Chemoselective formation of cyclo-aliphatic and cyclo-olefinic 1,3-diols via pressure hydrogenation of potentially biobased platform molecules using Knölker-type catalysts.

The hydrogenative conversions of the biobased platform molecules 4-hydroxycyclopent-2-enone and cyclopentane-1,3-dione to their corresponding 1,3-diols are established using a pre-activated Knölker-type iron catalyst. The catalyst exhibits a high selectivity for ketone reduction, and does not induce dehydration. Moreover, by using different substituents of the ligand, the cis-trans ratio of the products can be affected substantially. A decent compatibility of this catalytic system with various structurally related substrates is demonstrated.

Hydrogenation of Cyclic 1,3-Diones to Their 1,3-Diols Using Heterogeneous Catalysts: Toward a Facile, Robust, Scalable, and Potentially Bio-Based Route.

Cyclopentane-1,3-diol (4b) has gained renewed attention as a potential building block for polymers and fuels because its synthesis from hemicellulose-derived 4-hydroxycyclopent-2-enone (3) was recently disclosed. However, cyclopentane-1,3-dione (4), which is a constitutional isomer of 3, possesses a higher chemical stability and can therefore afford higher carbon mass balances and higher yields of 4b in the hydrogenation reaction under more concentrated conditions. In this work, the hydrogenation of 4 into 4b over a commercial Ru/C catalyst was systematically investigated on a bench scale through kinetic studies and variation of reaction conditions. Herein, the temperature, H2-pressure, and the solvent choice were found to have significant effects on the reaction rate and suppression of undesired dehydration of 4. The cis-trans ratio of 4b is naturally generated as 7:3 in these reactions. However, at elevated reaction temperatures, 4b epimerizes, yielding more trans products. This effect was also studied and rationalized from a thermodynamic perspective using DFT. The combined optimized reaction conditions provided 78% yield for 4b, and successful applications to 8-fold scaled up reactions (40 g) and a substrate scope of several 1,3-diones demonstrate the general applicability of this catalytic approach.

Manganese-catalyzed selective oxidation of aliphatic C-H groups and secondary alcohols to ketones with hydrogen peroxide.

An efficient and simple method for selective oxidation of secondary alcohols and oxidation of alkanes to ketones is reported. An in situ prepared catalyst is employed based on manganese(II) salts, pyridine-2-carboxylic acid, and butanedione, which provides good-to-excellent conversions and yields with high turnover numbers (up to 10 000) with H2 O2 as oxidant at ambient temperatures. In substrates bearing multiple alcohol groups, secondary alcohols are converted to ketones selectively and, in general, benzyl C-H oxidation proceeds in preference to aliphatic C-H oxidation.

The unexpected role of pyridine-2-carboxylic acid in manganese based oxidation catalysis with pyridin-2-yl based ligands.

A number of manganese-based catalysts employing ligands whose structures incorporate pyridyl groups have been reported previously to achieve both high turnover numbers and selectivity in the oxidation of alkenes and alcohols, using H(2)O(2) as terminal oxidant. Here we report our recent finding that these ligands decompose in situ to pyridine-2-carboxylic acid and its derivatives, in the presence of a manganese source, H(2)O(2) and a base. Importantly, the decomposition occurs prior to the onset of catalysed oxidation of organic substrates. It is found that the pyridine-2-carboxylic acid formed, together with a manganese source, provides for the observed catalytic activity. The degradation of this series of pyridyl ligands to pyridine-2-carboxylic acid under reaction conditions is demonstrated by (1)H NMR spectroscopy. In all cases the activity and selectivity of the manganese/pyridyl containing ligand systems are identical to that observed with the corresponding number of equivalents of pyridine-2-carboxylic acid; except that, when pyridine-2-carboxylic acid is used directly, a lag phase is not observed and the efficiency in terms of the number of equivalents of H(2)O(2) required decreases from 6-8 equiv. with the pyridin-2-yl based ligands to 1-1.5 equiv. with pyridine-2-carboxylic acid.

Manganese catalyzed cis-dihydroxylation of electron deficient alkenes with H(2)O(2).

A practical method for the multigram scale selective cis-dihydroxylation of electron deficient alkenes such as diethyl fumarate and N-alkyl and N-aryl-maleimides using H(2)O(2) is described. High turnovers (>1000) can be achieved with this efficient manganese based catalyst system, prepared in situ from a manganese salt, pyridine-2-carboxylic acid, a ketone and a base, under ambient conditions. Under optimized conditions, for diethyl fumarate at least 1000 turnovers could be achieved with only 1.5 equiv. of H(2)O(2) with d/l-diethyl tartrate (cis-diol product) as the sole product. For electron rich alkenes, such as cis-cyclooctene, this catalyst provides for efficient epoxidation.

Effect of additives on chemoselectivity and diastereoselectivity in the catalytic epoxidation of chiral allylic alcohols with hydrogen peroxide and binuclear manganese complexes.

The catalytic oxidations of chiral allylic alcohols 2 by manganese complexes of the cyclic triamine 1,4,7-trimethyl-1,4,7-triazacyclononane (tmtacn) 1 and hydrogen peroxide as oxygen donor in the presence of co-catalyst are investigated to understand the factors that affect the catalyst selectivity. Chemoselectivity and diastereoselectivity of catalyst 1 are significantly affected by the structure of the allylic alcohol and the nature and amount of co-catalyst. More pronounced is the influence of the amount of added molar equivalents of H(2)O(2) (20-110 mol % with respect to the substrate). Our present results reflect the complex redox chemistry of the Mn catalyst 1/H(2)O(2)/co-catalyst system in the early phase of the alkene oxidation.

The role of salicylic acid, L-ascorbic acid and oxalic acid in promoting the oxidation of alkenes with H2O2 catalysed by [MnIV2(O)3(tmtacn)2]2+.

The role played by the additives salicylic acid, L-ascorbic acid and oxalic acid in promoting the catalytic activity of [MnIV2(O)3(tmtacn)2](PF6)2 (1(PF6)2, where tmtacn = N,N',N''-trimethyl-1,4,7-triazacyclononane) in the epoxidation and cis-dihydroxylation of alkenes with H2O2 and in suppressing the catalysed decomposition of H2O2 is examined. Whereas aliphatic and aromatic carboxylic acids effect enhancement of the catalytic activity of 1 through the in situ formation dinuclear carboxylato bridged complexes of the type [MnIII2(mu-O)(mu-RCO2)2(tmtacn)2]2+, for L-ascorbic acid and oxalic acid notable differences in reactivity are observed. Although for L-ascorbic acid key differences in the spectroscopic properties of the reaction mixtures are observed compared with carboxylic acids, the involvement of carboxylic acids formed in situ is apparent. For oxalic acid the situation is more complex with two distinct catalyst systems in operation; the first, which engages in epoxidation only, is dominant until the oxalic acid additive is consumed completely at which point carboxylic acids formed in situ take on the role of additives to form a second distinct catalyst system, i.e. that which was observed for alkyl and aromatic carboxylic acids, which yield both cis-diol and epoxide products.

Manganese catalysed asymmetric cis-dihydroxylation with H2O2.

High turnover enantioselective alkene cis-dihydroxylation is achieved with H(2)O(2) catalysed by manganese based complexes containing chiral carboxylato ligands.

Glycol-modified molybdate catalysts for efficient singlet oxygen generation from hydrogen peroxide.

Pretreatment of molybdate-exchanged layered double hydroxides in polyalcohols such as ethylene glycol affords heterogeneous catalysts showing largely improved oxidant efficiency compared to the unmodified materials.

Mechanism of cis-dihydroxylation and epoxidation of alkenes by highly H(2)O(2) efficient dinuclear manganese catalysts.

In the presence of carboxylic acids the complex [Mn(IV)2(micro-O)3(tmtacn)2]2+ (1, where tmtacn = N,N',N''-trimethyl-1,4,7-triazacyclononane) is shown to be highly efficient in catalyzing the oxidation of alkenes to the corresponding cis-diol and epoxide with H2O2 as terminal oxidant. The selectivity of the catalytic system with respect to (w.r.t.) either cis-dihydroxylation or epoxidation of alkenes is shown to be dependent on the carboxylic acid employed. High turnover numbers (t.o.n. > 2000) can be achieved especially w.r.t. cis-dihydroxylation for which the use of 2,6-dichlorobenzoic acid allows for the highest t.o.n. reported thus far for cis-dihydroxylation of alkenes catalyzed by a first-row transition metal and high efficiency w.r.t. the terminal oxidant (H2O2). The high activity and selectivity is due to the in situ formation of bis(micro-carboxylato)-bridged dinuclear manganese(III) complexes. Tuning of the activity of the catalyst by variation in the carboxylate ligands is dependent on both the electron-withdrawing nature of the ligand and on steric effects. By contrast, the cis-diol/epoxide selectivity is dominated by steric factors. The role of solvent, catalyst oxidation state, H2O, and carboxylic acid concentration and the nature of the carboxylic acid employed on both the activity and the selectivity of the catalysis are explored together with speciation analysis and isotope labeling studies. The results confirm that the complexes of the type [Mn2(micro-O)(micro-R-CO2)2(tmtacn)2]2+, which show remarkable redox and solvent-dependent coordination chemistry, are the resting state of the catalytic system and that they retain a dinuclear structure throughout the catalytic cycle. The mechanistic understanding obtained from these studies holds considerable implications for both homogeneous manganese oxidation catalysis and in understanding related biological systems such as dinuclear catalase and arginase enzymes.

Recovery of homogeneous polyoxometallate catalysts from aqueous and organic media by a mesoporous ceramic membrane without loss of catalytic activity.

The recovery of homogeneous polyoxometallate (POM) oxidation catalysts from aqueous and non-aqueous media by a nanofiltration process using mesoporous gamma-alumina membranes is reported. The recovery of Q(12)[WZn(3)(ZnW(9)O(34))(2)] (Q=[MeN(n-C(8)H(17))(3)](+)) from toluene-based media was quantitative within experimental error, while up to 97 % of Na(12)[WZn(3)(ZnW(9)O(34))(2)] could be recovered from water. The toluene-soluble POM catalyst was used repeatedly in the conversion of cyclooctene to cyclooctene oxide and separated from the product mixture after each reaction. The catalytic activity increased steadily with the number of times that the catalyst had been recycled, which was attributed to partial removal of the excess QCl that is known to have a negative influence on the catalytic activity. Differences in the permeability of the membrane for different liquid media can be attributed to viscosity differences and/or capillary condensation effects. The influence of membrane pore radius on permeability and recovery is discussed.

Synergism between molybdenum and lanthanum in the disproportionation of hydrogen peroxide into singlet oxygen.

The catalytic disproportionation of hydrogen peroxide into singlet molecular oxygen was studied using the combined action of lanthanum(III) and molybdenum(VI). A synergistic effect was observed between both metals, resulting in a strong acceleration of the H2O2 disproportionation. An optimum in the catalytic activity was found at La/Mo and La/NaOH molar ratios of 4/1 and 1/3, respectively.

cis-Dihydroxylation and epoxidation of alkenes by [Mn(2)O(RCO(2))(2)(tmtacn)(2)]: tailoring the selectivity of a highly H(2)O(2)-efficient catalyst.

The carboxylic acid promoted cis-dihydroxylation and epoxidation of alkenes catalyzed by [MnIV2O3(tmtacn)2]2+ 1 employing H2O2 as oxidant is described. The use of carboxylic acids at cocatalytic levels not only is effective in suppressing the inherent catalase activity of 1, but also enables the tuning of the catalyst's selectivity. Spectroscopic studies and X-ray analysis confirm that the control arises from the in situ formation of carboxylate-bridged dinuclear complexes, for example, 2 {[MnIII2O(CCl3CO2)2(tmtacn)2]2+} and 3 {[MnII2(OH)(CCl3CO2)2(tmtacn)2]+}, during catalysis. For the first time, the possibility to tune, through the carboxylate ligands employed, both the selectivity and activity of dinuclear Mn-based catalysts is demonstrated. To our knowledge, the system 1/2,6-dichlorobenzoic acid (up to 2000 turnover numbers for cis-cyclooctanediol) is the most active Os-free cis-dihydroxylation catalyst reported to date.

Lanthanum-exchanged zeolites as active and selective catalysts for the generation of singlet oxygen from hydrogen peroxide.

Lanthanum(III)-exchanged zeolites Beta and USY are active and selective catalysts for the generation of singlet oxygen from H2O2 showing superior activity and oxidant efficiency compared to unsupported La-catalysts, e.g. La(OH)3.

Highly efficient recycling of a "sandwich" type polyoxometalate oxidation catalyst using solvent resistant nanofiltration.

A "sandwich" type polyoxometalate catalyst ([MeN(n-C8H17)3]12[WZn3(ZnW9O34)2]) was very efficiently recycled by nanofiltration with almost quantitative retention, using an alpha-alumina supported mesoporous gamma-alumina membrane.

Continuous process for singlet oxygenation of hydrophobic substrates in microemulsion using a pervaporation membrane.

Chemically generated singlet oxygen (1O2, 1Deltag) is able to oxidize a great deal of hydrophobic substrates from molybdate-catalyzed hydrogen peroxide decomposition, provided a suitable reaction medium such as a microemulsion system is used. However, high substrate concentrations or poorly reactive organics require large amounts of H2O2 that generate high amounts of water and thus destabilize the system. We report results obtained on combining dark singlet oxygenation of hydrophobic substrates in microemulsions with a pervaporation membrane process. To avoid composition alterations after addition of H2O2 during the peroxidation, the reaction mixture circulates through a ceramic membrane module that enables a partial and selective dewatering of the microemulsion. Optimization phase diagrams of sodium molybdate/water/alcohol/anionic surfactant/organic solvent have been elaborated to maximize the catalyst concentration and therefore the reaction rate. The membrane selectivity towards the mixture constituents has been investigated showing that a high retention is observed for the catalyst, for organic solvents and hydrophobic substrates, but not for n-propanol (cosurfactant) and water. The efficiency of such a process is illustrated with the peroxidation of a poorly reactive substrate, viz., beta-pinene.

Mechanistic studies on the Mukaiyama epoxidation.

A detailed mechanistic study on the Mukaiyama epoxidation of limonene with dioxygen as oxidant, bis(acetylacetonato)nickel(II) as catalyst, and an aldehyde as co-reagent is reported. All major products of the reaction have been quantitatively identified, both with isobutyraldehyde and 2-methylundecanal as co-reacting aldehydes. Limonene epoxide is formed in good yield. The main products evolving from the aldehyde are carboxylic acid, CO(2), CO, and lower molecular weight ketone and alcohol (K + A). A mechanism is proposed in which an acylperoxy radical formed by the autoxidation of the aldehyde is the epoxidizing species. The observation of carbon dioxide and (K + A) in a 1:1 molar ratio supports this mechanism. CO(2) and (K + A) are formed in molar amounts of 50-60% with respect to the amount of epoxide produced, indicating that epoxidation takes place not only via acylperoxy radicals but also via a peracid route. Cyclohexene epoxidation was also investigated with a number of different metal complexes as catalysts. Cyclohexene is very sensitive for allylic oxidation, which provides information about the action of the catalyst, e.g., metals that form strongly oxidizing stable high-valence complexes are more likely to induce allylic oxidation. Color changes in the reaction mixture indicate the presence of such high-valence species. In the case of nickel, it was found that low-valence compounds predominate during the reaction, which is in line with the fact that this metal displays the highest selectivity for epoxide. A mechanism that accounts for the observations is presented.

Chiral hydroperoxides as oxygen source in the catalytic stereoselective epoxidation of allylic alcohols by sandwich-type polyoxometalates: control of enantioselectivity through a metal-coordinated template.

The epoxidation of allylic alcohols is shown to be efficiently and selectively catalyzed by the oxidatively resistant sandwich-type polyoxometalates, POMs, namely [WZnM(2)(ZnW(9)O(34))(2)](q)(-) [M = OV(IV), Mn(II), Ru(III), Fe(III), Pd(II), Pt(II), Zn(II); q = 10-12], with organic hydroperoxides as oxygen source. Conspicuous is the fact that the nature of the transition metal M in the central ring of polyoxometalate affects significantly the reactivity, chemoselectivity, regioselectivity, and stereoselectivity of the allylic alcohol epoxidation. For the first time, it is demonstrated that the oxovanadium(IV)-substituted POM, namely [ZnW(VO)(2)(ZnW(9)O(34))(2)](12-), is a highly chemoselective, regioselective, and also stereoselective catalyst for the clean epoxidation of allylic alcohols. A high enantioselectivity (er values up to 95:5) has been achieved with [ZnW(VO)(2)(ZnW(9)O(34))(2)](12)(-) and the sterically demanding TADOOL-derived hydroperoxide TADOOH as regenerative chiral oxygen source. Thus, a POM-catalyzed asymmetric epoxidation of excellent catalytic efficiency (up to 42 000 TON) has been made available for the development of sustainable oxidation processes. The high reactivity and selectivity of this unprecedented oxygen-transfer process are mechanistically rationalized in terms of a peroxy-type vanadium(V) template.

A water-soluble and "self-assembled" polyoxometalate as a recyclable catalyst for oxidation of alcohols in water with hydrogen peroxide.

We have demonstrated that a simply prepared water-soluble polyoxometalate, Na12[WZnZn2(H2O)2(ZnW9O34)2], synthesized from readily available zinc and tungsten salts in the presence of nitric acid, is an effective catalyst for selective alcohol oxidation with hydrogen peroxide in biphasic (water-alcohol) reaction media. Experiments have shown that the "self-assembled" catalyst in its mother liquor was as active as the isolated catalyst. The aqueous catalyst solution is easily separated from the water-insoluble products and can be recycled without loss in activity or selectivity.