ABSTRACT
ABSTRACT Composite resins are excellent materials for direct restorations in the posterior region, satisfactorily reestablishing esthetics and function. Recently, a new class of composites has been commercialized, the so-called Bulk-fill resins. These resins may be inserted in the dental cavity in increments of 4 to 5 mm thick, and have the advantages of reducing polymerization shrinkage and clinical working time. The aim of this case report was to describe the use of bulk-fill composite resins to restore Class I and Class II cavities by means of two different restorative techniques.
RESUMEN Las resinas compuestas son excelentes materiales para restauraciones directas en la región posterior, restableciendo satisfactoriamente la estética y la función. Recientemente, se ha comercializado una nueva clase de compuestos, las denominadas resinas Bulk Fill. Estas resinas pueden insertarse en la cavidad dental en incrementos de 4 a 5 mm de espesor, y tienen las ventajas de reducir la contracción de la polimerización y el tiempo de trabajo clínico. El objetivo de este informe de caso fue describir el uso de resinas Bulk fill para restaurar las cavidades de Clase I y Clase II mediante dos técnicas de restauración diferentes.
Subject(s)
Humans , Adult , Composite Resins , Dental Restoration, Permanent/methodsABSTRACT
This study sought to measure the microtensile bond strength of a nanofilled composite resin to human dentin after phosphoric acid etching followed by nonvital bleaching. Scanning electron microscopy was used to analyze fracture modes. Twenty extracted sound human maxillary premolars were prepared for Class I defects and assigned randomly to 4 groups (n = 5): Group 1 (control group) samples were unbleached and had no previous acid etching; Group 2 samples were bleached only, Group 3 samples were acid-etched for 15 seconds prior to bleaching, and Group 4 samples were acid-etched for 30 seconds prior to bleaching. There were no statistically significant differences of bond strength values among Groups 1-3; however, the mean values of Group 4 were statistically lower compared with the other groups.
Subject(s)
Acid Etching, Dental/methods , Tooth Bleaching/methods , Bicuspid , Dental Bonding/methods , Dental Bonding/standards , Dental Stress Analysis , Humans , Microscopy, Electron, ScanningABSTRACT
OBJECTIVES: To assess the influence of material/technique selection (direct vs. CAD/CAM inlays) for large MOD composite adhesive restorations and its effect on the crack propensity and in vitro accelerated fatigue resistance. METHODS: A standardized MOD slot-type tooth preparation was applied to 32 extracted maxillary molars (5mm depth and 5mm bucco-palatal width) including immediately sealed dentin for the inlay group. Fifteen teeth were restored with direct composite resin restoration (Miris2) and 17 teeth received milled inlays using Paradigm MZ100 block in the CEREC machine. All inlays were adhesively luted with a light curing composite resin (Filtek Z100). Enamel shrinkage-induced cracks were tracked with photography and transillumination. Cyclic isometric chewing (5 Hz) was simulated, starting with a load of 200 N (5000 cycles), followed by stages of 400, 600, 800, 1000, 1200 and 1400 N at a maximum of 30,000 cycles each. Samples were loaded until fracture or to a maximum of 185,000 cycles. RESULTS: Teeth restored with the direct technique fractured at an average load of 1213 N and two of them withstood all loading cycles (survival=13%); with inlays, the survival rate was 100%. Most failures with Miris2 occurred above the CEJ and were re-restorable (67%), but generated more shrinkage-induced cracks (47% of the specimen vs. 7% for inlays). SIGNIFICANCE: CAD/CAM MZ100 inlays increased the accelerated fatigue resistance and decreased the crack propensity of large MOD restorations when compared to direct restorations. While both restorative techniques yielded excellent fatigue results at physiological masticatory loads, CAD/CAM inlays seem more indicated for high-load patients.