ABSTRACT
To date, thermal nanoimprint lithography (NIL) for patterning hybrid perovskites has always involved an intricate etching step of a hard stamp material or its master. Here, we demonstrate for the first time the successful nanopatterning of a perovskite film by NIL with a low-cost polymeric stamp. The stamp consists of a dichromated gelatin grating structured by holographic lithography. The one-dimensional grating is imprinted into a perovskite film at 95 °C and 90 MPa for 10 min, resulting in a high quality second-order distributed feedback (DFB) laser. The laser exhibits an excellent performance with a threshold of 81 µJ/cm2, a line width of 0.32 nm, and a pronounced linear polarization. This novel approach enables cost-effective fabrication of high-quality DFB lasers compatible with different perovskite compositions and photonic nanostructures for a wide range of applications.
ABSTRACT
The spectral overlap between stimulated emission (SE) and absorption from dark states (i.e. charges and triplets) especially in the near-infrared (NIR), represents one of the most effective gain loss channels in organic semiconductors. Recently, bottom-up synthesis of atomically precise graphene nanostructures, or nanographenes (NGs), has opened a new route for the development of environmentally and chemically stable materials with optical gain properties. However, also in this case, the interplay between gain and absorption losses has hindered the attainment of efficient lasing action in the NIR. Here, we demonstrate that the introduction of two fluoranthene imide groups to the NG core leads to a more red-shifted emission than the precursor NG molecule (685 vs. 615 nm) and also with a larger Stokes shift (45 nm vs. 2 nm, 1026 cm-1vs. 53 cm-1, respectively). Photophysical results indicate that, besides the minimisation of ground state absorption losses, such substitution permits to suppress the detrimental excited state absorption in the NIR, which likely arises from a dark state with charge-transfer character and triplets. This has enabled NIR lasing (720 nm) from all-solution processed distributed feedback devices with one order of magnitude lower thresholds than those of previously reported NIR-emitting NGs. This study represents an advance in the field of NGs and, in general, organic semiconductor photonics, towards the development of cheap and stable NIR lasers.
ABSTRACT
The molecule N,N'-bis(3-methylphenyl)-N,N'-dyphenylbenzidine (TPD) has been widely used in optoelectronic applications, mainly for its hole-transporting properties, but also for its capability to emit blue light and amplified spontaneous emission, which is important for the development of organic lasers. Here, we report deep-blue-emitting distributed feedback (DFB) lasers based on TPD dispersed in polystyrene (PS), as active media, and dichromated gelatin layers with holographically engraved relief gratings, as laser resonators. The effect of the device architecture (with the resonator located below or on top of the active layer) is investigated with a dye (TPD) that can be doped into PS at higher rates (up to 60 wt%), than with previously used dyes (<5 wt%). This has enabled changing the index contrast between film and resonator, which has an important effect on the laser performance. With regards to thresholds, both architectures behave similarly for TPD concentrations above 20 wt%, while for lower concentrations, top-layer resonator devices show lower values (around half). Remarkably, the operational durability of top-layer resonator devices is larger (in a factor of around 2), independently of the TPD concentration. This is a consequence of the protection offered by the resonator against dye photo-oxidation when the device is illuminated with pulsed UV light.
ABSTRACT
High-transparency polymers, called optical polymers (OPs), are used in many thin-film devices, for which the knowledge of film thickness (h) and refractive index (n) is generally required. Spectrophotometry is a cost-effective, simple and fast non-destructive method often used to determine these parameters simultaneously, but its application is limited to films where h > 500 nm. Here, a simple spectrophotometric method is reported to obtain simultaneously the n and h of a sub-micron OP film (down to values of a few tenths of a nm) from its transmission spectrum. The method is valid for any OP where the n dispersion curve follows a two-coefficient Cauchy function and complies with a certain equation involving n at two different wavelengths. Remarkably, such an equation is determined through the analysis of n data for a wide set of commercial OPs, and its general validity is demonstrated. Films of various OPs (pristine or doped with fluorescent compounds), typically used in applications such as thin-film organic lasers, are prepared, and n and h are simultaneously determined with the proposed procedure. The success of the method is confirmed with variable-angle spectroscopic ellipsometry.
ABSTRACT
Chemically synthesized zigzag-edged nanographenes (NG) have recently demonstrated great success as the active laser units in solution-processed organic distributed feedback (DFB) lasers. Here, we report the first observation of dual amplified spontaneous emission (ASE) from a large-size NG derivative (with 12 benzenoid rings) dispersed in a polystyrene film. ASE is observed simultaneously at the 685 and 739 nm wavelengths, which correspond to different transitions of the photoluminescence spectrum. Ultrafast pump-probe spectroscopy has been used to ascertain the underlying photophysical processes taking place in the films. DFB lasers, based on these materials and top-layer nanostructured polymeric resonators (i.e., one or two-dimensional surface relief gratings), have been fabricated and characterized. Lasers emitting close to either one of the two possible ASE wavelengths, or simultaneously at both of them, have been prepared by proper selection of the resonator parameters.
ABSTRACT
Perylene-fused, aggregation-free polycyclic aromatic hydrocarbons with partial zigzag periphery (ZY-01, ZY-02, and ZY-03) were synthesized. X-ray crystallographic analysis reveals that there is no intermolecular π-π stacking in any of the three molecules, and as a result, they show moderate-to-high photoluminescence quantum yield in both solution and in the solid state. They also display the characteristic absorption and emission spectra of perylene dyes. ZY-01 and ZY-02 with a nearly planar π-conjugated skeleton exhibit amplified spontaneous emission (ASE) when dispersed in polystyrene thin films. Solution-processed distributed feedback lasers have been fabricated using ZY-01 and ZY-02 as active gain materials, both showing narrow emission linewidth (<0.4â nm) at wavelengths around 515 and 570â nm, respectively. In contrast, ZY-03 did not show ASE and lasing, presumably due to its highly twisted backbone, which facilitates nonradiative internal conversion and intersystem crossing.
ABSTRACT
Surface-emitting distributed feedback (DFB) lasers with both, resonator and active material based on solution-processable polymers, are attractive light sources for a variety of low-cost applications. Besides, the lasers should have competitive characteristics compared to devices based on high-quality inorganic resonators. Here, we report high performing all-solution-processed organic DFB lasers, consisting of water-processed photoresist layers with surface relief gratings located over the active films, whose emission properties can be finely tuned through resonator design. Their laser threshold and efficiency are simultaneously optimized by proper selection of residual resist thickness and grating depth, d. Lowest thresholds and largest efficiencies are obtained when there is no residual layer, while a trade-off between threshold and efficiency is found in relation to d, because both parameters decrease with decreasing d. This behaviour is successfully explained in terms of an overlap factor r, defined to quantify the interaction strength between the grating and the light emitted by the active film and traveling along it, via the evanescent field. It is found that optimal grating depths are in the range 100-130 nm (r ~ 0.5-0.4). Overall, this study provides comprehensive design rules towards an accurate control of the emission properties of the reported lasers.
ABSTRACT
The chemical synthesis of nanographene molecules constitutes the bottom-up approach toward graphene, simultaneously providing rational chemical design, structure-property control and exploitation of their semiconducting and luminescence properties. Here, we report nanographene-based lasers from three zigzag-edged polycyclic aromatics. The devices consist of a passive polymer film hosting the nanographenes and a top-layer polymeric distributed feedback resonator. Both the active material and the laser resonator are processed from solution, key for the purpose of obtaining low-cost devices with mechanical flexibility. The prepared lasers show narrow linewidth ( < 0.13 nm) emission at different spectral regions covering a large segment of the visible spectrum, and up to the vicinity of the near-infrared. They show outstandingly long operational lifetimes (above 105 pump pulses) and very low thresholds. These results represent a significant step forward in the field of graphene and broaden its versatility in low-cost devices implying light emission, such as lasers.