Opto Field-Effect Transistors for Detecting Quercetin-Cu2+ Complex.

In this study, we explored the potential of applying biosensors based on silicon nanowire field-effect transistors (bio-NWFETs) as molecular absorption sensors. Using quercetin and Copper (Cu2+) ion as an example, we demonstrated the use of an opto-FET approach for the detection of molecular interactions. We found that photons with wavelengths of 450 nm were absorbed by the molecular complex, with the absorbance level depending on the Cu2+ concentration. Quantitative detection of the molecular absorption of metal complexes was performed for Cu2+ concentrations ranging between 0.1 µM and 100 µM, in which the photon response increased linearly with the copper concentration under optimized bias parameters. Our opto-FET approach showed an improved absorbance compared with that of a commercial ultraviolet-visible spectrophotometry.

Fabry-Perot interferometric calibration of van der Waals material-based nanomechanical resonators.

One of the challenges in integrating nanomechanical resonators made from van der Waals materials in optoelectromechanical technologies is characterizing their dynamic properties from vibrational displacement. Multiple calibration schemes using optical interferometry have tackled this challenge. However, these techniques are limited only to optically thin resonators with an optimal vacuum gap height and substrate for interferometric detection. Here, we address this limitation by implementing a modeling-based approach via multilayer thin-film interference for in situ, non-invasive determination of the resonator thickness, gap height, and motional amplitude. This method is demonstrated on niobium diselenide drumheads that are electromotively driven in their linear regime of motion. The laser scanning confocal configuration enables a resolution of hundreds of picometers in motional amplitude for circular and elliptical devices. The measured thickness and spacer height, determined to be in the order of tens and hundreds of nanometers, respectively, are in excellent agreement with profilometric measurements. Moreover, the transduction factor estimated from our method agrees with the result of other studies that resolved Brownian motion. This characterization method, which applies to both flexural and acoustic wave nanomechanical resonators, is robust because of its scalability to thickness and gap height, and any form of reflecting substrate.

Photothermal Responsivity of van der Waals Material-Based Nanomechanical Resonators.

Nanomechanical resonators made from van der Waals materials (vdW NMRs) provide a new tool for sensing absorbed laser power. The photothermal response of vdW NMRs, quantified from the resonant frequency shifts induced by optical absorption, is enhanced when incorporated in a Fabry-Pérot (FP) interferometer. Along with the enhancement comes the dependence of the photothermal response on NMR displacement, which lacks investigation. Here, we address the knowledge gap by studying electromotively driven niobium diselenide drumheads fabricated on highly reflective substrates. We use a FP-mediated absorptive heating model to explain the measured variations of the photothermal response. The model predicts a higher magnitude and tuning range of photothermal responses on few-layer and monolayer NbSe2 drumheads, which outperform other clamped vdW drum-type NMRs at a laser wavelength of 532 nm. Further analysis of the model shows that both the magnitude and tuning range of NbSe2 drumheads scale with thickness, establishing a displacement-based framework for building bolometers using FP-mediated vdW NMRs.

Correlation between the optical absorption and twisted angle of bilayer graphene observed by high-resolution reflectance confocal laser microscopy.

We report a systematic study of the optical absorption of twisted bilayer graphene (tBLG) across a large range of twist angles from 0° to 30° using a high-resolution reflectance confocal laser microscopy (RCLM) system. The high-quality single crystalline tBLG was synthesized via the efficient plasma enhanced chemical vapor deposition techniques without the need of active heating. The sensitivity of acquired images from the RCLM were better than conventional optical microscopes. Although the highest spatial resolution of RCLM is still lower than scanning electron microscopes, it possesses the advantages of beam-damage and vacuum free. Moreover, the high intensity-resolution (sensitivity) images firstly allowed us to distinguish the slight absorption differences and analyze the correlation between the optical absorption and twisted angle of tBLG after data processing procedures. A maximum absorption (minimum transmission) was observed at the stacking angle of tBLG from 10° to 20°, indicating the interplay between the laser and the electron/hole van-Hove singularities when tBLG oriented around the critical angle (θc∼13°). The twisted angle correlated optical absorption paves an alternative way not only to visibly identify the interlayer orientation of tBLG but also to reflect the characterization of the interlayer coupling via its band structure.

Imaging Off-Resonance Nanomechanical Motion as Modal Superposition.

Observation of resonance modes is the most straightforward way of studying mechanical oscillations because these modes have maximum response to stimuli. However, a deeper understanding of mechanical motion can be obtained by also looking at modal responses at frequencies in between resonances. Here, an imaging of the modal responses for a nanomechanical drum driven off resonance is presented. By using the frequency modal analysis, these shapes are described as a superposition of resonance modes. It is found that the spatial distribution of the oscillating component of the driving force, which is affected by both the shape of the actuating electrode and inherent device properties such as asymmetry and initial slack, greatly influences the modal weight or participation. This modal superposition analysis elucidates the dynamics of any nanomechanical system through modal weights. This aids in optimizing mode-specific designs for force sensing and integration with other systems.

Ultralow Schottky Barriers in Hexagonal Boron Nitride-Encapsulated Monolayer WSe2 Tunnel Field-Effect Transistors.

To explore the potential of field-effect transistors (FETs) based on monolayers (MLs) of the two-dimensional semiconducting channel (SC) for spintronics, the two most important issues are to ensure the formation of variable low-resistive tunnel ferromagnetic contacts (FCs) and to preserve intrinsic properties of the SC during fabrication. Large Schottky barriers lead to the formation of high resistive contacts, and methods adopted to control the barriers often alter the intrinsic properties of the SC. This work aims at addressing both issues in fully encapsulated ML WSe2 FETs using bilayer hexagonal boron nitride (h-BN) as a tunnel barrier at the FC/SC interface. We investigate the electrical transport in ML WSe2 FETs with the current-in-plane geometry that yields hole mobilities of ∼38.3 cm2 V-1 s-1 at 240 K and on/off ratios of the order of 107, limited by the contact regions. We have achieved an ultralow effective Schottky barrier (∼5.34 meV) with an encapsulated tunneling device as opposed to a nonencapsulated device in which the barrier heights are considerably higher. These observations provide an insight into the electrical behavior of the FC/h-BN/SC/h-BN heterostructures, and such control over the barrier heights opens up the possibilities for WSe2-based spintronic devices.

Observation of Wigner crystal phase and ripplon-limited mobility behavior in monolayer CVD MoS2 with grain boundary.

Two-dimensional electron gas (2DEG) is crucial in condensed matter physics and is present on the surface of liquid helium and at the interface of semiconductors. Monolayer MoS2 of 2D materials also contains 2DEG in an atomic layer as a field effect transistor (FET) ultrathin channel. In this study, we synthesized double triangular MoS2 through a chemical vapor deposition method to obtain grain boundaries for forming a ripple structure in the FET channel. When the temperature was higher than approximately 175 K, the temperature dependence of the electron mobility µ was consistent with those in previous experiments and theoretical predictions. When the temperature was lower than approximately 175 K, the mobility behavior decreased with the temperature; this finding was also consistent with that of the previous experiments. We are the first research group to explain the decreasing mobility behavior by using the Wigner crystal phase and to discover the temperature independence of ripplon-limited mobility behavior at lower temperatures. Although these mobility behaviors have been studied on the surface of liquid helium through theories and experiments, they have not been previously analyzed in 2D materials and semiconductors. We are the first research group to report the similar temperature-dependent mobility behavior of the surface of liquid helium and the monolayer MoS2.

Quadratic Characteristics of Environment Induced Voltage Shot Noise in Josephson Junctions.

We investigate theoretically and experimentally the environment-induced voltage shot noise in current biased Josephson junctions induced by phase particle tunneling. Quantum mechanical treatment based on the Caldeira-Leggett model with tight-binding formulation in local Wannier bases gives a clear picture of the voltage shot noise. A universal form of the zero-frequency noise spectrum is obtained, which exhibits a quadratic dependence on the mean voltage in small bias region. The quadratic dependence is verified experimentally on junctions covering a wide range of parameters, and is found also in junction arrays of various array sizes.

Detection of electrically neutral and nonpolar molecules in ionic solutions using silicon nanowires.

We report on a technique that can extend the use of nanowire sensors to the detection of interactions involving nonpolar and neutral molecules in an ionic solution environment. This technique makes use of the fact that molecular interactions result in a change in the permittivity of the molecules involved. For the interactions taking place at the surface of nanowires, this permittivity change can be determined from the analysis of the measured complex impedance of the nanowire. To demonstrate this technique, histidine was detected using different charge polarities controlled by the pH value of the solution. This included the detection of electrically neutral histidine at a sensitivity of 1 pM. Furthermore, it is shown that nonpolar molecules, such as hexane, can also be detected. The technique is applicable to the use of nanowires with and without a surface-insulating oxide. We show that information about the changes in amplitude and the phase of the complex impedance reveals the fundamental characteristics of the molecular interactions, including the molecular field and the permittivity.

Isolation and Identification of Post-Transcriptional Gene Silencing-Related Micro-RNAs by Functionalized Silicon Nanowire Field-effect Transistor.

Many transcribed RNAs are non-coding RNAs, including microRNAs (miRNAs), which bind to complementary sequences on messenger RNAs to regulate the translation efficacy. Therefore, identifying the miRNAs expressed in cells/organisms aids in understanding genetic control in cells/organisms. In this report, we determined the binding of oligonucleotides to a receptor-modified silicon nanowire field-effect transistor (SiNW-FET) by monitoring the changes in conductance of the SiNW-FET. We first modified a SiNW-FET with a DNA probe to directly and selectively detect the complementary miRNA in cell lysates. This SiNW-FET device has 7-fold higher sensitivity than reverse transcription-quantitative polymerase chain reaction in detecting the corresponding miRNA. Next, we anchored viral p19 proteins, which bind the double-strand small RNAs (ds-sRNAs), on the SiNW-FET. By perfusing the device with synthesized ds-sRNAs of different pairing statuses, the dissociation constants revealed that the nucleotides at the 3'-overhangs and pairings at the terminus are important for the interactions. After perfusing the total RNA mixture extracted from Nicotiana benthamiana across the device, this device could enrich the ds-sRNAs for sequence analysis. Finally, this bionanoelectronic SiNW-FET, which is able to isolate and identify the interacting protein-RNA, adds an additional tool in genomic technology for the future study of direct biomolecular interactions.

High-Current Gain Two-Dimensional MoS2-Base Hot-Electron Transistors.

The vertical transport of nonequilibrium charge carriers through semiconductor heterostructures has led to milestones in electronics with the development of the hot-electron transistor. Recently, significant advances have been made with atomically sharp heterostructures implementing various two-dimensional materials. Although graphene-base hot-electron transistors show great promise for electronic switching at high frequencies, they are limited by their low current gain. Here we show that, by choosing MoS2 and HfO2 for the filter barrier interface and using a noncrystalline semiconductor such as ITO for the collector, we can achieve an unprecedentedly high-current gain (α ∼ 0.95) in our hot-electron transistors operating at room temperature. Furthermore, the current gain can be tuned over 2 orders of magnitude with the collector-base voltage albeit this feature currently presents a drawback in the transistor performance metrics such as poor output resistance and poor intrinsic voltage gain. We anticipate our transistors will pave the way toward the realization of novel flexible 2D material-based high-density, low-energy, and high-frequency hot-carrier electronic applications.

Probing Spin Accumulation induced Magnetocapacitance in a Single Electron Transistor.

The interplay between spin and charge in solids is currently among the most discussed topics in condensed matter physics. Such interplay gives rise to magneto-electric coupling, which in the case of solids was named magneto-electric effect, as predicted by Curie on the basis of symmetry considerations. This effect enables the manipulation of magnetization using electrical field or, conversely, the manipulation of electrical polarization by magnetic field. The latter is known as the magnetocapacitance effect. Here, we show that non-equilibrium spin accumulation can induce tunnel magnetocapacitance through the formation of a tiny charge dipole. This dipole can effectively give rise to an additional serial capacitance, which represents an extra charging energy that the tunneling electrons would encounter. In the sequential tunneling regime, this extra energy can be understood as the energy required for a single spin to flip. A ferromagnetic single-electron-transistor with tunable magnetic configuration is utilized to demonstrate the proposed mechanism. It is found that the extra threshold energy is experienced only by electrons entering the islands, bringing about asymmetry in the measured Coulomb diamond. This asymmetry is an unambiguous evidence of spin accumulation induced tunnel magnetocapacitance, and the measured magnetocapacitance value is as high as 40%.

Piezoelectric effect in chemical vapour deposition-grown atomic-monolayer triangular molybdenum disulfide piezotronics.

High-performance piezoelectricity in monolayer semiconducting transition metal dichalcogenides is highly desirable for the development of nanosensors, piezotronics and photo-piezotransistors. Here we report the experimental study of the theoretically predicted piezoelectric effect in triangle monolayer MoS2 devices under isotropic mechanical deformation. The experimental observation indicates that the conductivity of MoS2 devices can be actively modulated by the piezoelectric charge polarization-induced built-in electric field under strain variation. These polarization charges alter the Schottky barrier height on both contacts, resulting in a barrier height increase with increasing compressive strain and decrease with increasing tensile strain. The underlying mechanism of strain-induced in-plane charge polarization is proposed and discussed using energy band diagrams. In addition, a new type of MoS2 strain/force sensor built using a monolayer MoS2 triangle is also demonstrated. Our results provide evidence for strain-gating monolayer MoS2 piezotronics, a promising avenue for achieving augmented functionalities in next-generation electronic and mechanical-electronic nanodevices.

Effect of focused ion beam deposition induced contamination on the transport properties of nano devices.

Focused ion beam (FIB) deposition produces unwanted particle contamination beyond the deposition point. This is due to the FIB having a Gaussian distribution. This work investigates the spatial extent of this contamination and its influence on the electrical properties of nano-electronic devices. A correlation study is performed on carbon-nanotube (CNT) devices manufactured using FIB deposition. The devices are observed using transmission electron microscopy (TEM) and these images are correlated with device electrical characteristics. To discover how far Pt-nanoparticle contamination occurs along a CNT after FIB electrical contact deposition careful TEM inspections are performed. The results show FIB deposition efficiently improves electrical contact; however, the practice is accompanied by serious particle contamination near deposition points. These contaminants include metal particles and amorphous elements originating from precursor gases and residual water molecules in the vacuum chamber. Pt-contamination extends for approximately 2 µm from the point of FIB contact deposition. These contaminants cause current fluctuations and alter the transport characteristics of devices. It is recommended that nano-device fabrication occurs at a distance greater than 2 µm from the FIB deposition of an electrical contact.

Polymer-free patterning of graphene at sub-10-nm scale by low-energy repetitive electron beam.

A polymer-free technique for generating nanopatterns on both synthesized and exfoliated graphene sheets is proposed and demonstrated. A low-energy (5-30 keV) scanning electron beam with variable repetition rates is used to etch suspended and unsuspended graphene sheets on designed locations. The patterning mechanisms involve a defect-induced knockout process in the initial etching stage and a heat-induced curling process in a later stage. Rough pattern edges appear due to inevitable stochastic knockout of carbon atoms or graphene structure imperfection and can be smoothed by thermal annealing. By using this technique, the minimum feature sizes achieved are about 5 nm for suspended and 7 nm for unsuspended graphene. This study demonstrates a polymer-free direct nanopatterning approach for graphene.

Resonant tunneling through discrete quantum states in stacked atomic-layered MoS2.

Two-dimensional crystals can be assembled into three-dimensional stacks with atomic layer precision, which have already shown plenty of fascinating physical phenomena and been used for prototype vertical-field-effect-transistors.1,2 In this work, interlayer electron tunneling in stacked high-quality crystalline MoS2 films were investigated. A trilayered MoS2 film was sandwiched between top and bottom electrodes with an adjacent bottom gate, and the discrete energy levels in each layer could be tuned by bias and gate voltages. When the discrete energy levels aligned, a resonant tunneling peak appeared in the current-voltage characteristics. The peak position shifts linearly with perpendicular magnetic field, indicating formation of Landau levels. From this linear dependence, the effective mass and Fermi velocity are determined and are confirmed by electronic structure calculations. These fundamental parameters are useful for exploitation of its unique properties.

Improving nanowire sensing capability by electrical field alignment of surface probing molecules.

We argue that the structure ordering of self-assembled probing molecular monolayers is essential for the reliability and sensitivity of nanowire-based field-effect sensors because it can promote the efficiency for molecular interactions as well as strengthen the molecular dipole field experienced by the nanowires. In the case of monolayers, we showed that structure ordering could be improved by means of electrical field alignment. This technique was then employed to align multilayer complexes for nanowire sensing applications. The sensitivity we achieved for detection of hybridization between 15-base single-strand DNA molecules is 0.1 fM and for alcohol sensors is 0.5 ppm. The reliability was confirmed by repeated tests on chips that contain multiple nanowire sensors.

Photo-response of a nanopore device with a single embedded ZnO nanoparticle.

The photo-response of a ZnO nanoparticle embedded in a nanopore made on a silicon nitride membrane is investigated. The ZnO nanoparticle is manipulated onto the nanopore and sandwiched between aluminum contact electrodes from both the top and bottom. The asymmetric device structure facilitates current-voltage rectification that enables photovoltaic capacity. Under illumination, the device shows open-circuit voltage as well as short-circuit current. The fill factor is found to increase at low temperatures and reaches 48.6% at 100 K. The nanopore structure and the manipulation technique provide a solid platform for exploring the electrical properties of single nanoparticles.

Monitoring extracellular K+ flux with a valinomycin-coated silicon nanowire field-effect transistor.

A silicon nanowire field-effect transistor (SiNW-FET) coated with a polyvinyl chloride (PVC) membrane containing valinomycin (VAL) was employed as a biosensor (referred to as VAL-PVC/SiNW-FET) to detect the K(+)-efflux from live chromaffin cells. The detection sensitivity of K(+) with the VAL-PVC/SiNW-FET covers a broad range of concentrations from 10(-6) to 10(-2) M. The apparent association constants between VAL and Li(+), Na(+), K(+), and Cs(+) in Tris buffer solution were determined to be 67±42, 120±23, 5974±115, and 4121±140 M(-1), respectively. By culturing chromaffin cells on the VAL-PVC/SiNW-FET, the conductance was significantly increased by nicotine stimulation in a bath buffer without Na(+). The K(+) concentration at the cell surface was determined to be ~20 µM under the stimulation of 5 mM nicotine. These results demonstrate that the VAL-PVC/SiNW-FET is sensitive and selective to detect the released K(+) from cells and is suitable for applications in cellular recording investigations.

Direct observation of electron dephasing due to inelastic scattering from defects in weakly disordered AuPd wires.

To identify and investigate the mechanisms of electron-phonon (e-ph) relaxation in weakly disordered metallic conductors, we measure the electron dephasing rate in a series of suspended and supported 15-nm thick AuPd wires. In a wide temperature range, from ∼8 K to above 20 K, the e-ph interaction dominates in the dephasing processes. The corresponding relaxation rate reveals a quadratic temperature dependence, τ(e-ph)(-1)=A(ep)T2, where A(ep)≈5×10(9) K(-2) s(-1) is essentially the same for all samples studied. Our observations are shown to be in good agreement with the theory which predicts that, even in weakly disordered metallic structures at moderately low temperatures, the major mechanism of the e-ph relaxation is the electron scattering from vibrating defects and impurities.