Additive Manufacturing of Transparent Multi-Component Nanoporous Glasses.

Fabrication of glass with complex geocd the low resolution of particle-based or fused glass technologies. Herein, a high-resolution 3D printing of transparent nanoporous glass is presented, by the combination of transparent photo-curable sol-gel printing compositions and digital light processing (DLP) technology. Multi-component glass, including binary (Al2 O3 -SiO2 ), ternary (ZnO-Al2 O3 -SiO2 , TiO2 -Al2 O3 -SiO2 ), and quaternary oxide (CaO-P2 O5 -Al2 O3 -SiO2 ) nanoporous glass objects with complex shapes, high spatial resolutions, and multi-oxide chemical compositions are fabricated, by DLP printing and subsequent sintering process. The uniform nanopores of Al2 O3 -SiO2 -based nanoporous glasses with the diameter (≈6.04 nm), which is much smaller than the visible light wavelength, result in high transmittance (>95%) at the visible range. The high surface area of printed glass objectives allows post-functionalization via the adsorption of functional guest molecules. The photoluminescence and hydrophobic modification of 3D printed glass objectives are successfully demonstrated. This work extends the scope of 3D printing to transparent nanoporous glasses with complex geometry and facile functionalization, making them available for a wide range of applications.

Reaching silicon-based NEMS performances with 3D printed nanomechanical resonators.

The extreme miniaturization in NEMS resonators offers the possibility to reach an unprecedented resolution in high-performance mass sensing. These very low limits of detection are related to the combination of two factors: a small resonator mass and a high quality factor. The main drawback of NEMS is represented by the highly complex, multi-steps, and expensive fabrication processes. Several alternatives fabrication processes have been exploited, but they are still limited to MEMS range and very low-quality factor. Here we report the fabrication of rigid NEMS resonators with high-quality factors by a 3D printing approach. After a thermal step, we reach complex geometry printed devices composed of ceramic structures with high Young's modulus and low damping showing performances in line with silicon-based NEMS resonators ones. We demonstrate the possibility of rapid fabrication of NEMS devices that present an effective alternative to semiconducting resonators as highly sensitive mass and force sensors.

3D Printing of Micrometer-Sized Transparent Ceramics with On-Demand Optical-Gain Properties.

Transparent ceramics are usually polycrystalline materials, which are wildly used in many optical applications, such as lasers. As of today, the fabrication of transparent ceramic structures is still limited to conventional fabrication methods, which do not enable the formation of complex structures. A new approach for 3D printing of micrometer-size, transparent ceramic structures is presented. By using a solution of metal salts that can undergo a sol-gel process and photopolymerization by two-photon printing, micrometer-sized yttrium aluminum garnet (YAG) structures doped with neodymium (Nd) are fabricated. The resulting structures are not only transparent in the visible spectrum but can also emit light at 1064 nm due to the doping with Nd. By using solution-based precursors, without any particles, the sintering can be performed under air at ambient pressure and at a relatively low temperature, compared to conventional processes for YAG. The crystalline structure is imaged at atomic resolution by ultrahigh-resolution scanning transmission electron microscopy (STEM), indicating that the doped Nd atoms are located at the yttrium positions. Such miniaturized structures can be used for diverse applications, e.g., optical components in high-intensity laser systems, which require heat resistance, or as light sources in optical circuits.

3D-Printed Organic-Ceramic Complex Hybrid Structures with High Silica Content.

Hybrid organic-inorganic sol gel inks that can undergo both condensation and radical polymerization are developed, enabling fabrication of complex objects by additive manufacturing technology, yielding 3D objects with superior properties. The 3D objects have very high silica content and are printed by digital light processing commercial printers. The printed lightweight objects are characterized by excellent mechanical strength compared to currently used high-performance polymers (139 MPa), very high stability at elevated temperatures (heat deflection temperature >270 °C), high transparency (89%), and lack of cracks, with glossiness similar to silica glasses. The new inks fill the gap in additive manufacturing of objects composed of ceramics only and organic materials only, thus enabling harnessing the advantages of both worlds of materials.

Additive Manufacturing of Transparent Silica Glass from Solutions.

A sol, aqueous solution-based ink is presented for fabrication of 3D transparent silica glass objects with complex geometries, by a simple 3D printing process conducted at room temperature. The ink combines a hybrid ceramic precursor that can undergo both the photopolymerization reaction and a sol-gel process, both in the solution form, without any particles. The printing is conducted by localized photopolymerization with the use of a low-cost 3D printer. Following printing, upon aging and densifying, the resulting objects convert from a gel to a xerogel and then to a fused silica. The printed objects, which are composed of fused silica, are transparent and have tunable density and refractive indices.

3D Printing: 3D Printing of Shape Memory Polymers for Flexible Electronic Devices (Adv. Mater. 22/2016).

On page 4449, D. Cohn, S. Magdassi, and co-workers describe a general and facile method based on 3D printing of methacrylated macromonomers to fabricate shape-memory objects that can be used in flexible and responsive electrical circuits. Such responsive objects can be used in the fabrication of soft robotics, minimal invasive medical devices, sensors, and wearable electronics. The use of 3D printing overcomes the poor processing characteristics of thermosets and enables complex geometries that are not easily accessible by other techniques.

High-performance 3D printing of hydrogels by water-dispersible photoinitiator nanoparticles.

In the absence of water-soluble photoinitiators with high absorbance in the ultraviolet (UV)-visible range, rapid three-dimensional (3D) printing of hydrogels for tissue engineering is challenging. A new approach enabling rapid 3D printing of hydrogels in aqueous solutions is presented on the basis of UV-curable inks containing nanoparticles of highly efficient but water-insoluble photoinitiators. The extinction coefficient of the new water-dispersible nanoparticles of 2,4,6-trimethylbenzoyl-diphenylphosphine oxide (TPO) is more than 300 times larger than the best and most used commercially available water-soluble photoinitiator. The TPO nanoparticles absorb significantly in the range from 385 to 420 nm, making them suitable for use in commercially available, low-cost, light-emitting diode-based 3D printers using digital light processing. The polymerization rate at this range is very fast and enables 3D printing that otherwise is impossible to perform without adding solvents. The TPO nanoparticles were prepared by rapid conversion of volatile microemulsions into water-dispersible powder, a process that can be used for a variety of photoinitiators. Such water-dispersible photoinitiator nanoparticles open many opportunities to enable rapid 3D printing of structures prepared in aqueous solutions while bringing environmental advantages by using low-energy curing systems and avoiding the need for solvents.

3D Printing of Shape Memory Polymers for Flexible Electronic Devices.

The formation of 3D objects composed of shape memory polymers for flexible electronics is described. Layer-by-layer photopolymerization of methacrylated semicrystalline molten macromonomers by a 3D digital light processing printer enables rapid fabrication of complex objects and imparts shape memory functionality for electrical circuits.