Understanding how junction resistances impact the conduction mechanism in nano-networks.

Networks of nanowires, nanotubes, and nanosheets are important for many applications in printed electronics. However, the network conductivity and mobility are usually limited by the resistance between the particles, often referred to as the junction resistance. Minimising the junction resistance has proven to be challenging, partly because it is difficult to measure. Here, we develop a simple model for electrical conduction in networks of 1D or 2D nanomaterials that allows us to extract junction and nanoparticle resistances from particle-size-dependent DC network resistivity data. We find junction resistances in porous networks to scale with nanoparticle resistivity and vary from 5 Ω for silver nanosheets to 24 GΩ for WS2 nanosheets. Moreover, our model allows junction and nanoparticle resistances to be obtained simultaneously from AC impedance spectra of semiconducting nanosheet networks. Through our model, we use the impedance data to directly link the high mobility of aligned networks of electrochemically exfoliated MoS2 nanosheets (≈ 7 cm2 V-1 s-1) to low junction resistances of ∼2.3 MΩ. Temperature-dependent impedance measurements also allow us to comprehensively investigate transport mechanisms within the network and quantitatively differentiate intra-nanosheet phonon-limited bandlike transport from inter-nanosheet hopping.

Near Room Temperature Production of Segregated Network Composites of Carbon Nanotubes and Regolith as Multifunctional, Extra-Terrestrial Building Materials.

Constructing a semi-permanent base on the moon or Mars will require maximal use of materials found in situ and minimization of materials and equipment transported from Earth. This will mean a heavy reliance on regolith (Lunar or Marian soil) and water, supplemented by small quantities of additives fabricated on Earth. Here it is shown that SiO2-based powders, as well as Lunar and Martian regolith simulants, can be fabricated into building materials at near-ambient temperatures using only a few weight-percent of carbon nanotubes as a binder. These composites have compressive strength and toughness up to 100 MPa and 3 MPa respectively, higher than the best terrestrial concretes. They are electrically conductive (>20 S m-1) and display an extremely large piezoresistive response (gauge factor >600), allowing these composites to be used as internal sensors to monitor the structural health of extra-terrestrial buildings.

Knot Architecture for Biocompatible and Semiconducting 2D Electronic Fiber Transistors.

Wearable devices have generally been rigid due to their reliance on silicon-based technologies, while future wearables will utilize flexible components for example transistors within microprocessors to manage data. Two-dimensional (2D) semiconducting flakes have yet to be investigated in fiber transistors but can offer a route toward high-mobility, biocompatible, and flexible fiber-based devices. Here, the electrochemical exfoliation of semiconducting 2D flakes of tungsten diselenide (WSe2) and molybdenum disulfide (MoS2) is shown to achieve homogeneous coatings onto the surface of polyester fibers. The high aspect ratio (>100) of the flake yields aligned and conformal flake-to-flake junctions on polyester fibers enabling transistors with mobilities µ ≈1 cm2 V-1 s-1 and a current on/off ratio, Ion/Ioff ≈102-104. Furthermore, the cytotoxic effects of the MoS2 and WSe2 flakes with human keratinocyte cells are investigated and found to be biocompatible. As an additional step, a unique transistor 'knot' architecture is created by leveraging the fiber diameter to establish the length of the transistor channel, facilitating a route to scale down transistor channel dimensions (≈100 µm) and utilize it to make a MoS2 fiber transistor with a human hair that achieves mobilities as high as µ ≈15 cm2 V-1 s-1.

Quantitative analysis of printed nanostructured networks using high-resolution 3D FIB-SEM nanotomography.

Networks of solution-processed nanomaterials are becoming increasingly important across applications in electronics, sensing and energy storage/generation. Although the physical properties of these devices are often completely dominated by network morphology, the network structure itself remains difficult to interrogate. Here, we utilise focused ion beam - scanning electron microscopy nanotomography (FIB-SEM-NT) to quantitatively characterise the morphology of printed nanostructured networks and their devices using nanometre-resolution 3D images. The influence of nanosheet/nanowire size on network structure in printed films of graphene, WS2 and silver nanosheets (AgNSs), as well as networks of silver nanowires (AgNWs), is investigated. We present a comprehensive toolkit to extract morphological characteristics including network porosity, tortuosity, specific surface area, pore dimensions and nanosheet orientation, which we link to network resistivity. By extending this technique to interrogate the structure and interfaces within printed vertical heterostacks, we demonstrate the potential of this technique for device characterisation and optimisation.

Mechanical Properties of Conducting Printed Nanosheet Network Thin Films Under Uniaxial Compression.

Thin film networks of solution processed nanosheets show remarkable promise for use in a broad range of applications including strain sensors, energy storage, printed devices, textile electronics, and more. While it is known that their electronic properties rely heavily on their morphology, little is known of their mechanical nature, a glaring omission given the effect mechanical deformation has on the morphology of porous systems and the promise of mechanical post processing for tailored properties. Here, this work employs a recent advance in thin film mechanical testing called the Layer Compression Test to perform the first in situ analysis of printed nanosheet network compression. Due to the well-defined deformation geometry of this unique test, this work is able to explore the out-of-plane elastic, plastic, and creep deformation in these systems, extracting properties of elastic modulus, plastic yield, viscoelasticity, tensile failure and sheet bending vs. slippage under both out of plane uniaxial compression and tension. This work characterizes these for a range of networks of differing porosities and sheet sizes, for low and high compression, as well as the effect of chemical cross linking. This work explores graphene and MoS2 networks, from which the results can be extended to printed nanosheet networks as a whole.

Cobalt Oxide 2D Nanosheets Formed at a Polarized Liquid|Liquid Interface toward High-Performance Li-Ion and Na-Ion Battery Anodes.

Cobalt oxide (Co3O4)-based nanostructures have the potential as low-cost materials for lithium-ion (Li-ion) and sodium-ion (Na-ion) battery anodes with a theoretical capacity of 890 mAh/g. Here, we demonstrate a novel method for the production of Co3O4 nanoplatelets. This involves the growth of flower-like cobalt oxyhydroxide (CoOOH) nanostructures at a polarized liquid|liquid interface, followed by conversion to flower-like Co3O4 via calcination. Finally, sonication is used to break up the flower-like Co3O4 nanostructures into two-dimensional (2D) nanoplatelets with lateral sizes of 20-100 nm. Nanoplatelets of Co3O4 can be easily mixed with carbon nanotubes to create nanocomposite anodes, which can be used for Li-ion and Na-ion battery anodes without any additional binder or conductive additive. The resultant electrodes display impressive low-rate capacities (at 125 mA/g) of 1108 and 1083 mAh/g, for Li-ion and Na-ion anodes, respectively, and stable cycling ability over >200 cycles. Detailed quantitative rate analysis clearly shows that Li-ion-storing anodes charge roughly five times faster than Na-ion-storing anodes.

Solution-Processed Heterojunction Photodiodes Based on WSe2 Nanosheet Networks.

Solution-processed photodetectors incorporating liquid-phase-exfoliated transition metal dichalcogenide nanosheets are widely reported. However, previous studies mainly focus on the fabrication of photoconductors, rather than photodiodes which tend to be based on heterojunctions and are harder to fabricate. Especially, there are rare reports on introducing commonly used transport layers into heterojunctions based on nanosheet networks. In this study, a reliable solution-processing method is reported to fabricate heterojunction diodes with tungsten selenide (WSe2 ) nanosheets as the optical absorbing material and PEDOT: PSS and ZnO as injection/transport-layer materials. By varying the transport layer combinations, the obtained heterojunctions show rectification ratios of up to ≈104 at ±1 V in the dark, without relying on heavily doped silicon substrates. Upon illumination, the heterojunction can be operated in both photoconductor and photodiode modes and displays self-powered behaviors at zero bias.

Transparent Conductors Printed from Grids of Highly Conductive Silver Nanosheets.

Transparent conductors (TCs) represent key components in many applications from optoelectronic devices to electromagnetic shielding. While commercial applications typically use thin films of indium tin oxide, this material is brittle and increasingly scarce, meaning higher performing and cheaper alternatives are sought after. Solution-processible metals would be ideal owing to their high conductivities and printability. However, due to their opacity to visible light, such films need to be very thin to achieve transparency, thus limiting the minimum resistance achievable. One solution is to print metallic particles in a grid structure, which has the advantages of high tunable transparency and resistance at the cost of uniformity. Here, we report silver nanosheets that have been aerosol jet printed into grids as high-performance transparent conductors. We first investigate the effect of annealing on the silver nanosheets where we observe the onset of junction sintering at 160 °C after which the silver network becomes continuous. We then investigate the effect of line width and thickness on the electrical performance and the effect of varying the aperture dimensions on the optical performance. Using these data, we develop simple models, which allow us to optimize the grid and demonstrate a printed transparent conductor with a transmittance of 91% at a sheet resistance of 4.6 Ω/sq.

High Selectivity and Sensitivity in Chemiresistive Sensing of Co(II) Ions with Liquid-Phase Exfoliated Functionalized MoS2 : A Supramolecular Approach.

Chemical sensing of water contamination by heavy metal ions is key as it represents a most severe environmental problem. Liquid-phase exfoliated two-dimensional (2D) transition metal dichalcogenides (TMDs) are suitable candidates for chemical sensing thanks to their high surface-to-volume ratio, sensitivity, unique electrical characteristics, and scalability. However, TMDs lack selectivity due to nonspecific analyte-nanosheet interactions. To overcome this drawback, defect engineering enables controlled functionalization of 2D TMDs. Here, ultrasensitive and selective sensors of cobalt(II) ions via the covalent functionalization of defect-rich MoS2 flakes with a specific receptor, 2,2':6',2″-terpyridine-4'-thiol is developed. A continuous network is assembled by healing of MoS2 sulfur vacancies in a tailored microfluidic approach, enabling high control over the assembly of thin and large hybrid films. The Co2+ cations complexation represents a powerful gauge for low concentrations of cationic species which can be best monitored in a chemiresisitive ion sensor, featuring a 1 pm limit of detection, sensing in a broad concentration range (1 pm - 1 µm) and sensitivity as high as 0.308 ± 0.010 lg([Co2+ ])-1 combined with a high selectivity towards Co2+ over K+ , Ca2+ , Mn2+ , Cu2+ , Cr3+ , and Fe3+ cations. This supramolecular approach based on highly specific recognition can be adapted for sensing other analytes through specific ad-hoc receptors.

Unveiling Charge-Transport Mechanisms in Electronic Devices Based on Defect-Engineered MoS2 Covalent Networks.

Device performance of solution-processed 2D semiconductors in printed electronics has been limited so far by structural defects and high interflake junction resistance. Covalently interconnected networks of transition metal dichalcogenides potentially represent an efficient strategy to overcome both limitations simultaneously. Yet, the charge-transport properties in such systems have not been systematically researched. Here, the charge-transport mechanisms of printed devices based on covalent MoS2 networks are unveiled via multiscale analysis, comparing the effects of aromatic versus aliphatic dithiolated linkers. Temperature-dependent electrical measurements reveal hopping as the dominant transport mechanism: aliphatic systems lead to 3D variable range hopping, unlike the nearest neighbor hopping observed for aromatic linkers. The novel analysis based on percolation theory attributes the superior performance of devices functionalized with π-conjugated molecules to the improved interflake electronic connectivity and formation of additional percolation paths, as further corroborated by density functional calculations. Valuable guidelines for harnessing the charge-transport properties in MoS2 devices based on covalent networks are provided.

High-Mobility Flexible Transistors with Low-Temperature Solution-Processed Tungsten Dichalcogenides.

The investigation of high-mobility two-dimensional (2D) flakes beyond molybdenum disulfide (MoS2) will be necessary to create a library of high-mobility solution-processed networks that conform to substrates and remain functional over thousands of bending cycles. Here we report electrochemical exfoliation of large-aspect-ratio (>100) semiconducting flakes of tungsten diselenide (WSe2) and tungsten disulfide (WS2) as well as MoS2 as a comparison. We use Langmuir-Schaefer coating to achieve highly aligned and conformal flake networks, with minimal mesoporosity (∼2-5%), at low processing temperatures (120 °C) and without acid treatments. This allows us to fabricate electrochemical transistors in ambient air, achieving average mobilities of µMoS2 ≈ 11 cm2 V-1 s-1, µWS2 ≈ 9 cm2 V-1 s-1, and µWSe2 ≈ 2 cm2 V-1 s-1 with a current on/off ratios of Ion/Ioff ≈ 2.6 × 103, 3.4 × 103, and 4.2 × 104 for MoS2, WS2, and WSe2, respectively. Moreover, our transistors display threshold voltages near ∼0.4 V with subthreshold slopes as low as 182 mV/dec, which are essential factors in maintaining power efficiency and represent a 1 order of magnitude improvement in the state of the art. Furthermore, the performance of our WSe2 transistors is maintained on polyethylene terephthalate (PET) even after 1000 bending cycles at 1% strain.

Solution processed, vertically stacked hetero-structured diodes based on liquid-exfoliated WS2 nanosheets: from electrode-limited to bulk-limited behavior.

Vertically stacked metal-semiconductor-metal heterostructures, based on liquid-processed nanomaterials, hold great potential for various printed electronic applications. Here we describe the fabrication of such devices by spray-coating semiconducting tungsten disulfide (WS2) nanosheets onto indium tin oxide (ITO) bottom electrodes, followed by spraying single-walled carbon nanotubes (SWNTs) as the top electrode. Depending on the formulation of the SWNTs ink, we could fabricate either Ohmic or Schottky contacts at the WS2/SWNTs interface. Using isopropanol-dispersed SWNTs led to Ohmic contacts and bulk-limited devices, characterized by out-of-plane conductivities of ∼10-4 S m-1. However, when aqueous SWNTs inks were used, rectification was observed, due to the formation of a doping-induced Schottky barrier at the WS2/SWNTs interface. For thin WS2 layers, such devices were characterized by a barrier height of ∼0.56 eV. However, increasing the WS2 film thickness led to increased series resistance, leading to a change-over from electrode-limited to bulk-limited behavior at a transition thickness of ∼2.6 µm. This work demonstrates that Ohmic/Schottky behavior is tunable and lays the foundation for fabricating large-area 2D nanosheet-based solution-deposited devices and stacks.

Liquid Processing of Interfacially Grown Iron-Oxide Flowers into 2D-Platelets Yields Lithium-Ion Battery Anodes with Capacities of Twice the Theoretical Value.

Iron oxide (Fe2 O3 ) is an abundant and potentially low-cost material for fabricating lithium-ion battery anodes. Here, the growth of α-Fe2 O3 nano-flowers at an electrified liquid-liquid interface is demonstrated. Sonication is used to convert these flowers into quasi-2D platelets with lateral sizes in the range of hundreds of nanometers and thicknesses in the range of tens of nanometers. These nanoplatelets can be combined with carbon nanotubes to form porous, conductive composites which can be used as electrodes in lithium-ion batteries. Using a standard activation process, these anodes display good cycling stability, reasonable rate performance and low-rate capacities approaching 1500 mAh g-1 , consistent with the current state-of-the-art for Fe2 O3 . However, by using an extended activation process, it is found that the morphology of these composites can be significantly changed, rendering the iron oxide amorphous and significantly increasing the porosity and internal surface area. These morphological changes yield anodes with very good cycling stability and low-rate capacity exceeding 2000 mAh g-1 , which is competitive with the best anode materials in the literature. However, the data implies that, after activation, the iron oxide displays a reduced solid-state lithium-ion diffusion coefficient resulting in somewhat degraded rate performance.

Liquid-Phase Exfoliation of Nonlayered Non-Van-Der-Waals Crystals into Nanoplatelets.

For nearly 15 years, researchers have been using liquid-phase exfoliation (LPE) to produce 2D nanosheets from layered crystals. This has yielded multiple 2D materials in a solution-processable form whose utility has been demonstrated in multiple applications. It was believed that the exfoliation of such materials is enabled by the very large bonding anisotropy of layered materials where the strength of intralayer chemical bonds is very much larger than that of interlayer van der Waals bonds. However, over the last five years, a number of papers have raised questions about our understanding of exfoliation by describing the LPE of nonlayered materials. These results are extremely surprising because, as no van der Waals gap is present to provide an easily cleaved direction, the exfoliation of such compounds requires the breaking of only chemical bonds. Here the progress in this unexpected new research area is examined. The structure and properties of nanoplatelets produced by LPE of nonlayered materials are reviewed. A number of unexplained trends are found, not least the preponderance of isotropic materials that have been exfoliated to give high-aspect-ratio nanoplatelets. Finally, the applications potential of this new class of 2D materials are considered.

Highly Conductive Networks of Silver Nanosheets.

Although printed networks of semiconducting nanosheets have found success in a range of applications, conductive nanosheet networks are limited by low conductivities (<106 S m-1 ). Here, dispersions of silver nanosheets (AgNS) that can be printed into highly conductive networks are described. Using a commercial thermal inkjet printer, AgNS patterns with unannealed conductivities of up to (6.0 ± 1.1) × 106  S m-1 are printed. These networks can form electromagnetic interference shields with record shielding effectiveness of >60 dB in the microwave region at thicknesses <200 nm. High resolution patterns with line widths down to 10 µm are also printed using an aerosol-jet printer which, when annealed at 200 °C, display conductivity >107  S m-1 . Unlike conventional Ag-nanoparticle inks, the 2D geometry of AgNS yields smooth, short-free interfaces between electrode and active layer when used as the top electrode in vertical nanosheet heterostructures. This shows that all-printed vertical heterostructures of AgNS/WS2 /AgNS, where the top electrode is a mesh grid, function as photodetectors demonstrating that such structures can be used in optoelectronic applications that usually require transparent conductors.

Quantifying the Piezoresistive Mechanism in High-Performance Printed Graphene Strain Sensors.

Printed strain sensors will be important in applications such as wearable devices, which monitor breathing and heart function. Such sensors need to combine high sensitivity and low resistance with other factors such as cyclability, low hysteresis, and minimal frequency/strain-rate dependence. Although nanocomposite sensors can display a high gauge factor (G), they often perform poorly in the other areas. Recently, evidence has been growing that printed, polymer-free networks of nanoparticles, such as graphene nanosheets, display very good all-round sensing performance, although the details of the sensing mechanism are poorly understood. Here, we perform a detailed characterization of the thickness dependence of piezoresistive sensors based on printed networks of graphene nanosheets. We find both conductivity and gauge factor to display percolative behavior at low network thickness but bulk-like behavior for networks above ∼100 nm thick. We use percolation theory to derive an equation for gauge factor as a function of network thickness, which well-describes the observed thickness dependence, including the divergence in gauge factor as the percolation threshold is approached. Our analysis shows that the dominant contributor to the sensor performance is not the effect of strain on internanosheet junctions but the strain-induced modification of the network structure. Finally, we find these networks display excellent cyclability, hysteresis, and frequency/strain-rate dependence as well as gauge factors as high as 350.

Additive Manufacturing of Ti3 C2 -MXene-Functionalized Conductive Polymer Hydrogels for Electromagnetic-Interference Shielding.

The ongoing miniaturization of devices and development of wireless and implantable technologies demand electromagnetic interference (EMI)-shielding materials with customizability. Additive manufacturing of conductive polymer hydrogels with favorable conductivity and biocompatibility can offer new opportunities for EMI-shielding applications. However, simultaneously achieving high conductivity, design freedom, and shape fidelity in 3D printing of conductive polymer hydrogels is still very challenging. Here, an aqueous Ti3 C2 -MXene-functionalized poly(3,4-ethylenedioxythiophene):polystyrene sulfonate ink is developed for extrusion printing to create 3D objects with arbitrary geometries, and a freeze-thawing protocol is proposed to transform the printed objects directly into highly conductive and robust hydrogels with high shape fidelity on both the macro- and microscale. The as-obtained hydrogel exhibits a high conductivity of 1525.8 S m-1 at water content up to 96.6 wt% and also satisfactory mechanical properties with flexibility, stretchability, and fatigue resistance. Furthermore, the use of the printed hydrogel for customizable EMI-shielding applications is demonstrated. The proposed easy-to-manufacture approach, along with the highlighted superior properties, expands the potential of conductive polymer hydrogels in future customizable applications and represents a real breakthrough from the current state of the art.

Highly Sensitive Composite Foam Bodily Sensors Based on the g-Putty Ink Soaking Procedure.

Electrically conductive composite materials are highlighted as a potential tech path toward future flexible devices for wearable health technologies. To be commercially viable, these materials must not only be mechanically soft, highly sensitive to deformation, and report a sustainable signal but also utilize manufacturing methods that facilitate large-scale production. An ideal candidate for these envisioned technologies is the viscous, electromechanically sensitive composite material g-putty. Inks based on g-putty here are shown to transform a commercial polymer foam into a sensitive strain sensing material through a simple, scalable soaking procedure. Foam composites reported here have sensitives as high as ∼20 in terms of compressive strain and ∼0.4 kPa-1 with respect to applied compressive stress; both values being comparable to the parent g-putty material. Through g-putty's self-adhering nature, the foams used acted as an elastic scaffolding that aided in overcoming many of the hysteresis effects associated with g-putty without the need for further encapsulation methods. From this, these composite foams were demonstrated to have a sustainable signal that allowed for effective impact and vital sign sensing.

Printable G-Putty for Frequency- and Rate-Independent, High-Performance Strain Sensors.

While nanocomposite electromechanical sensors are expected to display reasonable conductivity and high sensitivity, little consideration is given to eliminating hysteresis and strain rate/frequency dependence from their response. For example, while G-putty, a composite of graphene and polysiloxane, has very high electromechanical sensitivity, its extreme viscoelasticity renders it completely unsuitable for real sensors due to hysteretic and rate-/frequency-dependent effects. Here it is shown that G-putty can be converted to an ink and printed into patterned thin films on elastic substrates. A partial graphene-polymer phase segregation during printing increases the thin-film conductivity by ×106 compared to bulk, while the mechanical effects of the substrate largely suppress hysteresis and completely remove strain rate and frequency dependence. This allows the fabrication of practical, high-gauge-factor, wearable sensors for pulse measurements as well as patterned sensors for low-signal vibration sensing.