Spark Plasma Sintering of Fine-Grained WC-Co Composites.

Cemented carbides WC-Co are one of the basic tool materials. They constitute over half of the currently used tools intended for machining. The main advantages of WC-Co cemented carbides are high hardness and abrasion resistance. The properties of WC-Co sinters depend mainly on the content of the binding phase, the sintering method and the grain size of the powder from which the sinters were made. The aim of this study was to produce fine-grained WC-Co composites using SPS (spark plasma sintering) technology, as well as examine the effect of the applied technology on the basic properties of WC-Co sinters: microstructure, hardness, phase composition, compaction degree and tribological properties. In the processes carried out, no additives affecting the reduction in grain growth were used. Sintering was conducted at a temperature of 1200 °C with a holding time of 10 min. The process occurred under a load of 100 MPa. Finally, the samples were cooled in a vacuum of 10-6 mbar. We measured the hardness using a Vickers hardness tester. We took hardness measurements along the diameter of the sintered samples. In order to ascertain the fracture toughness (KIC), we measured the radial crack length around the Vickers indentation and applied Shetty's formula. The tribological tests were carried out with a tribotester using the T-01 ball-on-disc method. The obtained data enabled the characterization of the wear process of the tested materials.

Testing for Abrasion Resistance of WC-Co Composites for Blades Used in Wood-Based Material Processing.

Commonly used tool materials for machining wood-based materials are WC-Co carbides. Although they have been known for a long time, there is still much development in the field of sintered tool materials, especially WC-Co carbides and superhard materials. The use of new manufacturing methods (such as FAST-field-assisted sintering technology), which use pulses of electric current for heating, can improve the properties of the materials used for cutting tools, thereby increasing the cost-effectiveness of machining. The ability to increase tool life without the downtime associated with tool wear allows significant cost savings, particularly in mass production. This paper presents the results of a study of the effect of grain size and cobalt content of carbide tool sinters on the tribological properties of the materials studied. The powders used for consolidation were characterised by irregular shape and formed agglomerates of different sizes. Tribological tests were carried out using the T-01 (ball-on-disc) method. In order to determine the wear kinetics, the entire friction path was divided into 15 cycles of 200 m and the weight loss was measured after each stage. In order to determine the mechanism and intensity of wear of the tested materials under technically dry friction conditions, the surface of the tested sinters was observed before the test and after 5, 10, and 15 cycles. The conclusions of the study indicate that the predominant effect of surface cooperation at the friction node is abrasion due to the material chipping that occurs during the process. The results confirm the influence of sintered grain size and cobalt content on durability. In the context of the application of the materials in question for cutting tools, it can be pointed out that sintered WC(0.4)_4 has the highest potential for use in the manufacture of cutting tools.

Application of U-FAST Technology in Sintering of Submicron WC-Co Carbides.

This article presents the microstructure, hardness, fracture toughness coefficient KIC and phase composition of submicron WC-4Co carbides. The carbides were sintered using the innovative U-FAST (Upgraded Field Assisted Sintering Technology) method, from mixtures of WC-Co powders with an average WC grain size of 0.4 µm and 0.8 µm. The obtained sinters were characterized by a relative density above 99% of the theoretical density. The hardness of the obtained composites was above 2000 HV30, while the KIC coefficient was about 8 MPa m1/2.

AFM Measurements and Testing Properties of HDPE and PBT Composites with Fillers in the Form of Montmorillonite and Aluminum Hydroxide.

This paper presents the effect of the addition of fillers such as aluminum hydroxide or montmorillonite on the structure and properties of polymers such as high-density polyethylene (HDPE) and polybutylene terephthalate (PBT). Both types of specimens were obtained by injection molding. X-ray diffraction examinations were performed on the materials obtained to determine the effect of the addition of the fillers used on the degree of crystallinity of the composites. The density and hardness of the composites were evaluated, and the static tensile test and the analysis of the structure parameters using atomic force microscopy (AFM) were also carried out. It was shown that the addition of powder fillers to polymers such as high-density polyethylene and polybutylene terephthalate affects the structure parameters such as surface roughness, mean grain size, anisotropy ratio, fractal dimension, the corner frequency of the composites, and mechanical properties such as Young's pseudo-modulus, average adhesion force, hardness, and tensile strength.

The Analysis of Erosive Wear Resistance of WC-Co Carbides Obtained by Spark Plasma Sintering Method.

WC-Co (tungsten carbide-cobalt) composites are widely used in industry, wear-resistant parts, and cutting tools. As successful tool materials, WC-Co carbides are widely applied in metal cutting, wear applications, chipless forming, stoneworking, wood, and plastic working. These materials are exposed to severe solid particle erosion by sand particles, such as in the wood industry. During the production of furniture with HDF (High Density Fibreboard), MDF (Medium Density Fibreboard), or OSB (Oriented Strand Board), there are observed problems with tool erosion. Contamination, mainly of the HDF by sand, is quite often, which is why all tools used for the machining of such materials are exposed to erosion by sand particles. Although many studies have been performed on the erosion of various metals, and erosion models exist to predict their erosion behavior, the issue is still relevant. The aim of the study was to determine the effect of grain size (submicron, ultrafine) and the manufacturing technology (SPS-Spark Plasma Sintering, conventional) used on the erosive properties of WC-Co sintered carbides. Sinters produced by the SPS method with different sizes of WC grains and commercial samples were used for the tests. Ten two-hour cycles were carried out under medium conditions of quartz sand and quartz sand with 10% SiC added. Used samples were characterised using scanning electron microscopy (SEM) and roughness was determined. Furthermore, erosion studies allowed individuating a wear mechanism as well as the possibility to foresee cutting performance in prospective application.

Properties of WCCo Composites Produced by the SPS Method Intended for Cutting Tools for Machining of Wood-Based Materials.

This paper presents the possibility of using the Spark Plasma Sintering (SPS) method to obtain WCCo composite materials. Such materials are used as cutting blades for machining wood-based materials. Two series of composites, different in grain size and cobalt content, were analyzed in the paper. The produced materials were characterized using Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), and tribological properties were determined. In addition, preliminary tests were carried out on the durability of the blades made of sintered WCCo composites while machining three-layer chipboard. The results of the microstructure analysis proved that the SPS method makes it possible to obtain solid composites. Phase analysis showed the occurrence of the following phases: WC, Co, and Co3W9C4. The lowest friction coefficient value was found in samples sintered using powder with an average primary particle size of 400 nm (ultrafine).