An investigation of the PM2.5 concentrations and cumulative inhaled dose during subway commutes in Changchun, China.

Air quality in subway systems is crucial as it affects the health of passengers and staff. Although most tests of PM2.5 concentrations in subway stations have taken place in public areas, PM2.5 is less understood in workplaces. Few studies have estimated the cumulative inhaled dose of passengers based on real-time changes in PM2.5 concentrations as they commute. To clarify the above issues, this study first measured PM2.5 concentrations in four subway stations in Changchun, China, where measuring points included five workrooms. Then, passengers' exposure to PM2.5 during the whole subway commute (20-30 min) was measured and segmented inhalation was calculated. The results showed that PM2.5 concentration in public places ranged from 50 to 180 µg/m3, and was strongly correlated with outdoors. While the PM2.5 average concentration in workplaces was 60 µg/m3, and it was less affected by outdoor PM2.5 concentration. Passenger's cumulative inhalations in single commuting were about 42 µg and 100 µg when the outdoor PM2.5 concentrations were 20-30 µg/m3 and 120-180 µg/m3, respectively. The PM2.5 inhalation in carriages accounted for the largest proportion of the entire commuting, about 25-40%, because of the longer exposure time and higher PM2.5 concentrations. It is recommended to improve the tightness of the carriage and filter the fresh air to improve the air quality inside. The average daily PM2.5 inhaled by staff was 513.53 µg, which was 5-12 times higher than that of passengers. Installing air purification devices in workplaces and reminding staff to take personal protection can positively protect their health.

Second generation bioethanol potential from selected Malaysia's biodiversity biomasses: A review.

Rising global temperature, worsening air quality and drastic declining of fossil fuel reserve are the inevitable phenomena from the disorganized energy management. Bioethanol is believed to clear out the effects as being an energy-derivable product sourced from renewable organic sources. Second generation bioethanol interests many researches from its unique source of inedible biomass, and this paper presents the potential of several selected biomasses from Malaysia case. As one of countries with rich biodiversity, Malaysia holds enormous potential in second generation bioethanol production from its various agricultural and forestry biomasses, which are the source of lignocellulosic and starch compounds. This paper reviews potentials of biomasses and potential ethanol yield from oil palm, paddy (rice), pineapple, banana and durian, as the common agricultural waste in the country but uncommon to be served as bioethanol feedstock, by calculating the theoretical conversion of cellulose, hemicellulose and starch components of the biomasses into bioethanol. Moreover, the potential of the biomasses as feedstock are discussed based on several reported works.

Cost-benefit analysis and emission reduction of energy efficient lighting at the Universiti Tenaga Nasional.

This paper reports the result of an investigation on the potential energy saving of the lighting systems at selected buildings of the Universiti Tenaga Nasional. The scope of this project includes evaluation of the lighting system in the Library, Admin Building, College of Engineering, College of Information Technology, Apartments, and COE Food court of the university. The main objectives of this project are to design the proper retrofit scenario and to calculate the potential electricity saving, the payback period, and the potential environmental benefits. In this survey the policy for retrofitting the old lighting system with the new energy saving LEDs starts with 10% for the first year and continues constantly for 10 years until all the lighting systems have been replaced. The result of the life cycle analysis reveals that after four years, the selected buildings will bring profit for the investment.

The synthesis and characterization of polymer coated iron oxide microspheres.

For biomedical applications drug carrying polymers are coated around magnetic iron oxide particles to form microspheres. In the present study, the iron oxide powder was ball milled. Microspheres were then synthesized by solvent evaporation, resulting in iron oxide particles encapsulated in a polymer and drug coating. Various parameters, such as the duration of milling and agitation speed as well as the polymer concentration were varied. A milling time of 72 h was found to yield a small size and narrow size distribution of particles; the average particle size was about 600 nm. Measurements of the change in grain size and the magnetic properties of the powder with milling time were performed. It was determined that the size of the microspheres was not sensitive to the initial particle size, but it could be decreased by variation of agitation speed or polymer concentration. The agitation speed and polymer concentration of 400 rpm and 0.04 g poly(l-lactic acid) in 8 g dicholoromethane, respectively, was found to yield small, spherical microspheres with a narrow size distribution. The surface morphology and magnetic properties of the microspheres was also analyzed.