ABSTRACT
Fatty acids (FAs) and fatty acid methyl esters (FAMEs) co-occur in many samples, and analysis of both substance classes is frequently of high interest. To this end, this study introduces the first method for simultaneous determination of FAs and FAMEs including fully automated solvent-free solid-phase microextraction (SPME) arrow headspace extraction combined with isotope-labeling in situ FA derivatization with deuterated methanol (CD3OD). By using the chromatographic isotope effect (ΔRt = 0.03 min) and the + 3 m/z mass shift, FAs can be selectively differentiated from the FAMEs during gas chromatography tandem-mass spectrometry (GC-MS/MS) operated in the multiple reaction monitoring (MRM) aquisition mode. Additionally, an approach is presented to predict the retention times of deuterated compounds. Optimization of the derivatization conditions was accomplished by design of experiments and found to be 20 min, 50 °C, 4 v/v% CD3OD, and pH 2.1. During method validation, FAs and FAMEs were calibrated in different concentration ranges by standard addition in five real matrices and ultrapure water leading to good linearities and method detection limits for FAs ranging from 1-30 µg L-1 and for FAMEs from 0.003-0.72 µg L-1. FAs and FAMEs were detected in real samples from surface water, wastewater treatment plant effluent, and three different bioreactor samples and could be quantified in concentrations ranging from 2-1056 µg L-1 for FAs and 0.01-14 µg L-1 for FAMEs.
ABSTRACT
The analysis of fatty acid methyl esters (FAMEs) is of high relevance for monitoring and control of various industrial processes and biological systems. In this study, a novel, green analytical approach for the determination of 24 FAMEs from aqueous samples is proposed, which is based on a headspace solid-phase microextraction (SPME) arrow followed by gas chromatography coupled to tandem mass spectrometry (GC-MS/MS). The method was substantially accelerated to a run time of 44 min per sample by thorough optimization and automation of the relevant parameters. The limiting parameters, mostly based on expediting equilibrium attainment, were found to be parameters of extraction: material, pH, time, and temperature, which were optimized to divinylbenzene polydimethylsiloxane (DVB-PDMS), pH 2, 20 min, and 70 °C, respectively. The optimization and automation of the method led to low method detection limits (9-437 ng L-1) and high selectivity. Evaluation of the method on real samples was done by analyzing the aqueous phase of a bioreactor, whereby the matrix effect could be greatly reduced due to dilution and headspace sampling. The rapid, sensitive, selective, and matrix-reduced approach is found to be not only a novel method for water analysis but is promising for further applications, e.g., with solid and gaseous samples containing FAMEs.
Subject(s)
Solid Phase Microextraction , Tandem Mass Spectrometry , Automation , Fatty Acids , Gas Chromatography-Mass Spectrometry/methods , Solid Phase Microextraction/methods , WaterABSTRACT
Hydrogen is a promising energy source that is believed to replace the conventional energy sources e.g. fossil fuels over years. Hydrogen production methods can be divided into conventional production methods which depend mainly on fossil fuels and alternative production methods including electrolysis of water, biophotolysis and fermentation hydrogen production from organic waste materials. Compared to the conventional methods, the alternative hydrogen production methods are less energy intensive and negative-value substrates i.e. waste materials can be used to produce hydrogen. Among the alternative methods, fermentation process including dark and photo-fermentation has gained more attention because these processes are simple, waste materials can be utilized, and high hydrogen yields can be achieved. The fermentation process is affected by several parameters such as type of inoculum, pH, temperature, substrate type and concentration, hydraulic retention time, etc. In order to achieve optimum hydrogen yields and maximum substrate degradation, the operating conditions of the fermentation process must be optimized. In this review, two routes for biohydrogen production as dark and photo-fermentation are discussed. Dark/photo-fermentation technology is a new approach that can be used to increase the hydrogen yield and improve the energy recovery from organic wastes.
Subject(s)
Fermentation , Hydrogen/metabolism , Biofuels , Bioreactors , Economics , Fossil Fuels , Glucose , Hydrogen-Ion Concentration , Temperature , Waste ProductsABSTRACT
In this study, the effect of pre-treatments including alkaline, acid and hydrogen peroxide on continuous hydrogen and methane production was investigated. Two different substrates as potatoes and bean wastes were used. Pre-treatment showed positive effect on bio-hydrogen and bio-methane production; higher bio-hydrogen and bio-methane production results using pre-treated samples than the control bioreactors (without pre-treatment), were recorded. In case of potatoes wastes, the hydrogen yield ranged between 126.4 and 252.7â¯mL-H2/g-TVS using pre-treated samples compared to 58.7â¯mL-H2/g-TVS observed in the reference test. Pre-treated bean wastes showed hydrogen yield of 93.0-152.1â¯mL-H2/g-TVS higher than 53.3â¯mL-H2/g-TVS measured in the control test. In the second stage, average methane yield results of 322.9-507.1 and 284.3-462.6â¯mL-CH4/g-TVS higher than 198.6 and 124.3â¯mL-CH4/g-TVS measured for potatoes and bean wastes control bioreactors, respectively. The best results were observed using H2O2 pre-treatment. The energy production efficiency was improved by combining H2 and CH4 bioreactors.