Three-dimensional force-tactile sensors based on embedded fiber Bragg gratings in anisotropic materials.

Three-dimensional force-tactile sensors have attracted much attention for their great potential in the applications of human-computer interaction and bionic intelligent robotics. Herein, a flexible haptic sensor based on dual fiber Bragg gratings (FBGs) embedded in a bionic anisotropic material is proposed for the detection of 3D forces. To achieve the discrimination of normal and tangential force angles and magnitudes, FBGs were orthogonally embedded in a flexible silicone cylinder for force determination. Fe3O4 nanoparticles were used as a modifying agent to induce anisotropic elasticity of the silicone structure to improve the angle detection resolution. The results show that the flexible tactile sensor can detect the angle and magnitude of the 3D force.

Dual Regime Mode-Locked and Q-Switched Erbium-Doped Fiber Laser by Employing Graphene Filament-Chitin Film-Based Passive Saturable Absorber.

We investigate the dynamics of high energy dual regime unidirectional Erbium-doped fiber laser in ring cavity, which is passively Q-switched and mode-locked through the use of an environmentally friendly graphene filament-chitin film-based saturable absorber. The graphene-chitin passive saturable absorber allows the option for different operating regimes of the laser by simple adjustment of the input pump power, yielding, simultaneously, highly stable and high energy Q-switched pulses at 82.08 nJ and 1.08 ps mode-locked pulses. The finding can have applications in a multitude of fields due to its versatility and the regime of operation that is on demand.

Compact Harmonic Vernier Sensor Based on an In-Fiber FPI with Three Reflector System for Simultaneous Gas Pressure and Temperature Measurement.

In this work, we proposed a sensitivity-enhanced temperature sensor, a compact harmonic Vernier sensor based on an in-fiber Fabry-Perot Interferometer (FPI), with three reflective interfaces for the measurement of gas temperature and pressure. FPI consists of air and silica cavities formulated by single-mode optical fiber (SMF) and several short hollow core fiber segments. One of the cavity lengths is deliberately made larger to excite several harmonics of the Vernier effect that have different sensitivity magnifications to the gas pressure and temperature. The spectral curve could be demodulated using a digital bandpass filter to extract the interference spectrum according to the spatial frequencies of resonance cavities. The findings indicate that the material and structural properties of the resonance cavities have an impact on the respective temperature sensitivity and pressure sensitivity. The measured pressure sensitivity and temperature sensitivity of the proposed sensor are 114 nm/MPa and 176 pm/°C, respectively. Therefore, the proposed sensor combines ease of fabrication and high sensitivity, making it great potential for practical sensing measurements.

Development of polarization modulator using MXene thin film.

In this work, polarization modulator utilizing MXene material, namely Nb2C is demonstrated. S band signal is injected into Nb2C thin film and is modulated by 1400 nm laser diode. A total of 39.81° of polarization rotation is attained when the pump power is increased to 223 mW. The rotation of light is due to thermo-optic effect. The efficiency of polarization modulator is calculated at 0.1974°/mW.

Generation of mode-locked pulses based on D-shaped fiber with CdTe as a saturable absorber in the C-band region.

This study demonstrates the potential of cadmium telluride (CdTe), a part of the quantum dot (QD) family, as a saturable absorber (SA) to generate ultrashort pulses at the C-band region. The SA was fabricated by drop-casting the CdTe material onto the exposed core of the D-shaped fiber. The nonlinear property of the fabricated SA has a modulation depth of 1.87% and saturation intensity of 6.0 kW cm-2. The mode-locked laser was generated after the SA was integrated into the erbium-doped fiber laser (EDFL) cavity at a threshold pump power of 192.1 mW giving a center wavelength of 1559 nm and a pulse duration of 770 fs. The maximum average output and peak power were measured to be 2.8 mW and 0.208 kW, respectively. The mode-locked fiber laser generated a signal-to-noise ratio (SNR) of 67.7 dB, proving that the generated mode-locked pulses were very stable. The current work indicates that the novel CdTe device can provide stable mode-locked lasers in the C-band region.

Polarization response of planarized optical waveguides to determine the anisotropic complex refractive index of graphene oxide thin films.

The polarization response of graphene oxide (GO)-coated planarized optical waveguides is used to determine the complex refractive index of GO film. GO films with thicknesses between 0.10 and 0.71 µm were coated on planarized optical waveguides. GO-coated waveguides exhibit large polarization dependent losses-and the polarization response depends strongly on the GO coating thickness. The response was used, together with finite element analysis, to determine the complex refractive index of the GO film. The complex refractive indices of GO films for both TE- and TM-polarized light at a wavelength of 1550 nm were found to be 1.71+0.09i and 1.58+0.05i, respectively. The uncertainties of nGO and kGO for TE-polarized light are ±0.02 and ±0.03, respectively, whereas the uncertainties of nGO and kGO for TM-polarized light are ±0.05 and ±0.02, respectively.

Fabrication of a carbon nanotube/tungsten disulfide visible spectrum photodetector.

Two-dimensional-material-based photodetectors are gaining prominence in optoelectronic applications, but there are certain factors to consider with bulk material usage. The demand for a highly responsive and highly efficient device with an inexpensive fabrication method is always of paramount importance. Carbon nanotubes (CNT) are well known, owing to their upheld vigorous structural and optoelectronic characteristics, but to fabricate them at a large scale involves multifarious processes. A visible range photodetector device structure developed using a simple and inexpensive drop-casting technique is reported here. The optoelectronic characteristics of the device are studied with IV measurements under the light and dark conditions by incorporating a thin CNT layer on top of tungsten-disulfide-based heterojunction photodetector to enhance the overall characteristics such as detectivity, responsivity, photocurrent, rise time, and fall time in the visible range of the light spectrum with a violet light source at 441 nm. In the DC bias voltage range of -20 to 20 V, IV measurements are carried out under dark and illumination conditions with different incident power densities. The threshold voltage is recognized at 2.0 V. Photocurrent is found to be highly dependent on the state of the incident light. For 0.3074mW/cm2 illuminated power, the highest responsivity and detectivity are determined to be 0.57 A/W and 2.89×1011 Jones. These findings encourage an alternative fabrication method at a large scale to grow CNTs for the enhancement of optoelectronic properties of present two-dimensional-material-based optoelectronic and photonics applications.

Laser-heated needle for biopsy tract ablation: In vivo study of rabbit liver biopsy.

PURPOSE: To investigate the efficacy of a newly-developed laser-heated core biopsy needle in the thermal ablation of biopsy tract to reduce hemorrhage after biopsy using in vivo rabbit's liver model. MATERIALS AND METHODS: Five male New Zealand White rabbits weighed between 1.5 and 4.0 kg were anesthetized and their livers were exposed. 18 liver biopsies were performed under control group (without tract ablation, n = 9) and study group (with tract ablation, n = 9) settings. The needle insertion depth (~3 cm) and rate of retraction (~3 mm/s) were fixed in all the experiments. For tract ablation, three different needle temperatures (100, 120 and 150 °C) were compared. The blood loss at each biopsy site was measured by weighing the gauze pads before and after blood absorption. The rabbits were euthanized immediately and the liver specimens were stained with hematoxylin-eosin (H&E) for further histopathological examination (HPE). RESULTS: The average blood loss in the study group was reduced significantly (p < 0.05) compared to the control group. The highest percentage of bleeding reduction was observed at the needle temperature of 150 °C (93.8%), followed by 120 °C (85.8%) and 100 °C (84.2%). The HPE results show that the laser-heated core biopsy needle was able to cause lateral coagulative necrosis up to 14 mm diameter along the ablation tract. CONCLUSION: The laser-heated core biopsy needle reduced hemorrhage up to 93.8% and induced homogenous coagulative necrosis along the ablation tract in the rabbits' livers. This could potentially reduce the risk of tumor seeding in clinical settings.

Cascaded Fabry-Perot interferometer-regenerated fiber Bragg grating structure for temperature-strain measurement under extreme temperature conditions.

We demonstrated an optical fiber sensor based on a cascaded fiber Fabry-Perot interferometer (FPI)-regenerated fiber Bragg grating (RFBG) for simultaneous measurement of temperature and strain under high temperature environments. The FPI is manufactured from a ∼74 µm long hollow core silica tube (HCST) sandwiched between two single mode fibers (SMFs). The RFBG is inscribed in one of the SMF arms which is embedded inside an alundum tube, making it insensitive to the applied strain on the entire fiber sensor, just in case the temperature and strain recovery process are described using the strain-free RFBG instead of a characteristic due-parameter matrix. This feature is intended for thermal compensation for the FPI structure that is sensitive to both temperature and strain. In the characterization tests, the proposed device has exhibited a temperature sensitivity ∼ 18.01 pm/°C in the range of 100 °C - 1000 °C and excellent linear response to strain in the range of 300 °C - 1000 °C. The measured strain sensitivity is as high as ∼ 2.17 pm/µÉ› for a detection range from 0 µÉ› to 450 µÉ› at 800 °C, which is ∼ 1.5 times that of a FPI-RFBG without the alundum tube.

Reduced Graphene Oxide-Silver Nanoparticles for Optical Pulse Generation in Ytterbium- and Erbium-Doped Fiber Lasers.

This work has demonstrated the potential of a reduced graphene oxide silver/polyvinyl alcohol (rGO-Ag/PVA) film as a saturable absorber (SA) in ytterbium and erbium based Q-switched optical fiber lasers. The facile hydrothermal method was used to synthesize the nanocomposite between rGO and Ag nanoparticles. This was followed by a simple solution method to form the rGO-Ag film using PVA as the host polymer. From nonlinear absorption characterization, the rGO-Ag/PVA SA was determined to have a modulation depth of 30%, a nonsaturable loss of 70%, and a saturable intensity of 0.63 kW/cm2. Stable self-starting Q-switched pulses were obtained at the threshold pump power of 72.76 mW and 18.63 mW in the ytterbium-doped (YDFL) and erbium-doped fiber laser (EDFL) cavities respectively. The center operating wavelengths were observed at 1044.4 nm and 1560 nm for the two cavities. The shortest pulse width and maximum repetition rate of the YDFL and EDFL were 1.10 µs and 62.10 kHz and 1.38 µs and 76.63 kHz respectively. This work has demonstrated that the rGO-Ag/PVA film is suitable as an SA for pulse generation in the 1.0 and 1.5 µm regions and would have many potential photonics applications.

56 nm Wide-Band Tunable Q-Switched Erbium Doped Fiber Laser with Tungsten Ditelluride (WTe2) Saturable Absorber.

A wide-band and tunable Q-switched erbium-doped fiber (EDF) laser operating at 1560.5 nm with a tungsten ditelluride (WTe2) saturable absorber (SA) is demonstrated. The semi-metallic nature of WTe2 as well as its small band gap and excellent nonlinear optical properties make it an excellent SA material. The laser cavity uses an 89.5 cm long EDF, pumped by a 980 nm laser diode as the linear gain while the WTe2 based SA generates the pulsed output. The WTe2 based SA has a modulation depth, non-saturable loss and saturation intensity of about 21.4%, 78.6%, and 0.35 kW/cm2 respectively. Stable pulses with a maximum repetition rate of 55.56 kHz, narrowest pulse width of 1.77 µs and highest pulse energy of 18.09 nJ are obtained at the maximum pump power of 244.5 mW. A 56 nm tuning range is obtained in the laser cavity, and the output is observed having a signal to noise ratio (SNR) of 48.5 dB. The demonstrated laser has potential for use in a large number of photonics applications.

Nanosecond pulse laser generation at 1.55 and 2 µm regions by integrating a piece of newly developed chromium-doped fiber-based saturable absorber.

This paper demonstrated the nanosecond pulse laser operation at 1.55 and 2 µm wavelength regions using a newly develop chromium-doped fiber (CrDF) as a saturable absorber (SA) to convert efficiently continuous-wave laser operation to nanosecond pulse laser operation. The laser uses an erbium-doped fiber (EDF) and thulium-doped fiber as the gain medium. A piece of 10 cm long CrDF was integrated into both laser cavities to generate nanosecond pulse laser operation. In 1.55 region generation, an additional single-mode fiber (SMF) 100 m long was added into the EDF laser cavity. Stable pulse generation occurred at a repetition rate of 1 MHz with a pulse width of 432 ns and a signal-to-noise ratio (SNR) of 66 dB. The highest peak power of 24 mW was obtained at 142 mW pump power. In 2 µm region generation, the obtained repetition rate was 10 MHz with a pulse width and SNR of 59 ns and 41 dB, respectively. The highest peak power was only 8.3 mW. By looking into the findings, the newly developed CrDF SA has a potential to be further enhanced toward better generation of ultrashort pulse fiber lasers.

1.3 µm fiber grating in a thin-core fiber for LP01-LP11 mode converters and sensing ability.

We demonstrate an all-fiber structure that can realize LP01-LP11 mode conversion and twist measurement. It is a thin-core fiber (TCF) grating at a wavelength of 1310 nm cascaded to a short segment of a TCF of a different core size. It is found that the different core size of the TCF between the fiber and the grating has an impact on the excitation of a higher-order mode and mode conversion efficiency. The fiber structure exhibits a good linear response to twisting, strain, and temperature. Depending on the associated mode, the mode intensity and the wavelength for exciting the peaks of the grating have different sensitivities to twisting angle, applied strain, and temperature. These properties can be exploited for simultaneous measurement.

Tungsten-disulphide-based heterojunction photodetector.

Two-dimensional (2D) materials have realized significant new applications in photonics, electronics, and optoelectronics. Among these materials is tungsten disulphide (WS2), which is a 2D material that shows excellent optoelectronic properties, tunable/sizable bandgap in the visible range, and good absorption. A polycrystalline WS2 thin film is successfully deposited on a substrate using radio frequency magnetron sputtering at room temperature. The x-ray diffraction pattern reveals two hexagonal structured peaks along the (100) and (110) planes. Energy-dispersive x-ray spectroscopy reveals a non-stoichiometric WS2 film with 1.25 ratio of S/W for a 156.3 nm thick film, while Raman shifts are observed at the E2g1 and A1g phonon modes located at 350.70 cm-1 and 415.60 cm-1, respectively. A sandwiched heterojunction photodetector device is successfully fabricated and illuminated within the violet range at 441 nm and 10 V of bias voltage. The maximum photocurrent values are calculated as 0.95 µA, while the responsivity is observed at 169.3 mA W-1 and detectivity 1.48×108 Jones at illuminated power of 0.6124 µm. These results highlight the adaptability of the present technique for large-scale applications as well as the flexibility to promote development of advanced optoelectronic devices.

Regenerated grating produced in a multimaterial glass-based photosensitive fiber with an ultrahigh thermal regeneration ratio.

This work demonstrates thermal regeneration of gratings inscribed in a new type of multi-material glass-based photosensitive fiber. And isothermal annealing procedure has been carried out on a type-I seed grating (SG) imprinted in erbium-doped zirconia-yttria-alumina-germanium (Er-ZYAG) silica glass-based fiber, which is initiated from room temperature of 25°C up to 900°C. The findings show that the created regenerated grating (RG) has an ultrahigh thermal regeneration ratio with a value of 0.72.

A Recent Progress of Steel Bar Corrosion Diagnostic Techniques in RC Structures.

Corrosion of steel bar is one of key factors undermining reinforced concrete (RC) structures in a harsh environment. This paper attempts to review the non-destructive procedures from the aspect of the corrosion measurement techniques, especially their advantages and limitations. Systematical classification of diagnostic methods is carried out to determine any probable corrosion issues before the structures become severe, and helps choose the suitable method according to different construction features. Furthermore, the three electrochemical factors method is introduced to inspire researchers to combine various techniques to improve corrosion evaluation accuracy. The recommendations for future work are summarized, in conclusion.

Effect of two annealing processes on the thermal regeneration of fiber Bragg gratings in hydrogenated standard optical fibers.

In this work, we demonstrate the thermal regeneration of fiber Bragg gratings written in the hydrogenated standard communication optical fibers by two annealing processes. The first annealing process is done at an intermediate temperature (500°C, 700°C, and 900°C) for a specific period of time before cooling down to room temperature. The second annealing is at 1000°C in which the thermal regeneration is attained. The experimental results show that the regenerated gratings that are preannealed at 700°C have charted a reflectivity larger than 65%. They have higher thermal stability compared to that of the standard annealing process. Meanwhile the difference in temperature sensitivity is very small. The temperature sensitivities of regenerated gratings, which have undergone only two annealing processes, are 16.1 pm/°C and 15.8 pm/°C, respectively.

Temperature-independent hygrometry using micromachined photonic crystal fiber.

An in-fiber Mach-Zehnder interferometer (MZI) is proposed and experimentally demonstrated for relative humidity (RH) and temperature measurements. The MZI is formed by a grapefruit-shaped photonic crystal fiber (G-PCF) cascaded with a short section of multimode fiber that serves as a mode coupler. To enhance sensitivity to humidity, femtosecond laser micromachining was performed to remove a portion of cladding of the G-PCF to expose its core to the ambient medium. The output interference spectrum is fast Fourier transformed to produce a spatial frequency spectrum that describes the intensity composition of the cladding modes in the MZI. In our investigation, it was observed that the interference dip intensity has a sensitivity of -0.077 dB/% RH to the change of RH in the range of 25%-80% RH, whereas the dip wavelength has a temperature sensitivity of ∼3.3 pm/°C in the range of 25°C-70°C. In addition, the dip intensity was insensitive to temperature. These characteristics have provided convenience in eliminating temperature cross talk and achieving accurate humidity measurement.

Mach-Zehnder interferometric magnetic field sensor based on a photonic crystal fiber and magnetic fluid.

A Mach-Zehnder interferometric magnetic field sensor based on a photonic crystal fiber (PCF) and magnetic fluid (MF) was designed and experimentally demonstrated. The sensing probe consists of a single-mode-(SM)-multimode-PCF-SM fiber structure through arc fusion splicing. It was then laser engrave notched with the femtosecond laser so that the PCF cladding was selectively infilled MF. A well-defined interference pattern was obtained on account of the tunable refractive index of the MF infilled PCF cladding. The transmission spectra of the proposed sensor under different magnetic field intensities have been measured and theoretically analyzed. The results show that the sensitivity of the proposed sensor can reach -0.13 dB/mT and 0.07334 nm/mT in the magnetic field intensity from 1 mT to 20 mT and 2 mT to 20 mT, respectively.

Chitosan capped nickel oxide nanoparticles as a saturable absorber in a tunable passively Q-switched erbium doped fiber laser.

Nickel oxide (NiO) nanoparticles successfully prepared from a nickel(ii) chloride hexahydrate precursor are used to form a chitosan capped NiO nanoparticle thin film to serve as a saturable absorber (SA) for the generation of passively Q-switched pulses in an erbium doped fiber laser (EDFL). The NiO/chitosan SA based EDFL is able to generate stable pulsed outputs at a low threshold pump power of 104.90 mW with a central wavelength at 1562 nm. The highest pulse energy obtainable by the system is 15.30 nJ at a repetition rate of 42.66 kHz and a pulse duration of 2.02 µs. The laser has a spectral range of 58 nm from 1522 to 1580 nm, covering the C and L bands and even portions of the S band. This study experimentally demonstrates that the potential of the NiO/chitosan film as an SA material for Q-switching operations, combined with the biocompatibility, non-toxicity and high thermal resistance of Chitosan, holds great prospects for a broad range of applications.