Silicon / Perovskite Tandem Solar Cells with Reverse Bias Stability down to -40 V. Unveiling the Role of Electrical and Optical Design.

The reverse bias stability is a key concern for the commercialization and reliability of halide perovskite photovoltaics. Here, the robustness of perovskite-silicon tandem solar cells to reverse bias electrical degradation down to -40 V is investigated. The two-terminal tandem configuration, with the perovskite coupled to silicon, can improve the solar cell resistance to severe negative voltages when the tandem device is properly designed. While perovskite cells typically exhibit early reverse bias breakdown voltages, the serial connection with silicon cells with large shunt resistances and high voltage breakdown limits their negative polarization and prevent the passage of large current densities when reverse biased. The importance of careful optical design is illustrated, with bottom-limited conditions required to prevent the perovskite top cell from exploring its own breakdown. This aspect is of great importance in the case of partial shading events when the solar spectrum is richer in the IR components than the standard AM1.5G. Notably, 100% of efficiency retained after polarization at -40 V in different stressing conditions is observed. The results presented suggest that standard industrial bypass diode schemes may be compatible with silicon/perovskite tandem photovoltaics and provide new guidelines for the standardization of the stressing protocols.

Directly-Fused Ni(II)Porphyrin Conjugated Polymers with Blocked meso-Positions: Impact on Electrocatalytic Properties.

The oxidative coupling reaction of two Ni(II) porphyrins meso-substituted with three and four phenyl groups, Ni(II) 5,10,15-(triphenyl)porphyrin (NiPh3P) and Ni(II) 5,10,15,20-(tetraphenyl)porphyrin (NiPh4P) respectively, was investigated in a oxidative chemical vapor deposition (oCVD) process. Irrespective of the number of meso-substituents, high-resolution mass spectrometry evidences the formation of oligomeric species containing up to five porphyrin units. UV-Vis-NIR and XPS analyses of the oCVD films highlighted a strong dependence of the intermolecular coupling reaction with the substrate temperature. Specifically, higher substrate temperatures yield lowering of valence band maxima and reduction of the band gap. The formation of conjugated polymeric assemblies results in increased conductivities as compared to their sublimed counterparts. Yet, electrocatalytic measurements exhibit water oxidation onset overpotentials (308 mV for pNiPh3P and 343 mV for pNiPh4P) comparatively higher than the onset overpotential measured for the oCVD film from Ni(II) 5,15-(diphenyl)porphyrin (pNiPh2P), i. e. 283 mV. Although DFT and comparative oCVD studies suggest the formation of directly fused porphyrins involving 'phenyl-mediated' and ß-ß linkages when reacting tetra-meso-substituted porphyrins, the present findings highlight that multiple direct fusion (ß-ß/meso-meso/ß-ß or meso-ß/ß-meso) is essential for Ni(II) porphyrin-based conjugated polymers to enable a dinuclear radical oxo-coupling operating mechanism for water oxidation at low overpotential and durable catalytic activity.

Highly stable CsPbBr3 perovskite phases from new lead ß-diketonate glyme adducts.

Lead is one of the key metals of the all-inorganic lead halide perovskites. This work tailors novel architectures of lead's coordination sphere using a ß-diketone (H-hfa = 1,1,1,5,5,5-hexafluoro-2,4-pentanedione) and a glyme (monoglyme, diglyme, triglyme, or tetraglyme) ligand. The coordination chemistry and thermal behaviour of these "Pb(hfa)2·glyme" adducts have been analysed through FT-IR spectroscopy, 1H and 13C NMR analyses, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). Single-crystal X-ray diffraction studies provide evidence of the formation of a monomeric Pb(hfa)2·monoglyme structure. In order to validate the potentiality of these "Pb(hfa)2·glyme" precursors for the fabrication of Pb-based halide perovskites, a facile, one-step and low-temperature solution approach has been applied to prepare CsPbBr3 microcrystals with a process carried out in air under atmospheric pressure. Pure stoichiometric CsPbBr3 powders, obtained using Cs(hfa) and Br2 as cesium and bromide sources, respectively, show excellent stability under atmospheric conditions. Better results are obtained in terms of yield and stability from the diglyme and tetraglyme lead adducts. Field emission scanning electron microscopy (FE-SEM) indicates a good uniform morphology of cubic grains, while the structure and the 1 : 1 : 3 stoichiometry of Cs : Pb : Br are confirmed by X-ray diffraction (XRD) and energy dispersive X-ray analysis (EDX), respectively. Tauc plots derived from absorption spectroscopy point to optical energy band-gaps (Eg) in the 2.21-2.27 eV range, in agreement with literature data. The present research elucidates the potential of these novel "Pb(hfa)2·glyme" adducts as promising lead precursors for CsPbBr3 perovskite synthesis, paving the way for their implementation in various technological applications.

Fused Metalloporphyrin Thin Film with Tunable Porosity via Chemical Vapor Deposition.

Porous and highly conjugated multiply fused porphyrin thin films are prepared from a fast and single-step chemical vapor deposition approach. While the solution-based coupling of porphyrins is usually undertaken at room temperature, the gas phase reaction of nickel(II) 5,15-(diphenyl)porphyrin and iron(III) chloride (FeCl3) is investigated for temperatures as high as 200 °C. Helium ion and atomic force microscopy, supported by weight and thickness measurements, shows a drastic decrease of the fused porphyrin thin film's density accompanied by the formation of a mesoporous morphology upon increase of the reaction temperature. The increase of the film's porosity is attributed to formation of a greater amount of HCl (originated from both the oxidative coupling and chlorination reactions) and the release of gaseous FeCl3 byproducts, i.e., Cl2, at higher deposition temperatures. In addition, high resolution mass spectrometry reveals that increase of the reaction temperature promotes a higher degree of conjugation of the fused porphyrins chains, which ensures that high electronic conductivities are maintained along with high porosity. The method reported herein could enable the engineering of fused porphyrin thin films in sensing and catalytic devices.

Molecular flattening effect to enhance the conductivity of fused porphyrin tape thin films.

The straightforward synthesis of directly fused porphyrins (porphyrin tapes) from 5,15-diphenyl porphyrinato nickel(ii) complexes with different substituents on the phenyl rings is achieved while processing from the gas phase. The porphyrin tapes, exhibiting NIR absorption, are readily obtained in thin film form. The gas phase approach cuts the need for solubilizing groups allowing for the first time the study of their conductivity according to the substituent. 2-Point probe and conductivity AFM measurements evidence that reducing the size of the meso substituents, phenyl < mesityl < di(3,5-tert-butyl)phenyl < di(2,6-dodecyloxy)phenyl, improves the thin film conductivity by several orders of magnitude. Density functional theory and gel permeation chromatography, correlate this improvement to changes in the intermolecular distances and molecular geometry. Furthermore, the oCVD of porphyrins with free ortho-phenyl positions causes intramolecular dehydrogenative side reactions inducing a complete planarization of the molecule. This molecular flattening drastically affects the π-π stacking between the porphyrins further enhancing the electronic properties of the films.

Reactivity of Nickel(II) Porphyrins in oCVD Processes-Polymerisation, Intramolecular Cyclisation and Chlorination.

Oxidative chemical vapour deposition of (5,15-diphenylporphyrinato)nickel(II) (NiDPP) with iron(III) chloride as oxidant yielded a conjugated poly(metalloporphyrin) as a highly coloured thin film, which is potentially useful for optoelectronic applications. This study clarified the reactive sites of the porphyrin monomer NiDPP by HRMS, UV/Vis/NIR spectroscopy, cyclic voltammetry and EPR spectroscopy in combination with quantum chemical calculations. Unsubstituted meso positions are essential for successful polymerisation, as demonstrated by varying the porphyrin meso substituent pattern from di- to tri- and tetraphenyl substitution. DFT calculations support the proposed radical oxidative coupling mechanism and explain the regioselectivity of the C-C coupling processes. Depositing the conjugated polymer on glass slides and on thermoplastic transparent polyethylene naphthalate demonstrated the suitability of the porphyrin material for flexible optoelectronic devices.

Conductive Fused Porphyrin Tapes on Sensitive Substrates by a Chemical Vapor Deposition Approach.

Oxidative polymerization of nickel(II) 5,15-diphenyl porphyrin and nickel(II) 5,15-bis(di-3,5-tert-butylphenyl) porphyrin by oxidative chemical vapor deposition (oCVD) yields multiply fused porphyrin oligomers in thin film form. The oCVD technique enables one-step formation, deposition, and p-doping of conjugated poly(porphyrins) coatings without solvents or post-treatments. The decisive reactions and side reactions during the oCVD process are shown by high-resolution mass spectrometry. Owing to the highly conjugated structure of the fused tapes, the thin films exhibit an electrical conductivity of 3.6×10-2  S cm-1 and strong absorption in the visible to near-infrared spectral region. The formation of smooth conjugated poly(porphyrins) coatings, even on sensitive substrates, is demonstrated by deposition and patterning on glass, silicon, and paper. Formation of conductive poly(porphyrins) thin films could enable the design of new optoelectronic devices using the oCVD approach.