Rapid Isothermal Detection of Pathogenic Clostridioides difficile Using Recombinase Polymerase Amplification.

Nosocomial-associated diarrhea due to Clostridioides difficile infection (CDI) is diagnosed after sample precultivation by the detection of the toxins in enzyme immunoassays or via toxin gene nucleic acid amplification. Rapid and direct diagnosis is important for targeted treatment to prevent severe cases and recurrence. We developed two singleplex and a one-pot duplex fluorescent 15 min isothermal recombinase polymerase amplification (RPA) assays targeting the toxin genes A and B (tcdA and tcdB). Furthermore, we adapted the singleplex RPA to a 3D-printed microreactor device. Analytical sensitivity was determined using a DNA standard and DNA extracts of 20 C. difficile strains with different toxinotypes. Nineteen clostridial and gastrointestinal bacteria strains were used to determine analytical specificity. Adaptation of singleplex assays to duplex assays in a 50 µL volume required optimized primer and probe concentrations. A volume reduction by one-fourth (12.4 µL) was established for the 3D-printed microreactor. Mixing of RPA was confirmed as essential for optimal analytical sensitivity. Detection limits (LOD) ranging from 119 to 1411 DNA molecules detected were similar in the duplex tube format and in the singleplex 3D-printed microreactor format. The duplex RPA allows the simultaneous detection of both toxins important for the timely and reliable diagnosis of CDI. The 3D-printed reaction chamber can be developed into a microfluidic lab-on-a-chip system use at the point of care.

Towards Robust Thermal MEMS: Demonstration of a Novel Approach for Solid Thermal Isolation by Substrate-Level Integrated Porous Microstructures.

Most current thermal MEMS use fragile structures such as thin-film membranes or microcantilevers for thermal isolation. To increase the robustness of these devices, solid thermal insulators that are compatible with MEMS cleanroom processing are needed. This work introduces a novel approach for microscale thermal isolation using porous microstructures created with the recently developed PowderMEMS wafer-level process. MEMS devices consisting of heaters on a thin-film membrane were modified with porous microstructures made from three different materials. A thermal model for the estimation of the resulting thermal conductivity was developed, and measurements for porous structures in ambient air and under vacuum were performed. The PowderMEMS process was successfully used to create microscale thermal insulators in silicon cavities at the wafer level. Measurements indicate thermal conductivities of close to 0.1 W/mK in ambient air and close to 0.04 W/mK for porous structures under vacuum for the best-performing material. The obtained thermal conductivities are lower than those reported for both glass and porous silicon, making PowderMEMS a very interesting alternative for solid microscale thermal isolation.

PowderMEMS-A Generic Microfabrication Technology for Integrated Three-Dimensional Functional Microstructures.

A comprehensive overview of PowderMEMS-a novel back-end-of-line-compatible microfabrication technology-is presented in this paper. The PowderMEMS process solidifies micron-sized particles via atomic layer deposition (ALD) to create three-dimensional microstructures on planar substrates from a wide variety of materials. The process offers numerous degrees of freedom for the design of functional MEMSs, such as a wide choice of different material properties and the precise definition of 3D volumes at the substrate level, with a defined degree of porosity. This work details the characteristics of PowderMEMS materials as well as the maturity of the fabrication technology, while highlighting prospects for future microdevices. Applications of PowderMEMS in the fields of magnetic, thermal, optical, fluidic, and electrochemical MEMSs are described, and future developments and challenges of the technology are discussed.

Suitcase Lab for Rapid Detection of SARS-CoV-2 Based on Recombinase Polymerase Amplification Assay.

In March 2020, the SARS-CoV-2 virus outbreak was declared as a world pandemic by the World Health Organization (WHO). The only measures for controlling the outbreak are testing and isolation of infected cases. Molecular real-time polymerase chain reaction (PCR) assays are very sensitive but require highly equipped laboratories and well-trained personnel. In this study, a rapid point-of-need detection method was developed to detect the RNA-dependent RNA polymerase (RdRP), envelope protein (E), and nucleocapsid protein (N) genes of SARS-CoV-2 based on the reverse transcription recombinase polymerase amplification (RT-RPA) assay. RdRP, E, and N RT-RPA assays required approximately 15 min to amplify 2, 15, and 15 RNA molecules of molecular standard/reaction, respectively. RdRP and E RT-RPA assays detected SARS-CoV-1 and 2 genomic RNA, whereas the N RT-RPA assay identified only SARS-CoV-2 RNA. All established assays did not cross-react with nucleic acids of other respiratory pathogens. The RT-RPA assay's clinical sensitivity and specificity in comparison to real-time RT-PCR (n = 36) were 94 and 100% for RdRP; 65 and 77% for E; and 83 and 94% for the N RT-RPA assay. The assays were deployed to the field, where the RdRP RT-RPA assays confirmed to produce the most accurate results in three different laboratories in Africa (n = 89). The RPA assays were run in a mobile suitcase laboratory to facilitate the deployment at point of need. The assays can contribute to speed up the control measures as well as assist in the detection of COVID-19 cases in low-resource settings.

Schnellnachweis von SARS-CoV-2 mit recombinase polymerase amplification.

The COVID-19 pandemic highlights the need for fast and simple assays for nucleic acid detection. As an isothermal alternative to RT-qPCR, we outline the development of a detection scheme for SARS-CoV-2 RNA based on reverse transcription recombinase polymerase amplification (RT-RPA) technology. RPA uses recombination proteins in combination with a DNA polymerase for rapid amplification of target DNA at a constant temperature (39-42 °C) within 10 to 20 minutes and can be monitored in real-time with fluorescent probes.

3D Printed Monolithic Microreactors for Real-Time Detection of Klebsiella pneumoniae and the Resistance Gene blaNDM-1 by Recombinase Polymerase Amplification.

We investigate the compatibility of three 3D printing materials towards real-time recombinase polymerase amplification (rtRPA). Both the general ability of the rtRPA reaction to occur while in contact with the cured 3D printing materials as well as the residual autofluorescence and fluorescence drift in dependence on post curing of the materials is characterized. We 3D printed monolithic rtRPA microreactors and subjected the devices to different post curing protocols. Residual autofluorescence and drift, as well as rtRPA kinetics, were then measured in a custom-made mobile temperature-controlled fluorescence reader (mTFR). Furthermore, we investigated the effects of storage on the devices over a 30-day period. Finally, we present the single- and duplex rtRPA detection of both the organism-specific Klebsiella haemolysin (khe) gene and the New Delhi metallo-ß-lactamase 1 (blaNDM-1) gene from Klebsiella pneumoniae. Results: No combination of 3D printing resin and post curing protocol completely inhibited the rtRPA reaction. The autofluorescence and fluorescence drift measured were found to be highly dependent on printing material and wavelength. Storage had the effect of decreasing the autofluorescence of the investigated materials. Both khe and blaNDM-1 were successfully detected by single- and duplex-rtRPA inside monolithic rtRPA microreactors printed from NextDent Ortho Clear (NXOC). The reaction kinetics were found to be close to those observed for rtRPA performed in a microcentrifuge tube without the need for mixing during amplification. Singleplex assays for both khe and blaNDM-1 achieved a limit of detection of 2.5 × 101 DNA copies while the duplex assay achieved 2.5 × 101 DNA copies for khe and 2.5 × 102 DNA copies for blaNDM-1. Impact: We expand on the state of the art by demonstrating a technology that can manufacture monolithic microfluidic devices that are readily suitable for rtRPA. The devices exhibit very low autofluorescence and fluorescence drift and are compatible with RPA chemistry without the need for any surface pre-treatment such as blocking with, e.g., BSA or PEG.

Rapid Detection of SARS-CoV-2 by Low Volume Real-Time Single Tube Reverse Transcription Recombinase Polymerase Amplification Using an Exo Probe with an Internally Linked Quencher (Exo-IQ).

BACKGROUND: The current outbreak of SARS-CoV-2 has spread to almost every country with more than 5 million confirmed cases and over 300,000 deaths as of May 26, 2020. Rapid first-line testing protocols are needed for outbreak control and surveillance. METHODS: We used computational and manual designs to generate a suitable set of reverse transcription recombinase polymerase amplification (RT-RPA) primer and exonuclease probe, internally quenched (exo-IQ), sequences targeting the SARS-CoV-2 N gene. RT-RPA sensitivity was determined by amplification of in vitro transcribed RNA standards. Assay selectivity was demonstrated with a selectivity panel of 32 nucleic acid samples derived from common respiratory viruses. To validate the assay against full-length SARS-CoV-2 RNA, total viral RNA derived from cell culture supernatant and 19 nasopharyngeal swab samples (8 positive and 11 negative for SARS-CoV-2) were screened. All results were compared to established RT-qPCR assays. RESULTS: The 95% detection probability of the RT-RPA assay was determined to be 7.74 (95% CI: 2.87-27.39) RNA copies per reaction. The assay showed no cross-reactivity to any other screened coronaviruses or respiratory viruses of clinical significance. The developed RT-RPA assay produced 100% diagnostic sensitivity and specificity when compared to RT-qPCR (n = 20). CONCLUSIONS: With a run time of 15 to 20 minutes and first results being available in under 7 minutes for high RNA concentrations, the reported assay constitutes one of the fastest nucleic acid based detection methods for SARS-CoV-2 to date and may provide a simple-to-use alternative to RT-qPCR for first-line screening at the point of need.

A lab-on-a-chip for free-flow electrophoretic preconcentration of viruses and gel electrophoretic DNA extraction.

Nucleic acid amplification techniques such as real-time PCR are essential instruments for the identification and quantification of viruses. They are fast, very sensitive and highly specific, but often require elaborate and labor intensive sample preparation to achieve successful amplification of the target sequence. In this work we demonstrate the complete microfluidic preparation of amplifiable virus DNA from dilute specimens. Our approach combines free-flow electrophoretic preconcentration of viral particles with thermal lysis and gel-electrophoretic nucleic acid extraction on a single device. The on-chip preconcentration achieves a capture efficiency of >99% for dilute suspensions of bacteriophage PhiX174. Following preconcentration, phages are thermally lysed and released DNA is recovered after 40 s of on-chip gel-electrophoresis with a recovery rate of ∼73%. Furthermore we demonstrate a detection limit of ∼1 PFU ml-1 (∼0.02 DNA copies per µl) for the detection of bacteriophage PhiX174 by PCR. To simplify operation of the device, we describe the development of a custom-made chip holder as well as a compact peristaltic pump and power supply, which enable user-friendly operation with low risk of cross-contamination and high potential for automation in the field of point-of-care diagnostics.

A lab-on-a-chip for rapid miRNA extraction.

We present a simple to operate microfluidic chip system that allows for the extraction of miRNAs from cells with minimal hands-on time. The chip integrates thermoelectric lysis (TEL) of cells with native gel-electrophoretic elution (GEE) of released nucleic acids and uses non-toxic reagents while requiring a sample volume of only 5 µl. These properties as well as the fast process duration of 180 seconds make the system an ideal candidate to be part of fully integrated point-of-care applications for e.g. the diagnosis of cancerous tissue. GEE was characterized in comparison to state-of-the-art silica column (SC) based RNA recovery using the mirVana kit (Ambion) as a reference. A synthetic miRNA (miR16) as well as a synthetic snoRNA (SNORD48) were subjected to both GEE and SC. Subsequent detection by stem-loop RT-qPCR demonstrated a higher yield for miRNA recovery by GEE. SnoRNA recovery performance was found to be equal for GEE and SC, indicating yield dependence on RNA length. Coupled operation of the chip (TEL + GEE) was characterized using serial dilutions of 5 to 500 MCF7 cancer cells in suspension. Samples were split and cells were subjected to either on-chip extraction or SC. Eluted miRNAs were then detected by stem-loop RT-qPCR without any further pre-processing. The extraction yield from cells was found to be up to ~200-fold higher for the chip system under non-denaturing conditions. The ratio of eluted miRNAs is shown to be dependent on the degree of complexation with miRNA associated proteins by comparing miRNAs purified by GEE from heat-shock and proteinase-K based lysis.

Direct DNA and RNA detection from large volumes of whole human blood.

PCR inhibitors in clinical specimens negatively affect the sensitivity of diagnostic PCR and RT-PCR or may even cause false-negative results. To overcome PCR inhibition, increase the sensitivity of the assays and simplify the detection protocols, simple methods based on quantitative nested real-time PCR and RT-PCR were developed to detect exogenous DNA and RNA directly from large volumes of whole human blood (WHB). Thermus thermophilus (Tth) polymerase is resistant to several common PCR inhibitors and exhibits reverse transcriptase activity in the presence of manganese ions. In combination with optimized concentrations of magnesium ions and manganese ions, Tth polymerase enabled efficient detection of DNA and RNA from large volumes of WHB treated with various anticoagulants. The applicability of these methods was further demonstrated by examining WHB specimens collected from different healthy individuals and those stored under a variety of conditions. The detection limit of these methods was determined by detecting exogenous DNA, RNA, and bacteria spiked in WHB. To the best of our knowledge, direct RNA detection from large volumes of WHB has not been reported. The results of the developed methods can be obtained within 4 hours, making them possible for rapid and accurate detection of disease-causing agents from WHB.

Capacity of rTth polymerase to detect RNA in the presence of various inhibitors.

The full potential of the real-time reverse transcription polymerase chain reaction (RT-PCR) as a rapid and accurate diagnostic method is limited by DNA polymerase inhibitors as well as reverse transcriptase inhibitors which are ubiquitous in clinical samples. rTth polymerase has proven to be more resistant to DNA polymerase inhibitors present in clinical samples for DNA detection and also exhibits reverse transcriptase activity in the presence of Mn2+ ions. However, the capacity of rTth polymerase, which acts as DNA polymerase and reverse transcriptase, to detect RNA in the presence of various inhibitors has not been investigated in detail. Herein, the inhibitors originating from various clinical samples such as blood, urine, feces, bodily fluids, tissues and reagents used during nucleic acid extraction were employed to evaluate the capacity of rTth polymerase to detect RNA. The results show that the inhibitors have different inhibitory effects on the real-time RT-PCR reactions by rTth polymerase, and the inhibitory effects are concentration dependent. Additionally, the capacity of rTth polymerase to detect RNA in the presence of various inhibitors is better or at least comparable with its capacity to detect DNA in the presence of various inhibitors. As a consequence, RNA may be directly detected in the presence of co-purified inhibitors or even directly from crude clinical samples by rTth polymerase.