A microfluidic biosensor for the diagnosis of chronic wasting disease.

Cervids are affected by a neurologic disease that is always fatal to individuals and has population effects. This disease is called chronic wasting disease (CWD) and is caused by a misfolded prion protein. The disease is transmitted via contact with contaminated body fluids and tissue or exposure to the environment, such as drinking water or food. Current CWD diagnosis depends on ELISA screening of cervid lymph nodes and subsequent immunohistochemistry (IHC) confirmation of ELISA-positive results. The disease has proven to be difficult to control in part because of sensitivity and specificity issues with the current test regimen. We have investigated an accurate, rapid, and low-cost microfluidic microelectromechanical system (MEMS) biosensing device for the detection of CWD pathologic prions in retropharyngeal lymph nodes (RLNs), which is the current standard type of CWD diagnostic sample. The device consists of three novel regions for concentrating, trapping, and detecting the prion. The detection region includes an array of electrodes coated with a monoclonal antibody against pathologic prions. The experimental conditions were optimized using an engineered prion control antigen. Testing could be completed in less than 1 hour with high sensitivity and selectivity. The biosensor detected the engineered prion antigen at a 1:24 dilution, while ELISA detected the same antigen at a 1:8 dilution. The relative limit of detection (rLOD) of the biosensor was a 1:1000 dilution of a known strong positive RLN sample, whereas ELISA showed a rLOD of 1:100 dilution. Thus, the biosensor was 10 times more sensitive than ELISA, which is the currently approved CWD diagnostic test. The biosensor's specificity and selectivity were confirmed using known negative RPLN samples, a negative control antibody (monoclonal antibody against bovine coronavirus BCV), and two negative control antigens (bluetongue virus and Epizootic hemorrhagic disease virus). The biosensor's ability to detect pathogenic prions was verified by testing proteinase-digested positive RLN samples.

A microfluidic biosensor architecture for the rapid detection of COVID-19.

The lack of enough diagnostic capacity to detect severe acute respiratory syndrome coronavirus 2 (SARS-COV-2) has been one of the major challenges in the control the 2019 COVID pandemic; this led to significant delay in prompt treatment of COVID-19 patients or accurately estimate disease situation. Current methods for the diagnosis of SARS-COV-2 infection on clinical specimens (e.g. nasal swabs) include polymerase chain reaction (PCR) based methods, such as real-time reverse transcription (rRT) PCR, real-time reverse transcription loop-mediated isothermal amplification (rRT-LAMP), and immunoassay based methods, such as rapid antigen test (RAT). These conventional PCR methods excel in sensitivity and specificity but require a laboratory setting and typically take up to 6 h to obtain the results whereas RAT has a low sensitivity (typically at least 3000 TCID50/ml) although with the results with 15 min. We have developed a robust micro-electro-mechanical system (MEMS) based impedance biosensor fit for rapid and accurate detection of SARS-COV-2 of clinical samples in the field with minimal training. The biosensor consisted of three regions that enabled concentrating, trapping, and sensing the virus present in low quantities with high selectivity and sensitivity in 40 min using an electrode coated with a specific SARS-COV-2 antibody cross-linker mixture. Changes in the impedance value due to the binding of the SARS-COV-2 antigen to the antibody will indicate positive or negative result. The testing results showed that the biosensor's limit of detection (LoD) for detection of inactivated SARS-COV-2 antigen in phosphate buffer saline (PBS) was as low as 50 TCID50/ml. The biosensor specificity was confirmed using the influenza virus while the selectivity was confirmed using influenza polyclonal sera. Overall, the results showed that the biosensor is able to detect SARS-COV-2 in clinical samples (swabs) in 40 min with a sensitivity of 26 TCID50/ml.

Uncooled two-microbolometer stack for long wavelength infrared detection.

We have investigated an uncooled infrared (IR) detector utilizing a dual level architecture. This was achieved by combining two-microbolometer stack in the vertical direction to achieve high IR absorption over two distinct spectral windows across the long wavelength infrared region (LWIR). In addition, we have studied amorphous silicon germanium oxide (SixGeyO1-x-y) as an IR sensitive material, and metasurface to control IR absorption/reflection in interaction with standard Fabry-Perot cavity. The bottom microbolometer uses a metasurface to selectively absorbs a portion of the spectrum and reflects radiation outside this window range. At the same time, the top microbolometer uses a conventional Fabry-Perot resonant cavity to absorb a different portion of the spectrum and transmit any unabsorbed radiation outside this window. This device can be used to measure the absolute temperature of an object by comparing the relative signals in the two spectral bands. The spectral responsivity and detectivity, and thermal response time were > 105 V/W, > 108 cm Hz1/2/W, and 1.13 ms to filtered blackbody infrared radiation between (2-16) µm. The microbolometer voltage noise power spectral density was reduced by annealing the microbolometers in vacuum at 300 °C.

A microfluidic biosensor for rapid simultaneous detection of waterborne pathogens.

A microfluidic based biosensor was investigated for rapid and simultaneous detection of Salmonella, Legionella, and Escherichia coli O157:H7 in tap water and wastewater. The biosensor consisted of two sets of focusing electrodes connected in parallel and three sets of interdigitated electrodes (IDE) arrays. The electrodes enabled the biosensor to concentrate and detect bacteria at both low and high concentrations. The focusing region was designed with vertical metal sidewall pairs and multiple tilted thin-film finger pairs to generate positive dielectrophoresis (p-DEP) to force the bacteria moving toward the microchannel centerline. As a result, the bacterial pathogens were highly concentrated when they reached the detection electrode arrays. The detection IDE arrays were coated with three different antibodies against the target bacterial pathogens and a cross-linker to enhance the binding of antibodies to the detection electrode. As the binding of bacterial pathogen to its specific antibodies took place, the impedance value changed. The results demonstrated that the biosensors were capable of detecting Salmonella, Legionella, and E. coli 0157:H7 simultaneously with a detection limit of 3 bacterial cells/ml in 30 - 40 min.

An impedance biosensor for simultaneous detection of low concentration of Salmonella serogroups in poultry and fresh produce samples.

This paper reports the design, fabrication and testing of a microfluidic based impedance biosensor for rapid and simultaneous detection of three Salmonella serogroups. The microfluidic device consists of three microchannels, each one includes a region for focusing the Salmonella cells into the centerline of the microchannel and direct them toward the sensing region to obtain highly concentrated samples using positive dielectrophoresis force. A region for bacteria sensing consists of interdigitated electrode (IDE) array with 10 pairs of fingers. Three types of Salmonella antibodies (type B, D and E) were mixed separately with the cross-linker (Sulfo-LC-SPDP) to enhance the immobalization of the antibodies to the detection electrodes. The electrode surfaces was then functionalized with the three mixtures, one for each channel. As target antigen binds to the antibody, it results in impedance change. The Salmonella samples were spiked with Salmonella type B, introduced into the biosensor via the sample inlet into the focusing region, and then toward the sensing region where they bind to the immobilized antibody, causing a change in the impedance. The performance of the devices was tested using single Salmonella serotype B and two Salmonella serotypes B, and D, with a limit of detection of 7 cells/ml. The biosensor was also able to differentiate live from dead bacteria eliminating the false positive results. Finally, the device was also able to detect Salmonella selectively when other type of pathogen was present.

Microfluidic based impedance biosensor for pathogens detection in food products.

A MEMS-based impedance biosensor was designed, fabricated, and tested to effectively detect the presence of bacterial cells including E. coli O157:H7 and Salmonella typhimurium in raw chicken products using detection region made of multiple interdigitated electrode arrays. A positive dielectrophoresis based focusing electrode was used in order to focus and concentrate the bacterial cells at the centerline of the fluidic microchannel and direct them toward the detection microchannel. The biosensor was fabricated using surface micromachining technology on a glass substrate. The results demonstrate that the device can detect Salmonella with concentrations as low as 10 cells/mL in less than 1 h. The device sensitivity was improved by the addition of the focusing electrodes, which increased the signal response by a factor between 6 and 18 times higher than without the use of the focusing electrodes. The biosensor is selective and can detect other types of pathogen by changing the type of the antibody immobilized on the detection electrodes. The device was able to differentiate live from dead bacteria.

An integrated impedance biosensor platform for detection of pathogens in poultry products.

This paper presents an impedance-based biosensor for rapid and simultaneous detection of Salmonella serotypes B, D, and E with very low concentration. The biosensor consists of a focusing region, and three detection regions. The cells focusing was achieved using a ramp down electroplated vertical electrode pair along with tilted thin film finger pairs that generate p-DEP forces to focus and concentrate the bacterial cells into the center of the microchannel, and direct them toward the detection region. The detection regions consist of three interdigitated electrode arrays (IDEA), each with 20 pairs of finger coated with a mixture of anti-Salmonella antibody and crosslinker to enhance the adhesion to IDEA. The impedance changes as the target Salmonella binds to the antibody. The biosensor has showed excellent performance as proven by the detection of a single Salmonella serotype B, and simultaneous detection of two Salmonella serotypes B and D with a limit of detection (LOD) of 8 Cells/ml in ready-to-eat turkey samples, the addition of focusing capability improved the measured signal by a factor of between 4-4.5, the total detection time of 45 minutes, selectivity of the sensor on different types of bacterial cells, and the ability to distinguish between dead and live cells.

Low concentration E. coli O157:H7 bacteria sensing using microfluidic MEMS biosensor.

This paper reports the design, fabrication, and testing of a microfluidic MEMS biosensor for rapid sensing of low concentration Escherichia coli O157:H7. It consists of a specially designed focusing and sensing region, which enables the biosensor to detect low concentration of bacterial cells. The focusing region consists of a ramped vertical electrode pair made of electroplated gold along with tilted thin film finger pairs (45°) embedded inside a microchannel. The focusing region generates positive dielectrophoresis force, which moves the cells towards the edges of the tilted thin film electrode fingers, located at the center of the microchannel. The fluidic drag force then carries the focused cells to the sensing region, where three interdigitated electrode arrays (IDEAs) with 30, 20, and 10 pairs, respectively, are embedded inside the microchannel. This technique resulted in highly concentrated samples in the sensing region. The sensing IDEAs are functionalized with the anti-E. coli antibody for specific sensing of E. coli 0157:H7. As E. coli binds to the antibody, it results in an impedance change, which is measured across a wide frequency range of 100 Hz-10 MHz. The biosensor was fabricated on a glass substrate using the SU8 epoxy resist to form the microchannel, gold electroplating to form the vertical focusing electrode pair, a thin gold film to form the sensing electrode, the finger electrodes, traces and bonding pads, and polydimethylsiloxane to seal the device. The microfluidic impedance biosensor was tested with various low concentration bacterial samples and was able to detect bacterial concentration, as low as 39 CFU/ml with a total sensing time of 2 h.