Compact thermal imager: a flight demonstration of infrared technology for Earth observations.

During 2019, an infrared camera, the compact thermal imager (CTI), recorded 15 million images of the Earth from the International Space Station. CTI is based on strained-layer superlattice (SLS) detector technology. The camera covered the spectral range from 3 to 11 µm in two spectral channels, 3.3-5.4 and 7.8-10.7 µm. Individual image frames were 26×21km2 projected on the ground, with 82 m pixel resolution. A frame time of 2.54 s created continuous image swaths with a 13% along-track image overlap. Upper limits determined on the ground and in flight for the electronic offset, read noise, and dark current demonstrated the stability of the SLS detector and camera over many months. Temperature calibration was established using a combination of preflight and in-flight measurements. A narrowband approximation of temperature as a function of photon counts produced an analytic relationship covering a temperature range of 0°-400°C. Examples of CTI images illustrate temperature retrievals over sea ice, urban and agricultural areas, desert, and wildfires.

Resonant structures for infrared detection.

We are developing resonator-quantum well infrared photodetectors (R-QWIPs) for long-wavelength applications. Detector pixels with 25 µm pitch were hybridized to fan-out circuits for radiometric measurements. With a moderate doping of 0.5×1018 cm-3, we achieved a quantum efficiency (QE) of 37% and conversion efficiency (CE) of 15% in a 1.3 µm thick active material and 35% QE and 21% CE in a 0.6 µm thick active material. Both detectors are cutoff at 10.5 µm with a 2 µm bandwidth. The temperature at which photocurrent equals dark current is about 65 K under F/2 optics. The thicker detector shows a large QE polarity asymmetry due to nonlinear potential drop in the QWIP material layers.

Optics research at the U.S. Army Research Laboratory.

The U.S. Army Research Laboratory (ARL) is the Army's premier laboratory for land forces. The Army relies on ARL for scientific discoveries, technological advances, and analyses that enable capabilities a future Army will need to persevere over adversaries. Although a relatively young organization that will celebrate 25 years of the discovery, innovation, and transition of science and technology in October 2017, ARL has already had significant impact in a wide range of scientific and technological disciplines. In this paper, we highlight some of its past and recent achievements in optics and photonics.

Clinical Effectiveness of Different Polishing Systems and Self-Etch Adhesives in Class V Composite Resin Restorations: Two-Year Randomized Controlled Clinical Trial.

The aim of this randomized controlled clinical trial was to compare the clinical effectiveness of different polishing systems and self-etch adhesives in class V composite resin restorations. A total of 164 noncarious cervical lesions (NCCLs) from 35 patients were randomly allocated to one of four experimental groups, each of which used a combination of polishing systems and adhesives. The two polishing systems used were Sof-Lex XT (Sof), a multistep abrasive disc, and Enhance/Pogo (EP), a simplified abrasive-impregnated rubber instrument. The adhesive systems were Clearfil SE bond (CS), a two-step self-etch adhesive, and Xeno V (XE), a one-step self-etch adhesive. All NCCLs were restored with light-cured microhybrid resin composites (Z250). Restorations were evaluated at baseline and at 6, 12, 18, and 24 months by two blinded independent examiners using modified FDI criteria. The Fisher exact test and generalized estimating equation analysis considering repeated measurements were performed to compare the outcomes between the polishing systems and adhesives. Three restorations were dislodged: two in CS/Sof and one in CS/EP. None of the restorations required any repair or retreatment except those showing retention loss. Sof was superior to EP with regard to surface luster, staining, and marginal adaptation (p<0.05). CS and XE did not show differences in any criteria (p>0.05). Sof is clinically superior to EP for polishing performance in class V composite resin restoration. XE demonstrates clinically equivalent bonding performance to CS.

Dietary exposure of the Hong Kong adult population to polybrominated diphenyl ethers (PBDEs): results of the first Hong Kong Total Diet Study.

Polybrominated diphenyl ethers (PBDEs) are a group of industrial chemicals that are persistent and can bioaccumulate. In the first Hong Kong Total Diet Study, the dietary exposure of Hong Kong adults to PBDEs was estimated to assess the associated health risks. Food samples, which represented the Hong Kong people's diet, were collected and prepared in table-ready form for analysis. Concentrations of PBDEs were determined in 142 composite samples. The dietary exposures were estimated by combining the analytical results with the local food consumption data of the adults. The mean and 95th percentile of dietary PBDEs exposures of the Hong Kong people were 1.34 and 2.90 ng kg(-1) body weight day(-1), respectively. The main dietary source of PBDEs was "fish and seafood and their products", which contributed 27.3% of the total exposure, followed by "meat, poultry and game and their products" (20.7%), "cereals and their products" (15.9%), and "fats and oils" (15.9%). The large margins of exposure (MOE) (>2.5) calculated following the European Food Safety Authority (EFSA) approach for four important congeners, BDE-47, BDE-99, BDE-153 and BDE-209, indicate that the estimated dietary exposures are unlikely to be a significant health concern.

Surgical strategies for non-functioning pancreatic neuroendocrine tumours.

BACKGROUND: The purpose of this study was to identify management strategies for non-functioning pancreatic neuroendocrine tumours (NF-PNETs) by analysis of surgical outcomes at a single institution. METHODS: Archived records of patients with NF-PNETs who underwent surgery between 1994 and 2010 were reviewed. RESULTS: Among 125 patients, the median tumour size was 2·5 (range 0·15-20·5) cm. Of the 51 NF-PNETs with a diameter of no more than 2 cm, 12 (24 per cent) were diagnosed as carcinoma. Overall 20 patients (16·0 per cent) had metastases to the lymph nodes. The minimum size of the tumour with lymph node metastasis was 1·2 cm. Having a NF-PNET of 2 cm or larger significantly increased the probability of a poorly differentiated carcinoma (P = 0·006), and having a NF-PNET of at least 2·5 cm significantly increased the probability of lymph node metastasis (P = 0·048). The 5-year cumulative survival rate after curative resection was 89·7 per cent. During a median follow-up of 31·5 months, there were 27 recurrences (23·1 per cent) and 13 disease-specific deaths (11·1 per cent) among the 117 patients who had an R0 resection. All patients who underwent repeat operations were alive without additional recurrence after a mean(s.d.) follow-up of 27·1(18·0) months. CONCLUSION: Curative surgery should be performed for control of primary NF-PNETs. Lymph node dissection for NF-PNETs of 2·5 cm or larger and at least node sampling for tumours with a diameter of 1 cm or more are recommended. Debulking surgery should be considered for advanced tumours.

Implication of ethanol wet-bonding in hybrid layer remineralization.

During mineralization, unbound water within the collagen matrix is replaced by apatite. This study tested the null hypothesis that there is no difference in the status of in vitro biomimetic remineralization of hybrid layers, regardless of their moisture contents. Acid-etched dentin was bonded with One-Step with ethanol-wet-bonding, water-wet-bonding, and water-overwet-bonding protocols. Composite-dentin slabs were subjected to remineralization for 1-4 months in a medium containing dual biomimetic analogs, with set Portland cement as the calcium source and characterized by transmission electron microscopy. Remineralization was either non-existent or restricted to the intrafibrillar mode in ethanol-wet-bonded specimens. Extensive intrafibrillar and interfibrillar remineralization was observed in water-wet-bonded specimens. Water-overwet specimens demonstrated partial remineralization of hybrid layers and precipitation of mineralized plates within water channels. The use of ethanol-wet-bonding substantiates that biomimetic remineralization is a progressive dehydration process that replaces residual water in hybrid layers with apatite crystallites.

Light-extraction enhancement of vertical-injection GaN-based light-emitting diodes fabricated with highly integrated surface textures.

We report on the fabrication of high-efficiency vertical-injection GaN-based light-emitting diodes (LEDs) fabricated with integrated surface textures. An optical ray-tracing simulation shows that the high integration of surface textures can effectively enhance the light-extraction efficiency. The integrated surface textures are fabricated on the top surface of LEDs by generating hexagonal cones on the periodically corrugated surfaces of n-GaN. Compared to reference LEDs without textures, LEDs fabricated with integrated surface textures show an enhancement of the output power by a factor of 2.59, which is in agreement with the calculated results.

A method for in-vivo analysis for regional arterial wall material property alterations with atherosclerosis: preliminary results.

Atherosclerosis is a diffuse arterial disease developing over many years and resulting in a complicated three-dimensional arterial morphology. The arterial wall material properties have been demonstrated to show regional alterations with atheroma development and growth. We present a mechanical analysis of diseased arterial segments reconstructed from intravascular ultrasound images in order to quantitatively identify regional alterations in the elastic constants with atherosclerotic lesions. We employ a finite element and a displacement sensitivity analysis to divide the arterial segment into regions with different material properties and use an optimization algorithm to identify the elastic constants in these regions. The results with regional variations identified with this method correlated qualitatively with the extent and location of atherosclerotic lesions identified by visual inspection of the affected arteries. The optimized elastic modulus in regions affected by early atherosclerotic lesions ranged from 90.9 to 93.0 kPa where as the corresponding magnitudes in normal arterial segments ranged from 97.9 to 101.0 kPa. This method can be potentially employed to identify the extent and location of atherosclerotic lesions in a systematic analysis and may potentially be used for the early detection of lesion growth.

The effects of adhesive thickness on polymerization contraction stress of composite.

A layer of an unfilled adhesive resin placed between the tooth and composite restoration has been shown to absorb some of the stress generated in the composite during polymerization and to reduce interfacial leakage. The objectives of this study were to measure the change in polymerization contraction stress of bonded composite as the thickness of the resin adhesive was systematically varied, and to correlate the effects of the adhesive thickness and reduced stress on marginal leakage in class V cavities. The maximum contraction force of composite (Herculite XRV) was measured in a tensilometer as the thickness of the adhesive bonding agent (Scotchbond MP) was varied from 20 to 300 microm. Composite was placed in Class V cavities prepared on the labial surfaces of bovine teeth to which different thicknesses of adhesive had been applied by layering, and a marginal leakage test was performed by means of staining with silver nitrate. Contraction stress decreased significantly as the adhesive thickness was increased. This result was supported by a theoretical examination of the data. In class V cavities, additional adhesive layering in the marginal area reduced the overall degree of microleakage. The contraction stress generated during the placement of a composite restoration contributes significantly to early marginal leakage, and this stress was significantly absorbed and relieved by the application of an increasing thickness of low-stiffness adhesive.

Properties of packable dental composites.

The introduction of many new packable composites suggests that these products are rapidly gaining popularity. The purpose of this study was to evaluate the in vitro properties of a variety of packable composites and to determine if significant enhancements in physical and mechanical properties have been achieved for these materials compared with two popular nonpackable posterior composites. For the five packable and two regular composites tested (ALERT, Pyramid-Dentin, Pyramid-Enamel, Solitaire, SureFil, Heliomolar, and Z100), the values for fracture toughness, flexure strength, flexure modulus, hardness, and volumetric polymerization shrinkage were determined. In general, although the packable composites were of heavier consistency, they had mechanical properties that were intermediate to (ALERT, Pyramid, and SureFil) or lower than (Solitaire) those of the nonpackable materials. These results could have been predicted based on the similar methacrylate resin chemistry and filler volumes of the various composites. No composite had adequate depth-of-cure when tested in increments greater than 2 mm thick. Polymerization contraction of the packable composites was similar to or higher than that of the nonpackable composites. In addition, the radiopacity of at least one material, Solitaire, was not considered to be adequate (less than 2 mm of aluminum). The results of this study suggest that these packable composites are unlikely to offer improved clinical performance over well-placed nonpackable composites.

In vitro wear of packable dental composites.

The in vitro abrasion and attrition wear of several packable composites were evaluated on the Oregon Health Sciences University oral wear simulator and compared to two popular commercial composites. In general, the wear of the packable composites was equivalent to that of the nonpackable microfill and minifill composites. The wear of the enamel cusps opposing the composites in the wear machine was also found to be similar to that of enamel opposing the nonpackable composites. Based on these results, one would expect that these new packable composites would not offer improved clinical performance over current nonpackable composites in terms of wear resistance.

Analysis of cement by atomic absorption spectrophotometry and volumetric method.

A new method to determine the composition of cement raw mix and cement is devised. The sample was fused with a mixture of sodium carbonate and lithium tetraborate (3:1) at 925 degrees C for 10 min. The fusion cake was dissolved in hydrochloric acid. The concentration of analyte in solution was either determined by atomic absorption spectrophotometry or titrimetry. The proposed method is quick and the analysis for interested oxides (SiO(2), Al(2)O(3), Fe(2)O(3), and CaO) can be completed within 1 hr. The accuracy and precision are comparable to that of X-ray fluorescence spectrometry.

Complexometric determination of magnesium oxide in flyash blended cement.

A complexometric titration method is proposed to determine magnesium oxide in flyash blended cement. A 0.50 g of sample was heated with hydrochloric acid for 10 min. The solution was diluted to 500 ml, and 50 ml was pipetted and heated to boiling with 2.5 ml of 5% ammonium oxalate solution. The solution was then made alkaline by ammonium hydroxide. The suspension was cooled and filtered. The filtrate was titrated by standard 0.002M EDTA solution. The concentration of MgO in sample was calculated. The flyash content of the sample was determined by British Standard method and the recovery factor (f) was calculated by the equation of f = 100/(99 - 0.315 x %FA). Concentration of MgO in sample was corrected by multiplying the recovery factor with concentration initially found by EDTA titration. The precision of the method is better with more time saving than the official methods.

Design sensitivity analysis: a new method for implant design and a comparison with parametric finite element analysis.

A unified theory of structural design sensitivity is proposed to be used in conjunction with the parametric design variation method traditionally used in finite element analyses applied to biomechanics problems. Bone cement strain energy density dependence on cement and stem modulii of elasticity as analyzed with the theory of structural design sensitivity analysis is compared parametrically varied finite element results. Two-dimensional, eight-noded isoparametric and interface finite elements with optimal stresses at Gauss points are employed. Design sensitivity for strain energy density compares well with perturbation of design and reanalysis by finite element techniques.