Comparison of Infrared Thermography and Other Traditional Techniques to Assess Moisture Content of Wall Specimens.

High moisture content is a recurrent problem in masonry and can jeopardize durability. Therefore, precise and easy-to-use techniques are welcome both to evaluate the state of conservation and to help in the diagnosis of moisture-related problems. In this research, the humidification and drying process of two wall specimens were assessed by infrared thermography and the results were compared with two traditional techniques: surface moisture meter and the gravimetric method. Two climatic chambers were used to impose different ambience conditions to each specimen, to evaluate the impact of air temperature and relative humidity in the results. The qualitative analysis of the thermal images allowed the identification of the phenomena. The quantitative analysis showed that the order of magnitude of the temperature gradient that translates high humidity levels is substantially different in the two chambers, pointing to the influence of the surrounding environment. The presented analysis contributes to identifying the criteria indicative of moisture-related problems in two different scenarios and discusses the correlation between the non-destructive techniques and the moisture content in the masonry walls. The limitations and future research gaps regarding the use of IRT to assess moisture are also highlighted.

Experimental and Numerical Simulation of a Radiant Floor System: The Impact of Different Screed Mortars and Floor Finishings.

The radiant floor system market is growing rapidly because Europe is moving toward a low-carbon economy and increased awareness about environmental sustainability and energy efficiency, stimulated by the ambitious EU Energy Efficient Directive and nZEB challenge. The high growth rate of the market share is due to the involvement of homeowners in the specifications of their living commodities, so they are thus willing to invest more at the initial stage to obtain long-term benefits and lower energy exploration costs. We performed an experimental campaign over three slabs with a hydronic radiant floor system of equal dimensions, shape, and pipe pitch with different screed mortar formulations to assess their performance throughout a heating/cooling cycle. The temperature at different heights within the interior of the screed mortars and at the surface were monitored. The results revealed that an improved screed mortar has a relevant impact on the efficiency of the system. Moreover, a three-dimensional transient heat transfer model was validated using the experimental data. The model was used to evaluate the impact of different finishing materials, namely wood, cork, ceramic, and linoleum, on the floor surface temperatures. The results showed differences of 15% in the surface temperature when using different floor finishing solutions.

Emissivity of Building Materials for Infrared Measurements.

Infrared thermography (IRT) is a technique increasingly used in building inspection. If in many applications it is sufficient to analyze the thermal patterns, others exist in which the exact determination of the surface temperature is a fundamental aspect. In these circumstances, the emissivity of the surfaces assumes special relevance, being probably the most important property in the definition of the boundary conditions. However, information on the uncertainty involved in its measurement, as well as the conditions that influence it, is scarce. This article presents an innovative contribution both to the characterization of the emissivity of various construction materials, and to the discussion of emissivity measurement procedures and the attendant uncertainty. In this sense, three experimental campaigns were carried out: T.I, preliminary tests to assess the initial conditions required for an accurate IRT measurement of the emissivity (reference tape and position of the camera); T.II, assessment of the emissivity of nine different building materials, in dry conditions, using the emissometer and the IRT and black tape methods; and T.III, assessment of the emissivity of three materials during the drying process. The results confirmed that emissivity is a crucial parameter for the accurate measurement of surface temperature. Emissivity measurements carried out with IRT (black tape method) and with the emissometer returned meaningful differences when compared with the values available in the literature. This disagreement led to surface temperature differences of up to 7 °C (emissometer versus reference values). This research also highlighted that the moisture content of the materials influences the emissivity values, with fluctuations that can be greater than 10%, and that the effect of moisture is visible even for low values of moisture content.

Biochemical and hematologic changes in whole blood from Brazilian horses stored in citrate-phosphate-dextrose-adenine pouches for up to 28 days.

BACKGROUND: Anaerobic cellular metabolism causes a series of structural and physiologic changes during storage that could compromise post-transfusion viability, reducing the safety of using blood stored for an extended period. OBJECTIVE: We aimed to follow the biochemical and hematologic alterations of equine blood stored in plastic bags containing citrate-phosphate-dextrose-adenine (CPDA-1) for up to 28 days. METHODS: Whole blood samples (450 mL) were collected from 20 Brazilian Saddle horses into CPDA-1 pouches and stored between 2°C and 6°C in a blood bank. On days 0, 7, 14, 21, and 28 of storage, blood samples were taken and submitted for biochemical (sodium [Na+ ], potassium [K+ ], glucose, and lactate) and hematologic (hemoglobin [Hb], hematocrit [HCT], mean corpuscular volume [MCV], percent hemolysis [% hemolysis]) analyses. RESULTS: The only time the blood pH levels dipped below 7 was after D21 of storage, and the levels were significantly lower than those on the first storage day (D0). Potassium concentrations showed significant increases from D7 and then remained increased throughout the experimental period. Chloride and lactate concentrations revealed a significantly increased trend from D7 that was maintained over time. Mean corpuscular volumes increased significantly on D7 and D14 and, thereafter, remained stable. The mean % hemolysis increased on D28, which was significantly higher than D0. No bacterial growth was found in any pouch after 28 days of storage. CONCLUSIONS: Significant and gradual biochemical changes were observed in equine whole blood during prolonged storage. These changes could compromise the clinical conditions of patients requiring transfusion. In vivo studies are needed to evaluate the effects as well as survival rates and efficacy of transfused red blood cells in recipients.

Quantitative Infrared Thermography to Evaluate the Humidification of Lightweight Concrete.

Moisture is one of the major causes of problems in buildings, and it can compromise their performance. Infrared thermography (IRT) is a non-destructive testing technology that can be used to assess the humidification phenomenon and, thus, prevent some of the problems caused by moisture. The images obtained by IRT reflect the thermal patterns of the surface under study and can be evaluated using a quantitative approach, which allows not only the traditional visualization of the thermal patterns but also quantification of surface temperatures and/or their differences. The relevance of this work is related to the discussion of the strengths and weaknesses of several methods to quantitatively assess the humidification phenomenon using IRT. For that purpose, the partial humidification by the bottom surface of a lightweight concrete specimen was considered as a case study. To evaluate the thermal gradients, the evolution of the thermal imaging throughout the measurement period and the definition of the areas particularly affected by moisture, a methodology that included a pre-processing phase for data reduction, followed by a data processing phase, were implemented. In the data processing, different statistical and numerical methods were tested. The results of the statistical descriptive analysis highlighted the time variation of the surface temperature, both when considering the entire specimen and when considering only specific areas. The variability of the temperatures at certain moments of the experiment could be observed in the box-plot representation. The image subtraction proved to be an interesting technique to quantify the temperature differences if the first image was used as reference. A thermal index, TI, was proposed to assess the cooling rate. The index highlighted the initial instant when the effect of moisture on the surface temperature was detectable.

Assessment of Distal Motor Latency of the Femoral Nerve in Clinically Healthy Adult Dogs.

This study aimed to evaluate femoral nerve latency time recorded from both vastus lateralis and vastus medialis muscles, in clinically healthy dogs. Eighteen adult dogs were distributed into 2 distinct body mass ranges (Group 1: 1-4.1 kg, n= 9; Group 2: 4.2-13 kg, n= 8), according to the median body mass (4.1 kg). Distal motor latencies for the femoral nerve were obtained in right- and left hind limbs. Platinum surface electrodes were used to record the latency of femoral nerve from the vastus lateralis muscle, whereas coaxial needle electrodes were used to record the latency from the vastus medialis muscle. The distal motor nerve latencies were 1.52 ± .23 milliseconds and 1.69 ± .42 milliseconds, respectively, for vastus lateralis and vastus medialis muscles. There were no significant differences of distal motor nerve latencies between vastus lateralis and vastus medialis muscles. Hind limb length of Group 1 was significant shorter than Group 2. There were no significant differences of latencies between Groups 1 and 2. No significant correlations were observed between latency and body mass, and between latency and hind limb length for dogs of both groups. In conclusion, the femoral motor latency measurement was easy to obtain and may supply additional data in the examination of diseases that affect the hind limbs. Latency values of vastus lateralis longer than 1.52 ± .23 milliseconds in small/medium-sized breeds may be considered as suggestive of a femoral neuropathy.

Comparison of analgesia provided by lidocaine, lidocaine-morphine or lidocaine-tramadol delivered epidurally in dogs following orchiectomy.

OBJECTIVE: To evaluate and compare the postoperative analgesia provided by epidural lidocaine, lidocaine/morphine or lidocaine/tramadol in dogs following elective orchiectomy. STUDY DESIGN: Prospective experimental trial. ANIMALS: Thirty-six mongrel dogs aged 2-8 years old, weighing 6.6-22 kg. METHODS: The dogs received 6.0 mg kg(-1) of lidocaine combined with 1.0 mg kg(-1) of tramadol, 0.1 mg kg(-1) of morphine or 0.01 mL kg(-1) of 0.9% NaCl epidurally. Analgesia was assessed at 4, 8, 12, 18 and 24 hours (T4, T8, T12 and T24) after the offset of lidocaine using a scale composed of physiologic and behavioral parameters. Rescue analgesia with morphine (0.2 mg kg(-1) , IM) was performed if the evaluation score exceeded 10 during the postoperative period. The scores over time were analyzed using the Friedman's two-way analysis of variance and the comparison between groups was made by the Kruskal-Wallis test with statistical significances accepted if p ≤ 0.05. RESULTS: There were no differences in the pain scores between the morphine and tramadol groups over time and no rescue analgesia was administered. In the NaCl group, rescue analgesia was needed at T4, T8 and T12. Within this group, the final evaluation times (T18 and T24) had lower pain scores than at T4, T8 and T12. CONCLUSIONS AND CLINICAL RELEVANCE: Epidural lidocaine/tramadol provided an analgesic effect comparable to that of epidural lidocaine/morphine during the first 12 hours after surgical castration without substantial side effects, suggesting that tramadol may be an effective postoperative analgesic in dogs submitted to this surgical procedure.

Treatment of a periarticular tibial fracture in a foal with a hybrid external fixator.

OBJECTIVE: To report repair of a right proximal tibial Salter-Harris type II fracture in a foal with a hybrid external fixator (HEF). STUDY DESIGN: Case report. ANIMALS: A 5-month-old male foal. METHODS: After open surgical reduction, an HEF built with wires, 2 half-rings, 3 half-threaded connecting rods, and Schanz pins was used to stabilize the fracture. RESULTS: Immediately after surgery, the foal had relatively good weight bearing. The HEF was removed at 60 days after radiographic confirmation of healing. CONCLUSIONS: HEF can be used to stabilize a proximal tibial Salter-Harris type II fracture in a 5-month-old foal. CLINICAL RELEVANCE: HEF should be considered as another option for repair of proximal tibial Salter-Harris type II fractures in foals.

Brachial plexus blockade in chickens with 0.75% ropivacaine.

OBJECTIVE: To evaluate the quality of brachial plexus blockade with 0.75% ropivacaine in domestic chickens. STUDY DESIGN: Prospective experimental trial. ANIMALS: Six 30-week-old female chickens, weighing 4.5 +/- 0.4 kg. METHODS: Six brachial plexus injections were performed after anesthetic induction with isoflurane. After achieving adequate muscle relaxation, the animals were positioned in dorsal recumbency and injected with ropivacaine (1 mL kg(-1)). The birds recovered and assessments of motor function and response to pinch were scored every 5 minutes for 180 minutes. The scores were from zero (no response) to three (greatest response). The scores over time were analyzed using a Wilcoxon nonparametric test with statistical significance accepted if p 0.05). CONCLUSIONS AND CLINICAL RELEVANCE: No complications were observed after the technique. Brachial plexus blockade with 0.75% ropivacaine is a simple and effective technique for procedures on the thoracic limb of domestic chickens.

Comparative study of epidural xylazine or clonidine in horses.

OBJECTIVE: To evaluate the cardiorespiratory and behavioural effects of epidural xylazine (XYL) or clonidine (CLO) in horses. STUDY DESIGN: Blinded, randomized experimental study. ANIMALS: Twelve healthy Arabian yearling horses weighing 117-204 kg were randomly allocated into two groups: XYL (n = 6) and CLO (n = 6). METHODS: An epidural catheter was inserted and a facial arterial catheter was placed and the next day the horses were restrained in stocks. Baseline values for heart (HR) and respiratory (RR) rates, arterial pressure and behavioural responses were evaluated before (T0) and 10, 20, 30, 45, 60, 90 and 120 minutes after epidural injection (T10-T120). The horses received 0.2 mg kg(-1) of XYL or 5 microg kg(-1) CLO; adjusted to (3.4 + (body weight in kg x 0.013) mL with saline. Data were analysed by the Kolmogorov-Smirnov test, one-way anova with repeated measures, and one-way anova followed by a Student-Newman-Keuls test or Fisher's exact test, as necessary. Significance was set at p < or = 0.05. RESULTS: Sedation and ataxia were seen at T10, persisting until T120 in four and three horses, respectively, in XYL and all horses in CLO respectively. Two XYL and one CLO horses became recumbent at T45 and T25 respectively. Penile prolapse occurred in four of five males at T30 and T45, in the XYL and CLO groups, respectively, resolving by T120. Tail relaxation was present from T10 to T120 in all horses in XYL and in four horses in CLO. Head drop was observed from T20 to T60 and from T10 to T120 in XYL and CLO respectively. Respiratory rate decreased significantly only at T45 in the CLO group. Heart rate and arterial blood pressure remained stable. CONCLUSIONS AND CLINICAL RELEVANCE: Epidural CLO and XYL produce similar cardiorespiratory and behavioural changes but neither would be safe to use clinically at the doses used in this study.

Pre-emptive epidural ketamine or S(+)-ketamine in post-incisional pain in dogs: a comparative study.

OBJECTIVE: To compare the pre-emptive analgesic effects of epidural ketamine or S(+)-ketamine on post-incisional hyperalgesia. STUDY DESIGN: Prospective randomized study. ANIMALS: Twenty-four mongrel dogs (1-5 years, weighing 11.9+/-1.8 kg). METHODS: Dogs were anesthetized with propofol (5 mg/kg intravenously) and a lumbosacral epidural catheter was placed. Dogs were randomly allocated to 3 groups, each with 8 dogs. The control group (CG) was administered saline solution (0.3 mL/kg); the ketamine group (KG) ketamine (0.6 mg/kg); and the S(+)-ketamine group (SG) S(+)-ketamine (0.6 mg/kg). The final volume was adjusted to 0.3 mL/kg in all groups. Five minutes after the epidural injection a surgical incision was made in the common pad of the right hind limb and was immediately closed with simple interrupted nylon suture. Respiratory (RR) and heart (HR) rates, rectal temperature (T), sedation (S), lameness score, and mechanical nociceptive threshold by von Frey filaments were evaluated before the propofol anesthesia and at 15, 30, 45, 60, 75, and 90 minutes and then at 2, 4, 6, 8, 12, and 24 hours after epidural injection. RESULTS: There were no differences in RR, HR, T, or S between groups. Motor blockade of the hind limbs was observed during 20+/-3.6 minutes in KG and during 30.6+/-7.5 minutes in SG (mean+/-SD). Mechanical force applied to obtain an aversive response was higher from 45 minutes to 12 hours in KG and from 60 to 90 minutes in SG, when compared with CG. CONCLUSIONS: Pre-emptive epidural ketamine induced no alterations in RR and HR, and reduced post-incisional hyperalgesia for a longer time than did S(+) ketamine. CLINICAL RELEVANCE: Although anesthetic and analgesic potency of S(+) ketamine is twice that of ketamine, the racemic form is seemingly better for post-incisional hyperalgesia.