An overview of automated flow systems for total and isotopic analysis of strontium and yttrium in samples of environmental interest.

Due to the different uses of radioactivity during the last decades, there has been an increase in the concentration of natural and artificial radionuclides in the environment. This, along with some accidents with a high affect public opinion (for example, Chernobyl and Fukushima), have led to the growth and establishment of environmental radioactivity monitoring programs. Currently, trends in legislation and research are focused on the development of accurate, precise, reliable and fast analytical methods with low limits of detection (LOD) for radionuclides determination, such as strontium and yttrium, in environmental samples. In this paper, two comprehensive reviews and four automated analytical systems for total and isotopic determination of yttrium and strontium are presented. The developed methods have been applied in the analysis of environmental samples with low concentrations of these analytes. These methodologies have been automated by exploiting flow analysis techniques, such as multi-syringe flow injection analysis (MSFIA), Sequential injection analysis (SIA) and laboratory-on-valve (LOV) systems, achieving a minimal handling and low consumption of samples and reagents, a significant reduction in waste generation and a high frequency of analysis. In the developed methodologies, some spectrometric methods such as ICP-OES and ICP-MS have been implemented as detection techniques instead of radiometric detectors obtaining a fully automated, low-cost and fast yttrium and strontium determinations.

Synthesis and Application of a New Polymer with Imprinted Ions for the Preconcentration of Uranium in Natural Water Samples and Determination by Digital Imaging.

This work proposes the synthesis of a new polymer with imprinted ions (IIP) for the pre-concentration of uranium in natural waters using digital imaging as a detection technique. The polymer was synthesized using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP) for complex formation, ethylene glycol dimethacrylate (EGDMA) as a crosslinking reagent, methacrylic acid (AMA) as functional monomer, and 2,2'-azobisisobutyronitrile as a radical initiator. The IIP was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy (FTIR). Uranium determination was performed using digital imaging (ID), and some experimental conditions (sample pH, eluent concentration, and sampling flow rate) were optimized using a two-level full factorial design and Doelhert response surface methodology. Thus, using the optimized conditions, the system allowed the determination of uranium with detection and quantification limits of 2.55 and 8.51 µg L-1, respectively, and a pre-concentration factor of 8.2. All parameters were determined using a 25 mL sample volume. The precision expressed as relative deviation (RSD%) was 3.5% for a solution with a concentration of 50 µg L-1. Given this, the proposed method was used for the determination of uranium in four samples of natural waters collected in the city of Caetité, Bahia, Brazil. The concentrations obtained ranged from 35 to 75.4 µg L-1. The accuracy was evaluated by the addition/recovery test, and the values found ranged between 91 and 109%.

Flow-based determination of lead exploiting in-syringe dispersive liquid-liquid micro-extraction in xylene and integrated spectrophotometric detection.

A lab-in-syringe flow system exploiting dispersive liquid-liquid micro-extraction in a solvent lighter than water is proposed for the spectrophotometric determination of lead in industrial residual waters. The steps inherent to both liquid-liquid extraction and monitoring of the formed compound are in-syringe carried out. The classical carbon tetrachloride is not used as the extracting solvent, as it does not present the friendly characteristics inherent to the Green Analytical Chemistry. Aiming at a cleaner alternative for this determination, xylene is selected. Enrichment factor, linear dynamic range, detection limit, sample throughput and residue volume inherent to the proposed procedure were estimated as 36, 50.0-250 µg L-1, 9.0 µg L-1, 13 h-1, and 2.0 mL, respectively.

Selenium inorganic speciation in beers using MSFIA-HG-AFS system after multivariate optimization.

In this work, the use of a multisyringe flow injection analysis coupled to hydride generation atomic fluorescence spectrometry (MSFIA-HG-AFS) for inorganic selenium chemical speciation was proposed. A Doehlert design was applied to optimize the experimental conditions for hydride generation (NaBH4 and HCl concentrations). The limits of quantification (LoQ) obtained were 0.07 µg L-1, for total inorganic Se, and 0.08 µg L-1, for Se(IV). Accuracy and precision of the proposed analytical method were evaluated through analysis of standard reference material and addition and recovery tests. The optimized method was applied to analyses of eight samples of beer, produced in Spain, obtaining concentrations for Se(IV) (<0.08 - 0.46 ± 0.01 µg L-1), total inorganic Se (0.47 ± 0.01 - 3.04 ± 0.62 µg L-1) and Se(VI) (0.06 ± 0.01 - 3.00 ± 0.59 µg L-1). The proposed analytical method was accurate, precise and sensitivity for determination of selenium species in beer samples.

Determination of total and bioavailable As and Sb in children's paints using the MSFIA system coupled to HG-AFS.

In this study, the use of hydride generation atomic fluorescence spectrometry (HG-AFS) coupled with the multi-syringe flow injection analysis (MSFIA) has been proposed in the application of the Doehlert design to optimise the determination of As and Sb in gouache and tempera children's paints. The determination of the total and bioavailable As and Sb in paint samples from various brands and colours was also investigated. The limits of quantification (LOQ) obtained for the determination of As and Sb were 14.0 and 8.6 ng g-1, respectively. The accuracy and precision of the method were evaluated through recovery tests (by the analyte addition method) at three levels for both elements, and by the analysis of certified reference materials of clay (CRM 052, Loamy Clay 1) and river water (SLRS-4). Twenty paint samples, manufactured in China, Italy, Spain and Brazil, were analysed. The concentrations of As varied between below LOQ (<14 ng g-1) and 136.0 ± 1.1 ng g-1 (average value of 101.0 ng g-1, n = 10), and Sb between below LOQ (<8.6 ng g-1) and 74.0 ± 5.4 ng g-1 (average value of 21.7 ng g-1, n = 17). The children's paint samples presented As and Sb concentrations that were below the maximum values established by the National Institute of Metrology, Quality and Technology (INMETRO), as well as by the European legislation Directive 2009/48/EC. Based on the obtained results for the total As and Sb concentrations, eight samples were selected to evaluate the migration or bioavailability of As and Sb after solubilisation in HCl solution. The obtained results showed that for the eight analysed samples, the concentration of both elements after solubilisation in HCl solution were below the LOQ (<16.2 ng g-1 for As and <7.1 ng g-1 for Sb). These values correspond to the limits of analytical concentrations of As and Sb established by INMETRO and the Brazilian Association of Technical Standards (ABNT). The determined concentrations of As and Sb guarantee the safety (with regards to these elements) for children when using the analysed paint samples since they do not cause any health risk. The analytical method for the determination of the total and bioavailable As and Sb in children's paints was efficient, accurate and precise.

Fast-response flow-based method for evaluating 131I from biological and hospital waste samples exploiting liquid scintillation detection.

This paper presents a fast and automatic flow-based method to extract 131I from biological samples and hospital waste, previous to liquid scintillation detection. 131I is a radionuclide extensively used in Nuclear Medicine due to their beta and gamma disintegrations, whereby hospitals have to manage the associated waste generation. The automatic developed system is based on Lab-On-Valve (LOV) flow-technique exploiting Cl-resin (135 mg per extraction). This methodology allows performing sample extractions and measurements on the same day, since the extraction frequency takes 1.4-4 h-1, depending on the analysed sample volume, plus up to 2 h of measurement for each vial. 131I is retained as iodine ion and eluted with sodium sulphide 0.2 mol L-1. The maximum sample volume that can be preconcentrated is 20 mL, reaching an extraction efficiency of 85 ±â€¯5%. The minimum detectable activity (MDA) is 0.05 Bq, showing a precision of 7% RSD (n = 5). Both, biological samples (urine and saliva) and hospital waste samples can be satisfactorily analysed by the proposed system, obtaining recoveries between 90 and 110%. The developed method is then suitable to implement in hospitals, improving the surveillance of the 131I environmental release.

Direct photoimmobilization of extraction disks on "green state" 3D printed devices.

Post-curing is essential to improve the mechanical properties of 3D printed parts fabricated by stereolithography (SLA), since right after 3D printing they remain in a "green state". It means that the 3D printed parts have reached their final shape, but the polymerization reaction has not been yet completed. Herein, we take advantage of the tacky partially polymerized surface of "green state" SLA 3D printed parts to immobilize extraction disks and miniature magnets, which after UV post-curing, become permanently attached to the 3D printed part resulting in a rotating-disk sorptive extraction device (RDSE). The developed "stick & cure" procedure is reagent-free and does not require any additional preparation time, specialized skills, or instrumentation. As proof of concept, 3D printed RDSE devices with immobilized chelating disks have been applied to the simultaneous extraction of 14 trace metals prior to ICP-OES determination, featuring LODs between 0.03 and 1.27 µg L-1, and an excellent device-to-device reproducibility (n = 5, RSD = 2.7-8.3%). The developed method was validated using certified wastewater and soil reference samples, and satisfactory spiking recoveries were obtained in the analysis of highly polluted solid waste treatment plant leachates (89-110%). In addition, exploiting the versatility of 3D printing, nine RDSE devices with different shapes were fabricated. Their performance was evaluated and compared for the fast extraction of the highly toxic Cr (VI) as its 1,5-diphenylcarbazide complex in reversed-phase mode, showing different extraction performance on depending on the shape of the 3D printed RDSE device.

Automated dispersive liquid-liquid microextraction based on the solidification of the organic phase.

In this work, the dispersive liquid-liquid microextraction technique based on the solidification of the organic phase (DLLME-SFO) has been automated for the first time. DLLME-SFO is automated by hyphenating a sequential injection analysis (SIA) system with a custom-made robotic phase separator. Automated in-syringe DLLME is followed by phase separation in a 3D printed device integrating a Peltier cell set, mounted on a multi-axis robotic arm. The combined action of the flow system and the robotic arm is controlled by a single software package, enabling the solidification/melting and collection of the organic phase for further analyte quantification. As proof-of-concept, automated DLLME-SFO was applied to the extraction of parabens followed by separation using liquid chromatography, obtaining LODs between 0.3 and 1.3 µg L-1 (4 mL of sample extracted in 1 mL of 1-dodecanol: MeOH, 15:85, v-v). The method showed a high reproducibility, obtaining intraday RSDs between 4.6% and 5.8% (n = 6), and interday RSDs between 5.6% and 8.6% (n = 6). The developed method was evaluated for the determination of parabens in water, urine, saliva, and personal care products.

3D printed device for the automated preconcentration and determination of chromium (VI).

A 3D printed device for the fully automated disk-based solid-phase extraction (SPE) of Cr (VI) from water samples has been fabricated. The compatibility of the use of organic solvents for analyte elution with 3D printed flow devices based on polymers fabricated using stereolithograph​y has been evaluated. The developed methodology comprises the complexation of Cr (VI) with 1, 5-diphenylcarbazide (DPC) in acidic medium and the subsequent retention of the complex in a SBD-RPS disk contained within the 3D printed device. A multisyringe flow injection analysis system with online spectrophotometric detection has been used for the automation of the method. The fabricated 3D printed device integrates the different components of the flow analysis manifold, including connectors and mixers, being a powerful approach towards the reproducible construction of highly integrated flow-based manifolds. The extracted Cr (VI)-DPC complex is eluted with a mixture of methanol- sulfuric acid and quantified at 540 nm. The effect on the analytical signal and the optimization of variables were evaluated using multivariate and univariate techniques. A detection limit of 1 ng Cr (VI) and a linear working range of 3.2-600 ng Cr (VI) were obtained using a sample volume of 2 ml. The intra-day and inter-day RSDs were 4.8% (10 µg L-1, n = 12) and 3.4% (n = 5, different day with a different disk), respectively. The applicability of the fabricated 3D printed device has been proved by the determination of Cr (VI) in groundwater, surface water and leachates.

3D printed device including disk-based solid-phase extraction for the automated speciation of iron using the multisyringe flow injection analysis technique.

The development of advanced manufacturing techniques is crucial for the design of novel analytical tools with unprecedented features. Advanced manufacturing, also known as 3D printing, has been explored for the first time to fabricate modular devices with integrated features for disk-based automated solid-phase extraction (SPE). A modular device integrating analyte oxidation, disk-based SPE and analyte complexation has been fabricated using stereolithographic 3D printing. The 3D printed device is directly connected to flow-based analytical instrumentation, replacing typical flow networks based on discrete elements. As proof of concept, the 3D printed device was implemented in a multisyringe flow injection analysis (MSFIA) system, and applied to the fully automated speciation, SPE and spectrophotometric quantification of Fe in water samples. The obtained limit of detection for total Fe determination was 7ng, with a dynamic linear range from 22ng to 2400ng Fe (3mL sample). An intra-day RSD of 4% (n = 12) and an inter-day RSD of 4.3% (n = 5, 3mL sample, different day with a different disk), were obtained. Incorporation of integrated 3D printed devices with automated flow-based techniques showed improved sensitivity (85% increase on the measured peak height for the determination of total Fe) in comparison with analogous flow manifolds built from conventional tubing and connectors. Our work represents a step forward towards the improved reproducibility in the fabrication of manifolds for flow-based automated methods of analysis, which is especially relevant in the implementation of interlaboratory analysis.

On line automated system for the determination of Sb(V), Sb(III), thrimethyl antimony(v) and total antimony in soil employing multisyringe flow injection analysis coupled to HG-AFS.

This paper proposes the use of a multisyringe flow injection analysis (MSFIA) system for inorganic antimony speciation analysis, trimethyl antimony(V) and determination of total antimony in soil samples using hydride generation atomic fluorescence spectrometry (HG-AFS). Total antimony has been determined after reduction of antimony(V) to antimony(III) using potassium iodide and ascorbic acid. For determination of total inorganic antimony the sample is percolated in a mini-column containing the Dowex 50W-X8 resin for retention of the organic species of antimony. Antimony(III) is quantified in presence of 8-hydroxyquinoline as masking agent for antimony(V) after an extraction step of the organic antimony species using the also same mini-column. The trimethyl antimony(V) content is found by difference between total antimony and total inorganic antimony. By other hand, antimony(V) is quantified by difference between total inorganic antimony and antimony(III). The analytical determinations were performed using sodium tetrahydroborate as reducing agent. The optimization step was performed using two-level full factorial design and Doehlert matrix involving the factors: hydrochloric acid and sodium tetrahydroborate concentrations and sample flow rate. The optimized experimental conditions allow the antimony determination utilizing the external calibration technique with limits of detection and quantification of 0.9 and 3.1ngg-1, respectively, and a precision expressed as relative standard deviation of 3.2% for an antimony solution of 5.0µgL-1. The method accuracy was confirmed by analysis of the soil certified reference material furnished from Sigma-Aldrich RTC. Additionally, addition/recovery tests were performed employing synthetic solutions prepared using trimethyl antimony(V), antimony(III), antimony(V) and five soil samples. The antimony extraction step was performed in a closed system using hydrochloric acid, ultrasonic radiation and controlled temperature. The method proposed was applied for analysis of thirteen soil samples collected in different sites of the Balearic Islands, Spain, and the results obtained varied from 19 to 46ngg-1 for trimethyl antimony(V) and from 113 to 215ngg-1 for total inorganic antimony. The concentrations obtained to antimony(V) were always higher than for antimony(III) in all the analyzed samples.

Development of a MSFIA system for sequential determination of antimony, arsenic and selenium using hydride generation atomic fluorescence spectrometry.

This paper proposed a multisyringe flow injection analysis (MSFIA) system for antimony, arsenic and selenium determination in peanut samples by hydride generation atomic fluorescence spectrometry (HG-AFS). The optimization step of the hydride generation was performed using a two-level full factorial design involving the parameters: hydrochloric acid, sodium tetrahydroborate and potassium iodide concentrations. So, using the chemical conditions optimized, this method allows the determination of these elements employing the external calibration technique using aqueous standards with limits of detection and quantification of 0.04 and 0.14µgL(-1) for antimony, 0.04 and 0.14µgL(-1) for arsenic and 0.14 and 0.37µgL(-1) for selenium, respectively. Additionally, the effect of vanadium, chromium, cobalt, nickel, zinc, copper, iron and molybdenum on the generation of chemical vapour was also studied. The precision expressed as relative standard deviation varied from 1.2 to 3.6% for antimony, 1.8-3.9% for arsenic and 1.8-2% for selenium. The accuracy for arsenic and selenium was confirmed using the certified peach leaves reference material SRM 1547 produced by National Institute of Standard and Technology. The proposed method showed 45 injection throughput (h(-1)) using 1.6mL sample volume for each element, 0.8mL NaBH4 0.5% (w/v) containing NaOH 0.05% (w/v), 0.8mL HCl 5M and 0.4mL KI 14% (w/v) containing L-ascorbic acid 2.5% (w/v). The method was applied to the determination of antimony, arsenic and selenium in peanut samples, which were firstly lyophilized and afterward digested using microwave assisted radiation. Six samples were analyzed and the contents of the elements found were: 28.7-41.3µgkg(-1) for arsenic, 86.4-480.1µgkg(-1) for selenium and 32.6-52.4µgkg(-1) for antimony. Addition/recovery tests were also performed to confirm the method accuracy for the three elements.

Masking Agents Evaluation for Lead Determination by Flow Injection-Hydride Generation-Atomic Fluorescence Spectrometry Technique: Effect of KI, L-Cysteine, and 1,10-Phenanthroline.

Hydride generation (HG) of lead technique presents interferences from foreign ions of complex matrix samples. In order to minimize these interferences, the effect of masking agents such as KI, L-cysteine, and 1,10-phenanthroline was studied in the absence and in the presence of selected interfering species (As, Cr, Cu, and Fe). Different modes of addition of masking agents were accomplished, that is, to either sample or KBH4 reducing solution. The lead determinations were performed using a flow injection analysis (FIA) system coupled to HG and atomic fluorescence spectrometry (AFS). The linearity of calibration curves (1-10 µg Pb L(-1)) was not affected by the addition of the masking agents. The use of KI in the reducing solution diminished interferences from concentrations of As and Cu, while 1,10-phenanthroline showed a positive effect on the interference by As. Moreover, Cr and Cu appeared to be the most serious interfering ions for plumbane (PbH4), because they drastically reduced the analytical signal of lead. Fe did not present any interference under the employed experimental conditions, even at high levels. The accuracy was established through the analysis of certified reference material (i.e., BCR-610, groundwater) using KI as masking agent. The detection limit reached by FIA-HG-AFS proposed methodology was 0.03 µg Pb L(-1).

MSFIA-LOV system for (226)Ra isolation and pre-concentration from water samples previous radiometric detection.

An automatic system based on multisyringe flow injection analysis (MSFIA) and lab-on-valve (LOV) flow techniques for separation and pre-concentration of (226)Ra from drinking and natural water samples has been developed. The analytical protocol combines two different procedures: the Ra adsorption on MnO2 and the BaSO4 co-precipitation, achieving more selectivity especially in water samples with low radium levels. Radium is adsorbed on MnO2 deposited on macroporous of bead cellulose. Then, it is eluted with hydroxylamine to transform insoluble MnO2 to soluble Mn(II) thus freeing Ra, which is then coprecipitated with BaSO4. The (226)Ra can be directly detected in off-line mode using a low background proportional counter (LBPC) or through a liquid scintillation counter (LSC), after performing an on-line coprecipitate dissolution. Thus, the versatility of the proposed system allows the selection of the radiometric detection technique depending on the detector availability or the required response efficiency (sample number vs. response time and limit of detection). The MSFIA-LOV system improves the precision (1.7% RSD), and the extraction frequency (up to 3 h(-1)). Besides, it has been satisfactorily applied to different types of water matrices (tap, mineral, well and sea water). The (226)Ra minimum detectable activities (LSC: 0.004 Bq L(-1); LBPC: 0.02 Bq L(-1)) attained by this system allow to reach the guidance values proposed by the relevant international agencies e.g. WHO, EPA and EC.

On-line lab-in-syringe cloud point extraction for the spectrophotometric determination of antimony.

Most of the procedures for antimony determination require time-consuming sample preparation (e.g. liquid-liquid extraction with organic solvents), which are harmful to the environment. Because of the high antimony toxicity, a rapid, sensitive and greener procedure for its determination becomes necessary. The goal of this work was to develop an analytical procedure exploiting for the first time the cloud point extraction on a lab-in-syringe flow system aiming at the spectrophotometric determination of antimony. The procedure was based on formation of an ion-pair between the antimony-iodide complex and H(+) followed by extraction with Triton X-114. The factorial design showed that the concentrations of ascorbic acid, H2SO4 and Triton X-114, as well as second and third order interactions were significant at the 95% confidence level. A Box-Behnken design was applied to obtain the response surfaces and to identify the critical values. System is robust at the 95% confidence level. A linear response was observed from 5 to 50 µg L(-1), described by the equation A=0.137+0.050C(Sb) (r=0.998). The detection limit (99.7% confidence level), the coefficient of variation (n=5; 15 µg L(-1)) and the sampling rate was estimated at 1.8 µg L(-1), 1.6% and 16 h(-1), respectively. The procedure allows quantification of antimony in the concentrations established by environmental legislation (6 µg L(-1)) and it was successfully applied to the determination of antimony in freshwater samples and antileishmanial drugs, yielding results in agreement with those obtained by HGFAAS at the 95% confidence level.

Automation of 99Tc extraction by LOV prior ICP-MS detection: application to environmental samples.

A new, fast, automated and inexpensive sample pre-treatment method for (99)Tc determination by inductively coupled plasma-mass spectrometry (ICP-MS) detection is presented. The miniaturized approach is based on a lab-on-valve (LOV) system, allowing automatic separation and preconcentration of (99)Tc. Selectivity is provided by the solid phase extraction system used (TEVA resin) which retains selectively pertechnetate ion in diluted nitric acid solution. The proposed system has some advantages such as minimization of sample handling, reduction of reagents volume, improvement of intermediate precision and sample throughput, offering a significant decrease of both time and cost per analysis in comparison to other flow techniques and batch methods. The proposed LOV system has been successfully applied to different samples of environmental interest (water and soil) with satisfactory recoveries, between 94% and 98%. The detection limit (LOD) of the developed method is 0.005 ng. The high durability of the resin and its low amount (32 mg), its good intermediate precision (RSD 3.8%) and repeatability (RSD 2%) and its high extraction frequency (up to 5 h(-1)) makes this method an inexpensive, high precision and fast tool for monitoring (99)Tc in environmental samples.

On-line monitoring of the photocatalytic degradation of 2,4-D and dicamba using a solid-phase extraction-multisyringe flow injection system.

A fully automated on-line system for monitoring the photocatalytic degradation of herbicides was developed using multisyringe flow injection analysis (MSFIA) coupled to a solid phase extraction (SPE) unit with UV detection. The calibration curves were linear in the concentration range of 100-1000 µg L(-1) for 3,6-dichloro-2-methoxybenzoic acid (dicamba) and 500-3000 µg L(-1) for 2,4-dichlorophenoxyacetic acid (2,4-D), while the detection limits were 30 and 135 µg L(-1) for dicamba and 2,4-D, respectively. The monitoring of the photocatalytic degradation (TiO2 anatase/UV 254 nm) of these two herbicides was performed by MSFIA-SPE system using a small sample volume (2 mL) in a fully automated approach. The degradation was assessed in ultrapure and drinking water with initial concentrations of 1000 and 2000 µg L(-1) for dicamba and 2,4-D, respectively. Degradation percentages of approximately 85% were obtained for both herbicides in ultrapure water after 45 min of photocatalytic treatment. A similar degradation efficiency in drinking water was observed for 2,4-D, whereas dicamba exhibited a lower degradation percentage (75%), which could be attributed to the presence of inorganic species in this kind of water.

Automated method for simultaneous lead and strontium isotopic analysis applied to rainwater samples and airborne particulate filters (PM10).

A new automated, sensitive, and fast system for the simultaneous online isolation and preconcentration of lead and strontium by sorption on a microcolumn packed with Sr-resin using an inductively coupled plasma mass spectrometry (ICP-MS) detector was developed, hyphenating lab-on-valve (LOV) and multisyringe flow injection analysis (MSFIA). Pb and Sr are directly retained on the sorbent column and eluted with a solution of 0.05 mol L(-1) ammonium oxalate. The detection limits achieved were 0.04 ng for lead and 0.03 ng for strontium. Mass calibration curves were used since the proposed system allows the use of different sample volumes for preconcentration. Mass linear working ranges were between 0.13 and 50 ng and 0.1 and 50 ng for lead and strontium, respectively. The repeatability of the method, expressed as RSD, was 2.1% and 2.7% for Pb and Sr, respectively. Environmental samples such as rainwater and airborne particulate (PM10) filters as well as a certified reference material SLRS-4 (river water) were satisfactorily analyzed obtaining recoveries between 90 and 110% for both elements. The main features of the LOV-MSFIA-ICP-MS system proposed are the capability to renew solid phase extraction at will in a fully automated way, the remarkable stability of the column which can be reused up to 160 times, and the potential to perform isotopic analysis.

Automated total and radioactive strontium separation and preconcentration in samples of environmental interest exploiting a lab-on-valve system.

A novel lab-on-valve system has been developed for strontium determination in environmental samples. Miniaturized lab-on-valve system potentially offers facilities to allow any kind of chemical and physical processes, including fluidic and microcarrier bead control, homogenous reaction and liquid-solid interaction. A rapid, inexpensive and fully automated method for the separation and preconcentration of total and radioactive strontium, using a solid phase extraction material (Sr-Resin), has been developed. Total strontium concentrations are determined by ICP-OES and (90)Sr activities by a low background proportional counter. The method has been successfully applied to different water samples of environmental interest. The proposed system offers minimization of sample handling, drastic reduction of reagent volume, improvement of the reproducibility and sample throughput and attains a significant decrease of both time and cost per analysis. The LLD of the total Sr reached is 1.8ng and the minimum detectable activity for (90)Sr is 0.008Bq. The repeatability of the separation procedure is 1.2% (n=10).

Multi-syringe chromatography (MSC) system for the on-line solid-phase extraction and determination of hydrochlorothiazide and losartan potassium in superficial water, groundwater and wastewater outlet samples.

In this paper, a combination of multi-syringe chromatography analysis technique with extraction disks sorbents for the pre-concentration and determination of hydrochlorothiazide and losartan potassium in superficial water, groundwater and wastewater outlet samples has been developed. The system developed was proved for the determination of hydrochlorothiazide and losartan potassium in spiked water samples with recoveries ranging from 95 to 118%. The method involves the on-line enrichment of the targeted analytes from spiked water samples onto a Cation-SR sorbent material. The analytes are subsequently eluted and transported to the monolithic column, Chromolith Flash RP-18e column (25 mmx4.6 mm i.d.). The mobile phase used was 10 mM potassium dihydrogen phosphate (pH 3.0):acetonitrile:methanol (60:30:10 v/v/v), flow-rate 0.8 mL min(-1). UV detection is carried out at 226 nm. Under the optimized chemical and physical variables, the detection limit for hydrochlorothiazide and losartan potassium calculated as 3Syx/b was 0.07 and 0.09 mgL(-1), respectively, for a sample loading volume of 1.0 mL.