The balancing act between high electronic and low ionic transport influenced by perovskite grain boundaries.

A better understanding of the materials' fundamental physical processes is necessary to push hybrid perovskite photovoltaic devices towards their theoretical limits. The role of the perovskite grain boundaries is essential to optimise the system thoroughly. The influence of the perovskite grain size and crystal orientation on physical properties and their resulting photovoltaic performance is examined. We develop a novel, straightforward synthesis approach that yields crystals of a similar size but allows the tuning of their orientation to either the (200) or (002) facet alignment parallel to the substrate by manipulating dimethyl sulfoxide (DMSO) and tetrahydrothiophene-1-oxide (THTO) ratios. This decouples crystal orientation from grain size, allowing the study of charge carrier mobility, found to be improved with larger grain sizes, highlighting the importance of minimising crystal disorder to achieve efficient devices. However, devices incorporating crystals with the (200) facet exhibit an s-shape in the current density-voltage curve when standard scan rates are used, which typically signals an energetic interfacial barrier. Using the drift-diffusion simulations, we attribute this to slower-moving ions (mobility of 0.37 × 10-10 cm2 V-1 s-1) in combination with a lower density of mobile ions. This counterintuitive result highlights that reducing ion migration does not necessarily minimise hysteresis.

Precursor Engineering of Lead Acetate-Based Precursors for High-Open-Circuit Voltage Wide-Bandgap Perovskite Solar Cells.

Wide-bandgap (WBG) perovskites have great potential for inclusion in efficient tandem solar cells, but large open-circuit voltage losses have limited device performance to date. Here, we show that a high-quality WBG perovskite, FA0.83Cs0.17Pb(I0.8Br0.2)3, with enlarged grain sizes and improved crystallinity can be achieved by incorporating lead chloride (PbCl2) into a lead acetate (PbAc2)-based precursor. The improved film quality resulted in the suppression of nonradiative recombination and a reduction in defect density. Efficient WBG perovskite solar cells (1.66 eV) with an efficiency of 19.3% and a high Voc of 1.22 V were fabricated using a facile one-step spin-coating method without the need for an antisolvent. Notably, the unencapsulated devices retained 90% of their initial power conversion efficiency after storage in a dry box (10% humidity) for 800 h.

Enhanced Carrier Diffusion Enables Efficient Back-Contact Perovskite Photovoltaics.

Back-contact architectures offer a promising route to improve the record efficiencies of perovskite solar cells (PSCs) by eliminating parasitic light absorption. However, the performance of back-contact PSCs is limited by inadequate carrier diffusion in perovskite. Here, we report that perovskite films with a preferred out-of-plane orientation show improved carrier dynamic properties. With the addition of guanidine thiocyanate, the films exhibit carrier lifetimes and mobilities increased by 3-5 times, leading to diffusion lengths exceeding 7 µm. The enhanced carrier diffusion results from substantial suppression of nonradiative recombination and improves charge collection. Devices using such films achieve reproducible efficiencies reaching 11.2 %, among the best performances for back-contact PSCs. Our findings demonstrate the impact of carrier dynamics on back-contact PSCs and provide the basis for a new route to high-performance back-contact perovskite optoelectronic devices at low cost.

Intermediate-phase engineering via dimethylammonium cation additive for stable perovskite solar cells.

Achieving the long-term stability of perovskite solar cells is arguably the most important challenge required to enable widespread commercialization. Understanding the perovskite crystallization process and its direct impact on device stability is critical to achieving this goal. The commonly employed dimethyl-formamide/dimethyl-sulfoxide solvent preparation method results in a poor crystal quality and microstructure of the polycrystalline perovskite films. In this work, we introduce a high-temperature dimethyl-sulfoxide-free processing method that utilizes dimethylammonium chloride as an additive to control the perovskite intermediate precursor phases. By controlling the crystallization sequence, we tune the grain size, texturing, orientation (corner-up versus face-up) and crystallinity of the formamidinium (FA)/caesium (FA)yCs1-yPb(IxBr1-x)3 perovskite system. A population of encapsulated devices showed improved operational stability, with a median T80 lifetime (the time over which the device power conversion efficiency decreases to 80% of its initial value) for the steady-state power conversion efficiency of 1,190 hours, and a champion device showed a T80 of 1,410 hours, under simulated sunlight at 65 °C in air, under open-circuit conditions. This work highlights the importance of material quality in achieving the long-term operational stability of perovskite optoelectronic devices.

Intensity Modulated Photocurrent Microspectrosopy for Next Generation Photovoltaics.

In this report, a large-area laser beam induced current microscope that has been adapted to perform intensity modulated photocurrent spectroscopy (IMPS) in an imaging mode is described. Microscopy-based IMPS method provides a spatial resolution of the frequency domain response of the solar cell, allowing correlation of the optoelectronic response with a particular interface, bulk material, specific transport layer, or transport parameter. The system is applied to study degradation effects in back-contact perovskite cells where it is found to readily differentiate areas based on their markedly different frequency response. Using the diffusion-recombination model, the IMPS response is modeled for a sandwich structure and extended for the special case of lateral diffusion in a back-contact cell. In the low-frequency limit, the model is used to calculate spatial maps of the carrier ambipolar diffusion length. The observed frequency response of IMPS images is then discussed.

Self-Enhancement of Efficiency and Self-Attenuation of Hysteretic Behavior of Perovskite Solar Cells with Aging.

Spontaneous enhancement of the photovoltaic performance of perovskite solar cells (PSCs) after aging has been reported, but the underlying reasons for such behavior are still under debate. Herein, we demonstrate that this spontaneous improvement effect accompanied by self-attenuation of hysteresis in the current-voltage characteristics is time- and temperature-dependent. Moreover, it is universal to PSCs based on a range of mixed-ion perovskites and coupled to different hole- and electron-transporting materials. Time-resolved confocal fluorescence microscopy and other characterization techniques suggest that the "self-healing" phenomenon is accompanied by the homogenization and enhancement of the charge extraction efficiency as well as suppressed recombination throughout cm2-scale perovskite layers. These dynamic effects need to be accounted for when assessing the initial and stabilized performance of PSCs.

Light-induced reversal of ion segregation in mixed-halide perovskites.

Bandgap instability due to light-induced phase segregation in mixed-halide perovskites presents a major challenge for their future commercial use. Here we demonstrate that photoinduced halide-ion segregation can be completely reversed at sufficiently high illumination intensities, enabling control of the optical bandgap of a mixed-halide perovskite single crystal by optimizing the input photogenerated carrier density. We develop a polaron-based two-dimensional lattice model that rationalizes the experimentally observed phenomena by assuming that the driving force for photoinduced halide segregation is dependent on carrier-induced strain gradients that vanish at high carrier densities. Using illumination sources with different excitation intensities, we demonstrate write-read-erase experiments showing that it is possible to store information in the form of latent images over several minutes. The ability to control the local halide-ion composition with light intensity opens opportunities for the use of mixed-halide perovskites in concentrator and tandem solar cells, as well as in high-power light-emissive devices and optical memory applications.

Synergistic Effect of N,N-Dimethylformamide and Hydrochloric Acid on the Growth of MAPbI3 Perovskite Films for Solar Cells.

Perovskite solar cells have emerged as a promising next-generation electrical power generating tool. However, imperfections in perovskite films are one of the crucial factors preventing the commercialization of perovskite solar cells. Passivation has proven to be an effective strategy to reduce the density of defect states in perovskite crystals and inhibit ion migration. Although significant work on chloride ion and N,N-dimethylformamide (DMF) has shown that the additives are able to passivate different types of trap defects, systematic studies on the effects of DMF and HCl on perovskite crystallization when used in conjunction with each other are elusive. Here, we systematically investigated the synergistic effect of DMF and hydrochloric acid (HCl) on methylammonium (MA+)-based perovskite films with the two-step spin-coating method. As a Lewis base, DMF coordinates well with Pb2+ to facilitate a decrease in the number of defects, thereby improving the carrier separation and transport, while HCl improves the overall perovskite film morphology. Addition of 20 µL HCl/20 µL DMF to 10 mL of methylammonium iodide/isopropyl alcohol solution afforded ca. 500 nm thick perovskite films with no observable defects within the grains. The process allowed fabrication of devices with an active area of 0.16 cm2, which produced power conversion efficiencies up to 18.37% with minimal hysteresis.

Solution-processed antireflective coating for back-contact perovskite solar cells.

Back-contact architectures for perovskite solar cells eliminate parasitic-absorption losses caused by the electrode and charge collection layers but increase surface reflection due to the high refractive index mismatch at the air/perovskite interface. To mitigate this, a ∼85 nm thick layer of poly(methyl methacrylate) (PMMA), with a refractive index between those of air and perovskite, has been applied as an antireflective coating. Transfer matrix modelling is used to determine the ideal PMMA layer thickness, with UV-Vis spectroscopy measurements used to confirm the increase in absorption that arises through the application of the antireflective coating. The deposition of a thin film of PMMA via spin coating onto a solar cell results in a 20-30% relative increase in short circuit current density and stable power output density.

Solution-Processed Faraday Rotators Using Single Crystal Lead Halide Perovskites.

Lead halide perovskites (LHPs) have become a promising alternative for a wide range of optoelectronic devices, thanks to their solution-processability and impressive optical and electrical properties. More recently, LHPs have been investigated in magneto-optic studies and have exhibited spin-polarized emission, photoinduced magnetization, and long spin lifetimes. Here, the viability of methylammonium lead bromide (MAPbBr3) single crystals as solution-processed Faraday rotators is demonstrated. Compared to terbium gallium garnet, the industry standard in the visible, it is found that MAPbBr3 exhibits Verdet constants (i.e., strength of Faraday effect) of similar or greater magnitude (up to 2.5x higher), with lower temperature dependence. Due to its low trap absorption, it is calculated that an optical isolator made from MAPbBr3, with appropriate antireflection coatings, should reach ≈95% transmission and achieve 40 dB isolation for incoming powers of over 2 W. It is also shown that the Verdet constant of MAPbBr3 can be calculated accurately from its dispersion in refractive index, allowing the possibility to predict similar effects in other perovskite materials.

Solvent Engineering of a Dopant-Free Spiro-OMeTAD Hole-Transport Layer for Centimeter-Scale Perovskite Solar Cells with High Efficiency and Thermal Stability.

High efficiency and environmental stability are mandatory performance requirements for commercialization of perovskite solar cells (PSCs). Herein, efficient centimeter-scale PSCs with improved stability were achieved by incorporating an additive-free 2,2',7,7'-tetrakis[N,N-di(p-methoxyphenyl)amino]-9,9'-spirobifluorene (spiro-OMeTAD) hole-transporting material (HTM) through simply substituting the usual chlorobenzene solvent with pentachloroethane (PC). A stabilized power conversion efficiency (PCE) of 16.1% under simulated AM 1.5G 1 sun illumination with an aperture of 1.00 cm2 was achieved for PSCs using an additive-free spiro-OMeTAD layer cast from PC. X-ray analysis suggested that chlorine radicals from PC transfer partially to spiro-OMeTAD and are retained in the HTM layer, resulting in conductivity improvement. Moreover, unencapsulated PSCs with a centimeter-scale active area cast from PC retained >70% of their initial PCE after ageing at 80 °C for 500 h, in contrast with less than 20% retention for control devices. Morphological and X-ray analyses of the aged cells revealed that the perovskite and HTM layers remain almost unchanged in the cells with a spiro-OMeTAD layer cast from PC whereas serious degradation occurred in the control cells. This study not only reveals the decomposition mechanism of PSCs in the presence of HTM additives but also opens up a broad range of organic semiconductors for radical doping.

High Efficiency Mesoscopic Solar Cells Using CsPbI3 Perovskite Quantum Dots Enabled by Chemical Interface Engineering.

All-inorganic α-CsPbI3 perovskite quantum dots (QDs) are attracting great interest as solar cell absorbers due to their appealing light harvesting properties and enhanced stability due to the absence of volatile organic constituents. Moreover, ex situ synthesized QDs significantly reduce the variability of the perovskite layer deposition process. However, the incorporation of α-CsPbI3 QDs into mesoporous TiO2 (m-TiO2) is highly challenging, but these constitute the best performing electron transport materials in state-of-the-art perovskite solar cells. Herein, the m-TiO2 surface is engineered using an electron-rich cesium-ion containing methyl acetate solution. As one effect of this treatment, the solid-liquid interfacial tension at the TiO2 surface is reduced and the wettability is improved, facilitating the migration of the QDs into m-TiO2. As a second effect, Cs+ ions passivate the QD surface and promote the charge transfer at the m-TiO2/QD interface, leading to an enhancement of the electron injection rate by a factor of 3. In combination with an ethanol-environment smoothing route that significantly reduces the surface roughness of the m-TiO2/QD layer, optimized devices exhibit highly reproducible power conversion efficiencies exceeding 13%. The best cell with an efficiency of 14.32% (reverse scan) reaches a short-circuit current density of 17.77 mA cm-2, which is an outstanding value for QD-based perovskite solar cells.

Alkali Cation Doping for Improving the Structural Stability of 2D Perovskite in 3D/2D PSCs.

3D/2D hybrid perovskite systems have been intensively investigated to improve the stability of perovskite solar cells (PSCs), whereas undesired crystallization of 2D perovskite during the film formation process could undermine the structural stability of 2D perovskite materials, which causes serious hysteresis of PSCs after aging. This issue is, however, rarely studied. The stability study for 3D/2D hybrid systems to date is all under the one-direction scan, and the lack of detailed information on the hysteresis after aging compromises the credibility of the stability results. In this work, by correlating the hysteresis of the hybrid PSCs with the 2D crystal structure, we find that the prompt 2D perovskite formation process easily induces numerous crystal imperfections and structural defects. These defects are susceptible to humidity attack and decompose the 2D perovskite to insulating long-chain cations and 3D perovskite, which hinder charge transfer or generate charge accumulation. Therefore, a large hysteresis is exhibited after aging the 3D/2D hybrid PSCs in an ambient environment, even though the reverse-scan power conversion efficiency (PCE) is found to be well-preserved. To address this issue, alkali cations, K+ and Rb+, are introduced into the 2D perovskite to exquisitely modulate the crystal formation, which gives rise to a higher crystallinity of 2D perovskite and a better film morphology with fewer defects. We achieved PCE beyond 21% due to the preferable charge transfer process and reduced nonradiative recombination losses. The structural features also bring about impressive moisture stability, which results in the corresponding PSCs retaining 93% of its initial PCE and negligible hysteresis after aging in an ambient atmosphere for 1200 h.

Unique Layer-Doping-Induced Regulation of Charge Behavior in Metal-Free Carbon Nitride Photoanodes for Enhanced Performance.

Photoinduced charge carrier behavior is critical in determining photoelectrocatalytic activity. In this study, a unique layer-doped metal-free polymeric carbon nitride (C3 N4 ) photoanode is fabricated by using one-pot thermal vapor deposition. With this method, a photoanode consisting of a phosphorus-doped top layer, boron-doped middle layer, and pristine C3 N4 bottom layer, was formed as a result of the difference in thermal polymerization kinetics associated with the boron-containing H3 BO3 -melamine complex and the phosphorus-containing H3 PO4 -dicyandiamide complex. This layer-doping fabrication strategy effectively contributes to the formation of dual junctions that optimizing charge carrier behavior. The ternary-layer C3 N4 photoanode exhibits significantly enhanced photoelectrochemical water oxidation activity compared to pristine C3 N4 , with a record photocurrent density of 150±10 µA cm-2 at 1.23 V vs. RHE. This layer-doping strategy provides an effective means for design and fabrication of photoelectrodes for solar water oxidation.

Self-assembly of spherical and rod-shaped nanoparticles with full positional control.

The controlled positioning of spherical gold nanoparticles and gold nanorods upon self-assembly on a substrate is of great interest for the fabrication of tailored plasmonic devices. Here, an electrostatic approach with a sequential two-step assembly protocol is presented as a cost-effective and high-yield alternative to previously presented, more complex proof of concepts. Three different geometries can be separately produced in large quantities relying on electrostatic attraction and repulsion of the charge-carrying building blocks: a single gold nanoparticle at the tip, the side or on top of a gold nanorod. DLVO theory is used to explain the electrostatic assembly strategy. The process is highly efficient and assembly yields between 79% (at the tip) and 94% (for the nanoparticle at the long side of the nanorod) are achieved.

Multiple Roles of Cobalt Pyrazol-Pyridine Complexes in High-Performing Perovskite Solar Cells.

Chemical doping is a ubiquitously applied strategy to improve the charge-transfer and conductivity characteristics of spiro-OMeTAD, a hole-transporting material (HTM) used widely in solution-processed perovskite solar cells (PSCs). Cobalt(III) complexes are commonly employed HTM dopants, whose major role is to oxidize spiro-OMeTAD to provide p-doping for improved conductivity. The present work discloses additional, previously unknown important functions of cobalt complexes in the HTM films that influence the photovoltaic performance. Specifically, it is demonstrated that commercial p-dopant FK269 (bis(2,6-di(1H-pyrazol-1-yl)pyridine) cobalt(III) tris(bis(trifluoromethylsulfonyl)imide)) reduces the interfacial recombination and alleviates the decomposition of the perovskite layer under the action of tert-butylpyridine and lithium bis(trifluoromethanesulfonyl)imide. These effects are demonstrated for 1 cm2 perovskite solar cells that achieve a stabilized power conversion efficiency of 19% under 1 sun irradiation.

The optical properties of Cs4PbBr6-CsPbBr3 perovskite composites.

Although the optoelectronic applications of metal halide perovskites have been intensively investigated in recent years, the fundamental carrier dynamics of zero-dimensional (0D) Cs4PbBr6 perovskites has been relatively underexplored; in particular, the nature of the green fluorescence is highly debated. Nevertheless, the unique photophysical properties are of immense interest for a variety of potential applications. In this work, the green emission of the CsPbBr3-Cs4PbBr6 perovskite composites is studied using temperature dependent photoluminescence (PL). The PL spectra at different temperatures simultaneously contain two sub-peaks (520 nm and 550 nm), which are ascribed to the emissions of the band-edge and the defect trapped exciton of CsPbBr3. This finding will help to understand the controversial photoluminescence currently observed in different 0D Cs4PbBr6 perovskites.

Phase controlled SERS enhancement.

Surface-enhanced Raman spectroscopy (SERS) has attracted increasing interest for chemical and biochemical sensing. Several studies have shown that SERS intensities are significantly increased when an optical interference substrate composed of a dielectric spacer and a reflector is used as a supporting substrate. However, the origin of this additional enhancement has not been systematically studied. In this paper, high sensitivity SERS substrates composed of self-assembled core-satellite nanostructures and silica-coated silicon interference layers have been developed. Their SERS enhancement is shown to be a function of the thickness of silica spacer on a more reflective silicon substrate. Finite difference time domain modeling is presented to show that the SERS enhancement is due to a spacer contribution via a sign change of the reflection coefficients at the interfaces. The magnitude of the local-field enhancement is defined by the interference of light reflected from the silica-air and silica-silicon interfaces, which constructively added at the hot spots providing a possibility to maximize intensity in the nanogaps between the self-assembled nanoparticles by changing the thickness of silica layer. The core-satellite assemblies on a 135 nm silica-coated silicon substrate exhibit a SERS activity of approximately 13 times higher than the glass substrate.

Dual Quantum Dot-Decorated Bismuth Vanadate Photoanodes for Highly Efficient Solar Water Oxidation.

Photo-induced charge separation and photon absorption play important roles in determining the performance of the photoelectrocatalytic water splitting process. In this work, we utilize dual quantum dots (QDs), consisting of BiVO4 and carbon, to fabricate a hybrid homojunction-based BiVO4 photoanode for efficient and stable solar water oxidation. Formation of homojunctions, by decorating as-prepared BiVO4 substrate with BiVO4 QDs, enhances the charge separation efficiency by 1.3 times. This enhancement originates from lattice match, which benefits charge transfer across the interface. Furthermore, the use of carbon QDs as a stable photosensitizer effectively extends the photon absorption limit from 520 nm to over 700 nm, yielding an incident photon-to-electron conversion efficiency of 6.0 %, even at 600 nm at 1.23 V versus RHE. Finally, a remarkable photocurrent density of 6.1 mA cm-2 at 1.23 V was recorded after depositing FeOOH/NiOOH as cocatalysts, thereby, reaching 82 % of the theoretical efficiency for BiVO4 .

Visualizing Phase Segregation in Mixed-Halide Perovskite Single Crystals.

Mixed organolead halide perovskites (MOHPs), CH3 NH3 Pb(Brx I1-x )3 , have been shown to undergo phase segregation into iodide-rich domains under illumination, which presents a major challenge to their development for photovoltaic and light-emitting devices. Recent work suggested that phase-segregated domains are localized at crystal boundaries, driving investigations into the role of edge structure and the growth of larger crystals with reduced surface area. Herein, a method for growing large (30×30×1 µm3 ) monocrystalline MAPb(Brx I1-x )3 single crystals is presented. The direct visualization of the growth of nanocluster-like I-rich domains throughout the entire crystal revealed that grain boundaries are not required for this transformation. Narrowband fluorescence imaging and time-resolved spectroscopy provided new insight into the nature of the phase-segregated domains and the collective impact on the optoelectronic properties.