Optimizing strength of directly recycled aluminum chip-based parts through a hybrid RSM-GA-ANN approach in sustainable hot forging.

Direct recycling of aluminum waste is crucial in sustainable manufacturing to mitigate environmental impact and conserve resources. This work was carried out to study the application of hot press forging (HPF) in recycling AA6061 aluminum chip waste, aiming to optimize operating factors using Response Surface Methodology (RSM), Artificial Neural Network (ANN) and Genetic algorithm (GA) strategy to maximize the strength of recycled parts. The experimental runs were designed using Full factorial and RSM via Minitab 21 software. RSM-ANN models were employed to examine the effect of factors and their interactions on response and to predict output, while GA-RSM and GA-ANN were used for optimization. The chips of different morphology were cold compressed into billet form and then hot forged. The effect of varying forging temperature (Tp, 450-550°C), holding time (HT, 60-120 minutes), and chip surface area to volume ratio (AS:V, 15.4-52.6 mm2/mm3) on ultimate tensile strength (UTS) was examined. Maximum UTS (237.4 MPa) was achieved at 550°C, 120 minutes and 15.4 mm2/mm3 of chip's AS: V. The Tp had the largest contributing effect ratio on the UTS, followed by HT and AS:V according to ANOVA analysis. The proposed optimization process suggested 550°C, 60 minutes, and 15.4 mm2 as the optimal condition yielding the maximum UTS. The developed models' evaluation results showed that ANN (with MSE = 1.48%) outperformed RSM model. Overall, the study promotes sustainable production by demonstrating the potential of integrating RSM and ML to optimize complex manufacturing processes and improve product quality.

Seasonal screening of pesticide residues in beehive products collected from different districts in Egypt.

Pesticides are of immense importance in agriculture, but they might contaminate bees' products. In this study, samples of honey, pollen, and beeswax were collected, seasonally, from apiaries in Toshka (Aswan), El-Noubariya (El-Beheira), and Ismailia (Ismailia) cities in Egypt. The pesticide residues were analyzed using the GC-MS after being extracted and cleaned using the QuEChERS method. Results showed that samples from El-Noubariya had great content of residues followed by Ismailia, and finally Toshka. Samples collected during fall and winter had the highest pesticide residue contents. Specifically, the phenylconazole fungicide group was repeatedly detected in all the examined samples along with organophosphate insecticides. Beeswax samples had the greatest amounts of pesticide residues followed by pollen and then honey samples. Chlorpyrifos (0.07-39.16 ng/g) and profenofos (1.94-17.00 ng/g) were detected in honey samples and their products. Pyriproxyfen (57.12 ng/g) and chlorpyrifos-methyl (39.16 ng/g) were detected in great amounts in beeswax samples from Ismailia and El-Noubariya, respectively. Yet, according to health hazard and quotient studies, the amounts of pesticides detected in honey do not pose any health threats to humans.

Design, synthesis, pharmacological evaluation, and in silico studies of the activity of novel spiro pyrrolo[3,4-d]pyrimidine derivatives.

In the present study, spiro compounds are shown to have distinctive characteristics because of their interesting conformations and their structural impacts on biological systems. A new family of functionalized spiro pyrrolo[3,4-d]pyrimidines is prepared via the one-pot condensation reaction of amino cyclohexane derivatives with benzaldehyde to prepare fused azaspiroundecanedione and azaspirodecenone/thione derivatives. A series of synthesized spiro compounds were scanned against DPPH and evaluated for their ability to inhibit COX-1 and COX-2. All compounds exhibit significant antiinflammatory activity, and they inhibited both COX-1 and COX-2 enzymes with a selectivity index higher than celecoxib as a reference drug. The most powerful and selective COX-2 inhibitor compounds were 11 and 6, with selectivity indices of 175 and 129.21 in comparison to 31.52 of the standard celecoxib. However, candidate 14 showed a very promising antiinflammatory activity with an IC50 of 6.00, while celecoxib had an IC50 of 14.50. Our findings are promising in the area of medicinal chemistry for further optimization of the newly designed and synthesized compounds regarding the discussed structure-activity relationship study (SAR), in order to obtain a superior antioxidant lead compound in the near future. All chemical structures of the novel synthesized candidates were unequivocally elucidated and confirmed utilizing spectroscopic and elemental investigations.

Alleviation of carbendazim toxicity effect by Moringa oleifera oil and Linum usitatissimum L. oil on testes of male rats: Physiological, histological and in silico study.

Carbendazim (CBZ) is a widely used fungicide that is used to control the unwanted growth of fungi on fruits and vegetables. Sixty male rats were divided into six groups, each having ten. Group one served as control, animals belonging to group two were exposed to CBZ in the measure of 200 mg/kg body weight (BW). In the third and fourth groups, rats were administered 800 mg/kg BW of Moringa oleifera (moringa oil) and Linum usitatissimum L. (flaxseed oil), plus CBZ with the same dose given to group two. Groups five and six were administered with moringa and flaxseed oils respectively for six weeks. A marked decline was seen in oxidative stress markers, reduced glutathione (GSH), superoxide dismutase (SOD), catalase (CAT), and a rise in malondialdehyde (MDA) level in group two with severe histological disruptions. Moringa oil and flaxseed oil were used to alleviate these changes. In addition, a biocomputational molecular docking analysis of three proteins found in male rats was performed. In relation to CBZ (CID:10584007) the screened proteins namely testis-expressed protein (TX101_RAT), EPPI_RAT, and glutathione peroxidase 5 (GPX5_RAT) were docked, and their docking score were obtained (-5.9 kcal/mol), (-5.8 kcal/mol) and (-5.6 kcal/mol) respectively. By examining these interactions in 2D and 3D structures, a detailed understanding of the unique and specific binding affinity, hydrogen bonds, hydrophobic interactions, ionic bonds, and water bonds were obtained. Structure-based virtual screening (SBVS) molecular docking analysis showed that protein interaction with CBZ causes reproductive complications in protein expression and functions by hampering their normal function and blocking active sites.

CuO nanoparticles for green synthesis of significant anti-Helicobacter pylori compounds with in silico studies.

Helicobacter pylori (H. pylori) is a universal health intimidation as mentioned by the World Health Organization. The primary causal agent linked to a number of illnesses, including inflammation and the development of stomach ulcers, is Helicobacter pylori. Since, H. pylori develops antibiotic resistance quickly, current H. pylori treatment approaches are becoming less effective. Our research aims to highlight novel formulation antibiotics using CuO-NPs as catalysts and studied their activity as anti-helicobacter pylori supported by computational studies (POM analysis and molecular docking) software. They were designed for anti-Helicobacter Pylori action. All compounds revealed a bactericidal effect better than the reference McFarland standards.

Implementing circularity measurements in industry 4.0-based manufacturing metrology using MQTT protocol and Open CV: A case study.

In the context of Industry 4.0, manufacturing metrology is crucial for inspecting and measuring machines. The Internet of Things (IoT) technology enables seamless communication between advanced industrial devices through local and cloud computing servers. This study investigates the use of the MQTT protocol to enhance the performance of circularity measurement data transmission between cloud servers and round-hole data sources through Open CV. Accurate inspection of circular characteristics, particularly roundness errors, is vital for lubricant distribution, assemblies, and rotational force innovation. Circularity measurement techniques employ algorithms like the minimal zone circle tolerance algorithm. Vision inspection systems, utilizing image processing techniques, can promptly and accurately detect quality concerns by analyzing the model's surface through circular dimension analysis. This involves sending the model's image to a computer, which employs techniques such as Hough Transform, Edge Detection, and Contour Analysis to identify circular features and extract relevant parameters. This method is utilized in the camera industry and component assembly. To assess the performance, a comparative experiment was conducted between the non-contact-based 3SMVI system and the contact-based CMM system widely used in various industries for roundness evaluation. The CMM technique is known for its high precision but is time-consuming. Experimental results indicated a variation of 5 to 9.6 micrometers between the two methods. It is suggested that using a high-resolution camera and appropriate lighting conditions can further enhance result precision.

Unlocking the potential of microalgae cultivated on wastewater combined with salinity stress to improve biodiesel production.

Microalgae have the potential as a source of biofuels due to their high biomass productivity and ability to grow in a wide range of conditions, including wastewater. This study investigated cultivating two microalgae species, Oocystis pusilla and Chlorococcus infusionum, in wastewater for biodiesel production. Compared to Kühl medium, KC medium resulted in a significant fold increase in cellular dry weight production for both O. pusilla and C. infusionum, with an increase of 1.66 and 1.39, respectively. A concentration of 100% wastewater resulted in the highest growth for O. pusilla, with an increase in biomass and lipid content compared to the KC medium. C. infusionum could not survive in these conditions. For further increase in biomass and lipid yield of O. pusilla, different total dissolved solids (TDS) levels were used. Maximum biomass and lipid productivities were achieved at 3000 ppm TDS, resulting in a 28% increase in biomass (2.50 g/L) and a 158% increase in lipid yield (536.88 mg/g) compared to KC medium. The fatty acid profile of O. pusilla cultivated on aerated wastewater at 3000 ppm TDS showed a high proportion of desirable saturated fatty acids (SFA) and monounsaturated fatty acids (MUFA) for biodiesel production. Cultivating microalgae in wastewater for biodiesel production can be cost-effective, especially for microalgae adapted to harsh conditions. It could be concluded that O. pusilla is a promising candidate for biodiesel production using wastewater as a growth medium, as it has high biomass productivity and lipid yield, and its fatty acid profile meets the standard values of American and European biodiesel standards. This approach offers a sustainable and environmentally friendly solution for producing biofuels while reducing the environmental impact of wastewater disposal.

Role of family in supporting children with mental disorders in Qatar.

Background: Mental disorders can significantly impact children's lives and affect their emotional, cognitive, and behavioral development. Family support and care is critical to the well-being of children, particularly children with mental disorders. However, given the "gap" between research and practice"," there have been very few studies in the Arab region that focus on the role of the family in supporting children with mental disorders. The study also examines how families cope with caring for a person with mental disorders and what behaviors may influence the patient's distress. In addition, the study will examine the importance of family rehabilitation and integration of people with mental disorders into society. Methods: The study adopts the descriptive-analytical method and uses a questionnaire to gather data from the participants. The 350-parents sample (with 113 boys, 237 girls) was selected from the Shafallah Center for Integrating People with Disability. Morgan's law is used to determine the sample size. Results: The results show that there are statistically significant differences in the role of family members in supporting people with mental disorders due to two variables: Gender and Work. Age has no statistically significant effect on the role of family members in supporting people with mental disorders. Conclusion: This study is the first study conducted to investigate the role of family in supporting children with mental disorders in the Gulf Cooperation Council (GCC) in general and Qatar in particular. The results show that families should cope with the needs of a person with a mental disorder. Family rehabilitation is important in the care of people with mental disorders. There are certain behaviors of family members that can increase or decrease stress for the person. The results suggest that the family plays an essential role in supporting and promoting the lives of people with mental disorders and recommending effective ways to cope with them.

Physical, Metabolic, and Microbial Rumen Development in Goat Kids: A Review on the Challenges and Strategies of Early Weaning.

The digestive system of newborn ruminant functions is similar to monogastric animals, and therefore milk flows into the abomasum instead of rumen for digestion. The rumen undergoes tremendous changes over time in terms of structure, function, and microbiome. These changes contribute to the smooth transition from the dependence on liquid diets to solid diets. Goat kids are usually separated at early ages from their dams in commercial intensive systems. The separation from dams minimizes the transfer of microbiota from dams to newborns. In this review, understanding how weaning times and methodologies could affect the normal development and growth of newborn goats may facilitate the development of new feeding strategies to control stress in further studies.

Intensification and Optimization of FAME Synthesis via Acid-Catalyzed Esterification Using Central Composite Design (CCD).

The acid-catalyzed pre-treatment esterification process is required for low-cost feedstock with high free fatty acids (FFAs) to avoid the saponification that occurs during alkali-catalyzed transesterification for the production of fatty acid alkyl esters (FAAE). Reverse hydrolysis in acid-catalyzed esterification causes a decrease in fatty acid methyl ester (FAME) yield. Therefore, the esterification process must be intensified. This study aims to develop and optimize a low-temperature intensification process to enhance biodiesel yield and reduce energy consumption. Three intensification systems were studied: co-solvent technique, co-solvent coupled with adsorption of water using molecular sieves, and entrainer-based continuous removal of water. The process variables of esterification reaction in co-solvents without the adsorption system were optimized by using central composite design (CCD). The study showed that the co-solvent without the adsorption system was effective in intensifying the FFA conversion (XFFA) at low temperatures, compared to the other two systems, due to the dilution effect at high co-solvent/entrainer amount required for sufficient vapors in the adsorption system. Optimized process variables have achieved 95% XFFA within 75 min at 55 °C, 20 mL/100 g of oil DEE, 9 MR, 3 wt % H2SO4, and 320-350 RPM in a co-solvent without the adsorption system.

Morphological and radiological mapping of dental cusps in relation to spatial constraints on tooth shape of one humped camel (Camelus dromedarius).

A significant extent of researches in veterinary study have been focused on dental structure; however, there are scanty ones on the orientation and identification of their cusps. Therefore, the present article aimed to spot a light on arrangement pattern of dental cusps in the camel as a folivorous and graminivorous animal. This study was conducted on eight heads of adult, healthy camel of both sexes, collected from slaughter houses. To perform exact orientation of cusps of molar teeth, additional radiological and CT scans were performed on the mandible as a landmark that should facilitate the reading of cusps map. It was evident that, the cusps are arranged in crescentic appearance, seledontal form, with two cusps on each side, paracone and hypocone on the lingual surface and protocone and metacone on the vestibular aspect. Thus, camels cannot wear bite like equines, which would interfere with their constant chewing method. The camels' dental cusps provide some of the finest examples of convergent evolution, which offer insights both into correlates between form and function, and into how the ability of euthomorphic cusps in intrapability and stabilization of food items and its comminution between formidable cusps and occlusal spillway in between. Further studies should be done on the brachydontteeth and tropospheric cusps to fill the functional anatomy gap of teeth, in addition to diversity of cusps form. This study is considered a basic comparative anatomical study for normal healthy dentition and forensic practice, in addition to its importance in detection of local aspects of dental problems in camels.

Cyanobacteria as a Valuable Natural Resource for Improved Agriculture, Environment, and Plant Protection.

Taking into consideration, the challenges faced by the environment and agro-ecosystem make increased for suggestions more reliable methods to help increase food security and deal with difficult environmental problems. Environmental factors play a critical role in the growth, development, and productivity of crop plants. Unfavorable changes in these factors, such as abiotic stresses, can result in plant growth deficiencies, yield reductions, long-lasting damage, and even death of the plants. In reflection of this, cyanobacteria are now considered important microorganisms that can improve the fertility of soils and the productivity of crop plants due to their different features like photosynthesis, great biomass yield, ability to fix the atmospheric N2, capability to grow on non-arable lands, and varied water sources. Furthermore, numerous cyanobacteria consist of biologically active substances like pigments, amino acids, polysaccharides, phytohormones, and vitamins that support plant growth enhancement. Many studies have exposed the probable role of these compounds in the alleviation of abiotic stress in crop plants and have concluded with evidence of physiological, biochemical, and molecular mechanisms that confirm that cyanobacteria can decrease the stress and induce plant growth. This review discussed the promising effects of cyanobacteria and their possible mode of action to control the growth and development of crop plants as an effective method to overcome different stresses.

Hazard assessment study on organic compounds and heavy metals from using artificial turf.

Introduction: Artificial turf or synthetic grass releases hazardous substances such as heavy metals, polycyclic aromatic hydrocarbons (PAHs), and volatile organic compounds (VOCs). Objective: The current study aimed to evaluate the concentration levels of hazardous substances that are emitted from artificial turf as a result of sunlight effect; and to assess the expected exposure risks to such emitted substances during various activities.The current study aimed to evaluate the concentration levels of hazardous substances that are emitted from artificial turf as a result of the effect of sunlight. And to assess the expected risks of exposure to these substances emitted during the various activities. Study design: VOCs emitted from artificial turf samples were monitored and collected in the ambient air of three football fields, the ambient air around a piece of new artificial turf that has not yet been used on playing fields, but has been exposed to sunlight within one year and in the indoor air around a piece of new artificial turf. Which has not yet been used on the playgrounds and was placed at room temperature and away from sunlight. Results: The current study shows that average afternoon morning VOCs levels were 277, 333, 405 and 509 mg/m3 in winter, autumn, spring and summer, respectively. The most predominant PAHs compounds present in the samples were compounds with 3-rings and 4-rings.The average daily intake (ADI) for three exposure routes (ingestion, inhalation, and dermal contact) was calculated for different age categories (3-6, 7-15, 16-18, 19-22, 23-55, and 56-70 year). Non-Carcinogenic exposure risk as hazard quotient (HQ) and hazard index (HI) were detected. Conclusion: All HI values were <1, indicating that there is no potential adverse health effects occur as a result of a chemical exposure. Total carcinogenic risk (R) values for the different age categories were higher than 1E-04 for three football artificial grass fields, which indicated a high cancer risk development probability. HI and R probability increased in the age group of 7-15 year > 3-6 years.

Evaluation of Clinical and Biochemical Traits in Egyptian Barki Sheep with Different Growth Performances.

The Barki sheep industry is becoming increasingly important in Egypt because of the high quality of their meat and wool. This sheep breed is also commonly known for its resistance to arid and harsh environmental conditions. Such characteristics can be exploited in solving the problematic situation of inadequate animal protein for human consumption, particularly under climatic changes. However, very few studies have investigated aspects of breeding, nutrition, and susceptibility to infectious or non-infectious diseases in Barki sheep. Herein, we propose to unravel the differences in the clinical and biochemical profiles among Barki sheep of different growth rates. We measured clinical and biochemical parameters in stunted (n = 10; test group) and in good body condition (n = 9; control group) Barki sheep. Animals subjected to this experiment were of the same sex (female), age (12 months old), and housed in the same farm with similar conditions of feeding, management practice, and vaccination and deworming regimens. Regarding clinical examination, stunted/tested sheep showed a significantly higher pulse and respiratory rate compared to sheep with a good body condition/control group. The appetite, body temperature, and digestion processes were the same in both groups. In biochemical investigations, nutritional biomarkers were reduced markedly in stunted sheep compared with the control sheep, including total protein (p = 0.0445), albumin (p = 0.0087), cholesterol (p = 0.0007), and triglycerides (p = 0.0059). In addition, the Barki sheep test group suffered from higher levels of urea and blood urea nitrogen than the control group. Consistently, growth and thyroid hormone levels were lower in stunted sheep than the control sheep, although the differences were not statistically significant (p > 0.05). No significant differences were detected in both groups for serum levels of calcium, phosphorus, magnesium, iron, and zinc (p > 0.05). To detect the reasons for emaciation, certain debilitating infections were tested. All tested sheep showed negative coprological tests for gastrointestinal parasites, and had no obvious seropositivity to brucellosis, toxoplasmosis, neosporosis, or Q fever. This study demonstrates the useful biochemical markers for monitoring growth performance in Egyptian Barki sheep and unravels the usefulness of this breed in nationwide breeding and farming.

The restoration and erection of the world's first elevated obelisk.

Obelisks presented an important element in the architecture of ancient Egypt. This research is concerned with the re-erection of an obelisk that belongs to the famous Pharoah Ramses II. It was found broken and was transported to the Grand Egyptian Museum for restoration and display. An observation of Ramses II Cartouche at the bottom side of the obelisk base inspired the authorities to provide an innovative architectural design to display the obelisk elevated. The supporting structure was designed to allow the visitors to walk underneath the obelisk and observe Ramses II's signature. The idea of elevating the obelisk presented several challenges including evaluating the obelisk's current condition, restoration and fixation methodology, structural stability, and uncertainties of material characteristics, amongst others. To control the obelisk deformations under lateral loading, state-of-the-art base isolators were introduced. For the task to be achieved, a multidisciplinary team including historians, conservators, archaeologists, architects, and engineers with different specialties was appointed. The team performed the task successfully and currently, the obelisk stands at the entrance piazza of the Grand Egyptian Museum representing the world's first elevated obelisk.

Mobility of LoRaWAN Gateways for Efficient Environmental Monitoring in Pristine Sites.

Environmental monitoring of delicate ecosystems or pristine sites is critical to their preservation. The communication infrastructure for such monitoring should have as little impact on the natural ecosystem as possible. Because of their wide range capabilities and independence from heavy infrastructure, low-power wide area network protocols have recently been used in remote monitoring. In this regard, we propose a mobile vehicle-mounted gateway architecture for IoT data collection in communication-network-free areas. The limits of reliable communication are investigated in terms of gateway speed, throughput, and energy consumption. We investigate the performance of various gateway arrival scenarios, focusing on the trade-off between freshness of data, data collection rate, and end-node power consumption. Then we validate our findings using both real-world experiments and simulations. In addition, we present a case study exploiting the proposed architecture to provide coverage for Wadi El-Gemal national park in Egypt. The results show that reliable communication is achieved over all spreading factors (SFs) for gateway speeds up to 150 km/h with negligible performance degradation at SFs=11,12 at speeds more than 100 km/h. The synchronized transmission model ensures the best performance in terms of throughput and power consumption at the expense of the freshness of data. Nonsynchronized transmission allows time-flexible data collection at the expense of increased power consumption. The same throughput as semisynchronized transmission is achieved using four gateways at only five times the energy consumption, while a single gateway requires seventeen times the amount of energy. Furthermore, increasing the number of gateways to ten increases the throughput to the level achieved by the synchronized scenario while consuming eight times the energy.

IDENTIFICATION OF AREAS OF HIGH POTENTIAL-BEARING MINERALIZATIONS, EASTERN DESERT OF EGYPT: INSIGHTS FROM AIRBORNE GAMMA-RAY SPECTROMETRIC DATA.

A major number of mineral deposits are related to hydrothermal processes. Therefore, the mapping of the hydrothermally alteration areas, connected with mineralization, is crucial in the search for metal deposits. To achieve this purpose, areas of hydrothermal alterations are targeted by processing the airborne gamma-ray spectrometric data to detect areas enriched in potassium that may indicate the existence of potassic alteration zones, which are often associated with hydrothermal alterations accompanied by mineral deposits. Data processing and analysis were performed using the K/eTh ratio, deviation of ideal potassium (Kd) and F-parameter. Besides, determining the environmental radiation risk due to the fact that the study area contains many excavation sites for various mining materials and quarries. Hydrothermal alteration indicator maps show five known mineralizations of gold, copper, molybdenum, fluorite and wolframite, which are associated with hydrothermal processes that took place in the study area. It is possible to note the intimate correlation of mineral deposits present in areas with high potassium content. Positive correlation between the computed hydrothermal alteration indicators (K/eTh, Kd and F-parameter), shown on the ternary image map, revealed favorable high and intermediate targets for the detection of various mineral deposits in the study area. On the other hand, the estimated mean values of absorbed dose rate for all rock units were within the permissible range (28-120 nGy h-1), and the mean annual effective dose rate was below the permissible limit of 1.0 mSv y-1 for these rocks.

Effects of 4-phenylbutyric acid on the development of diabetic retinopathy in diabetic rats: regulation of endoplasmic reticulum stress-oxidative activation.

There are good evidences suggesting that endoplasmic reticulum (ER) stress can be one of the contributing factors in the development of diabetic retinopathy. The present study was designed to investigate the effect of chemical chaperone 4-phenylbutyric acid (4-PBA) in alleviating the ER stress, and diabetic retinopathy in type 2 diabetic rats. Treatment of diabetic rats with 4-PBA, increased the antioxidant capacity, reduced the levels of lipid peroxidation, organised the state of apoptosis and regulated the ER stress - oxidative activation in retinal tissue. Also there was an improvement in the histological picture of retinal specimens compared to untreated diabetic rats. It was concluded that 4-PBA is a promising therapeutic agent for ER stress diseases such as diabetic retinopathy.