Boric acid and Molybdenum trioxide synergistically stimulate osteogenic differentiation of human bone marrow-derived mesenchymal stromal cells.

INTRODUCTION: Metals and their metal ions have been shown to exhibit certain biological functions that make them attractive for use in biomaterials, for example in bone tissue engineering (BTE) applications. Recent data shows that Molybdenum (Mo) is a potent inducer of osteogenic differentiation in human bone marrow-derived mesenchymal stromal cells (BMSCs). On the other hand, while boron (B) has been shown to enhance vascularization in BTE applications, its impact on osteogenic differentiation is volatile: while improved osteogenic differentiation has been described, other data show that B might slow down osteogenic differentiation or reduce the calcification of the extracellular matrix (ECM) when applied in higher doses. Still, the combination of pro-osteogenic Mo and pro-angiogenic B is certainly attractive in the context of biomaterials intended for the use in BTE. METHODS: Therefore, the combined effect of molybdenum trioxide and boric acid at different ratios was investigated in this study to evaluate the effects on the viability, proliferation, osteogenic differentiation, ECM production and maturation of BMSCs. RESULTS: Mo ions proved to be stronger osteoinductive compared to B, in fact, while some osteogenic differentiation markers were downregulated in the presence of B, the presence of Mo provided compensation. The combined application of B and Mo indicated a combination of individual effects, partially even enhancing the expected combined performance of the single stimulations. CONCLUSIONS: The combination of B and Mo might be beneficial for BTE applications since the limited osteogenic properties of B can be compensated by Mo. Furthermore, since B is known to be pro-angiogenic, the combination of both substances may synergistically lead to improved vascularization and bone regeneration. Future studies should assess the angiogenic performance of this combination in greater detail.

Time-dependent hyper-viscoelastic parameter identification of human articular cartilage and substitute materials.

Numerical simulations are a valuable tool to understand which processes during mechanical stimulations of hydrogels for cartilage replacement influence the behavior of chondrocytes and contribute to the success or failure of these materials as implants. Such simulations critically rely on the correct prediction of the material response through appropriate material models and corresponding parameters. In this study, we identify hyper-viscoelastic material parameters for numerical simulations in COMSOL Multiphysics® v. 5.6 for human articular cartilage and two replacement materials, the commercially available ChondroFillerliquid and oxidized alginate gelatin (ADA-GEL) hydrogels. We incorporate the realistic experimental boundary conditions into an inverse parameter identification scheme based on data from multiple loading modes simultaneously, including cyclic compression-tension and stress relaxation experiments. We provide individual parameter sets for the unconditioned and conditioned responses and discuss how viscoelastic effects are related to the materials' microstructure. ADA-GEL and ChondroFillerliquid exhibit faster stress relaxation than cartilage with lower relaxation time constants, while cartilage has the largest viscoelastic stress contribution. The elastic response predominates in ADA-GEL and ChondroFillerliquid, while the viscoelastic response predominates in cartilage. These results will help to simulate mechanical stimulations, support the development of suitable materials with distinct mechanical properties in the future and provide parameters and insight into the time-dependent material behavior of human articular cartilage.

Hyperelastic parameter identification of human articular cartilage and substitute materials.

Numerical simulations are a valuable tool in the field of tissue engineering for cartilage repair and can help to understand which mechanical properties affect the behavior of chondrocytes and contribute to the success or failure of surrogate materials as implants. However, special attention needs to be paid when identifying corresponding material parameters in order to provide reliable numerical predictions of the material's response. In this study, we identify hyperelastic material parameters for numerical simulations in COMSOL Multiphysics® v. 5.6 for human articular cartilage and two surrogate materials, commercially available ChondroFillerliquid, and oxidized alginate-gelatin (ADA-GEL) hydrogels. We consider several hyperelastic isotropic material models and provide separate parameter sets for the unconditioned and the conditioned material response, respectively, based on previously generated experimental data including both compression and tension experiments. We compare a direct parameter identification approach assuming homogeneous deformation throughout the specimen and an inverse approach, where the experiments are simulated using a finite element model with realistic boundary conditions in COMSOL Multiphysics® v. 5.6. We demonstrate that it is important to consider both compression and tension data simultaneously and to use the inverse approach to obtain reliable parameters. The one-term Ogden model best represents the unconditioned response of cartilage, while the conditioned response of cartilage and ADA-GEL is equally well represented by the two-term Ogden and five-term Mooney-Rivlin models. The five-term Mooney-Rivlin model is also most suitable to model the unconditioned response of ADA-GEL. For ChondroFillerliquid, we suggest using the five-term Mooney-Rivlin or two-term Ogden model for the unconditioned and the two-term Ogden model for the conditioned material response. These results will help to choose appropriate material models and parameters for simulations of whole joints or to advance mechanical-stimulation assisted cartilage tissue engineering in the future.

Anti-inflammatory and antibacterial activities of cerium-containing mesoporous bioactive glass nanoparticles for drug-free biomedical applications.

Mesoporous bioactive glass nanoparticles (MBGNPs) are attracting significant attention as suitable materials for multifunctional biomedical applications. In this study, cerium was incorporated into MBGNPs using two different approaches. In the first approach, cerium was added to the glass system directly during the synthesis, while in the second approach, cerium was added to the as-synthesized MBGNPs via the template ion-exchange method. The influence of the method of synthesis on the physicochemical properties of nanoparticles was examined by SEM, TEM, XRD, FTIR, and N2 adsorption-desorption analyses. The MBGNPs exhibited spheroidal morphology and disordered mesoporous structure. XRD analysis confirmed the amorphous nature of the nanoparticles. The chemical composition was determined by the acid digestion method using ICP-OES. The influence of the synthesis method on the specific surface area, mesoporosity, and solubility of synthesized nanoparticles in Tris/HCl (pH 7.4) and acetate (pH 4.5) buffer has also been studied. The obtained Ce containing MBGNPs were non-cytotoxic toward â€‹preosteoblast MC3T3-E1 cells in contact with nanoparticles in a concentration of up to 100 â€‹µg/mL. The anti-inflammatory effect of Ce containing MBGNPs was tested with lipopolysaccharides (LPS)-induced proinflammatory RAW 264.7 macrophage cells. Ce containing MBGNPs decreased the release of nitric oxide, indicating the anti-inflammatory response of macrophage cells. Ce containing MBGNPs also showed antibacterial activity against S. aureus and E. coli. The mentioned features of the obtained MBGNPs make them useful in a variety of biomedical applications, considering their biocompatibility, anti-inflammatory response, and enhanced antibacterial effect.

A bilayered tissue engineered in vitro model simulating the tooth periodontium.

Due to the complexity of the structure of the tooth periodontium, regeneration of the full tooth attachment is not a trivial task. There is also a gap in models that can represent human tooth attachment in vitro and in vivo. The aim of this study was to develop a bilayered in vitro construct that simulated the tooth periodontal ligament and attached alveolar bone, for the purpose of tissue regeneration and investigation of physiological and orthodontic loading. Two types of materials were used to develop this construct: sol-gel 60S10Mg derived scaffold, representing the hard tissue component of the periodontium, and commercially available Geistlich Bio-Gide® collagen membrane, representing the soft tissue component of the tooth attachment. Each scaffold was dynamically seeded with human periodontal ligament cells (HPDLCs). Scaffolds were either cultured separately, or combined in a bilayered construct, for 2 weeks. Characterisation of the individual scaffolds and the bilayered constructs included biological characterisation (cell viability, scanning electron microscopy to confirm cell attachment, gene expression of periodontium regeneration markers), and mechanical characterisation of scaffolds and constructs. HPDLCs enjoyed a biocompatible 3-dimensional environment within the bilayered construct components. There was no drop in cellular gene expression in the bilayered construct, compared to the separate scaffolds.

Mechanical properties of cell- and microgel bead-laden oxidized alginate-gelatin hydrogels.

3D-printing technologies, such as biofabrication, capitalize on the homogeneous distribution and growth of cells inside biomaterial hydrogels, ultimately aiming to allow for cell differentiation, matrix remodeling, and functional tissue analogues. However, commonly, only the mechanical properties of the bioinks or matrix materials are assessed, while the detailed influence of cells on the resulting mechanical properties of hydrogels remains insufficiently understood. Here, we investigate the properties of hydrogels containing cells and spherical PAAm microgel beads through multi-modal complex mechanical analyses in the small- and large-strain regimes. We evaluate the individual contributions of different filler concentrations and a non-fibrous oxidized alginate-gelatin hydrogel matrix on the overall mechanical behavior in compression, tension, and shear. Through material modeling, we quantify parameters that describe the highly nonlinear mechanical response of soft composite materials. Our results show that the stiffness significantly drops for cell- and bead concentrations exceeding four million per milliliter hydrogel. In addition, hydrogels with high cell concentrations (≥6 mio ml-1) show more pronounced material nonlinearity for larger strains and faster stress relaxation. Our findings highlight cell concentration as a crucial parameter influencing the final hydrogel mechanics, with implications for microgel bead drug carrier-laden hydrogels, biofabrication, and tissue engineering.

Ionic dissolution products of Cerium-doped bioactive glass nanoparticles promote cellular osteogenic differentiation and extracellular matrix formation of human bone marrow derived mesenchymal stromal cells.

Cerium (Ce) is a promising candidate ion for application in bone tissue engineering (BTE) since it reduces the presence of reactive oxygen species. Ce-doped mesoporous bioactive glass nanoparticles (MBGNs) serving as vectors for the local application of Ce already demonstrated stimulating effects on the expression of pro-osteogenic genes in Saos-2 cells. So far, there is no evidence available about the effects of Ce-doped MBGNs on the viability, osteogenic differentiation and the formation of the osseous extracellular matrix (ECM) of primary human bone marrow-derived mesenchymal stromal cells (BMSCs). Therefore, in this study, the biocompatibility of the ionic dissolution products (IDPs) of MBGNs containing increasing concentrations of CeO2(0.05 MCe-MBGNs, composition in mol%: 86.6SiO2-12.1CaO-1.3CeO2; and 0.2 MCe-MBGNs, composition in mol%: 86.0SiO2-11.8CaO-2.2CeO2) and unmodified MBGNs (composition in mol%: 86SiO2-14CaO) was evaluated using human BMSCs. Eventually, the impact of the MBGNs' IDPs on the cellular osteogenic differentiation and their ability to build and mature a primitive osseous ECM was assessed. The Ce-doped MBGNs had a positive influence on the viability and stimulated the cellular osteogenic differentiation of human BMSCs evaluated by analyzing the activity of alkaline phosphate as a marker enzyme for osteoblasts in the present setting. Furthermore, the formation and calcification of a primitive osseous ECM was significantly stimulated in the presence of Ce-doped MBGNs in a positive concentration-dependent manner as demonstrated by an elevated presence of collagen and increased ECM calcification. The results of thisin-vitrostudy show that Ce-doped MBGNs are attractive candidates for further application in BTE.

Complex mechanical behavior of human articular cartilage and hydrogels for cartilage repair.

The mechanical behavior of cartilage tissue plays a crucial role in physiological mechanotransduction processes of chondrocytes and pathological changes like osteoarthritis. Therefore, intensive research activities focus on the identification of implant substitute materials that mechanically mimic the cartilage extracellular matrix. This, however, requires a thorough understanding of the complex mechanical behavior of both native cartilage and potential substitute materials to treat cartilage lesions. Here, we perform complex multi-modal mechanical analyses of human articular cartilage and two surrogate materials, commercially available ChondroFillerliquid, and oxidized alginate-gelatin (ADA-GEL) hydrogels. We show that all materials exhibit nonlinearity and compression-tension asymmetry. However, while hyaline cartilage yields higher stresses in tension than in compression, ChondroFillerliquid and ADA-GEL exhibit the opposite trend. These characteristics can be attributed to the materials' underlying microstructure: Both cartilage and ChondroFillerliquid contain fibrillar components, but the latter constitutes a bi-phasic structure, where the 60% nonfibrillar hydrogel proportion dominates the mechanical response. Of all materials, ChondroFillerliquid shows the most pronounced viscous effects. The present study provides important insights into the microstructure-property relationship of cartilage substitute materials, with vital implications for mechanically-driven material design in cartilage engineering. In addition, we provide a data set to create mechanical simulation models in the future.

Alginate-based hydrogels show the same complex mechanical behavior as brain tissue.

Mimicking the mechanical properties of native human tissues is one key route in tissue engineering. However, the successful creation of functional tissue equivalents requires the comprehensive understanding of the complex and nonlinear mechanical properties of both native tissues and biomaterials. Here, we demonstrate that it is possible to replicate the complex mechanical behavior of soft tissues, exemplary shown for porcine brain tissue, under multiple loading conditions, compression, tension, and torsional shear, through simple blends of alginate and gelatin hydrogels. Alginate exhibits a pronounced compression-tension asymmetry and a nonlinear behavior, while gelatin shows an almost linear response. Blended together, alginate-gelatin (ALG-GEL) hydrogels can resemble the characteristic nonlinear, conditioning, and compression-tension-asymmetric behavior of brain tissue. We demonstrate that hydrogel concentration and incubation effectively tune the stiffness and loading-mode-specific stress relaxation behavior. The stiffness increases with increasing hydrogel concentration and decreases with increasing incubation time. In addition, we observe slower stress relaxation after long incubation times. Our systematic approach highlights the importance of single component, multi-modal mechanical analysis of hydrogels to understand the distinct structure-mechanics relation of each hydrogel component to eventually mimic the response of native tissues. The presented dataset will allow for the structurally derived compositional design of hydrogels for a broad variety of tissue engineering applications.

Cell adhesion evaluation of laser-sintered HAp and 45S5 bioactive glass coatings on micro-textured zirconia surfaces using MC3T3-E1 osteoblast-like cells.

Laser texturing is a technique that has been increasingly explored for the surface modification of several materials on different applications. Laser texturing can be combined with conventional coating techniques to functionalize surfaces with bioactive properties, stimulating cell differentiation and adhesion. This study focuses on the cell adhesion of laser-sintered coatings of hydroxyapatite (HAp) and 45S5 bioactive glass (45S5 BG) on zirconia textured surfaces using MC3T3-E1 cells. For this purpose, zirconia surfaces were micro-textured via laser and then coated with HAp and 45S5 BG glass via dip coating. Afterwards, the bioactive coatings were laser sintered, and a reference group of samples was conventionally sintering. The cell adhesion characterisation was achieved by cell viability performing live/dead analysis using fluorescence stains and by SEM observations for a qualitative analysis of cell adhesion. The in vitro results showed that a squared textured pattern with 100µm width grooves functionalized with a bioactive coating presented an increase of 90% of cell viability compared to flat surfaces after 48h of incubation. The functionalized laser sintered coatings do not present significant differences in cell viability when compared to conventionally sintered coatings. Therefore, the results reveal that laser sintering of HAp and 45S5 BG coatings is a fast and attractive coating technique.

Favorable angiogenic properties of the borosilicate bioactive glass 0106-B1 result in enhanced in vivo osteoid formation compared to 45S5 Bioglass.

The 45S5-bioactive glass (BG) composition is the most commonly investigated amongst BG-based bone substitutes. By changing BG compositions and by addition of therapeutically active ions such as boron, the biological features of BGs can be tailored towards specific needs and possible drawbacks can be overcome. The borosilicate glass 0106-B1 (composition in wt%: 37.5 SiO2, 22.6 CaO, 5.9 Na2O, 4.0 P2O5, 12.0 K2O, 5.5 MgO, 12.5 B2O3) has demonstrated pro-angiogenic properties. However, the osteogenic performance of the 0106-B1-BG and its influence on cell viability and proliferation in vitro as well as its osteogenic and angiogenic properties in vivo have not been investigated. Therefore, in this study, the impact of 0106-B1-BG and 45S5-BG on osteogenic differentiation, viability and proliferation on human mesenchymal stromal cells (MSCs) was assessed in vitro. Furthermore, MSC-seeded scaffolds made from both BG types were implanted subcutaneously in immunodeficient mice for 10 weeks. Osteoid formation was quantified by histomorphometry, vascularization was visualized by immunohistological staining. Additionally, the in vivo expression patterns of genes correlating with osteogenesis and angiogenesis were analyzed. In vitro, the impact of 45S5-BG and 0106-B1-BG on the proliferation, viability and osteogenic differentiation of MSCs was comparable. In vivo, scaffolds made from 0106-B1-BG significantly outperformed the 45S5-BG-based scaffolds regarding the amount and maturation of the osteoid. Furthermore, 0106-B1-BG-based scaffolds showed significantly increased angiogenic gene expression patterns. In conclusion, the beneficial angiogenic properties of 0106-B1-BG result in improved osteogenic properties in vivo, making the 0106-B1-BG a promising candidate for further investigation, e.g. in a bone defect model.

Development of biocompatible and fully bioabsorbable PLA/Mg films for tissue regeneration applications.

During recent years, Mg reinforced polylactic acid (PLA) composites have emerged as potential biocompatible and bioabsorbable materials for biomedical applications. It has been shown that Mg particles added to a matrix based on a biodegradable polymer can address the lack of bioactivity and the low mechanical properties of the polymers and, furthermore, it can counteract the detrimental effects associated to the high degradation rate of Mg, as alkalinization and elevated H2 release. Additionally, the polymer can protect the Mg particles, by tailoring their degradation rate. Former processing of these composites performed by extrusion, compression and injection molding employed Mg contents up to 10 wt%. Higher amounts of Mg resulted in heterogeneous materials and thermally degraded matrices, with the corresponding higher degradation rate. In the present work, Mg reinforced PLA films with Mg content as high as 50 wt% were obtained without compromising the thermal stability of the polymer. Firstly, a successful dispersion of Mg microparticles was achieved by a breakthrough in processing introducing a colloidal step where organic additives were added to modify the Mg particle surface and promote a chemically stable suspension. The resulting colloidal suspension was then used as feedstock to obtain composite films by tape casting. The films show advantageous in vitro behaviour in terms of degradation, hydrogen release and oxygen permeability. In addition, the viability with fibroblast cells (MEF) opens a window of opportunity for these composite films as bioabsorbable material for tissue engineering and wound dressing applications. STATEMENT OF SIGNIFICANCE: Magnesium materials have extraordinary biodegradable properties and bioactive behavior due to release of Mg2+ ions, which offer a promising opportunity for their applicability as biomaterials for tissue regeneration. However, Mg is one of the most reactive metals with a high degradation rate. In contact with water produces H2, associated with a risk of failure of the implant. One alternative to minimize this drawback is the use of Mg particles surrounded by a biodegradable biocompatible polymer such as polylactic acid (PLA) to obtain PLA/Mg composites. In this work we processed Mg reinforced PLA in the shape of films that would be suitable for tissue regeneration. In vitro behavior of PLA/Mg films demonstrated that Mg2+ ions increase the fibroblast cells growth.

Development of novel zirconia implant's materials gradated design with improved bioactive surface.

Zirconia implants are becoming a preference choice for different applications such as knee, dental, among others. In order to improve osseointegration, implant's surfaces are usually coated with bioactive materials like hydroxyapatite (HAp) and beta-tricalcium phosphate (ß-TCP) that are very similar to the calcium phosphates found in bones. However, due to the implantation process, these coatings can be detached from the zirconia surface, leading to implant premature failure. In this work, a new component materials design aiming to avoid this coating detachment problem is proposed. It is based on the use of a bioactive zirconia-calcium phosphate composite outer layer onto the zirconia bulk, where the zirconia bulk provides mechanical strength and the outer layer provides biological performance. In order to assess the potential of this new materials design, two types of bioactive zirconia outer composite layers (zirconia reinforced by 10 vol% of HAp and by 10 vol% of ß-TCP) were produced by press and sinter process and the gradated samples were fully characterized concerning materials, mechanical resistance, fatigue resistance, and biological performance, as measured by different approaches. Results showed that the novel component materials design and the manufacturing process proposed for producing the bioactive zirconia samples with outer composite layers on zirconia bulk substrates are a promising solution for implants, with improved biological performance without substantially compromising their overall mechanical and fatigue properties.

Biofabrication of vessel-like structures with alginate di-aldehyde-gelatin (ADA-GEL) bioink.

One of the key challenges in the field of blood vessel engineering is the in vitro production of small and large diameter vessels. Considering that a combination of alginate di-aldehyde and gelatin (ADA-GEL) has been successfully applied for different biofabrication approaches, the aim of this study was to exploit ADA-GEL for the fabrication of vessel structures with diameters up to 4 mm. To explore plotting possibilities and to study the swelling behaviour, a library of vessel-like constructs with different diameters made from 2, 3 and 4% (w/v) alginate was created by using various hand-crafted double-needle extrusion systems. Vessel diameters were varied through changes of the double-needle core and outer diameters. A straightforward model for the production of vessel of different diameters from a variety of double-needle systems was established and vessel-constructs with diameters of up to 3.7 mm could be created. It was successfully demonstrated that an artificial vessel, consisting of an outer layer of 7.5% ADA50-GEL50 and an inner core of 3% gelatin, can support the proliferation and migration of an immobilized co-culture containing fibroblast (NHDF) and endothelial (HUVEC) cells. The openness and tightness of the hollow ADA-GEL structures were further confirmed by a dye injection test. Nanoindentation was performed to determine the Young's modulus of the used materials. Cell vitality was proved after 1, 2 and 3 weeks of incubation. The results showed a nearly twofold increase of viable cells per week. Fluorescent images confirmed cell migration during the whole incubation time.

Model of dissolution in the framework of tissue engineering and drug delivery.

Dissolution phenomena are ubiquitously present in biomaterials in many different fields. Despite the advantages of simulation-based design of biomaterials in medical applications, additional efforts are needed to derive reliable models which describe the process of dissolution. A phenomenologically based model, available for simulation of dissolution in biomaterials, is introduced in this paper. The model turns into a set of reaction-diffusion equations implemented in a finite element numerical framework. First, a parametric analysis is conducted in order to explore the role of model parameters on the overall dissolution process. Then, the model is calibrated and validated versus a straightforward but rigorous experimental setup. Results show that the mathematical model macroscopically reproduces the main physicochemical phenomena that take place in the tests, corroborating its usefulness for design of biomaterials in the tissue engineering and drug delivery research areas.

In silico design of magnesium implants: Macroscopic modeling.

Magnesium-based biomedical implants offer many advantages versus traditional ones although some challenges are still present. In this context, mathematical modeling and computational simulation may be a useful and complementary tool to evaluate in silico the performance of magnesium biomaterials under different conditions. In this paper, a phenomenologically-based model to simulate magnesium corrosion is developed. The model describes the physico-chemical interactions and evolution of species present in this phenomenon. A set of 7 species is considered in the model, which allows to simulate hydrogen release, pH evolution, corrosion products formation as well as degradation of magnesium. The model is developed under the continuum media theory and is implemented in a finite element framework. In the results section, the effect of model parameters on outcomes is firstly explored. Second, model results are qualitative validated versus two examples of application found in the literature. Two main conclusions are derived from this work: (i) the model captures well the experimental trends and allows to analyze the main variables present in magnesium corrosion, (ii) even though further validation is needed the model may be a useful standard in the design of degradable metal implants.

Bioactivity, mechanical properties and drug delivery ability of bioactive glass-ceramic scaffolds coated with a natural-derived polymer.

In this work, hybrid melanin-coated bioactive glass-ceramic multifunctional scaffolds were developed and characterized in terms of mechanical strength, in vitro bioactivity in simulated body fluid (SBF) and ability to load ibuprofen. The coated scaffolds exhibited an accelerated bioactivity in comparison with the uncoated ones, being able of developing hydroxyapatite-like crystals after 7days soaking in simulated body fluid (SBF). Besides its positive influence on the scaffolds bioactivity, the melanin coating was able to enhance their mechanical properties, increasing the initial compressive strength by a factor of >2.5. Furthermore, ibuprofen was successfully loaded on this coating, allowing a controlled drug release of the anti-inflammatory agent.

Development of a bioactive glass-polymer composite for wound healing applications.

This study reports the production and characterization of a composite material for wound healing applications. A bioactive glass obtained by sol-gel process and doped with two different metal ions was investigated. Silver (Ag) and cobalt (Co) were chosen due to their antibacterial and angiogenic properties, respectively, very beneficial in the wound healing process. Poly(ε-caprolactone) (PCL) fibers were produced by electrospinning (ES) from a polymeric solution using acetone as a solvent. After optimization of the ES parameters, two main suspensions were prepared, namely: PCL containing bioactive glass nanoparticles (BG-NP) and PCL with Ag2O and CoO doped BG-NP (DP BG-NP), which were processed with different concentrations of BG-NP (0.25%, 0.5% and 0.75wt%). The composite membranes were characterized in terms of morphology, fiber diameter, weight loss, mineralization potential and mechanical performance.

Direct ink writing of silica-bonded calcite scaffolds from preceramic polymers and fillers.

Silica-bonded calcite scaffolds have been successfully 3D-printed by direct ink writing, starting from a paste comprising a silicone polymer and calcite powders, calibrated in order to match a SiO2/CaCO3 weight balance of 35/65. The scaffolds, fabricated with two slightly different geometries, were first cross-linked at 350 °C, then fired at 600 °C, in air. The low temperature adopted for the conversion of the polymer into amorphous silica, by thermo-oxidative decomposition, prevented the decomposition of calcite. The obtained silica-bonded calcite scaffolds featured open porosity of about 56%-64% and compressive strength of about 2.9-5.5 MPa, depending on the geometry. Dissolution studies in SBF and preliminary cell culture tests, with bone marrow stromal cells, confirmed the in vitro bioactivity of the scaffolds and their biocompatibility. The seeded cells were found to be alive, well anchored and spread on the samples surface. The new silica-calcite composites are expected to be suitable candidates as tissue-engineering 3D scaffolds for regeneration of cancellous bone defects.