate was （80.8 ±12.1）%. Among the three treatment stages of the sewage plant, only the primary treatment played a role in removal, and the abundance of microplastics surged in the secondary treatment. Different structures playing a major role in the removal of microplastics were fine grids （49.2 ±7.4）% and secondary sedimentation tanks （92.4 ±13.9）%. Microplastics mainly existed in the form of fibers, fragments, and films. The proportion of fibers was approximately 70%, and the size of fragments was mainly concentrated between 0.50 and 5.00 mm. Most fragments were in the range of 5.00 mm, accounting for 50%, making them the main form apart from fibrous. The film-like size was mostly concentrated in the range of less than 0.50 mm, accounting for more than 10%. Therefore, improving the removal of small-sized fibrous and film-like microplastics and large-sized fragmented microplastic particles can effectively reduce the pollution risk of microplastics in the environment caused by sewage plant drainage.

Effects of different mesh materials on complications after prophylactic placement for stoma formation: a systematic review and network meta-analysis.

PURPOSE: We primary aimed to synthesise the available data, assess the effectiveness of different mesh materials in prophylactic mesh placement, and rank these materials according to the incidence of parastomal hernia (PSH) and other stoma complications. METHOD: This network meta-analysis performed a systematic review and meta-analysis according to the Preferred Reporting Items for Systematic Review and Meta-Analysis statement. Four databases were searched for randomised controlled trials of prophylactic mesh placement. The aggregated results were performed in the STATA routine for Bayesian hierarchical random effects models. RESULT: Thirteen randomised controlled trials from 1203 articles, met the inclusion criteria, including 681 cases without meshes, 65 cases with mesh material of xenogeneic acellular dermis (porcine/bovine), 27 cases with polypropylene/PG910, 114 cases with polypropylene/polyglecaprone (Monocryl), 117 cases with polypropylene/cellulose (ORC), 233 cases with polypropylene, and 35 cases with polypropylene/PVDF. In network A, compared with no mesh, only polypropylene (RR 0.24, 95% CI 0.04-0.80) were significantly associated with a reduction in the incidence of PSH. In network B, no statistical difference regarding stoma complications was found between mesh and no mesh. CONCLUSION: Based on the network meta-analysis and ranking results, the polypropylene mesh material exhibited the best performance. However, this conclusion needs to be confirmed with larger sample sizes and high-quality randomised controlled trials.

The effects of methylparaben exposure on biofilm tolerance to chlorine disinfection.

Parabens are emerging contaminants that have been detected in drinking water. Their presence in DW distribution systems (DWDS) can alter bacterial behaviour, characteristics, and structure, which may compromise DW disinfection. This work provides insights into the impact of methylparaben (MP) on the tolerance to chlorine disinfection and antibiotics from dual-species biofilms formed by Acinetobacter calcoaceticus and Stenotrophomonas maltophilia isolated from DW and grown on high-density polyethylene (HDPE) and polypropylene (PPL). Results showed that dual-species biofilms grown on PPL were more tolerant to chlorine disinfection, expressing a decrease of over 50 % in logarithmic reduction values of culturable cells in relation to non-exposed biofilms. However, bacterial tolerance to antibiotics was not affected by MP presence. Although MP-exposed dual-species biofilms grown on HDPE and PPL were metabolically more active than non-exposed counterparts, HDPE seems to be the material with lower impact on DW risk management and disinfection, if MP is present. Overall, results suggest that MP presence in DW may compromise chlorine disinfection, and consequently affect DW quality and stability, raising potential public health issues.