Enhancing grid resiliency in distributed energy systems through a comprehensive review and comparative analysis of islanding detection methods.

Reduction of fossil fuel usage, clean energy supply, and dependability are all major benefits of integrating distributed energy resources (DER) with electrical utility grid (UG). Nevertheless, there are difficulties with this integration, most notably accidental islanding that puts worker and equipment safety at risk. Islanding detection methods (IDMs) play a critical role in resolving this problem. All IDMs are thoroughly evaluated in this work, which divides them into two categories: local approaches that rely on distributed generation (DG) side monitoring and remote approaches that make use of communication infrastructure. The study offers a comparative evaluation to help choose the most efficient and applicable IDM, supporting well-informed decision-making for the safe and dependable operation of distributed energy systems within electrical distribution networks. IDMs are evaluated based on NDZ outcomes, detection duration, power quality impact, multi-DG operation, suitability, X/R ratio reliance, and efficient functioning.

Enhancing Ethiopian power distribution with novel hybrid renewable energy systems for sustainable reliability and cost efficiency.

Economic development relies on access to electrical energy, which is crucial for society's growth. However, power shortages are challenging due to non-renewable energy depletion, unregulated use, and a lack of new energy sources. Ethiopia's Debre Markos distribution network experiences over 800 h of power outages annually, causing financial losses and resource waste on diesel generators (DGs) for backup use. To tackle these concerns, the present study suggests a hybrid power generation system, which combines solar and biogas resources, and integrates Superconducting Magnetic Energy Storage (SMES) and Pumped Hydro Energy Storage (PHES) technologies into the system. The study also thoroughly analyzes the current and anticipated demand connected to the distribution network using a backward/forward sweep load flow analysis method. The results indicate that the total power loss has reached its absolute maximum, and the voltage profiles of the networks have dropped below the minimal numerical values recommended by the Institute of Electrical and Electronics Engineers (IEEE) standards (i.e., 0.95-1.025 p.u.). After reviewing the current distribution network's operation, additional steps were taken to improve its effectiveness, using metaheuristic optimization techniques to account for various objective functions and constraints. In the results section, it is demonstrated that the whale optimization algorithm (WOA) outperforms other metaheuristic optimization techniques across three important objective functions: financial, reliability, and greenhouse gas (GHG) emissions. This comparison is based on the capability of the natural selection whale optimization algorithm (NSWOA) to achieve the best possible values for four significant metrics: Cost of Energy (COE), Net Present Cost (NPC), Loss of Power Supply Probability (LPSP), and GHG Emissions. The NSWOA achieved optimal values for these metrics, namely 0.0812 €/kWh, 3.0017 × 106 €, 0.00875, and 7.3679 × 106 kg reduced, respectively. This is attributable to their thorough economic, reliability, and environmental evaluation. Finally, the forward/backward sweep load flow analysis employed during the proposed system's integration significantly reduced the impact of new energy resources on the distribution network. This was evident in the reduction of total power losses from 470.78 to 18.54 kW and voltage deviation from 6.95 to 0.35 p.u., as well as the voltage profile of the distribution system being swung between 1 and 1.0234 p.u., which now comply with the standards set by the IEEE. Besides, a comparison of the cost and GHG emission efficiency of the proposed hybrid system with existing (grid + DGs) and alternative (only DGs) scenarios was done. The findings showed that, among the scenarios examined, the proposed system is the most economical and produces the least amount of GHG emissions.

Optimization of off-grid hybrid renewable energy systems for cost-effective and reliable power supply in Gaita Selassie Ethiopia.

This paper explores scenarios for powering rural areas in Gaita Selassie with renewable energy plants, aiming to reduce system costs by optimizing component numbers to meet energy demands. Various scenarios, such as combining solar photovoltaic (PV) with pumped hydro-energy storage (PHES), utilizing wind energy with PHES, and integrating a hybrid system of PV, wind, and PHES, have been evaluated based on diverse criteria, encompassing financial aspects and reliability. To achieve the results, meta-heuristics such as the Multiobjective Gray wolf optimization algorithm (MOGWO) and Multiobjective Grasshopper optimization algorithm (MOGOA) were applied using MATLAB software. Moreover, optimal component sizing has been investigated utilizing real-time assessment data and meteorological data from Gaita Sillasie, Ethiopia. Metaheuristic optimization techniques were employed to pinpoint the most favorable loss of power supply probability (LPSP) with the least cost of energy (COE) and total life cycle cost (TLCC) for the hybrid system, all while meeting operational requirements in various scenarios. The Multi-Objective Grey Wolf Optimization (MOGWO) technique outperformed the Multi-Objective Grasshopper Optimization Algorithm (MOGOA) in optimizing the problem, as suggested by the results. Furthermore, based on MOGWO findings, the hybrid solar PV-Wind-PHES system demonstrated the lowest COE (0.126€/kWh) and TLCC (€6,897,300), along with optimal satisfaction of the village's energy demand and LPSP value. In the PV-Wind-PHSS scenario, the TLCC and COE are 38%, 18%, 2%, and 1.5% lower than those for the Wind-PHS and PV-PHSS scenarios at LPSP 0%, according to MOGWO results. Overall, this research contributes valuable insights into the design and implementation of sustainable energy solutions for remote communities, paving the way for enhanced energy access and environmental sustainability.

No safe time window in malrotation and volvulus: A consecutive cohort study.

BACKGROUND: Malrotation and volvulus classically present with bilious vomiting. It is more common earlier in life, but there are other causes of bile-stained vomiting. This leads some clinicians to 'watch and wait'. In the presence of a volvulus, this is potentially a fatal decision. It is not clear from the literature if there is a safe time window in which children can be observed in the hope of avoiding transfers or radiological investigations. AIM: To determine whether time to identification and management of midgut volvulus correlated with morbidity and mortality; and whether there were patterns to transition of care. METHODS: Multicentre, retrospective review of all children with malrotation ± volvulus at two tertiary children's hospitals in Brisbane from 2000 to 2012. Data collected included age at presentation, timing between symptom onset and presentation, radiological findings, and definitive surgical management. Outcomes included patient length of stay (LOS), total parenteral nutrition (TPN) duration, re-operations and death. RESULTS: There were 96 cases of malrotation identified, with 23 excluded (elective operation, insufficient data). Neonates made up 66% of included cases. Only 14% of cases were over 12 months old. Bilious vomiting or bile-stained aspirates were the presenting symptoms in 71% (52). Overall mortality was 5.56%. Time from symptom onset to presentation or management was not significantly associated with morbidity or mortality. More than half (53%, 39/73) of patients received total parenteral nutrition; 20/39 for more than 10 days. Neonates and infants had a significantly higher rate of TPN compared with older children (P < 0.001). Those requiring TPN post-operatively had a significantly higher mortality compared with those who did not (P = 0.02). Time from symptom onset to presentation or definitive management was not significantly associated with LOS, TPN duration, or need for re-operation. CONCLUSION: Malrotation remains a time-critical diagnosis to secure and treat. Even a short duration of symptoms can be associated with high morbidity or mortality. There is no place for 'watch and wait' for such patients, and malrotation/volvulus should be emergently actively excluded with contrast studies.

A pareto strategy based on multi-objective optimal integration of distributed generation and compensation devices regarding weather and load fluctuations.

In this study, we present a comprehensive optimization framework employing the Multi-Objective Multi-Verse Optimization (MOMVO) algorithm for the optimal integration of Distributed Generations (DGs) and Capacitor Banks (CBs) into electrical distribution networks. Designed with the dual objectives of minimizing energy losses and voltage deviations, this framework significantly enhances the operational efficiency and reliability of the network. Rigorous simulations on the standard IEEE 33-bus and IEEE 69-bus test systems underscore the effectiveness of the MOMVO algorithm, demonstrating up to a 47% reduction in energy losses and up to a 55% improvement in voltage stability. Comparative analysis highlights MOMVO's superiority in terms of convergence speed and solution quality over leading algorithms such as the Multi-Objective Jellyfish Search (MOJS), Multi-Objective Flower Pollination Algorithm (MOFPA), and Multi-Objective Lichtenberg Algorithm (MOLA). The efficacy of the study is particularly evident in the identification of the best compromise solutions using MOMVO. For the IEEE 33 network, the application of MOMVO led to a significant 47.58% reduction in daily energy loss and enhanced voltage profile stability from 0.89 to 0.94 pu. Additionally, it realized a 36.97% decrease in the annual cost of energy losses, highlighting substantial economic benefits. For the larger IEEE 69 network, MOMVO achieved a remarkable 50.15% reduction in energy loss and improved voltage profiles from 0.89 to 0.93 pu, accompanied by a 47.59% reduction in the annual cost of energy losses. These results not only confirm the robustness of the MOMVO algorithm in optimizing technical and economic efficiencies but also underline the potential of advanced optimization techniques in facilitating the sustainable integration of renewable energy resources into existing power infrastructures. This research significantly contributes to the field of electrical distribution network optimization, paving the way for future advancements in renewable energy integration and optimization techniques for enhanced system efficiency, reliability, and sustainability.

Coordinated power management strategy for reliable hybridization of multi-source systems using hybrid MPPT algorithms.

This research discusses the solar and wind sourcesintegration in aremote location using hybrid power optimization approaches and a multi energy storage system with batteries and supercapacitors. The controllers in PV and wind turbine systems are used to efficiently operate maximum power point tracking (MPPT) algorithms, optimizing the overall system performance while minimizing stress on energy storage components. More specifically, on PV generator, the provided method integrating the Perturb & Observe (P&O) and Fuzzy Logic Control (FLC) methods. Meanwhile, for the wind turbine, the proposed approach combines the P&O and FLC methods. These hybrid MPPT strategies for photovoltaic (PV) and wind turbine aim to optimize its operation, taking advantage of the complementary features of the two methods. While the primary aim of these hybrid MPPT strategies is to optimize both PV and wind turbine, therefore minimizing stress on the storage system, they also aim to efficiently supply electricity to the load. For storage, in this isolated renewable energy system, batteries play a crucial role due to several specific benefits and reasons. Unfortunately, their energy density is still relatively lower compared to some other forms of energy storage. Moreover, they have a limited number of charge-discharge cycles before their capacity degrades significantly. Supercapacitors (SCs) provide significant advantages in certain applications, particularly those that need significant power density, quick charging and discharging, and long cycle life. However, their limitations, such as lower energy density and specific voltage requirements, make them most effective when combined with other storage technologies, as batteries. Furthermore, their advantages are enhanced, result a more dependable and cost-effective hybrid energy storage system (HESS). The paper introduces a novel algorithm for power management designed for an efficient control. Moreover, it focuses on managing storage systems to keep their state of charge (SOC) within defined range. The algorithm is simple and effective. Furthermore, it ensures the longevity of batteries and SCs while maximizing their performance. The results reveal that the suggested method successfully keeps the limits batteries and SCs state of charge (SOC). To show the significance of system design choices and the impact on the battery's SOC, which is crucial for the longevity and overall performance of the energy storage components, a comparison in of two systems have been made. A classical system with one storage (PV/wind turbine/batteries) and the proposed system with HESS (PV/wind turbine system with batteries). The results show that the suggested scenario investigated with both wind and solar resources appears to be the optimum solution for areas where the two resources are both significant and complementary. The balance between the two resources seems to contribute to less stress on storage components, potentially leading to a longer lifespan. An economical study has been made, using the Homer Pro software, to show the feasibility of the proposed system in the studied area.

Performance and robustness analysis of V-Tiger PID controller for automatic voltage regulator.

This paper presents a comprehensive study on the implementation and analysis of PID controllers in an automated voltage regulator (AVR) system. A novel tuning technique, Virtual Time response-based iterative gain evaluation and re-design (V-Tiger), is introduced to iteratively adjust PID gains for optimal control performance. The study begins with the development of a mathematical model for the AVR system and initialization of PID gains using the Pessen Integral Rule. Virtual time-response analysis is then conducted to evaluate system performance, followed by iterative gain adjustments using Particle Swarm Optimization (PSO) within the V-Tiger framework. MATLAB simulations are employed to implement various controllers, including the V-Tiger PID controller, and their performance is compared in terms of transient response, stability, and control signal generation. Robustness analysis is conducted to assess the system's stability under uncertainties, and worst-case gain analysis is performed to quantify robustness. The transient response of the AVR with the proposed PID controller is compared with other heuristic controllers such as the Flower Pollination Algorithm, Teaching-Learning-based Optimization, Pessen Integral Rule, and Zeigler-Nichols methods. By measuring the peak closed-loop gain of the AVR with the controller and adding uncertainty to the AVR's field exciter and amplifier, the robustness of proposed controller is determined. Plotting the performance degradation curves yields robust stability margins and the accompanying maximum uncertainty that the AVR can withstand without compromising its stability or performance. Based on the degradation curves, robust stability margin of the V-Tiger PID controller is estimated at 3.5. The worst-case peak gains are also estimated using the performance degradation curves. Future research directions include exploring novel optimization techniques for further enhancing control performance in various industrial applications.

Enhancing grid-connected photovoltaic system performance with novel hybrid MPPT technique in variable atmospheric conditions.

This paper proposes an innovative approach to improve the performance of grid-connected photovoltaic (PV) systems operating in environments with variable atmospheric conditions. The dynamic nature of atmospheric parameters poses challenges for traditional control methods, leading to reduced PV system efficiency and reliability. To address this issue, we introduce a novel integration of fuzzy logic and sliding mode control methodologies. Fuzzy logic enables the PV system to effectively handle imprecise and uncertain atmospheric data, allowing for decision-making based on qualitative inputs and expert knowledge. Sliding mode control, known for its robustness against disturbances and uncertainties, ensures stability and responsiveness under varying atmospheric conditions. Through the integration of these methodologies, our proposed approach offers a comprehensive solution to the complexities posed by real-world atmospheric dynamics. We anticipate applications in grid-connected PV systems across various geographical locations and climates. By harnessing the synergistic benefits of fuzzy logic and sliding mode control, this approach promises to significantly enhance the performance and reliability of grid-connected PV systems in the presence of variable atmospheric conditions. On the grid side, both PSO (Particle Swarm Optimization) and GA (Genetic Algorithm) algorithms were employed to tune the current controller of the PI (Proportional-Integral) current controller (inverter control). Simulation results, conducted using MATLAB Simulink, demonstrate the effectiveness of the proposed hybrid MPPT technique in optimizing the performance of the PV system. The technique exhibits superior tracking efficiency, achieving a convergence time of 0.06 s and an efficiency of 99.86%, and less oscillation than the classical methods. The comparison with other MPPT techniques highlights the advantages of the proposed approach, including higher tracking efficiency and faster response times. The simulation outcomes are analyzed and demonstrate the effectiveness of the proposed control strategies on both sides (the PV array and the grid side). Both PSO and GA offer effective methods for tuning the parameters of a PI current controller. According to considered IEEE standards for low-voltage networks, the total current harmonic distortion values (THD) obtained are considerably high (8.33% and 10.63%, using the PSO and GA algorithms, respectively). Comparative analyses with traditional MPPT methods demonstrate the superior performance of the hybrid approach in terms of tracking efficiency, stability, and rapid response to dynamic changes.

Advanced efficient energy management strategy based on state machine control for multi-sources PV-PEMFC-batteries system.

This article offers a PV-PEMFC-batteries energy management strategy (EMS) that aims to meet the following goals: keep the DC link steady at the standard value, increase battery lifespan, and meet power demand. The suggested multi-source renewable system (MSRS) is made to meet load demand while using extra power to fill batteries. The major energy source for the MSRS is photovoltaic, and fuzzy logic MPPT is used to guarantee that the PV operates at optimal efficiency under a variety of irradiation conditions. The suggested state machine control consists of 15 steps. It prioritizes the proton exchange membrane fuel cell (PEMFC) as a secondary source for charging the battery when power is abundant and the state of charge (SOC) is low. The MSRS is made feasible by meticulously coordinating control and power management. The MSRS is made achievable by carefully orchestrated control and electricity management. The efficacy of the proposed system was evaluated under different solar irradiance and load conditions. The study demonstrates that implementing the SMC led to an average improvement of 2.3% in the overall efficiency of the system when compared to conventional control techniques. The maximum efficiency was observed when the system was operating under high load conditions, specifically when the state of charge (SOC) was greater than the maximum state of charge (SOCmax). The average efficiency achieved under these conditions was 97.2%. In addition, the MSRS successfully maintained power supply to the load for long durations, achieving an average sustained power of 96.5% over a period of 7.5 s. The validity of the modeling and management techniques mentioned in this study are confirmed by simulation results utilizing the MATLAB/Simulink (version: 2016, link: https://in.mathworks.com/products/simulink.html ) software tools. These findings show that the proposed SMC is effective at managing energy resources in MSRS, resulting in improved system efficiency and reliability.

Optimal sizing and location of grid-interfaced PV, PHES, and ultra capacitor systems to replace LFO and HFO based power generations.

The impacts of climate change, combined with the depletion of fossil fuel reserves, are forcing human civilizations to reconsider the design of electricity generation systems to gradually and extensively incorporate renewable energies. This study aims to investigate the technical and economic aspects of replacing all heavy fuel oil (HFO) and light fuel oil (LFO) thermal power plants connected to the electricity grid in southern Cameroon. The proposed renewable energy system consists of a solar photovoltaic (PV) field, a pumped hydroelectric energy storage (PHES) system, and an ultra-capacitor energy storage system. The economic and technical performance of the new renewable energy system was assessed using metrics such as total annualized project cost (TAC), loss of load probability (LOLP), and loss of power supply probability (LPSP). The Multi-Objective Bonobo Optimizer (MOBO) was used to both size the components of the new renewable energy system and choose the best location for the solar PV array. The results achieved using MOBO were superior to those obtained from other known optimization techniques. Using metaheuristics for renewable energy system sizing necessitated the creation of mathematical models of renewable energy system components and techno-economic decision criteria under MATLAB software. Based on the results for the deficit rate (LPSP) of zero, the installation of the photovoltaic field in Bafoussam had the lowest TAC of around 52.78 × 106€ when compared to the results for Yaoundé, Bamenda, Douala, and Limbe. Finally, the project profitability analysis determined that the project is financially viable when the energy produced by the renewable energy systems is sold at an average price of 0.12 €/kWh.

Neural networks and particle swarm for transformer oil diagnosis by dissolved gas analysis.

The lifetime of power transformers is closely related to the insulating oil performance. This latter can degrade according to overheating, electric arcs, low or high energy discharges, etc. Such degradation can lead to transformer failures or breakdowns. Early detection of these problems is one of the most important steps to avoid such failures. More efficient diagnostic systems, such as artificial intelligence techniques, are recommended to overcome the limitations of the classical methods. This work deals with diagnosing the power transformer insulating oil by analysis of dissolved gases using new techniques. For this, we have proposed intelligent techniques based on Multilayer artificial neural networks (ANN). Thus, a multi-layer ANN-based model for fault detection is presented. To improve its classification rate, this one was optimized by a meta-heuristic technique as the particle swarm optimization (PSO) technique. Optimized ANNs have never been used in transformer insulating oil diagnostics so far. The robustness and effectiveness of the proposed model is demonstrated, and high accuracy is obtained.

Hybrid genetic algorithm-simulated annealing based electric vehicle charging station placement for optimizing distribution network resilience.

Rapid placement of electric vehicle charging stations (EVCSs) is essential for the transportation industry in response to the growing electric vehicle (EV) fleet. The widespread usage of EVs is an essential strategy for reducing greenhouse gas emissions from traditional vehicles. The focus of this study is the challenge of smoothly integrating Plug-in EV Charging Stations (PEVCS) into distribution networks, especially when distributed photovoltaic (PV) systems are involved. A hybrid Genetic Algorithm and Simulated Annealing method (GA-SAA) are used in the research to strategically find the optimal locations for PEVCS in order to overcome this integration difficulty. This paper investigates PV system situations, presenting the problem as a multicriteria task with two primary objectives: reducing power losses and maintaining acceptable voltage levels. By optimizing the placement of EVCS and balancing their integration with distributed generation, this approach enhances the sustainability and reliability of distribution networks.

An analysis of case studies for advancing photovoltaic power forecasting through multi-scale fusion techniques.

Integration renewable energy sources into current power generation systems necessitates accurate forecasting to optimize and preserve supply-demand restrictions in the electrical grids. Due to the highly random nature of environmental conditions, accurate prediction of PV power has limitations, particularly on long and short periods. Thus, this research provides a new hybrid model for forecasting short PV power based on the fusing of multi-frequency information of different decomposition techniques that will allow a forecaster to provide reliable forecasts. We evaluate and provide insights into the performance of five multi-scale decomposition algorithms combined with a deep convolution neural network (CNN). Additionally, we compare the suggested combination approach's performance to that of existing forecast models. An exhaustive assessment is carried out using three grid-connected PV power plants in Algeria with a total installed capacity of 73.1 MW. The developed fusing strategy displayed an outstanding forecasting performance. The comparative analysis of the proposed combination method with the stand-alone forecast model and other hybridization techniques proves its superiority in terms of forecasting precision, with an RMSE varying in the range of [0.454-1.54] for the three studied PV stations.

Sustainable power management in light electric vehicles with hybrid energy storage and machine learning control.

This paper presents a cutting-edge Sustainable Power Management System for Light Electric Vehicles (LEVs) using a Hybrid Energy Storage Solution (HESS) integrated with Machine Learning (ML)-enhanced control. The system's central feature is its ability to harness renewable energy sources, such as Photovoltaic (PV) panels and supercapacitors, which overcome traditional battery-dependent constraints. The proposed control algorithm orchestrates power sharing among the battery, supercapacitor, and PV sources, optimizing the utilization of available renewable energy and ensuring stringent voltage regulation of the DC bus. Notably, the ML-based control ensures precise torque and speed regulation, resulting in significantly reduced torque ripple and transient response times. In practical terms, the system maintains the DC bus voltage within a mere 2.7% deviation from the nominal value under various operating conditions, a substantial improvement over existing systems. Furthermore, the supercapacitor excels at managing rapid variations in load power, while the battery adjusts smoothly to meet the demands. Simulation results confirm the system's robust performance. The HESS effectively maintains voltage stability, even under the most challenging conditions. Additionally, its torque response is exceptionally robust, with negligible steady-state torque ripple and fast transient response times. The system also handles speed reversal commands efficiently, a vital feature for real-world applications. By showcasing these capabilities, the paper lays the groundwork for a more sustainable and efficient future for LEVs, suggesting pathways for scalable and advanced electric mobility solutions.

New coordinated drive mode switching strategy for distributed drive electric vehicles with energy storage system.

High performance and comfort are key features recommended in hybrid electric vehicle (HEV) design. In this paper, a new coordination strategy is proposed to solve the issue of undesired torque jerks and large power ripples noticed respectively during drive mode commutations and power sources switching. The proposed coordinated switching strategy uses stair-based transition function to perform drive mode commutations and power source switching's within defined transition periods fitting the transient dynamics of power sources and traction machines. The proposed technique is applied on a battery/ supercapacitor electric vehicle whose traction is ensured by two permanent magnet synchronous machines controlled using direct torque control and linked to HEV front and rear wheels. Simulation results highlight that the proposed coordinated switching strategy has a noteworthy positive impact on enhancing HEV transient performance as DC bus fluctuations were reduced to a narrow band of 6 V and transient torque ripples were almost suppressed.

A new intelligently optimized model reference adaptive controller using GA and WOA-based MPPT techniques for photovoltaic systems.

Recently, the integration of renewable energy sources, specifically photovoltaic (PV) systems, into power networks has grown in significance for sustainable energy generation. Researchers have investigated different control algorithms for maximum power point tracking (MPPT) to enhance the efficiency of PV systems. This article presents an innovative method to address the problem of maximum power point tracking in photovoltaic systems amidst swiftly changing weather conditions. MPPT techniques supply maximum power to the load during irradiance fluctuations and ambient temperatures. A novel optimal model reference adaptive controller is developed and designed based on the MIT rule to seek global maximum power without ripples rapidly. The suggested controller is also optimized through two popular meta-heuristic algorithms: The genetic algorithm (GA) and the whale optimization algorithm (WOA). These meta-heuristic approaches have been exploited to overcome the difficulty of selecting the adaptation gain of the MRAC controller. The reference voltage for MPPT is generated in the study through an adaptive neuro-fuzzy inference system. The suggested controller's performance is tested via MATLAB/Simulink software under varying temperature and radiation circumstances. Simulation is carried out using a Soltech 1sth-215-p module coupled to a boost converter, which powers a resistive load. Furthermore, to emphasize the recommended algorithm's performance, a comparative study was done between the optimal MRAC using GA and WOA and the conventional incremental conductance (INC) method.

A multilayer perceptron neural network approach for optimizing solar irradiance forecasting in Central Africa with meteorological insights.

Promoting renewable energy sources, particularly in the solar industry, has the potential to address the energy shortfall in Central Africa. Nevertheless, a difficulty occurs due to the erratic characteristics of solar irradiance data, which is influenced by climatic fluctuations and challenging to regulate. The current investigation focuses on predicting solar irradiance on an inclined surface, taking into consideration the impact of climatic variables such as temperature, wind speed, humidity, and air pressure. The used methodology for this objective is Artificial Neural Network (ANN), and the inquiry is carried out in the metropolitan region of Douala. The data collection device used in this research is the meteorological station located at the IUT of Douala. This station was built as a component of the Douala sustainable city effort, in partnership with the CUD and the IRD. Data was collected at 30-min intervals for a duration of around 2 years, namely from January 17, 2019, to October 30, 2020. The aforementioned data has been saved in a database that underwent pre-processing in Excel and later employed MATLAB for the creation of the artificial neural network model. 80% of the available data was utilized for training the network, 15% was allotted for validation, and the remaining 5% was used for testing. Different combinations of input data were evaluated to ascertain their individual degrees of accuracy. The logistic Sigmoid function, with 50 hidden layer neurons, yielded a correlation coefficient of 98.883% between the observed and estimated sun irradiation. This function is suggested for evaluating the intensities of solar radiation at the place being researched and at other sites that have similar climatic conditions.

Optimizing grid-connected PV systems with novel super-twisting sliding mode controllers for real-time power management.

Over the past years, the use of renewable energy sources (RESs) has grown significantly as a means of providing clean energy to counteract the devastating effects of climate change. Reducing energy costs and pollution have been the primary causes of the rise in solar photovoltaic (PV) system integrations with the grid in recent years. A load that is locally connected to a GCPV requires both active and reactive power control. In order to control both active and reactive power, MAs and advanced controllers are essential. Researchers have used one of the recently developed MAs, known as the CAOA, which is based on mathematical arithmetic operators to tackle a few real-world optimization problems. Some disadvantages of CAOA include its natural tendency to converge to a local optimum and its limited capacity for exploration. By merging the PSO and CAOA methodologies, this article suggests the IAOA. To show how applicable IAOA is, its performance has been evaluated using four benchmark functions. The implementation of an IAOA-based ST-SMC for active and reactive power control is addressed in this article, which offers an innovative approach of research. In comparison to PSO-based ST-SMC and CAOA-based ST-SMC, the proposed IAOA-based ST-SMC appears to be superior, with settling time for active and reactive power control at a minimum of 0.01012 s and 0.5075 s. A real-time OPAL-RT 4510 simulator is used to validate the performance results of a 40 kW GCPV system after it has been investigated in the MATLAB environment.

Extendable high gain low current/high pulse modified quadratic-SEPIC converter for water treatment applications.

Substantial attention has been drawn over the past few years by high step-up dc-dc converters owing to their applications in a wide range. Apart from renewable energy applications, high voltage/ high pulse converters are efficiently used in water treatment applications. The converter suggested a combination of Quadratic and SEPIC converters with a diode-capacitor cell. This topology generates high-voltage repetitive pulses with a single semiconductor switch and reduced component count. The stress across the components is less than the high-gain converters reported in the literature. The topology has an extendable feature by increasing the number of diode-capacitor cells without affecting the stress. The superiority of the high pulse generating topology is validated with a similar converter in the literature. This paper discusses the nL5 simulator results for the proposed rated topology required for water treatment. A scaled-down 50 W prototype is tested for various input voltages to generate high voltage pulse, and the analytical study is validated.