Voltametric Sensor Based on Magnetic Chitosan Acetylindole-Based Nanocomposite for the Determination of Sulfamethazine.

Sulfamethazine (SMZ), a persistent antibiotic, is frequently detected in drinking water and milk. For this reason, our research aimed to develop a novel electrochemical sensor based on a magnetic nanocomposite supported on chitosan modified by 3-acetylindole through the formation of chitosan acetylindole Schiff base (Chs-Aci). The objective was to detect extremely low concentrations of SMZ in milk. The synthesized nanocomposites were characterized by various techniques, including FT-IR, XRD, EDX, SEM, and TEM. To enhance the electrocatalytic efficiency for sensitive SMZ detection in food samples, a magnetic chitosan acetylindole nanocomposite (M-Chs-Aci) was employed as a modifier for a carbon paste electrode (CPE). The electrochemical measurements revealed that the M-Chs-Aci/CPE exhibits good electrocatalytic performance compared to a bare CPE. Moreover, low detection limit, repeatability, and stability were achieved at 0.021 µM, 3.83%, and 94.87%, respectively. Finally, the proposed M-Chs-Aci/CPE proved to be highly effective in detecting SMZ in milk samples. The obtained findings paved the way for the effective usability of M-Chs-Aci/CPE as a sensor for detecting SMZ in real samples, with acceptable recoveries of 95%-98.87%.

Cellulose Sulfate Nanofibers for Enhanced Ammonium Removal.

In this study, a sulfonation approach using chlorosulfonic acid (CSA) to prepare cellulose sulfate nanofibers (CSNFs) from raw jute fibers is demonstrated. Both elemental sulfur content and zeta potential in the CSNFs are found to increase with increasing CSA content used. However, the corresponding crystallinity in the CSNFs decreases with the increasing amount of CSA used due to degradation of cellulose chains under harsh acidic conditions. The ammonium adsorption results from the CSNFs with varying degrees of sulfonation were analyzed using the Langmuir isotherm model, and the analysis showed a very high maximum ammonium adsorption capacity (41.1 mg/g) under neutral pH, comparable to the best value from a synthetic hydrogel in the literature. The high ammonium adsorption capacity of the CSNFs was found to be maintained in a broad acidic range (pH = 2.5 to 6.5).

Unveiling the Impact of Drying Methods on Phytochemical Composition and Antioxidant Activity of Anthemis palestina.

Different drying techniques may alter the chemical composition of plant extracts and consequently affect their bioactivity potential. The current study was designed to reveal the effect of four different drying methods on the phytochemical composition and antioxidant activity of hydrodistilled essential oil (HD-EO) and methanolic (APM) extract obtained from the aerial part of Anthemis palestina from Jordan. Aerial parts of A. palestina in their fresh (FR) form and after drying in shade (ShD), sun (SD), oven at 40 °C (O40D) and 60 °C (O60D), in addition to microwave (MWD), were used to extract their essential oils by hydrodistillation and to prepare the different methanolic extracts (APM). GC/MS analysis of the different HD-EOs revealed qualitative and quantitative differences among the different samples. While FR, O40D, O60D, and MWD EO samples contained mainly sesquiterpene hydrocarbons (35.43%, 29.04%, 53.69%, and 59.38%, respectively), ShD sample was rich in oxygenated monoterpenes (33.57%), and SD-EO contained mainly oxygenated sesquiterpenes (40.36%). Principal component analysis (PCA) and Cluster analysis (CA) grouped the different drying methods based on their impact on the concentration of chemical constituents. SD-EO demonstrated high DPPH and ABTS antioxidant activity (1.31 ± 0.03) × 10-2; (1.66 ± 0.06) × 10-2 µg/mL, respectively). Furthermore, A. paleistina methanolic extracts (APM) obtained after subjecting the plant to different drying methods showed interesting patterns in terms of their TPC, TFC, antioxidant activity, and phytochemical profiling. Of all extracts, SD-APM extract had the highest TPC (105.37 ± 0.19 mg GA/g DE), highest TFC (305.16 ± 3.93 mg Q/g DE) and demonstrated the highest DPPH and ABTS scavenging activities ((4.42 ± 0.02) × 10-2; (3.87 ± 0.02) × 10-2 mg/mL, respectively); all were supported by correlation studies. LC-MS/MS analysis of the different extracts revealed the richness of the SD-APM extract in phenolic acids and flavonoids.

Scrophularia peyronii Post. from Jordan: Chemical Composition of Essential Oil and Phytochemical Profiling of Crude Extracts and Their In Vitro Antioxidant Activity.

The genus Scrophularia is one of the largest genera belonging to the Scrophulariaceae family. Different members of the genus exhibit an interesting, wide spectrum of bioactivities. Accordingly, the current study aimed to investigate, for the first time, the chemical composition of the essential oil of Scrophularia peyronii Post. from Jordan. Additionally, extracts obtained from the aerial parts with solvents of different polarities were assayed for their phytochemical constituents and in vitro antioxidant activities. The major constituents detected in the essential oil, as revealed by GC/MS analysis, contained mainly Z,Z-farnesyl acetone (11.04%), ß-elemene (6.36%), n-octanal (5.98%), and spathulenol (4.58%). Each of the aqueous methanol (Sp-M) and butanol (Sp-B) extracts contained flavonoids, saponins, anthraquinone, and glycosides. Both extracts were evaluated for their total phenolic content (TPC), total flavonoid content (TFC), and their in vitro antioxidant activity, which were assayed using the DPPH radical scavenging activity and ABTS radical scavenging methods. Additionally, the two extracts were then subjected to LC-ESI-MS/MS for the qualitative determination of their secondary metabolite content, especially in flavonoids and phenolic compounds. The results showed that the Sp-B extract of S. peyronii had the highest contents of both phenolic compounds and flavonoids and showed high radical scavenging activity, as determined by the two assay methods, when compared with the Sp-M extract. The LC-ESI-MS/MS analysis resulted in the detection of 21 compounds, including 8 flavonoids, 6 phenolic acids, 6 iridoids, and 2 acids. Although the majority of compounds were detected in both extracts, it was noticed that scropolioside B, 6'-O-cinnamoylharpagide, isoferulic acid, and 6-O-methylcatapol were only detected in the Sp-M fraction.

Synthesis and in Silico Investigation of Organoselenium-Clubbed Schiff Bases as Potential Mpro Inhibitors for the SARS-CoV-2 Replication.

Since the first report of the organoselenium compound, ebselen, as a potent inhibitor of the SARS-CoV-2 Mpro main protease by Z. Jin et al. (Nature, 2020), different OSe analogs have been developed and evaluated for their anti-COVID-19 activities. Herein, organoselenium-clubbed Schiff bases were synthesized in good yields (up to 87%) and characterized using different spectroscopic techniques. Their geometries were studied by DFT using the B3LYP/6-311 (d, p) approach. Ten FDA-approved drugs targeting COVID-19 were used as model pharmacophores to interpret the binding requirements of COVID-19 inhibitors. The antiviral efficiency of the novel organoselenium compounds was assessed by molecular docking against the 6LU7 protein to investigate their possible interactions. Our results showed that the COVID-19 primary protease bound to organoselenium ligands with high binding energy scores ranging from -8.19 to -7.33 Kcal/mol for 4c and 4a to -6.10 to -6.20 Kcal/mol for 6b and 6a. Furthermore, the docking data showed that 4c and 4a are good Mpro inhibitors. Moreover, the drug-likeness studies, including Lipinski's rule and ADMET properties, were also assessed. Interestingly, the organoselenium candidates manifested solid pharmacokinetic qualities in the ADMET studies. Overall, the results demonstrated that the organoselenium-based Schiff bases might serve as possible drugs for the COVID-19 epidemic.

Sodium Alginate-Aldehyde Cellulose Nanocrystal Composite Hydrogel for Doxycycline and Other Tetracycline Removal.

A novel composite hydrogel bead composed of sodium alginate (SA) and aldehyde cellulose nanocrystal (DCNC) was developed for antibiotic remediation through a one-step cross-linking process in a calcium chloride bath. Structural and physical properties of the hydrogel bead, with varying composition ratios, were analyzed using techniques such as BET analysis, SEM imaging, tensile testing, and rheology measurement. The optimal composition ratio was found to be 40% (SA) and 60% (DCNC) by weight. The performance of the SA-DCNC hydrogel bead for antibiotic remediation was evaluated using doxycycline (DOXY) and three other tetracyclines in both single- and multidrug systems, yielding a maximum adsorption capacity of 421.5 mg g-1 at pH 7 and 649.9 mg g-1 at pH 11 for DOXY. The adsorption mechanisms were investigated through adsorption studies focusing on the effects of contact time, pH, concentration, and competitive contaminants, along with X-ray photoelectron spectroscopy analysis of samples. The adsorption of DOXY was confirmed to be the synergetic effects of chemical reaction, electrostatic interaction, hydrogen bonding, and pore diffusion/surface deposition. The SA-DCNC composite hydrogel demonstrated high reusability, with more than 80% of its adsorption efficiency remaining after five cycles of the adsorption-desorption test. The SA-DCNC composite hydrogel bead could be a promising biomaterial for future antibiotic remediation applications in both pilot and industrial scales because of its high adsorption efficiency and ease of recycling.

A Comparative Study of Mechanism and Performance of Anionic and Cationic Dialdehyde Nanocelluloses for Dye Adsorption and Separation.

In this study, anionic dialdehyde cellulose (DAC) and cationic dialdehyde cellulose (c-DAC) nanofibrous adsorbents were prepared via a two-step reaction from bamboo pulp, using sodium periodate and Girard's reagent T as oxidizing and cationizing agents, respectively. The performance of DAC and c-DAC for selective dye adsorption and separation was evaluated by six different organic dyes (with varying charge properties) and certain binary mixtures. Both adsorbents could remove the dyes but with different capability, where DAC exhibited high adsorption efficiency against cationic dyes (e.g., the maximum adsorption capacity for Bismarck brown Y was 552.1 mg/g) and c-DAC exhibited high adsorption efficiency against anionic dyes (e.g., the maximum adsorption capacity for Congo red was 540.3 mg/g). To investigate the adsorption mechanism for these adsorbents, effects of contact time, initial pH value, initial dye concentration, and ionic strength on the adsorption activity against Congo red were investigated. The adsorption equilibrium data of DAC were found to fit best with the Langmuir isotherm model, whereas that of c-DAC were found to fit best with the Freundlich model. Both DAC and c-DAC adsorption kinetic data could be described by the pseudo-second-order kinetic model, and these adsorbents possessed stable adsorption efficiency in the pH range of 4-10. Furthermore, their dye adsorption capabilities were found to increase with increasing ionic strength (salt concentration). The distinctive complementary features of DAC and c-DAC will allow them to remove a wide range of organic dyes from industrial wastewater.

Low Fouling Nanostructured Cellulose Membranes for Ultrafiltration in Wastewater Treatment.

Ultrafiltration (UF) is a common technique used in wastewater treatments. However, the issue of membrane fouling in UF can greatly hinder the effectiveness of the treatments. This study demonstrated a low-fouling composite cellulose membrane system based on microfibrillated cellulose (MFC) and silica nanoparticle additives. The incorporation of 'non-spherical' silica nanoparticles was found to exhibit better structural integration in the membrane (i.e., minimal aggregation of silica nanoparticles in the membrane scaffold) as compared to spherical silica. The resulting composite membranes were tested for UF using local wastewater, where the best-performing membrane exhibited higher permeation flux than commercial polyvinylidene difluoride (PVDF) and polyether sulfone (PES) membranes while maintaining a high separation efficiency (~99.6%) and good flux recovery ratio (>90%). The analysis of the fouling behavior using different models suggested that the processes of cake layer formation and pore-constriction were probably two dominant fouling mechanisms, likely due to the presence of humic substances in wastewater. The demonstrated cellulose composite membrane system showed low-fouling and high restoration capability by a simple hydraulic cleaning method due to the super hydrophilic nature of the cellulose scaffold containing silica nanoparticles.

Synthesis, molecular docking study and anticancer activity of novel 1,3,4-oxadiazole derivatives as potential tubulin inhibitors.

The current study reports on the synthesis and anticancer efficacy of novel oxadiazole derivatives (8a-f) as tubulin polymerization inhibitors. NMR, mass, and elemental studies were used to confirm the newly produced compounds. In contrast to the conventional medicine colchicine, compounds 8e and 8f demonstrated stronger sensitivity and improved IC50 values in the range of 3.19-8.21 µM against breast MCF-7, colorectal HCT116, and liver HepG2 cancer cell lines. The target compounds were tested for enzymatic activity against the tubulin enzyme. Compounds 8e and 8f were shown to have the most effective inhibitory action among the new compounds, with IC50 values of 7.95 and 9.81 nM, respectively. As compared to the reference drug, molecular docking investigations of the developed compounds revealed the crucial hydrogen bonding in addition to the hydrophobic interaction at the binding site, assisting in the prediction of the structural requirements for the found anticancer activity. These findings indicate that the 1,3,4-oxadizole scaffold has the potential for future research into new anticancer medicines.

Fabrication of layered In2S3/WS2 heterostructure for enhanced and efficient photocatalytic CO2 reduction and various paraben degradation in water.

Because of the excessive use of fossil fuels, CO2 emissions into the environment are increasing. An efficient method of converting CO2 to useful carbonaceous products in the presence of light is one way to address the issues associated with energy and environmental remediation. In2S3/WS2 heterostructure has been fabricated using the efficient hydrothermal method. The results of structural, morphological, optical, and photo/electrochemical characterization confirm the formation of a hierarchical, layered heterostructure of type-II. Enhanced photocatalytic activity is observed in InS/WS heterostructure compared to pristine In2S3 and WS2. InS/WS heterostructure exhibit higher photocatalytic activity than pure In2S3 and WS2. For 12 h, photocatalytic CO2 reduction produces 213.4 and 188.6 µmol of CO and CH4, respectively. Furthermore, the photocatalytic ability of the synthesized materials to degrade different parabens (Methyl: MPB, Ethyl: EPB, and Benzyl: BPB) under visible radiation was evaluated. Under optimized conditions, the InS/WS heterostructure degraded 88.6, 90.4, and 95.8% of EPB, BPB, and MPB, respectively, in 90 min. The mechanism of photocatalysis was discussed in detail. MCF-7 cell viability was assessed and found to exhibit low mortality in InS/WS treated MPB aqueous solution. InS/WS heterostructure could improve the fabrication of more sulphide-based layered materials to combat environmental pollution.

Effective Thallium(I) Removal by Nanocellulose Bioadsorbent Prepared by Nitro-Oxidation of Sorghum Stalks.

Thallium(I) (Tl(I)) pollution has become a pressing environmental issue due to its harmful effect on human health and aquatic life. Effective technology to remove Tl(I) ions from drinking water can offer immediate societal benefits especially in the developing countries. In this study, a bio-adsorbent system based on nitro-oxidized nanocellulose (NOCNF) extracted from sorghum stalks was shown to be a highly effective Tl(I) removal medium. The nitro-oxidation process (NOP) is an energy-efficient, zero-waste approach that can extract nanocellulose from any lignocellulosic feedstock, where the effluent can be neutralized directly into a fertilizer without the need for post-treatment. The demonstrated NOCNF adsorbent exhibited high Tl(I) removal efficiency (>90% at concentration < 500 ppm) and high maximum removal capacity (Qm = 1898 mg/g using the Langmuir model). The Tl(I) adsorption mechanism by NOCNF was investigated by thorough characterization of NOCNF-Tl floc samples using spectroscopic (FTIR), diffraction (WAXD), microscopic (SEM, TEM, and AFM) and zeta-potential techniques. The results indicate that adsorption occurs mainly due to electrostatic attraction between cationic Tl(I) ions and anionic carboxylate groups on NOCNF, where the adsorbed Tl(I) sites become nuclei for the growth of thallium oxide nanocrystals at high Tl(I) concentrations. The mineralization process enhances the Tl(I) removal efficiency, and the mechanism is consistent with the isotherm data analysis using the Freundlich model.

Design, synthesis, molecular docking and pharmacological evaluation of novel triazine-based triazole derivatives as potential anticonvulsant agents.

Triazine-linked triazole compounds (4a-j) were designed, synthesized, and then examined for their anticonvulsant abilities. Compounds 4e, 4f, 4g, 4i, and 4j displayed significant anticonvulsant activity in both maximum electroshock seizure (MES) and pentylenetetrazole (PTZ) induced seizure during the preliminary screening. The phase II anticonvulsant activity statistics revealed that compounds 4e, 4f, 4g, 4i, and 4j demonstrated excellent activity as compared to the conventional drugs methaqualone and valproate, supporting the potential of these triazine-linked triazole analogues as novel anticonvulsant agents. To take use of the findings, computational parameters including docking analysis and drug-likeness prediction were carried out. Molecular modelling studies supported the essential pharmacophoric information that the structure activity relationship offered. The triazine-linked triazole analogues that were investigated might be viewed as helpful models for future research and derivatization.

A Novel Electrochemical Sensor for Detection of Nicotine in Tobacco Products Based on Graphene Oxide Nanosheets Conjugated with (1,2-Naphthoquinone-4-Sulphonic Acid) Modified Glassy Carbon Electrode.

A simple electrochemical sensor for nicotine (NIC) detection was performed. The sensor based on a glassy carbon electrode (GCE) was modified by (1,2-naphthoquinone-4-sulphonic acid)(Nq) decorated by graphene oxide (GO) nanocomposite. The synthesized (GO) nanosheets were characterized using X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), FT-IR, and UV-Visible Spectroscopy. The insertion of Nq with GO nanosheets on the surface of GCE displayed high electrocatalytic activity towards NIC compared to the bare GCE. NIC determination was performed under the optimum conditions using 0.10 M of Na2SO4 as a supporting electrolyte with pH 8.0 at a scan rate of 100 mV/s using both cyclic voltammetry (CV) and differential pulse voltammetry (DPV). This electrochemical sensor showed an excellent result for NIC detection. The oxidation peak current increased linearly with a 6.5-245 µM of NIC with R2 = 0.9999. The limit of detection was 12.7 nM. The fabricated electrode provided satisfactory stability, reproducibility, and selectivity for NIC oxidation. The reliable GO/Nq/GCE sensor was successfully applied for detecting NIC in the tobacco product and a urine sample.

DFT, ADMET and Molecular Docking Investigations for the Antimicrobial Activity of 6,6'-Diamino-1,1',3,3'-tetramethyl-5,5'-(4-chlorobenzylidene)bis[pyrimidine-2,4(1H,3H)-dione].

Heterocyclic compounds, including pyrimidine derivatives, exhibit a broad variety of biological and pharmacological activities. In this paper, a previously synthesized novel pyrimidine molecule is proposed, and its pharmaceutical properties are investigated. Computational techniques such as the density functional theory, ADMET evaluation, and molecular docking were applied to elucidate the chemical nature, drug likeness and antibacterial function of molecule. The viewpoint of quantum chemical computations revealed that the molecule was relatively stable and has a high electrophilic nature. The contour maps of HOMO-LUMO and molecular electrostatic potential were analyzed to illustrate the charge density distributions that could be associated with the biological activity. Natural bond orbital (NBO) analysis revealed details about the interaction between donor and acceptor within the bond. Drug likeness and ADMET analysis showed that the molecule possesses the agents of safety and the effective combination therapy as pharmaceutical drug. The antimicrobial activity was investigated using molecular docking. The investigated molecule demonstrated a high affinity for binding within the active sites of antibacterial and antimalarial proteins. The high affinity of the antibacterial protein was proved by its low binding energy (-7.97 kcal/mol) and a low inhibition constant value (1.43 µM). The formation of four conventional hydrogen bonds in ligand-protein interactions confirmed the high stability of the resulting complexes. When compared to known standard drugs, the studied molecule displayed a remarkable antimalarial activity, as indicated by higher binding affinity (B.E. -5.86 kcal/mol & Ki = 50.23 M). The pre-selected molecule could be presented as a promising drug candidate for the development of novel antimicrobial agents.

A Novel Alternative Methods for Decalcification of Water Resources Using Green Agro-Ashes.

The strategic idea in this work was to increase pH values by employing natural alkali sources (i.e., HCO3- and CO32-) from four tested agro-ashes as an alternative to chemicals (i.e., lime or soda ash). The considerable proportion of carbonates and bicarbonates in the investigated ash products had remarkable features, making them viable resources. All ash materials showed a significant ability for Ca ion elimination at high initial Ca ion concentrations. A slight quantity of ash (10 g/L) was sufficient for usage on very hard water contents up to 3000 ppm. Finally, the tested agro-ash was free of cost. Furthermore, unlike other conventional precipitants, such as NaOH, Ca(OH)2, NaHCO3, Na2CO3, and CaO, they are cost effective and ecologically sustainable. There is no need to employ any additional chemicals or modify the agro-ash materials throughout the treatment process. The benefits of the manufactured ash were assessed using a SWOT analysis.

Density Functional Theory and Molecular Docking Investigations of the Chemical and Antibacterial Activities for 1-(4-Hydroxyphenyl)-3-phenylprop-2-en-1-one.

The present investigation informs a descriptive study of 1-(4-Hydroxyphenyl) -3-phenylprop-2-en-1-one compound, by using density functional theory at B3LYP method with 6-311G** basis set. The oxygen atoms and π-system revealed a high chemical reactivity for the title compound as electron donor spots and active sites for an electrophilic attack. Quantum chemical parameters such as hardness (η), softness (S), electronegativity (χ), and electrophilicity (ω) were yielded as descriptors for the molecule's chemical behavior. The optimized molecular structure was obtained, and the experimental data were matched with geometrical analysis values describing the molecule's stable structure. The computed FT-IR and Raman vibrational frequencies were in good agreement with those observed experimentally. In a molecular docking study, the inhibitory potential of the studied molecule was evaluated against the penicillin-binding proteins of Staphylococcus aureus bacteria. The carbonyl group in the molecule was shown to play a significant role in antibacterial activity, four bonds were formed by the carbonyl group with the key protein of the bacteria (three favorable hydrogen bonds plus one van der Waals bond) out of six interactions. The strong antibacterial activity was also indicated by the calculated high binding energy (-7.40 kcal/mol).