ABSTRACT
A steel ball with a density higher than that of water can bounce on a water surface when heated to a temperature well above the Leidenfrost point. In this letter, an experiment is conducted where heated steel balls are released onto a water surface. The heated steel ball descends into the liquid, thus causing the liquid to evaporate and form a vapor cushion with an upward force that lifts the steel ball. Subsequently, the steel ball bounces off the water surface, like a solid ball bouncing off an elastic surface without sinking into the water. This phenomenon is known as the inverse Leidenfrost effect. In this letter, we evaluate the various motion behaviors of spheres at different Reynolds numbers and temperatures. Additionally, we analyze the bouncing behavior of solid spheres on a free liquid surface and examine the various force components.
ABSTRACT
Optical paths in telescopes frequently incorporate silver mirrors for high sensitivity. Unfortunately, silver mirrors without protective coatings are susceptible to sulfurization and oxidation, compromising their quality. Even with protective layers, insufficient adhesion between the coating and the silver film can lead to peeling, exposing the silver to external environments and affecting its quality. This study aimed to identify dielectric materials with superior adhesion to silver, rendering them ideal choices for silver coating applications. By electron gun evaporation, different dielectric layers were deposited on the top and bottom of the silver film under a substrate temperature below 150 °C. These coatings were composed of materials with desired refractive indices, including aluminum oxide (Al2O3), aluminum-doped silicon, magnesium fluoride (MgF2), and other dielectrics. Following the deposition, a tape adhesion test was conducted to evaluate the bond strength of the samples. X-ray photoelectron spectroscopy (XPS) analysis was carried out to investigate the interaction between silver and its neighboring layers. The results revealed that Al2O3 and MgF2 exhibited exceptional adhesion to silver. Moreover, these multilayer coatings can effectively enhance the reflectance of silver in the visible (VIS) wavelength ranges.
ABSTRACT
Systemic lupus erythematosus (SLE) is a chronic autoimmune disease in which multiple organs are damaged that prevails in fertile women. Currently, glucocorticoids and immunosuppressants are widely used to treat SLE patients. However, ovarian dysfunction occurs following the use of these drugs in women with SLE. Here, we summarize recent progress in terms of understanding ovarian injury, the effects of drug application and strategies to improve ovarian function in women with SLE. This review could be helpful to precisely cure SLE in women desiring to have offspring.
ABSTRACT
Mesenchymal stem cells (MSCs) are stem/progenitor cells capable of self-renewal and differentiation into osteoblasts, chondrocytes and adipocytes. The transformation of multipotent MSCs to adipocytes mainly involves two subsequent steps from MSCs to preadipocytes and further preadipocytes into adipocytes, in which the process MSCs are precisely controlled to commit to the adipogenic lineage and then mature into adipocytes. Previous studies have shown that the master transcription factors C/enhancer-binding protein alpha and peroxisome proliferation activator receptor gamma play vital roles in adipogenesis. However, the mechanism underlying the adipogenic differentiation of MSCs is not fully understood. Here, the current knowledge of adipogenic differentiation in MSCs is reviewed, focusing on signaling pathways, noncoding RNAs and epigenetic effects on DNA methylation and acetylation during MSC differentiation. Finally, the relationship between maladipogenic differentiation and diseases is briefly discussed. We hope that this review can broaden and deepen our understanding of how MSCs turn into adipocytes.
ABSTRACT
In low-pressure wax injection molding, cooling time refers to the period during which the molten plastic inside the mold solidifies and cools down to a temperature where it can be safely ejected without deformation. However, cooling efficiency for the mass production of injection-molded wax patterns is crucial. This work aims to investigate the impact of varying surface roughness on the inner walls of the cooling channel on the cooling efficiency of an aluminum-filled epoxy resin rapid tool. It was found that the cooling time for the injection-molded products can be determined by the surface roughness according to the proposed prediction equation. Employing fiber laser processing on high-speed steel rods allows for the creation of microstructures with different surface roughness levels. Results demonstrate a clear link between the surface roughness of cooling channel walls and cooling time for molded wax patterns. Employing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm for low-pressure wax injection molding can save time, with a cooling efficiency improvement of approximately 34%. Utilizing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm on the inner walls of the cooling channel can save the cooling time by up to approximately 60%. These findings underscore the significant role of cooling channel surface roughness in optimizing injection molding processes for enhanced efficiency.
ABSTRACT
PURPOSE: Acknowledging the associated risk factors may have a positive impact on reducing the incidence of ectopic pregnancy (EP). In recent years, body mass index (BMI) has been mentioned in research. However, few studies are available and controversial on the relationship between EP and BMI. METHODS: We retrospectively studied the EP women as a case group and the deliveries as a control group in the central hospital of Wuhan during 2017 ~ 2021. χ2 test of variables associated with ectopic pregnancy was performed to find differences. Univariate and multivariate binary logistic regression analysis was conducted to analyze the association of the variables of age, parity, history of induced abortion, history of ectopic pregnancy, history of spontaneous abortion, history of appendectomy surgery and BMI (< 18.5 kg/m2, 18.5 ~ 24.9 kg/m2, 25 kg/m2 ~ 29.9 kg/m2, ≥ 30 kg /m2) with EP. RESULTS: They were 659 EP and 1460 deliveries. The variables of age, parity, history of induced abortion, history of ectopic pregnancy and BMI were different significantly(P < 0.05). Multivariate analysis showed that the variables of age > 35 years old [(OR (Odds Ratio), 5.415; 95%CI (Confidence Interval), 4.006 ~ 7.320, P < 0.001], history of ectopic pregnancy (OR, 3.944; 95%CI, 2.405 ~ 6.467; P < 0.001), history of induced abortion(OR, 3.365; 95%CI, 2.724 ~ 4.158, P < 0.001) and low BMI (< 18.5 kg/m2) (OR, 1.929; 95%CI, 1.416 ~ 2.628, P < 0.001])increased the risk of EP. CONCLUSION: The history of ectopic pregnancy, history of induced abortion and age > 35 years old were the risk factors with EP. In addition to these traditional factors, we found low BMI (< 18.5 kg/m2) with women may increase the risk to EP.
Subject(s)
Abortion, Induced , Pregnancy, Ectopic , Pregnancy , Female , Humans , Adult , Retrospective Studies , Case-Control Studies , Body Mass Index , Pregnancy, Ectopic/epidemiology , Pregnancy, Ectopic/etiology , Abortion, Induced/adverse effects , Risk FactorsABSTRACT
Notwithstanding recent advances in direct antiviral specialists (DAAs) for hepatitis C infection (HCV), it is yet a pervasive overall issue in patients with rheumatoid arthritis (RA). Exosomal microRNAs (miRNAs) is associated with HCV infection. However, it remains unknown how miRNAs respond following biologic disease-modifying antirheumatic drug (bDMARD) and targeted synthetic DMARD (tsDMARD) treatment in HCV patients with RA. We prospectively recruited RA patients taking anti-tumor necrosis factor-α (TNF-α) inhibitors rituximab (RTX) and tofacitinib. The serum hepatitis C viral load was measured using real-time quantitative reverse transcriptase PCR before and 6 months after bDMARD and tsDMARD therapy. HCV RNA replication activity was measured using an HCV-tricistronic replicon reporter system, and quantitative analysis of hsa-mir-122-5p and hsa-mir-155-5p in patients was performed using quantitative PCR. HCV RNA replication in hepatocytes was not affected by tofacitinib or TNF-α inhibitor treatment. Hsa-mir-155-5p and hsa-mir-122-5p were significantly expanded in RA patients with HCV as compared with those without HCV. We observed a dramatic increase in hsa-mir-122-5p and a decrease in hsa-mir-155-5p expression levels in patients taking RTX in comparison with other treatments. Finally, a reduction in hsa-mir-122-5p and an increase in hsa-mir-155-5p were observed in a time-dependent manner after tofacitinib and DAA therapy in RA-HCV patients. These results showed that hsa-mir-155-5p and hsa-mir-122-5p were significantly increased in RA-HCV patients as compared with those without HCV after taking tofacitinib. Hsa-mir-155-5p and hsa-mir-122-5p may be potential biomarkers for treatment efficacy in RA patients with HCV.
Subject(s)
Antirheumatic Agents , Arthritis, Rheumatoid , Hepatitis C, Chronic , Hepatitis C , MicroRNAs , Humans , MicroRNAs/genetics , Antiviral Agents/pharmacology , Antiviral Agents/therapeutic use , Tumor Necrosis Factor-alpha , Hepatitis C, Chronic/drug therapy , Hepatitis C, Chronic/genetics , Hepacivirus/genetics , Hepatitis C/drug therapy , Hepatitis C/genetics , Virus Replication , Arthritis, Rheumatoid/drug therapy , Arthritis, Rheumatoid/genetics , Rituximab , Antirheumatic Agents/pharmacology , Antirheumatic Agents/therapeutic use , BiomarkersABSTRACT
Three-dimensional printing is widely used for manufacturing a variety of functional components. However, the 3D printing machine substantially limits the size of the functional components. Rotary friction welding (RFW) is a possible solution to this problem. In addition, there is a notable scarcity of research directed toward the domain knowledge of RFW involving dissimilar polymer rods containing metal powder. In this study, two welding specimens fabricated by polylactic acid (PLA)-containing copper powder and PLA-containing aluminum powder were joined using a turning machine. After RFW, a bending test and a Shore A surface hardness test were performed to investigate the weld quality. It was found that the bending strength of the welded parts fabricated by RFW of PLA and PLA-containing Al powder rods can be enhanced by about 57.5% when the welded part is placed at 45 °C. Surface hardness test results showed that the surface hardness of the weld interface is better than that of the 3D printed parts, and the average surface hardness of the weld interface from RFW of PLA and PLA is the highest. The surface hardness of the weld joint is about 3% higher than that of the base material. The surface hardness of the heat-affected zone is about 3% lower than that of the base material. The average peak temperature of the welded joint is the highest in the RFW of PLA-containing Al powder and PLA-containing Al powder rods. The average peak temperature of the weld joint can be as high as 160 °C. The average peak temperature of the welded joint is the highest in the RFW of PLA-containing Cu powder and PLA-containing Cu powder rods. The average peak temperature of the welded joint can be as high as 144 °C. A technical database was built for the selection of ambient temperatures used for the RFW of dissimilar polymer rods containing metal powder and three base materials.
ABSTRACT
Faba bean is an important cool-season edible legume crop that is constantly threatened by abiotic stresses such as drought. The basic leucine zipper (bZIP) gene family is one of the most abundant and diverse families of transcription factors in plants. It regulates plant growth and development and plays an important role in the response to biotic and abiotic stresses. In this study, we identified 18 members of the faba bean bZIP transcription factor family at the genome-wide level based on previous faba bean drought stress transcriptome sequencing data. A phylogenetic tree was constructed to group the 18 VfbZIP proteins into eight clades. Analysis of cis-acting elements in the promoter region suggested that these 18 VfbZIPs may be involved in regulating abiotic stress responses such as drought. Transcriptome data showed high expression of seven genes (VfbZIP1, VfbZIP2, VfbZIP5, VfbZIP7, VfbZIP15, VfbZIP17, and VfbZIP18) in the drought-tolerant cultivar under drought stress, in which VfbZIP1, VfbZIP2, and VfbZIP5 were consistently expressed as detected by quantitative real-time polymerase chain reaction (qRT-PCR) compared to the transcriptome data. Ectopic overexpression of the three VfbZIPs in tobacco, based on the potato Virus X (PVX) vector, revealed that VfbZIP5 enhanced the drought tolerance. Overexpressed VfbZIP5 in plants showed lower levels of proline (PRO), malondialdehyde (MDA), and peroxidase (POD) compared to those overexpressing an empty vector under 10 days of drought stress. Protein-protein interaction (PPI) analysis showed that VfbZIP5 interacted with seven proteins in faba bean, including VfbZIP7 and VfbZIP10. The results depict the importance of VfbZIPs in response to drought stress, and they would be useful for the improvement of drought tolerance.
ABSTRACT
Rotary friction welding (RFW) is a green manufacturing technology with environmental pollution in the field of joining methods. In practice, the welding quality of the friction-welded parts was affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. In industry, polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) are two commonly used plastics in consumer products. In this study, the COMSOL multiphysics software was employed to estimate the peak temperature in the weld joint during the RFW of PC and ABS rods. After RFW, the mechanical performance and microstructural evolution of friction-welded parts were investigated experimentally. The average Shore A surface hardness, flexural strength, and impact energy are directly proportional to the rotation speed of the RFW. The quality of RFW is excellent, since the welding strength in the weld joint is better than that of the ABS base materials. The fracture occurs in the ABS rods since their brittleness is higher than that of the PC rods. The average percentage error of predicting the peak temperature using COMSOL software using a mesh element count of 875,688 for five different rotation speeds is about 16.6%. The differential scanning calorimetry curve for the friction-welded parts welded at a rotation speed of 1350 rpm shows an endothermic peak between 400 to 440 °C and an exothermic peak between 600 to 700 °C, showing that the friction-welded parts have better mechanical properties.
ABSTRACT
Rotary friction welding (RFW) could result in lower welding temperature, energy consumption, or environmental effects as compared with fusion welding processes. RFW is a green manufacturing technology with little environmental pollution in the field of joining methods. Thus, RFW is widely employed to manufacture green products. In general, the welding quality of welded parts, such as tensile strength, bending strength, and surface hardness is affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. However, hitherto little is known about the domain knowledge of RFW of acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) polymer rods. To prevent random efforts and energy consumption, a green method to predict the peak temperature in the weld joint of dissimilar RFW of ABS and PC rods was proposed. The main objective of this work is to investigate the peak temperature in the weld joint during the RFW using COMSOL multiphysics software for establishing an empirical technical database of RFW of dissimilar polymer rods under different rotational speeds. The main findings include that the peak temperature affecting the mechanical properties of RFW of PC and ABS can be determined by the simulation model proposed in this work. The average error of predicting the peak temperature using COMSOL software for five different rotational speeds is about 15 °C. The mesh element count of 875,688 is the optimal number of meshes for predicting peak temperature in the weld joint. The bending strength of the welded part (y) using peak welding temperature (x) can be predicted by the equation of y = -0.019 x2 + 5.081x - 200.75 with a correlation coefficient of 0.8857. The average shore A surface hardness, impact energy, and bending strength of the welded parts were found to be increased with increasing the rotational speed of RFW.
ABSTRACT
A total of 58 (eight known and 50 new) species of the subgenus Stegana (Steganina) from China were surveyed and (re)described: S. (S.) bacilla Chen & Aotsuka, 2004, S. (S.) belokobylskiji Sidorenko, 1997, S. (S.) hirticeps Wang, Gao, & Chen, 2013, S. (S.) izu Sidorenko, 1997, S. (S.) kanmiyai Okada & Sidorenko, 1992, S. (S.) masanoritodai Okada & Sidorenko, 1992, S. (S.) maymyo Sidorenko, 1997, stat. rev., S. (S.) nigripes Zhang & Chen, 2015, S. (S.) alafoliacea Zhang & Chen, sp. nov., S. (S.) baoxing Li & Chen, sp. nov., S. (S.) bibarbata Li & Chen, sp. nov., S. (S.) bimai Cui & Chen, sp. nov., S. (S.) cinereipecta Zhang & Chen, sp. nov., S. (S.) cardua Cui & Chen, sp. nov., S. (S.) cordhirsuta Wang & Chen, sp. nov., S. (S.) cornuta Li & Chen, sp. nov., S. (S.) cucullata Li & Chen, sp. nov., S. (S.) cultella Cui & Chen, sp. nov., S. (S.) curvitabulata Cui & Chen, sp. nov., S. (S.) daiya Cui & Chen, sp. nov., S. (S.) dendrophila Zhang & Chen, sp. nov., S. (S.) flabella Li & Chen, sp. nov., S. (S.) flavipes Li & Chen, sp. nov., S. (S.) formosa Zhang & Chen, sp. nov., S. (S.) fusca Li & Chen, sp. nov., S. (S.) fuscipes Li & Chen, sp. nov., S. (S.) glaucopalpula Cui & Chen, sp. nov., S. (S.) haba Zhang & Chen, sp. nov., S. (S.) hirticlavata Cui & Chen, sp. nov., S. (S.) iaspidea Zhang & Chen, sp. nov., S. (S.) idiasta Cui & Chen, sp. nov., S. (S.) kanda Cui & Chen, sp. nov., S. (S.) labao Li & Chen, sp. nov., S. (S.) lancang Li & Chen, sp. nov., S. (S.) latifoliacea Wang & Chen, sp. nov., S. (S.) liusanjieae Li & Chen, sp. nov., S. (S.) magniflava Cui & Chen, sp. nov., S. (S.) mailangang Li & Chen, sp. nov., S. (S.) marenubila Cui & Chen, sp. nov., S. (S.) menghai Zhang & Chen, sp. nov., S. (S.) menglian Li & Chen, sp. nov., S. (S.) minutiflava Li & Chen, sp. nov., S. (S.) multiprocera Li & Chen, sp. nov., S. (S.) nayun Li & Chen, sp. nov., S. (S.) nigridentata Wang & Chen, sp. nov., S. (S.) nigripalpula Cui & Chen, sp. nov., S. (S.) otphylla Cui & Chen, sp. nov., S. (S.) radiciflava Zhang & Chen, sp. nov., S. (S.) rava Cui & Chen, sp. nov., S. (S.) sciophila Li & Chen, sp. nov., S. (S.) septencolorata Li & Chen, sp. nov., S. (S.) serrata Zhang & Chen, sp. nov., S. (S.) silvestrella Zhang & Chen, sp. nov., S. (S.) simola Cui & Chen, sp. nov., S. (S.) yani Li & Chen, sp. nov., S. (S.) yixiang Zhang & Chen, sp. nov., S. (S.) zaduo Cui & Chen, sp. nov., and S. (S.) zhuoma Cui & Chen, sp. nov. We also provided a complete list of Chinese Steganina species together with their geographical distributions. In addition, the majority of currently available DNA barcode (partial sequence of the mitochondrial cytochrome c oxidase subunit I (COI) gene) sequences of this subgenus (435 sequences of 102 spp.) were employed in a molecular analysis for species delimitation. Taken together, morphology- and molecular-based species delimitation results reached a consensus for an overwhelming majority of these Steganina species (98 of 102 spp.).
Subject(s)
Drosophilidae , Animals , Drosophilidae/genetics , DNA Barcoding, Taxonomic , Phylogeny , China , DNAABSTRACT
Friction welding (FW) FW of dissimilar polymer rods is capable of manufacturing green products swiftly and economically. In this study, a green manufacturing technique of joining dissimilar polymer rods was proposed, and the effects of rotational speed on the joint characteristics of friction-welded dissimilar polymer rods fabricated by the fused deposition modeling process were investigated experimentally. The shore surface hardness test, impact test, three-point bending test, and differential scanning calorimetry analysis were carried out on the weld joints. The impact energy for FW of polylactic acid (PLA) and PLA, PLA and acrylonitrile butadiene styrene (ABS), PLA and PLA filled with glass fiber (GF), PLA and PLA filled with carbon fiber (CF), PLA and polycarbonate (PC), and PLA and polyamide (PA) rods can be increased by approximately 1.5, 1.5, 1.3, 1.3, 2.1, and 1.5 times by increasing the rotational speed from 330 rpm to 1350 rpm. The bending strength for FW of PLA and PLA, PLA and ABS, PLA and PLA filled with GF, PLA and PLA filled with CF, PLA and PC, and PLA and PA rods can be increased by approximately 1.3, 1.7, 1.3, 1.2, 1.2, and 1.2 times by increasing the rotational speed from 330 rpm to 1350 rpm. However, the surface hardness of the weld bead is not proportional to the rotational speed. The average surface hardness of the weld bead was increased by approximately 5% compared to the surface hardness of the welding base materials.
ABSTRACT
Objectives: To investigate the differences between the vector vaccine ChAdOx1 nCoV-19/AZD1222 (Oxford-AstraZeneca) and mRNA-based vaccine mRNA-1273 (Moderna) in patients with autoimmune rheumatic diseases (AIRD), and to explore the cell-cell interactions between high and low anti-SARS-CoV-2 IgG levels in patients with rheumatic arthritis (RA) using single-cell RNA sequencing (scRNA-seq). Methods: From September 16 to December 10, 2021, we consecutively enrolled 445 participants (389 patients with AIRD and 56 healthy controls), of whom 236 were immunized with AZD1222 and 209 with mRNA-1273. The serum IgG antibodies to the SARS-CoV-2 receptor-binding domain was quantified by electrochemiluminescence immunoassay at 4-6 weeks after vaccination. Moreover, peripheral blood mononuclear cells (PBMCs) were isolated from RA patients at 4-6 weeks after vaccination for scRNA-seq and further analyzed by CellChat. ScRNA-seq of PBMCs samples from GSE201534 in the Gene Expression Omnibus (GEO) database were also extracted for analysis. Results: The anti-SARS-CoV-2 IgG seropositivity rate was 85.34% for AIRD patients and 98.20% for healthy controls. The anti-SARS-CoV-2 IgG level was higher in patients receiving mRNA-1273 than those receiving AZD1222 (ß: 35.25, 95% CI: 14.81-55.68, p=0.001). Prednisolone-equivalent dose >5 mg/day and methotrexate use in AIRD patients, and non-anti-tumor necrosis factor-α biologics and Janus kinase inhibitor use in RA patients were associated with inferior immunogenicity. ScRNA-seq revealed CD16-monocytes were predominant in RA patients with high anti-SARS-CoV2-IgG antibodies, and enriched pathways related to antigen presentation via MHC class II were found. HLA-DRA and CD4 interaction was enhanced in high anti-SARS-CoV2-IgG group. Conclusions: mRNA-1273 and AZD1222 vaccines exhibited differential immunogenicity in AIRD patients. Enriched pathways related to antigen presentation via MHC class II in CD16-monocytes might be associated with higher anti-SARS-CoV2-IgG level in RA patients and further study is warranted.
Subject(s)
Autoimmune Diseases , COVID-19 , Rheumatic Diseases , 2019-nCoV Vaccine mRNA-1273 , Antibodies, Viral , COVID-19/prevention & control , ChAdOx1 nCoV-19 , Humans , Immunoglobulin G , Leukocytes, Mononuclear , Rheumatic Diseases/drug therapy , SARS-CoV-2 , Sequence Analysis, RNA , mRNA VaccinesABSTRACT
The precise control of cardiomyocyte viability is imperative to combat myocardial ischemia-reperfusion injury (I/R), in which apoptosis and pyroptosis putatively contribute to the process. Recent researches indicated that GSDMD is involved in I/R as an executive protein of pyroptosis. However, its effect on other forms of cell death is unclear. We identified that GSDMD and GSDMD-N levels were significantly upregulated in the I/R myocardium of mice. Knockout of GSDMD conferred the resistance of the hearts to reperfusion injury in the acute phase of I/R but aggravated reperfusion injury in the chronic phase of I/R. Mechanistically, GSDMD deficiency induced the activation of PARylation and the consumption of NAD+ and ATP, leading to cardiomyocyte apoptosis. Moreover, PJ34, a putative PARP-1 inhibitor, reduced the myocardial injury caused by GSDMD deficiency. Our results reveal a novel action modality of GSDMD in the regulation of cardiomyocyte death; inhibition of GSDMD activates PARylation, suggesting the multidirectional role of GSDMD in I/R and providing a new theory for clinical treatment.
Subject(s)
Myocardial Reperfusion Injury , Animals , Mice , Mice, Knockout , Myocytes, Cardiac , Poly ADP Ribosylation , PyroptosisABSTRACT
Highly reflective metal coatings are essential for manufacturing reflecting telescope mirrors to achieve the highest reflectivity with broad spectral bandwidth. Among metallic materials, enhanced silver-based coatings can provide higher reflectivity in the 400-500 nm spectral range to better performance from visible to near IR. Moreover, over-coating a dielectric protective layer on the mirror's front side attains additional hardness and oxidation stability. In this paper, we study a combination of thermal and electron beam evaporation as a technology to form protected enhanced high reflective Ag coatings. A newly designed multiplayer film can pass ASTM 5B adhesive performance testing and give sulfurization inhibition. The average specular reflectivity for the enhancement coating is about 98% in wavelengths across the spectral range from 400-1000 nm. This innovation has been demonstrated on a Newtonian type telescope, with storage in an ambiance humidity H = 60-85%, and temperature T = 10-35 °C, for more than six months without degradation in coating performance.
ABSTRACT
Inspired by Roush's pioneering work on rare sugars, we have developed a scalable, stereoselective, de novo synthesis of orthogonally protected C2-fluoro digitoxose and cymarose, utilizing Sharpless kinetic resolution and organocatalytic fluorination as key steps. The utility of this strategy is demonstrated by the synthesis of a fluorinated analogue of digoxin, which indicates the fluorine on the sugar ring may have a significant impact on biological activity.
Subject(s)
Digoxin , Fluorine , Halogenation , Hexoses , StereoisomerismABSTRACT
OBJECTIVE: To compare the therapeutic effect of different animal bile powders on lipid metabolism disorders induced by high-fat diet in rats, and analyze the bioactive components of each animal bile powder. METHODS: Sixty Sprague-Dawley rats were randomly divided into 6 groups (n=10): normal diet control group, high-fat diet model group, high-fat diet groups orally treated with bear, pig, cow and chicken bile powders, respectively. Serum biochemical markers from the abdominal aorta in each group were analyzed. Changes in the body weight and liver weight were recorded. Pathohistological changes in the livers were examined. High performance liquid chromatography coupled with quadrupole time-of-flight tandem mass spectrometry was used to determine the composition of bioactive components in each animal bile powder. RESULTS: Treatment with different types of animal bile powders had different inhibitory effects on high-fat diet-induced increase of body weight and/or liver weight in rats, most notably in bear and pig bile powders (P<0.05). High-fat diet induced lipid metabolism disorder in rats, which could be reversed by treatment with all kinds of bile powders. Bear bile and chicken bile showed the most potent therapeutic effect against lipid metabolism disorder. Cow and bear bile effectively alleviated high-fat diet induced liver enlargement and discoloration, hepatocyte swelling, infiltration of inflammatory cells and formation of lipid vacuoles. Bioactive component analysis revealed that there were significant differences in the relative content of taurocholic acid, taurodeoxycholic acid and ursodeoxycholic acid among different types of animal bile. Interestingly, a unique component with molecular weight of 496.2738 Da, whose function has not yet been reported, was identified only in bear bile powder. CONCLUSIONS: Different animal bile powders had varying therapeutic effect against lipid metabolism disorders induced by high-fat diet, and bear bile powder demonstrated the most effective benefits. Bioactive compositions were different in different types of animal bile with a novel compound identified only in bear bile powder.
Subject(s)
Lipid Metabolism Disorders , Ursidae , Animals , Bile/chemistry , Bile/metabolism , Biomarkers/metabolism , Body Weight , Cattle , Diet, High-Fat , Female , Lipid Metabolism , Lipid Metabolism Disorders/metabolism , Lipids/analysis , Liver/metabolism , Powders , Rats , Rats, Sprague-Dawley , Swine , Taurodeoxycholic Acid/analysis , Taurodeoxycholic Acid/metabolism , Ursidae/metabolism , Ursodeoxycholic Acid/analysis , Ursodeoxycholic Acid/metabolismABSTRACT
BACKGROUND: Cross-border malaria in Laiza City of Myanmar seriously affected Yingjiang County of China and compromised reaching the goal of malaria elimination by 2020. Since 2017, a pilot project on 3 + 1 strategy of joint cross-border malaria prevention and control was carried out for building a malaria buffer in these border areas. Here, 3 were the three preventive lines in China where different focalized approaches of malaria elimination were applied and + 1 was a defined border area in Myanmar where the integrated measures of malaria control were adopted. METHODS: A 5-year retrospective analysis (2015 to 2019) was conducted that included case detection, parasite prevalence and vector surveillance. Descriptive statistics was used and the incidence or rates were compared. The annual parasite incidence and the parasite prevalence rate in + 1 area of Myanmar, the annual importation rate in Yingjiang County of China and the density of An. minimus were statistically significant indictors to assess the effectiveness of the 3 + 1 strategy. RESULTS: In + 1 area of Myanmar from 2015 to 2019, the averaged annual parasite incidence was (59.11 ± 40.73)/1000 and Plasmodium vivax accounted for 96.27% of the total confirmed cases. After the pilot project, the annual parasite incidence dropped 89% from 104.77/1000 in 2016 to 12.18/1000 in 2019, the microscopic parasite prevalence rate dropped 100% from 0.34% in 2017 to zero in 2019 and the averaged density of An. Minimus per trap-night dropped 93% from 1.92 in June to 0.13 in September. The submicroscopic parasite prevalence rate increased from 1.15% in 2017 to 1.66% in 2019 without significant difference between the two surveys (P = 0.084). In Yingjiang County of China, neither indigenous nor introduced case was reported and 100% cases were imported from Myanmar since 2017. The averaged annual importation rate from 2015 to 2019 was (0.47 ± 0.15)/1000. After the pilot project, the annual importation rate dropped from 0.59/1000 in 2016 to 0.28/1000 in 2019 with an overall reduction of 53% in the whole county. The reduction was 67% (57.63/1000 to 18.01/1000) in the first preventive line, 52% (0.20/1000 to 0.10/1000) in the second preventive line and 36% (0.32/1000 to 0.22/1000) in the third preventive line. The averaged density of An. Minimus per trap-night in the first preventive line dropped 94% from 2.55 in June to 0.14 in September, without significant difference from that of + 1 area of Myanmar (Z value = - 1.18, P value = 0.24). CONCLUSION: The pilot project on 3 + 1 strategy has been significantly effective in the study areas and a buffer zone of border malaria was successfully established between Laiza City of Myanmar and Yingjiang County of China.
Subject(s)
Malaria , China/epidemiology , Humans , Malaria/epidemiology , Malaria/prevention & control , Myanmar/epidemiology , Pilot Projects , Retrospective StudiesABSTRACT
Non-alcoholic fatty liver disease (NAFLD) is the most common chronic liver disease characterized by excessive fat accumulation in the liver. The aim of this study is to elucidate the multi-target mechanism of polyphenols in blueberry leaves (PBL) on NAFLD by network pharmacology and to validate its results via biological experiments. Twenty constituents in PBL were preliminarily determined by liquid chromatography-tandem mass spectrometry. Subsequently, 141 predicted drug targets and 1226 targets associated with NAFLD were retrieved from public databases, respectively. The herb-compound-target network and the target protein-protein interaction network (PPI) were established through Cytoscape software, and four compounds and 53 corresponding targets were identified. Gene Ontology (GO) enrichment and Kyoto Encyclopedia of Genes and Genomes (KEGG) pathway enrichment were performed to explore the biological processes of the predicted genes. The results of cell experiments demonstrated that PBL could significantly improve the viability of the NAFLD cell model, and the protein expressions of caspase-3 and Bcl-2 were consistent with the expected mechanism of action of PBL. Those results systematically revealed that the multi-target mechanism of PBL against NAFLD was related to the apoptosis pathway, which could bring deeper reflections into the hepatoprotective effect of PBL.