Automated analysis of trapeziometacarpal joint kinematics using four-dimensional computed tomography.

The aim of this study was to develop an automated approach model to define in vivo kinematics of the trapeziometacarpal (TMC) joint using four-dimensional computed tomography. A total of 15 healthy volunteers were included and their TMC joint kinematics were studied during a retropulsion-opposition-retropulsion movement. We used cardan angles estimated from transformation matrices using a ZYX-decomposition and analysed the motion of the thumb metacarpal relative to the trapezium, the thumb metacarpal relative to the index metacarpal, and the trapezium relative to the index metacarpal. The study also included an analysis of the joint hysteresis effect and a joint proximity model that estimated the joint contact area during a retropulsion-opposition-retropulsion movement. The automated approach significantly decreased the time needed to analyse each case and makes this model applicable for further research on TMC kinematics.

Impact of vessel morphology on CT-derived fractional-flow-reserve in non-obstructive coronary artery disease in right coronary artery.

OBJECTIVES: Computed tomography (CT)-derived fractional flow reserve (FFRCT) decreases continuously from proximal to distal segments of the vessel due to the influence of various factors even in non-obstructive coronary artery disease (NOCAD). It is known that FFRCT is dependent on vessel-length, but the relationship with other vessel morphologies remains to be explained. PURPOSE: To investigate morphological aspects of the vessels that influence FFRCT in NOCAD in the right coronary artery (RCA). METHODS: A total of 443 patients who underwent both FFRCT and invasive coronary angiography, with < 50% RCA stenosis, were evaluated. Enrolled RCA vessels were classified into two groups according to distal FFRCT: FFRCT ≤ 0.80 (n = 60) and FFRCT > 0.80 (n = 383). Vessel morphology (vessel length, lumen diameter, lumen volume, and plaque volume) and left-ventricular mass were assessed. The ratio of lumen volume and vessel length was defined as V/L ratio. RESULTS: Whereas vessel-length was almost the same between FFRCT ≤ 0.80 and > 0.80, lumen volume and V/L ratio were significantly lower in FFRCT ≤ 0.80. Distal FFRCT correlated with plaque-related parameters (low-attenuation plaque, intermediate-attenuation plaque, and calcified plaque) and vessel-related parameters (proximal and distal vessel diameter, vessel length, lumen volume, and V/L ratio). Among all vessel-related parameters, V/L ratio showed the highest correlation with distal FFRCT (r = 0.61, p < 0.0001). Multivariable analysis showed that calcified plaque volume was the strongest predictor of distal FFRCT, followed by V/L ratio (ß-coefficient = 0.48, p = 0.03). V/L ratio was the strongest predictor of a distal FFRCT ≤ 0.80 (cut-off 8.1 mm3/mm, AUC 0.88, sensitivity 90.0%, specificity 76.7%, 95% CI 0.84-0.93, p < 0.0001). CONCLUSIONS: Our study suggests that V/L ratio can be a measure to predict subclinical coronary perfusion disturbance. CLINICAL RELEVANCE STATEMENT: A novel marker of the ratio of lumen volume to vessel length (V/L ratio) is the strongest predictor of a distal CT-derived fractional flow reserve (FFRCT) and may have the potential to improve the diagnostic accuracy of FFRCT. KEY POINTS: • Physiological FFRCT decline depends not only on vessel length but also on the lumen volume in non-obstructive coronary artery disease in the right coronary artery. • FFRCT correlates with plaque-related parameters (low-attenuation plaque, intermediate-attenuation plaque, and calcified plaque) and vessel-related parameters (proximal and distal vessel diameter, vessel length, lumen volume, and V/L ratio). • Of vessel-related parameters, V/L ratio is the strongest predictor of a distal FFRCT and an optimal cut-off value of 8.1 mm3/mm.

Robotically Aided Method to Characterise the Soft Tissue Interaction with Wearable Robots.

Wearable robots are widely used to enhance, support or assist humans in different tasks. To accomplish this scope, the interaction between the human body and the device should be comfortable, smooth, high-efficient to transfer forces, and safe for the user. Nevertheless, the pressure and shear stress related to these goals have been overlooked or partially analysed. In this sense, it is crucial to understand the soft tissue response through the in-vivo characterisation of multiple areas of the human body. In fact, soft tissue characterisation plays an essential role in calculating the pressure distribution and shear stress. However, current approaches to estimating soft tissue properties are unsuitable for deployment with multiple human body areas. Hence, this work presents a novel methodology to ease the characterisation of soft tissues using a robotic arm and a 3D superficial scanner. First, the robotic arm is validated by comparing the tensile and compression tests to the indentation tests done by the robot, estimating a 10,4% error. The preliminary experimental tests present the hyperelastic model which fit two adjacent zones of the forearm. This analysis can be extended in several ways, such as: calculating the shear stress, the energy losses or deformations caused by the interaction, and investigating the pressure distribution of different types of physical interfaces.

Quantitative hemodynamic assessment of stenotic below-the-knee arteries using spatio-temporal bolus tracking on 4D-CT angiography.

BACKGROUND: Peripheral arterial disease (PAD) is a chronic occlusive disease that restricts blood flow in the lower limbs, causing partial or complete blockages of the blood flow. While digital subtraction angiography (DSA) has traditionally been the preferred method for assessing blood flow in the lower limbs, advancements in wide beam Computed Tomography (CT), allowing successive acquisition at high frame rate, might enable hemodynamic measurements. PURPOSE: To quantify the arterial blood flow in stenotic below-the-knee (BTK) arteries. To this end, we propose a novel method for contrast bolus tracking and assessment of quantitative hemodynamic parameters in stenotic arteries using 4D-CT. METHODS: Fifty patients with suspected PAD underwent 4D-CT angiography in addition to the clinical run-off computed tomography angiography (CTA). From these dynamic acquisitions, the BTK arteries were segmented and the region of maximum blood flow was extracted. Time attenuation curves (TAC) were estimated using 2D spatio-temporal B-spline regression, enforcing both spatial and temporal smoothness. From these curves, quantitative hemodynamic parameters, describing the shape of the propagating contrast bolus were automatically extracted. We evaluated the robustness of the proposed TAC fitting method with respect to interphase delay and imaging noise and compared it to commonly used approaches. Finally, to illustrate the potential value of 4D-CT, we assessed the correlation between the obtained hemodynamic parameters and the presence of PAD. RESULTS: 280 out of 292 arteries were successfully segmented, with failures mainly due to a delayed contrast arrival. The proposed method led to physiologically plausible hemodynamic parameters and was significantly more robust compared to 1D temporal regression. A significant correlation between the presence of proximal stenoses and several hemodynamic parameters was found. CONCLUSIONS: The proposed method based on spatio-temporal bolus tracking was shown to lead to stable and physiologically plausible estimation of quantitative hemodynamic parameters, even in the case of stenotic arteries. These parameters may provide valuable information in the evaluation of PAD and contribute to its diagnosis.

Dynamic CT scanning of the knee: Combining weight bearing with real-time motion acquisition.

BACKGROUND: Imaging the lower limb during weight-bearing conditions is essential to acquire advanced functional joint information. The horizontal bed position of CT systems however hinders this process. The purpose of this study was to validate and test a device to simulate realistic knee weight-bearing motion in a horizontal position during dynamic CT acquisition and process the acquired images. METHODS: "Orthostatic squats" was compared to "Horizontal squats" on a device with loads between 35% and 55% of the body weight (%BW) in 20 healthy volunteers. Intraclass Correlation Coefficient (ICC), and standard error of measurement (SEM), were computed as measures of the reliability of curve kinematic and surface EMG (sEMG) data. Afterwards, the device was tested during dynamic CT acquisitions on three healthy volunteers and three patients with patellofemoral pain syndrome. The respective images were processed to extract Tibial-Tuberosity Trochlear-Groove distance, Bisect Offset and Lateral Patellar Tilt metrics. RESULTS: For sEMG, the highest average ICCs (SEM) of 0.80 (6.9), was found for the load corresponding to 42%BW. Kinematic analysis showed ICCs were the highest for loads of 42%BW during the eccentric phase (0.79-0.87) and from maximum flexion back to 20° (0.76). The device proved to be safe and reliable during the acquisition of dynamic CT images and the three metrics were computed, showing preliminary differences between healthy and pathological participants. CONCLUSIONS: This device could simulate orthostatic squats in a horizontal position with good reliability. It also successfully provided dynamic CT scan images and kinematic parameters of healthy and pathological knees during weight-bearing movement.

Combined evaluation of blood flow and tissue perfusion in diabetic feet by intra-arterial dynamic 4DCT imaging.

Critical limb ischemia is associated with high mortality and major amputations. Intra-arterial digital subtraction angiography (IADSA) has been the reference standard but has some shortcomings including the two-dimensional projection and the lack of tissue perfusion information. The aim of this exploratory study is to examine four-dimensional computed tomography (4DCT) angiography and perfusion imaging using low-volume intra-arterial contrast injections for an improved anatomic and hemodynamic assessment in patients with foot ulcers. Three patients underwent a low-volume (2 mL) intra-arterial contrast-enhanced 4DCT examination combined with a diagnostic IADSA. An automated assessment of blood flow and tissue perfusion from the 4DCT data was performed. Vascular structures and corresponding blood flows were successfully assessed and correlated well with the IADSA results. Perfusion values of the affected tissue were significantly higher compared to the unaffected tissue. The proposed 4DCT protocol combined with the minimal usage of contrast agent (2 mL) provides superior images compared to IADSA as three phases (arterial, perfusion, and venous) are captured. The obtained parameters could allow for an improved diagnosis of critical limb ischemia as both the proximal vasculature and the extent of the perfusion deficit in the microvasculature can be assessed.Relevance statementIntra-arterial 4DCT allows for assessing three phases (arterial, perfusion and venous) using minimal contrast (2 mL). This method could lead to an improved diagnosis of critical limb ischemia as both proximal vasculature and the extent of the perfusion deficit are assessed.Trial registrationISRCTN, ISRCTN95737449. Registered 14 March 2023-retrospectively registered, https://www.isrctn.com/ISRCTN95737449 Key points• Three phases (arterial, perfusion, and venous) are obtained from 2 mL intra-arterial 4DCT.• The obtained hemodynamic parameters correlated well with the IADSA findings.• 4DCT surpassed IADSA in terms of assessment of venous blood flow and inflammatory hyperperfusion.• The assessment of tissue perfusion could lead to optimizing the revascularization strategy.

The impact of iodine contrast agent on radiation dose of heart and blood: a comparison between coronary CT angiography and cardiac calcium scoring CT.

BACKGROUND: Iodine contrast agent (CA) is widely used in cardiac computed tomography (CT). The CA can increase the organ radiation doses due to the photoelectric effect. PURPOSE: To investigate the impact of CA on radiation dose in cardiac CT by comparing the radiation dose between contrast coronary CT angiography (CCTA) and non-contrast calcium scoring CT (CSCT). MATERIAL AND METHODS: Radiation doses were computationally calculated for 30 individual patients who received CSCT and CCTA in the same exam session. The geometry and acquisition parameters were modeled in the simulations based on individual patient CT images and acquisitions. Doses in the presence and absence of CA were obtained in the aorta, left ventricle (LV), right ventricle (RV), and myocardial tissue (MT). The dose values were normalized by size-specific dose estimate (SSDE). The dose enhancement factors (DEFSSDE) were calculated as the ratio of doses in CCTA over doses in CSCT. RESULTS: Compared to the CSCT scans, doses increase in the CCTA scans in the aorta (DEFSSDE = 2.14 ± 0.20), LV (DEFSSDE = 1.78 ± 0.26), and RV (DEFSSDE = 1.31 ± 0.22). A linear relation is observed between the local CA concentrations and the dose increase in the heart; DEFSSDE = 0.07*I(mg/mL) + 0.80 (R2 = 0.8; p < 0.01). The DEFSSDE in the MT (DEFSSDE = 0.96 ± 0.08) showed no noticeable impact of CA on the dose in this tissue. In addition, patient variability in the dose distributions was observed. CONCLUSION: A linear causal relation exists between local CA concentration and increase in radiation dose in cardiac CT. For the same CT exposure, dose to the heart is on average 55% higher in contrast cardiac CT.

Stent appearance in a novel silicon-based photon-counting CT prototype: ex vivo phantom study in head-to-head comparison with conventional energy-integrating CT.

BACKGROUND: In this study, stent appearance in a novel silicon-based photon-counting computed tomography (Si-PCCT) prototype was compared with a conventional energy-integrating detector CT (EIDCT) system. METHODS: An ex vivo phantom was created, consisting of a 2% agar-water mixture, in which human-resected and stented arteries were individually embedded. Using similar technique parameters, helical scan data was acquired using a novel prototype Si-PCCT and a conventional EIDCT system at a volumetric CT dose index (CTDIvol) of 9 mGy. Reconstructions were made at 502 and 1502 mm2 field-of-views (FOVs) using a bone kernel and adaptive statistical iterative reconstruction with 0% blending. Using a 5-point Likert scale, reader evaluations were performed on stent appearance, blooming and inter-stent visibility. Quantitative image analysis was performed on stent diameter accuracy, blooming and inter-stent distinction. Qualitative and quantitative differences between Si-PCCT and EIDCT systems were tested with a Wilcoxon signed-rank test and a paired samples t-test, respectively. Inter- and intra-reader agreement was assessed using the intraclass correlation coefficient (ICC). RESULTS: Qualitatively, Si-PCCT images were rated higher than EIDCT images at 150-mm FOV, based on stent appearance (p = 0.026) and blooming (p = 0.015), with a moderate inter- (ICC = 0.50) and intra-reader (ICC = 0.60) agreement. Quantitatively, Si-PCCT yielded more accurate diameter measurements (p = 0.001), reduced blooming (p < 0.001) and improved inter-stent distinction (p < 0.001). Similar trends were observed for the images reconstructed at 50-mm FOV. CONCLUSIONS: When compared to EIDCT, the improved spatial resolution of Si-PCCT yields enhanced stent appearance, more accurate diameter measurements, reduced blooming and improved inter-stent distinction. KEY POINTS: • This study evaluated stent appearance in a novel silicon-based photon-counting computed tomography (Si-PCCT) prototype. • Compared to standard CT, Si-PCCT resulted in more accurate stent diameter measurements. • Si-PCCT also reduced blooming artefacts and improved inter-stent visibility.

Influence of medial and lateral imaging plane inclination on assessment of trochlear depth, sulcus angle, and facet asymmetry in the setting of trochlear anatomy: a cadaveric study.

PURPOSE: (1) to assess the influence of medial or lateral imaging plane inclination on the measurement of sulcus angle, trochlear depth, and facet asymmetry on transverse cross-sectional images. (2) to assess the effect of measurement level (height) on these respective parameters. MATERIALS AND METHODS: Twenty dry femurs (9 left, 11 right) were imaged with CT. A 3D dataset was obtained from which axial images were reconstructed in the ideal plane without inclination as well as with 8° of medial and lateral inclination. Sulcus angle, trochlear depth, and facet asymmetry were measured on the 3 image sets. In addition, the measurements were performed at 5 mm and 10 mm from the superior margin of the medial trochlear facet. Statistical analysis consisted of the Wilcoxon test and calculation of measurement variation. RESULTS: There were no statistically significant differences between the indicated measurements on the reference set compared to medial or lateral inclination. All measurements were significantly different depending on measurement height. CONCLUSION: Medial or lateral inclination in the transverse imaging plane of 8° does not influence the values of typical parameters used for the assessment of trochlear dysplasia. The measurement height has a significant influence, and a consensus should be found as to which is the optimal measurement height.

Physical activity increases synovial fluid in ankle tendon sheaths: an adjustment of MR Criteria is needed.

OBJECTIVES: To compare the amount of fluid in synovial sheaths of the ankle before and after running. Our hypothesis was that this amount would increase and that the threshold for what is normally acceptable should be adjusted after physical activity. METHODS: Twenty-one healthy volunteers (n = 42 ankles) ran for 40 min on a treadmill. They underwent 3 T MRI before and immediately after running using a dedicated ankle coil. The images were stored and subsequently measured in a standardized way and independently read by two readers for fluid in the tendon sheaths in the retro and inframalleolar area. Statistics were performed for each tendon (Wilcoxon signed rank test), and also for the pooled data. Intraclass correlation coefficients were calculated. RESULTS: For reader 1, for all tendons the values after running increased without reaching statistical significance. For reader 2 this was not the case for all tendons but for most. When all the data were pooled (n = 800 measurements), the statistical difference before and after running was significant (p < 0.001). CONCLUSION: Data pre and post-running show a trend of increasing synovial fluid, however, not significant for each individual tendon. The pooled data for all tendons, (n = 800) show a statistically significant increase after running (p < 0.001). The clinical implication is that the threshold for normally acceptable fluid should be adjusted if the patient undergoes an MR study after recent physical activity.

A patient- and acquisition-tailored injection approach for improving consistency of CT enhancement towards a target CT value in coronary CT angiography.

BACKGROUND: Unoptimized coronary CT angiography (CTA) exams typically result in a highly variable arterial enhancement (HUa ) across patients. This study aimed at harmonizing arterial enhancement by implementing a patient-, contrast- and kV-tailored injection protocol. METHODS: First, the optimal body size metric to predict HUa was identified by retrospectively analysing images of 76 patients, acquired with 70 ml contrast media (G1). Second, using phantom experiments, correction factors for the effect of kV and contrast concentration on HUa were determined. Third, a model was developed, prescribing the optimal contrast dose to be injected to obtain a diagnostically appropriate arterial target enhancement HUtarget . The model was then validated on 278 prospectively collected patients, in two groups with two different HUtarget : 525 HU (207 patients, G2A) and 425 HU (71 patients, G2B). The HUa histograms were compared among groups and to the target enhancement through their mean and standard deviation (SD) at 100 kVp reference level. Also, signal-to-noise ratio was obtained and compared among the groups. RESULTS: Fat free mass (FFM) showed the highest correlation with HUa (r = 0.69). KVp correction factors ranged from 0.65 at 70 kVp to 1.22 at 140 kVp. The obtained model reduced the group heterogeneity (SD) from 101HU for reference G1 to 75HU (p < 0.001) for G2A and 68HU (p < 0.001) for G2B. The mean HUa of 506HU in G2A was slightly below HUtarget  = 525HU (p = 0.01) whereas in G2B, the mean HUa of 414HU was not significantly different from HUtarget  = 425HU (p = 0.54). The total iodine dose was lowered from 19.5 g-I to 17.6 g-I and 14.2 g-I from G1 to G2A and G2B, on average. CONCLUSION: A contrast injection model, based on patient's fat free mass and accounting for the contrast agent concentration and the planned CT-scan tube voltage, harmonized arterial enhancement among patients towards a predefined target enhancement in coronary CTA scanning, without affecting the bolus timing.

Impact of coronary bifurcation angle on computed tomography derived fractional flow reserve in coronary vessels with no apparent coronary artery disease.

OBJECTIVES: Computed tomography (CT) derived fractional flow reserve (FFRCT) decreases from the proximal to the distal part due to a variety of factors. The energy loss due to the bifurcation angle may potentially contribute to a progressive decline in FFRCT. However, the association of the bifurcation angle with FFRCT is still not entirely understood. This study aimed to investigate the impact of various bifurcation angles on FFRCT decline below the clinically crucial relevance of 0.80 in vessels with no apparent coronary artery disease (CAD). METHODS: A total of 83 patients who underwent both CT angiography including FFRCT and invasive coronary angiography, exhibiting no apparent CAD were evaluated. ΔFFRCT was defined as the change in FFRCT from the proximal to the distal in the left anterior descending artery (LAD) and left circumflex artery (LCX). The bifurcation angle was calculated from three-dimensional volume rendered images. Vessel morphology and plaque characteristics were also assessed. RESULTS: ΔFFRCT significantly correlated with the bifurcation angle (LAD angle, r = 0.35, p = 0.001; LCX angle, r = 0.26, p = 0.02) and vessel length (LAD angle, r = 0.30, p = 0.005; LCX angle, r = 0.49, p < 0.0001). In LAD, vessel length was the strongest predictor for distal FFRCT of ≤ 0.80 (ß-coefficient = 0.55, p = 0.0003), immediately followed by the bifurcation angle (ß-coefficient = 0.24, p = 0.02). The bifurcation angle was a good predictor for a distal FFRCT ≤ 0.80 (LAD angle, cut-off 31.0°, AUC 0.70, sensitivity 74%, specificity 68%; LCX angle, cut-off 52.6°, AUC 0.86, sensitivity 88%, specificity 85%). CONCLUSIONS: In vessels with no apparent CAD, vessel length was the most influential factor on FFRCT, directly followed by the bifurcation angle. KEY POINTS: • Both LAD and LCX bifurcation angles are factors influencing FFR CT. • Bifurcation angle is one of the predictors of a distal FFRCT of ≤ 0.80 and an optimal cut-off value of 31.0° for the LAD and 52.6° for the LCX. • Bifurcation angle should be taken into consideration when interpreting numerical values of FFRCT.

The use of dynamic CT imaging for tracking mandibular movements in a phantom.

Purpose. The objective of this study was to analyse the possibilities of using 4D CT scanning for the tracking of patients' mandibles.Methods. A clinical 256-slice Revolution CT was used in obtaining 4D CT scans without table movement, with a novel mandibular phantom, mounted on a programmable six degrees-of-freedom Stewart Platform in motion. The phantom was used to simulate mandibular motions which are combinations of rotations with translations (depression, elevation, protrusion, retrusion and laterotrusion). The phantom was scanned five times during identical motion patterns with a dynamic CT acquisition protocol. An image processing workflow consisting of a pairwise rigid registration and semi-automatic segmentation was developed to extract kinematic parameters (cardan angles and point-of-interest displacements) from the dynamic sequences. Reproducibility was investigated by the 95% confidence interval and the absorbed organ dose to organs of interest in the primary beam were also estimated and compared to those of a standard CT scan of the brainResults. The maximum average 95% confidence interval for the displacement across all time points for the five repetitions was 0.61 mm (Yaxis). In terms of rotations, the maximum average 95% confidence interval across all time points for the five repetitions was 1.39° (Xaxis). The effective dose for the dynamic scan was found to be 1.3 mSv, for a CTDIvolof 63.95 mGy and a DLP of 1023.14 mGycm. The absorbed organ doses were similar to organ doses during a clinical head CT scan.Conclusions. A framework is proposed to use 4D CT scanning as a possible methodology to evaluate the motion of the temporomandibular joint. The scanning protocol allows to visualise the motion by applying a semi-automated segmentation and registration. A graphical representation of all displacements in the three spatial dimensions can depict multiple points-of-interest at once during the same acquisition. A novel type of phantom was also introduced which simulates mandibular movement with six degrees-of-freedom (three translations and three rotations).

The use of cardiac CT acquisition mode for dynamic musculoskeletal imaging.

OBJECTIVES: To quantitatively evaluate the impact of a cardiac acquisition CT mode on motion artifacts in comparison to a conventional cine mode for dynamic musculoskeletal (MSK) imaging. METHODS: A rotating PMMA phantom with air-filled holes drilled at varying distances from the disk center corresponding to linear hole speeds of 0.75 cm/s, 2.0 cm/s, and 3.6 cm/s was designed. Dynamic scans were obtained in cardiac and cine modes while the phantom was rotating at 48°/s in the CT scanner. An automated workflow to compute the Jaccard distance (JD) was established to quantify degree of motion artifacts in the reconstructed phantom images. JD values between the cardiac and cine scan modes were compared using a paired sample t-test. In addition, three healthy volunteers were scanned with both modes during a cyclic flexion-extension motion of the knee and analysed using the proposed metric. RESULTS: For all hole sizes and speeds, the cardiac scan mode had significantly lower (p-value <0.001) JD values. (0.39 [0.32-0.46]) i.e less motion artifacts in comparison to the cine mode (0.72 [0.68-0.76]). For both modes, a progressive increase in JD was also observed as the linear speed of the holes increased from 0.75 cm/s to 3.6 cm/s. The dynamic images of the three healthy volunteers showed less artifacts when scanned in cardiac mode compared to cine mode, and this was quantitatively confirmed by the JD values. CONCLUSIONS: A cardiac scan mode could be used to study dynamic musculoskeletal phenomena especially of fast-moving joints since it significantly minimized motion artifacts.

CBCT-based assessment of root canal treatment using micro-CT reference images.

Purpose: This study compared the root canal anatomy between cone-beam computed tomography (CBCT) and micro-computed tomography (micro-CT) images before and after biomechanical preparation and root canal filling. Materials and Methods: Isthmus-containing mesial roots of mandibular molars (n=14) were scanned by micro-CT and 3 CBCT devices: 3D Accuitomo 170 (ACC), NewTom 5G (N5G) and NewTom VGi evo (NEVO). Two calibrated observers evaluated the images for 2-dimensional quantitative parameters, the presence of debris or root perforation, and filling quality in the root canal and isthmus. The kappa coefficient, analysis of variance, and the Tukey test were used for statistical analyses (α=5%). Results: Substantial intra-observer agreement (κ=0.63) was found between micro-CT and ACC, N5G, and NEVO. Debris detection was difficult using ACC (42.9%), N5G (40.0%), and NEVO (40%), with no agreement between micro-CT and ACC, N5G, and NEVO (0.05<κ<0.12). After biomechanical preparation, 2.4%-4.8% of CBCT images showed root perforation that was absent on micro-CT. The 2D parameters showed satisfactory reproducibility between micro-CT and ACC, N5G, and NEVO (intraclass correlation coefficient: 0.60-0.73). Partially filled isthmuses were observed in 2.9% of the ACC images, 8.8% of the N5G and NEVO images, and 26.5% of the micro-CT images, with no agreement between micro-CT and ACC, and poor agreement between micro-CT and N5G and NEVO. Excellent agreement was found for area, perimeter, and the major and minor diameters, while the roundness measures were satisfactory. Conclusion: CBCT images aided in isthmus detection and classification, but did not allow their classification after biomechanical preparation and root canal filling.

Pre-procedural planning of coronary revascularization by cardiac computed tomography: An expert consensus document of the Society of Cardiovascular Computed Tomography.

Coronary CT angiography (CCTA) demonstrated high diagnostic accuracy for detecting coronary artery disease (CAD) and a key role in the management of patients with low-to-intermediate pretest likelihood of CAD. However, the clinical information provided by this noninvasive method is still regarded insufficient in patients with diffuse and complex CAD and for planning percutaneous coronary intervention (PCI) and surgical revascularization procedures. On the other hand, technology advancements have recently shown to improve CCTA diagnostic accuracy in patients with diffuse and calcific stenoses. Moreover, stress CT myocardial perfusion imaging (CT-MPI) and fractional flow reserve derived from CCTA (CT-FFR) have been introduced in clinical practice as new tools for evaluating the functional relevance of coronary stenoses, with the possibility to overcome the main CCTA drawback, i.e. anatomical assessment only. The potential value of CCTA to plan and guide interventional procedures lies in the wide range of information it can provide: a) detailed evaluation of plaque extension, volume and composition; b) prediction of procedural success of CTO PCI using scores derived from CCTA; c) identification of coronary lesions requiring additional techniques (e.g., atherectomy and lithotripsy) to improve stent implantation success by assessing calcium score and calcific plaque distribution; d) assessment of CCTA-derived Syntax Score and Syntax Score II, which allows to select the mode of revascularization (PCI or CABG) in patients with complex and multivessel CAD. The aim of this Consensus Document is to review and discuss the available data supporting the role of CCTA, CT-FFR and stress CT-MPI in the preprocedural and possibly intraprocedural planning and guidance of myocardial revascularization interventions.

Getting the Most out of Spirometry: A Tool to Guide Dry Powder Inhaler Use.

BACKGROUND: Dry powder inhaler (DPI) use requires sufficient peak inspiratory flow over the DPI internal resistance (PIFR). OBJECTIVES: We examined whether spirometric peak inspiratory flow (PIFspiro) could serve to predict PIFR in patients with obstructive lung disease. METHOD: Thirty healthy nonsmokers and 140 stable outpatients (70 COPD, 70 asthma) performed spirometry according to the 2019 ERS/ATS spirometry update, yielding PIFspiro. Using a PIFR measurement device with varying orifices, all subjects' PIFR values were recorded for 5 predefined resistance levels, characterized by 5 orifice cross sections (SR). A test group including all healthy subjects, 30 of the asthma, and 30 of the COPD patients was used to establish the relationship between PIFR and both PIFspiro and SR by multiple regression. A validation group including the remaining 40 asthma and 40 COPD patients, served to verify whether their predicted PIFR value corresponded to the measured PIFR for each resistance level. RESULTS: The asthma (FEV1 = 78 ± 17 [SD] %pred) and COPD (FEV1 = 46 ± 17 [SD] %pred) patients under study had varying airway obstruction. In the test group, PIFR could be predicted by ln[PIFspiro] (p < 0.0001), SR (p < 0.0001), and SR2 (p = 0.006), with an adjusted R2 = 0.71. In the validation group, estimated PIFR did not significantly differ from measured PIFR (p > 0.05 for the 5 resistance levels). CONCLUSIONS: We propose a simple method to predict PIFR for a range of common DPI resistances, based on the device characteristics and on the patient's characteristics reflected in PIFspiro. As such, routine spirometry can serve to estimate a patient's specific PIFR without the need for additional testing.

Pre-procedural planning of coronary revascularization by cardiac computed tomography: An expert consensus document of the Society of Cardiovascular Computed Tomography.

Coronary CT angiography (CCTA) demonstrated high diagnostic accuracy for detecting coronary artery disease (CAD) and a key role in the management of patients with low-to-intermediate pretest likelihood of CAD. However, the clinical information provided by this noninvasive method is still regarded insufficient in patients with diffuse and complex CAD and for planning percutaneous coronary intervention (PCI) and surgical revascularization procedures. On the other hand, technology advancements have recently shown to improve CCTA diagnostic accuracy in patients with diffuse and calcific stenoses. Moreover, stress CT myocardial perfusion imaging (CT-MPI) and fractional flow reserve derived from CCTA (CT-FFR) have been introduced in clinical practice as new tools for evaluating the functional relevance of coronary stenoses, with the possibility to overcome the main CCTA drawback, i.e. anatomical assessment only. The potential value of CCTA to plan and guide interventional procedures lies in the wide range of information it can provide: a) detailed evaluation of plaque extension, volume and composition; b) prediction of procedural success of CTO PCI using scores derived from CCTA; c) identification of coronary lesions requiring additional techniques (e.g., atherectomy and lithotripsy) to improve stent implantation success by assessing calcium score and calcific plaque distribution; d) assessment of CCTA-derived Syntax Score and Syntax Score II, which allows to select the mode of revascularization (PCI or CABG) in patients with complex and multivessel CAD. The aim of this Consensus Document is to review and discuss the available data supporting the role of CCTA, CT-FFR and stress CT-MPI in the preprocedural and possibly intraprocedural planning and guidance of myocardial revascularization interventions.

Digital tomography in the diagnosis of a posterior pneumothorax in the intensive care unit.

Portable chest radiography is a valuable tool in the intensive care unit. However, the supine position causes superposition of anatomical structures resulting in less reliable detection of certain abnormalities. Recently, a portable digital tomosynthesis (pDTS) prototype with a modified motorized X-ray device was developed. We aimed to compare the diagnostic value of pDTS to standard bedside chest radiography in the diagnosis of a posterior pneumothorax. A modified motorized X-ray device was developed to perform 15 radiographic projections while translating the X-ray tube 25 cm (10 cm ramp up and 15 cm during X-ray exposure) with a total radiation dose of 0.54 mSv. This new technique of pDTS was performed in addition to standard bedside chest X-ray in a patient with a confirmed posterior hydropneumothorax. The images were compared with the standard bedside chest X-ray and computed tomography (CT) images by two experienced radiologists. The posterior hydropneumothorax previously identified with CT was visible on tomosynthesis images but not with standard bedside imaging. Combining the digital tomosynthesis technique with the portable X-ray machine could increase the diagnostic value of bedside chest radiography for the diagnosis of posterior pneumothoraces while avoiding intrahospital transport and limiting radiation exposure compared to CT.

An investigation into potential improvements in the design of lead glasses for protecting the eyes of interventional cardiologists.

The lens of the eye can be damaged by ionising radiation, so individuals whose eyes are exposed to radiation during their work may need to protect their eyes from exposure. Lead glasses are widely available, but there are questions about their efficiency in providing eye protection. In this study, Monte Carlo simulations are used to assess the efficiency of lead glasses in protecting the sensitive volume of the eye lens. Two designs currently available for interventional cardiologists are a wraparound (WA) style and ones with flat frontal lenses with side shielding. These designs were considered together with four modifications that would impact upon their efficiency: changing the lead equivalent thickness, adding lead to the frames, elongating the frontal lenses, and adding a closing shield to the bottom rim. For the eye closest to the source, standard models of lead glasses only decrease the radiation reaching the most sensitive region of the eye lens by 22% or less. Varying the lead thickness between 0.4 mm and 0.75 mm had little influence on the protection provided in the simulation of clinical use, neither did adding lead to the frames. Improved shielding was obtained by elongating the frontal lens, which could reduce radiation reaching the eye lens by up to 76%. Glasses with lenses that had a rim at the base, extending towards the face of the user, also provided better shielding than current models, decreasing the dose by up to 80%. In conclusion, elongating the frontal lens of lead glasses, especially of the WA design, could provide a three-fold increase in shielding efficiency and this is still valid for lenses with 0.4 mm lead equivalence.