Complex Resonant Scattering Behavior in the Surface Plasmon Resonance Imaging Microscopy of Single Gold Nanorods.

Diffraction patterns observed in surface plasmon resonance imaging (SPRI) microscopy measurements of single gold nanorods (AuNRs) exhibit a complex behavior at wavelengths near the longitudinal plasmonic resonance band. SPRI microscopy measurements at 814 nm from AuNRs in three samples with resonance extinction maxima at 670, 816, and 980 nm reveal a variety of diffraction patterns with central peaks that are either positive, negative, or biphasic. A unitless ratio parameter MR (-1 ≤ MR ≤ 1) is created to describe the distribution of diffraction patterns. A purely negative (MR = -1) central peak is observed for 30%, 57%, and 98% of the diffraction patterns in the 670, 816, and 980 nm samples, respectively. These results along with a theoretical modeling of the diffraction patterns with an anisotropic complex scattering coefficient suggests that this behavior only occurs for AuNRs when the laser wavelength used in SPRI experiments is shorter than the AuNR plasmonic resonance maxima, that is, in the anomalous dispersion region.

MicroRNA detection on microsensor arrays by SPR imaging measurements with enzymatic signal enhancement.

We investigated sequence-specific and simultaneous microRNA (miRNA) detections by surface plasmon resonance (SPR) imaging measurements on SPR chips possessing an Au spot array modified with probe DNAs based on a miRNA-detection-selective SPR signal amplification method. MiRNAs were detected with the detection limit of the attomole level by SPR imaging measurements for different miRNA concentrations on a single chip. SPR signals were enhanced based on a combination process of sequence-specific hybridization of the miRNA to the probe DNAs, extension reaction of polyadenine (poly(A)) tails by poly(A) polymerase, binding of a ternary complex of T30-biotin/horseradish peroxidase (HRP)-biotin/streptavidin to the poly(A) tails, and the oxidation reaction of tetramethylbenzidine (TMB) on the HRP by providing a blue precipitate on the surface. This process sequence-specifically and dramatically amplified the SPR signals. This is a simple, cost-effective, and feasible signal amplification method based on the organic compound TMB instead of metal nanoparticles.

Particle sensing with confined optical field enhanced fluorescence emission (Cofefe).

We describe the development and performance of a new type of optical sensor suitable for registering the binding/dissociation of nanoscopic particles near a gold sensing surface. The method shares similarities with surface plasmon resonance microscopy but uses a completely different optical signature for reading out binding events. This new optical read-out mechanism, which we call confined optical field enhanced fluorescence emission (Cofefe), uses pulsed surface plasmon polariton fields at the gold/liquid interface that give rise to confined optical fields upon binding of the target particle to the gold surface. The confined near-fields are sufficient to induce two-photon absorption in the gold sensor surface near the binding site. Subsequent radiative recombination of the electron-hole pairs in the gold produces fluorescence emission, which can be captured by a camera in the far-field. Bound nanoparticles show up as bright confined spots against a dark background on the camera. We show that the Cofefe sensor is capable of detecting gold and silicon nanoparticles, as well as polymer nanospheres and sub-µm lipid droplets in a label-free manner with average illumination powers of less than 10 µW/µm2.

Characterizing Single Polymeric and Protein Nanoparticles with Surface Plasmon Resonance Imaging Measurements.

Near-infrared surface plasmon resonance imaging (SPRI) microscopy is used to detect and characterize the adsorption of single polymeric and protein nanoparticles (PPNPs) onto chemically modified gold thin films in real time. The single-nanoparticle SPRI responses, Δ%RNP, from several hundred adsorbed nanoparticles are collected in a single SPRI adsorption measurement. Analysis of Δ%RNP frequency distribution histograms is used to provide information on the size, material content, and interparticle interactions of the PPNPs. Examples include the measurement of log-normal Δ%RNP distributions for mixtures of polystyrene nanoparticles, the quantitation of bioaffinity uptake into and aggregation of porous NIPAm-based (N-isopropylacrylamide) hydrogel nanoparticles specifically engineered to bind peptides and proteins, and the characterization of the negative single-nanoparticle SPRI response and log-normal Δ%RNP distributions obtained for three different types of genetically encoded gas-filled protein nanostructures derived from bacteria.

Fabrication of PEDOT Nanocone Arrays with Electrochemically Modulated Broadband Antireflective Properties.

Ordered nanocone arrays of the electroactive polymer poly(3,4-ethylenedioxythiophene) (PEDOT) were fabricated by the simultaneous oxygen plasma etching of an electrodeposited PEDOT thin film coated with a hexagonally closed packed polystyrene bead monolayer. PEDOT nanocone arrays with an intercone spacing of 200 nm and an average nanocone height of 350 nm exhibited a low broadband reflectivity of <1.5% from 550 to 800 nm. Electrochemical modulation of the oxidation state of the PEDOT nanocone array film was used to change both its ex situ absorption spectrum (electrochromism) and reflection spectrum (electroreflectivity). The sign of the PEDOT nanocone array electroreflectivity was opposite to that observed from unmodified PEDOT thin films; this significant difference is attributed to the unique optical behavior of nanostructured surfaces with an interfacial layer that contains a graded mix of air and highly absorptive nanocones. The combined electrochromic and electroreflective behavior of the antireflective PEDOT nanocone array films should find promising applications in solar energy cells, sensors and other optical devices.

A Microwell-Printing Fabrication Strategy for the On-Chip Templated Biosynthesis of Protein Microarrays for Surface Plasmon Resonance Imaging.

A two-step templated, ribosomal biosynthesis/printing method for the fabrication of protein microarrays for surface plasmon resonance imaging (SPRI) measurements is demonstrated. In the first step, a sixteen component microarray of proteins is created in microwells by cell free on chip protein synthesis; each microwell contains both an in vitro transcription and translation (IVTT) solution and 350 femtomoles of a specific DNA template sequence that together are used to create approximately 40 picomoles of a specific hexahistidine-tagged protein. In the second step, the protein microwell array is used to contact print one or more protein microarrays onto nitrilotriacetic acid (NTA)-functionalized gold thin film SPRI chips for real-time SPRI surface bioaffinity adsorption measurements. Even though each microwell array element only contains approximately 40 picomoles of protein, the concentration is sufficiently high for the efficient bioaffinity adsorption and capture of the approximately 100 femtomoles of hexahistidine-tagged protein required to create each SPRI microarray element. As a first example, the protein biosynthesis process is verified with fluorescence imaging measurements of a microwell array containing His-tagged green fluorescent protein (GFP), yellow fluorescent protein (YFP) and mCherry (RFP), and then the fidelity of SPRI chips printed from this protein microwell array is ascertained by measuring the real-time adsorption of various antibodies specific to these three structurally related proteins. This greatly simplified two-step synthesis/printing fabrication methodology eliminates most of the handling, purification and processing steps normally required in the synthesis of multiple protein probes, and enables the rapid fabrication of SPRI protein microarrays from DNA templates for the study of protein-protein bioaffinity interactions.

Measuring melittin uptake into hydrogel nanoparticles with near-infrared single nanoparticle surface plasmon resonance microscopy.

This paper describes how changes in the refractive index of single hydrogel nanoparticles (HNPs) detected with near-infrared surface plasmon resonance microscopy (SPRM) can be used to monitor the uptake of therapeutic compounds for potential drug delivery applications. As a first example, SPRM is used to measure the specific uptake of the bioactive peptide melittin into N-isopropylacrylamide (NIPAm)-based HNPs. Point diffraction patterns in sequential real-time SPRM differential reflectivity images are counted to create digital adsorption binding curves of single 220 nm HNPs from picomolar nanoparticle solutions onto hydrophobic alkanethiol-modified gold surfaces. For each digital adsorption binding curve, the average single nanoparticle SPRM reflectivity response, ⟨Δ%RNP⟩, was measured. The value of ⟨Δ%RNP⟩ increased linearly from 1.04 ± 0.04 to 2.10 ± 0.10% when the melittin concentration in the HNP solution varied from zero to 2.5 µM. No change in the average HNP size in the presence of melittin is observed with dynamic light scattering measurements, and no increase in ⟨Δ%RNP⟩ is observed in the presence of either FLAG octapeptide or bovine serum albumin. Additional bulk fluorescence measurements of melittin uptake into HNPs are used to estimate that a 1% increase in ⟨Δ%RNP⟩ observed in SPRM corresponds to the incorporation of approximately 65000 molecules into each 220 nm HNP, corresponding to roughly 4% of its volume. The lowest detected amount of melittin loading into the 220 nm HNPs was an increase in ⟨Δ%RNP⟩ of 0.15%, corresponding to the absorption of 10000 molecules.

Surface Enzyme Chemistries for Ultrasensitive Microarray Biosensing with SPR Imaging.

The sensitivity and selectivity of surface plasmon resonance imaging (SPRI) biosensing with nucleic acid microarrays can be greatly enhanced by exploiting various nucleic acid ligases, nucleases, and polymerases that manipulate the surface-bound DNA and RNA. We describe here various examples from each of these different classes of surface enzyme chemistries that have been incorporated into novel detection strategies that either drastically enhance the sensitivity of or create uniquely selective methods for the SPRI biosensing of proteins and nucleic acids. A dual-element generator-detector microarray approach that couples a bioaffinity adsorption event on one microarray element to nanoparticle-enhanced SPRI measurements of nucleic acid hybridization adsorption on a different microarray element is used to quantitatively detect DNA, RNA, and proteins at femtomolar concentrations. Additionally, this dual-element format can be combined with the transcription and translation of RNA from surface-bound double-stranded DNA (dsDNA) templates for the on-chip multiplexed biosynthesis of aptamer and protein microarrays in a microfluidic format; these microarrays can be immediately used for real-time SPRI bioaffinity sensing measurements.

Shrink-induced silica multiscale structures for enhanced fluorescence from DNA microarrays.

We describe a manufacturable and scalable method for fabrication of multiscale wrinkled silica (SiO2) structures on shrink-wrap film to enhance fluorescence signals in DNA fluorescence microarrays. We are able to enhance the fluorescence signal of hybridized DNA by more than 120 fold relative to a planar glass slide. Notably, our substrate has improved detection sensitivity (280 pM) relative to planar glass slide (11 nM). Furthermore, this is accompanied by a 30-45 times improvement in the signal-to-noise ratio (SNR). Unlike metal enhanced fluorescence (MEF) based enhancements, this is a far-field and uniform effect based on surface concentration and photophysical effects from the nano- to microscale SiO2 structures. Notably, the photophysical effects contribute an almost 2.5 fold enhancement over the concentration effects alone. Therefore, this simple and robust method offers an efficient technique to enhance the detection capabilities of fluorescence based DNA microarrays.

Flexible Teflon nanocone array surfaces with tunable superhydrophobicity for self-cleaning and aqueous droplet patterning.

Tunable hydrophobic/hydrophilic flexible Teflon nanocone array surfaces were fabricated over large areas (cm(2)) by a simple two-step method involving the oxygen plasma etching of a colloidal monolayer of polystyrene beads on a Teflon film. The wettability of the nanocone array surfaces was controlled by the nanocone array dimensions and various additional surface modifications. The resultant Teflon nanocone array surfaces were hydrophobic and adhesive (a "gecko" type of surface on which a water droplet has a high contact angle but stays in place) with a contact angle that correlated with the aspect ratio/sharpness of the nanocones. The surfaces switched to a superhydrophobic or "lotus" type of surface when hierarchical nanostructures were created on Teflon nanocones by modifying them with a gold nanoparticle (AuNPs) film. The nanocone array surfaces could be made superhydrophobic with a maximum contact angle of 160° by the further modification of the AuNPs with an octadecanethiol (C18SH) monolayer. Additionally, these nanocone array surfaces became hydrophilic when the nanocone surfaces were sequentially modified with AuNPs and hydrophilic polydopamine (PDA) layers. The nanocone array surfaces were tested for two potential applications: self-cleaning superhydrophobic surfaces and for the passive dispensing of aqueous droplets onto hybrid superhydrophobic/hydrophilic microarrays.

Silica nanowire arrays for diffraction-based bioaffinity sensing.

Arrays of electrodeposited silica nanowires (SiO2 NWs) have been fabricated over large areas (cm(2)) on fluoropolymer thin films attached to glass substrates by a combination of photolithography and electrochemically triggered sol-gel nanoscale deposition. Optical and scanning electron microscopy (SEM) measurements revealed that the SiO2 NW arrays had an average spacing of ten micrometers and an average width of 700 nm with a significant grain structure that was a result of the sol-gel deposition process. The optical diffraction properties at 633 nm of the SiO2 NW arrays were characterized when placed in contact with solutions by using a prism-coupled total internal reflection geometry; quantification of changes in these diffraction properties was applied in various sensing applications. Bulk refractive index sensing by using the SiO2 NW grating was demonstrated with a sensitivity of 1.30×10(-5) RIU. Toposelectively chemically modified SiO2 NW arrays were used for diffraction biosensing measurements of surface binding events, such as the electrostatic adsorption of gold nanoparticles and the bioaffinity adsorption of streptavidin onto a biotin monolayer. Finally, the application of the SiO2 NW arrays for practical medical-diagnostic applications was demonstrated by monitoring the diffraction of SiO2 NW arrays functionalized with a single-stranded (ss)DNA aptamer to detect human α-thrombin from solutions at sub-pathologic nanomolar concentrations.

Single-nanoparticle near-infrared surface plasmon resonance microscopy for real-time measurements of DNA hybridization adsorption.

A novel 814 nm near-infrared surface plasmon resonance (SPR) microscope is used for the real-time detection of the sequence-selective hybridization adsorption of single DNA-functionalized gold nanoparticles. The objective-coupled, high numerical aperture SPR microscope is capable of imaging in situ the adsorption of single polystyrene and gold particles with diameters ranging from 450 to 20 nm onto a 90 µm × 70 µm area of a gold thin film with a time resolution of approximately 1-3 s. Initial real-time SPR imaging (SPRI) measurements were performed to detect the accumulation of 40 nm gold nanoparticles for 10 min onto a gold thin film functionalized with a 100% complementary DNA surface at concentrations from 5 pM to 100 fM by counting individual particle binding events. A 100% noncomplementary DNA surface exhibited virtually no nanoparticle adsorption. In contrast, in a second set of SPRI measurements, two component complementary/noncomplementary mixed DNA monolayers that contained a very small percentage of complementary sequences ranging from 0.1 to 0.001%, showed both permanent and transient hybridization adsorption of the gold nanoparticles that could be tracked both temporally and spatially with the SPR microscope. These experiments demonstrate that SPR imaging measurements of single biofunctionalized nanoparticles can be incorporated into bioaffinity biosensing methods at subpicomolar concentrations.

Lithographically Patterned Nanoscale Electrodeposition of Plasmonic, Bimetallic, Semiconductor, Magnetic, and Polymer Nanoring Arrays.

Large area arrays of magnetic, semiconducting, and insulating nanorings were created by coupling colloidal lithography with nanoscale electrodeposition. This versatile nanoscale fabrication process allows for the independent tuning of the spacing, diameter, and width of the nanorings with typical values of 1.0 µm, 750 nm, and 100 nm, respectively, and was used to form nanorings from a host of materials: Ni, Co, bimetallic Ni/Au, CdSe, and polydopamine. These nanoring arrays have potential applications in memory storage, optical materials, and biosensing. A modified version of this nanoscale electrodeposition process was also used to create arrays of split gold nanorings. The size of the split nanoring opening was controlled by the angle of photoresist exposure during the fabrication process and could be varied from 50% down to 10% of the ring circumference. The large area (cm2 scale) gold split nanoring array surfaces exhibited strong polarization-dependent plasmonic absorption bands for wavelengths from 1 to 5 µm. Plasmonic nanoscale split ring arrays are potentially useful as tunable dichroic materials throughout the infrared and near-infrared spectral regions.

Fabrication of broadband antireflective plasmonic gold nanocone arrays on flexible polymer films.

Flexible broadband antireflective and light-absorbing nanostructured gold thin films are fabricated by gold vapor deposition onto Teflon films modified with nanocone arrays. The nanostructures are created by the oxygen plasma etching of polystyrene bead monolayers on Teflon surfaces. The periodicity and height of the nanocone arrays are controlled by the bead diameter and the overall etching time. The gold nanocone arrays exhibit a reflectivity of less than 1% over a wide spectral range (450-900 nm) and a wide range of incident angles (0-70°); this unique optical response is attributed to a combination of diffractive scattering loss and localized plasmonic absorption. In addition to nanocones, periodic nanostructures of nanocups, nanopyramids, and nanocavities can be created by the plasma etching of colloidal bilayers. This fabrication method can be used to create flexible nanocone-structured gold thin films over large surface areas (cm(2)) and should be rapidly incorporated into new technological applications that require wide-angle and broadband antireflective coatings.

Electrodeposition of polydopamine thin films for DNA patterning and microarrays.

The controlled electrodeposition of functional polydopamine (PDA) thin films from aqueous dopamine solutions is demonstrated with a combination of electrochemistry, atomic force microscopy (AFM), and surface plasmon resonance (SPR) measurements. PDA micropatterns are then fabricated by electrodeposition on micrometer length scale gold electrodes and used for attaching amino-modified single-stranded DNA (ssDNA). After hybridization with fluorescently labeled ssDNA, the fluorescence microscopy characterization reveals that: (i) PDA can be toposelectively deposited at the microscale and (ii) electrochemically deposited PDA can be functionalized with amino-terminated ssDNA using the same chemistry as that for spontaneously deposited PDA. Finally, the application of electrodeposited PDA thin films to fabricate ssDNA microarrays is reported using SPR imaging (SPRI) measurements for the detection of DNA and DNA-modified gold nanoparticles.

Fabrication of DNA microarrays on polydopamine-modified gold thin films for SPR imaging measurements.

Polydopamine (PDA) films were fabricated on thin film gold substrates in a single-step polymerization-deposition process from dopamine solutions and then employed in the construction of robust DNA microarrays for the ultrasensitive detection of biomolecules with nanoparticle-enhanced surface plasmon resonance (SPR) imaging. PDA multilayers with thicknesses varying from 1 to 5 nm were characterized with a combination of scanning angle SPR and AFM experiments, and 1.3 ± 0.2 nm PDA multilayers were chosen as an optimal thickness for the SPR imaging measurements. DNA microarrays were then fabricated by the reaction of amine-functionalized single-stranded DNA (ssDNA) oligonucleotides with PDA-modified gold thin film microarray elements, and were subsequently employed in SPR imaging measurements of DNA hybridization adsorption and protein-DNA binding. Concurrent control experiments with non-complementary ssDNA sequences demonstrated that the adhesive PDA multilayer was also able to provide good resistance to the nonspecific binding of biomolecules. Finally, a series of SPR imaging measurements of the hybridization adsorption of DNA-modified gold nanoparticles onto mixed sequence DNA microarrays were used to confirm that the use of PDA multilayer films is a simple, rapid, and versatile method for fabricating DNA microarrays for ultrasensitive nanoparticle-enhanced SPR imaging biosensing.

Entrapment of bed bugs by leaf trichomes inspires microfabrication of biomimetic surfaces.

Resurgence in bed bug infestations and widespread pesticide resistance have greatly renewed interest in the development of more sustainable, environmentally friendly methods to manage bed bugs. Historically, in Eastern Europe, bed bugs were entrapped by leaves from bean plants, which were then destroyed; this purely physical entrapment was related to microscopic hooked hairs (trichomes) on the leaf surfaces. Using scanning electron microscopy and videography, we documented the capture mechanism: the physical impaling of bed bug feet (tarsi) by these trichomes. This is distinct from a Velcro-like mechanism of non-piercing entanglement, which only momentarily holds the bug without sustained capture. Struggling, trapped bed bugs are impaled by trichomes on several legs and are unable to free themselves. Only specific, mechanically vulnerable locations on the bug tarsi are pierced by the trichomes, which are located at effective heights and orientations for bed bug entrapment despite a lack of any evolutionary association. Using bean leaves as templates, we microfabricated surfaces indistinguishable in geometry from the real leaves, including the trichomes, using polymers with material properties similar to plant cell walls. These synthetic surfaces snag the bed bugs temporarily but do not hinder their locomotion as effectively as real leaves.

DNAzyme footprinting: detecting protein-aptamer complexation on surfaces by blocking DNAzyme cleavage activity.

A novel method to quantitatively measure the binding of proteins to single-stranded DNA (ssDNA) aptamers that employs the inhibition of the DNAzyme hydrolysis of aptamer monolayers is described. A 28-base DNAzyme was designed to specifically bind to and cleave a 29-base ssDNA sequence that can fold into a G-quartet aptamer and bind the protein thrombin. The binding strength of the DNAzyme to the aptamer sequence was designed to be less than the binding strength of the thrombin to the aptamer (ΔG° = -43.1 and -51.8 kJ/mol, respectively). Formation of the thrombin-aptamer complex was found to block DNAzyme cleavage activity both in solution and in an ssDNA aptamer monolayer. We denote this method for detecting protein-aptamer complexation as "DNAzyme footprinting" in analogy to the process of DNase footprinting for the detection of protein-DNA interactions. By attaching a 40-base reporter sequence to the ssDNA aptamer monolayer, the detection of any protein-aptamer complexes remaining on the surface after DNAzyme activity can be greatly enhanced (down to one thrombin-aptamer complex per 10,000 ssDNA molecules corresponding to 100 fM thrombin in solution) by a subsequent surface RNA transcription amplification reaction followed by RNA detection with nanoparticle-enhanced SPR imaging. In addition to RNA transcription, DNAzyme footprinting can be coupled to a wide variety of other nucleic acid surface amplification schemes and thus is a powerful new route for the enzymatically amplified detection of proteins via protein-aptamer complex formation.

Lithographically patterned electrodeposition of gold, silver, and nickel nanoring arrays with widely tunable near-infrared plasmonic resonances.

A novel low-cost nanoring array fabrication method that combines the process of lithographically patterned nanoscale electrodeposition (LPNE) with colloidal lithography is described. Nanoring array fabrication was accomplished in three steps: (i) a thin (70 nm) sacrificial nickel or silver film was first vapor-deposited onto a plasma-etched packed colloidal monolayer; (ii) the polymer colloids were removed from the surface, a thin film of positive photoresist was applied, and a backside exposure of the photoresist was used to create a nanohole electrode array; (iii) this array of nanoscale cylindrical electrodes was then used for the electrodeposition of gold, silver, or nickel nanorings. Removal of the photoresist and sacrificial metal film yielded a nanoring array in which all of the nanoring dimensions were set independently: the inter-ring spacing was fixed by the colloidal radius, the radius of the nanorings was controlled by the plasma etching process, and the width of the nanorings was controlled by the electrodeposition process. A combination of scanning electron microscopy (SEM) measurements and Fourier transform near-infrared (FT-NIR) absorption spectroscopy were used to characterize the nanoring arrays. Nanoring arrays with radii from 200 to 400 nm exhibited a single strong NIR plasmonic resonance with an absorption maximum wavelength that varied linearly from 1.25 to 3.33 µm as predicted by a simple standing wave model linear antenna theory. This simple yet versatile nanoring array fabrication method was also used to electrodeposit concentric double gold nanoring arrays that exhibited multiple NIR plasmonic resonances.

On-chip synthesis of protein microarrays from DNA microarrays via coupled in vitro transcription and translation for surface plasmon resonance imaging biosensor applications.

Protein microarrays are fabricated from double-stranded DNA (dsDNA) microarrays by a one-step, multiplexed enzymatic synthesis in an on-chip microfluidic format and then employed for antibody biosensing measurements with surface plasmon resonance imaging (SPRI). A microarray of dsDNA elements (denoted as generator elements) that encode either a His-tagged green fluorescent protein (GFP) or a His-tagged luciferase protein is utilized to create multiple copies of mRNA (mRNA) in a surface RNA polymerase reaction; the mRNA transcripts are then translated into proteins by cell-free protein synthesis in a microfluidic format. The His-tagged proteins diffuse to adjacent Cu(II)-NTA microarray elements (denoted as detector elements) and are specifically adsorbed. The net result is the on-chip, cell-free synthesis of a protein microarray that can be used immediately for SPRI protein biosensing. The dual element format greatly reduces any interference from the nonspecific adsorption of enzyme or proteins. SPRI measurements for the detection of the antibodies anti-GFP and antiluciferase were used to verify the formation of the protein microarray. This convenient on-chip protein microarray fabrication method can be implemented for multiplexed SPRI biosensing measurements in both clinical and research applications.