Axial Phenoxylation of Aluminum Phthalocyanines for Improved Cannabinoid Sensitivity in OTFT Sensors.

Cannabis producers, consumers, and regulators need fast, accurate, point-of-use sensors to detect Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD) from both liquid and vapor source samples, and phthalocyanine-based organic thin-film transistors (OTFTs) provide a cost-effective solution. Chloro aluminum phthalocyanine (Cl-AlPc) has emerged as a promising material due to its unique coordinating interactions with cannabinoids, allowing for superior sensitivity. This work explores the molecular engineering of AlPc to tune and enhance these interactions, where a series of novel phenxoylated R-AlPcs are synthesized and integrated into OTFTs, which are then exposed to THC and CBD solution and vapor samples. While the R-AlPc substituted molecules have a comparable baseline device performance to Cl-AlPc, their new crystal structures and weakened intermolecular interactions increase sensitivity to THC. Grazing-incidence wide-angle X-ray scattering (GIWAXS) and atomic force microscopy (AFM) are used to investigate this film restructuring, where a significant shift in the crystal structure, grain size, and film roughness is detected for the R-AlPc molecules that do not occur with Cl-AlPc. This significant crystal reorganization and film restructuring are the driving force behind the improved sensitivity to cannabinoids relative to Cl-AlPc and demonstrate that analyte-semiconductor interactions can be enhanced through chemical modification to create more responsive OTFT sensors.

Blade Coating Poly(3-hexylthiophene): The Importance of Molecular Weight on Thin-Film Microstructures.

Poly(3-hexylthiophene) is one of the most prevalent and promising conjugated polymers for use in organic electronics. However, the deposition of this material in thin films is highly dependent on the process, such as blade coating versus spin coating and material properties such as molecular weight. Typically, large polymer dispersity makes it difficult to isolate the effect of molecular weight without considering a distribution. In this study, we characterize oligothiophenes of exactly 8, 11, and 14 repeat units, which were deposited into thin films by varying blade coating conditions and postdeposition annealing. From synchrotron-based grazing incidence wide-angle X-ray scattering (GIWAXS), scanning transmission X-ray microscopy (STXM) and near-edge X-ray absorption fine structure spectroscopy (NEXAFS), Raman microscopy, optical microscopy, and X-ray diffraction (XRD), it was suggested that higher molecular weight polymers exhibit a fast-forming crystalline polymorph (form-1) while low molecular weight polymers exhibit a slow forming polymorph (form-2) with large domain boundaries. As molecular weight is gradually increased, the polymorph formed transitions from form-1 and form-2, where 11 repeat unit oligomers display both polymorphs. We also found that processing conditions can increase the formation of the form-2 polymorph. We also report improved organic thin film transistor (OTFT) performance when form-1 is present. Overall, oligothiophene polymorph formation is highly dependent on the molecular weight and processing conditions, providing critical insight into the importance of polymer weight control in the development of thin-film electronics based on conjugated polymers.

Strong Magnetic Field Annealing for Improved Phthalocyanine Organic Thin-Film Transistors.

Thin-film microstructure, morphology, and polymorphism can be controlled and optimized to improve the performance of carbon-based electronics. Thermal or solvent vapor annealing are common post-deposition processing techniques; however, it can be difficult to control or destructive to the active layer or substrates. Here, the use of a static, strong magnetic field (SMF) as a non-destructive process for the improvement of phthalocyanine (Pc) thin-film microstructure, increasing organic thin-film transistor (OTFTs) mobility by twofold, is demonstrated. Grazing incident wide-angle X-ray scattering (GIWAXS), X-ray diffraction (XRD), and atomic force microscopy (AFM) elucidate the effect of SMF on both para- and diamagnetic Pc thin-films when subjected to a magnetic field. A SMF is found to increase the concentration of oxygen-induced radical species within the Pc thin-film, lending a paramagnetic character to ordinarily diamagnetic metal-free Pc and resulting in magnetic field induced changes to its thin-film microstructures. In a nitrogen environment, without competing degradation effects of molecular oxygen, SMF processing is found to favorably improve charge transport characteristics and increase OTFT mobility. Thus, post-deposition thin-film annealing with a magnetic field is presented as an alternative and promising technique for future thin-film engineering applications.

Dopant-Stabilized Assembly of Poly(3-hexylthiophene).

Polymer self-assembly is a powerful approach for forming nanostructures for solution-phase applications. However, polymer semiconductor assembly has primarily been driven by solvent interactions. Here, we report poly(3-hexythiophene) homopolymer assembly driven and stabilized by oxidative doping with iron (III) p-toluenesulfonate in benzonitrile. By this improved method, dopant mol % and addition temperature determine the size and morphology of oxidized polymer nanostructures. The dopant counterion provides colloidal stability in a process of dopant-stabilized assembly (DSA). Each variable governing polymer assembly is systematically varied, revealing general principles of oxidized nanostructure assembly and allowing the polymer planarity, optical absorption, and doping level to be modulated. Oxidized nanostructure heights, lengths, and widths are shown to depend on these properties, which we hypothesize is due to competing nanostructure formation and oxidation mechanisms that are governed by the polymer conformation upon doping. Finally, we demonstrate that the nanoparticle oxidative doping level can be tuned post-formation through sequential dopant addition. By revealing the fundamental processes underlying DSA, this work provides a powerful toolkit to control the assembly and optoelectronic properties of oxidatively doped nanostructures in solution.

Surface engineering of zinc phthalocyanine organic thin-film transistors results in part-per-billion sensitivity towards cannabinoid vapor.

Phthalocyanine-based organic thin-film transistors (OTFTs) have been demonstrated as sensors for a range of analytes, including cannabinoids, in both liquid and gas phases. Detection of the primary cannabinoids, Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD), is necessary for quality control and regulation, however, current techniques are often not readily available for consumers, industry, and law-enforcement. The OTFT characteristics, X-ray diffraction (XRD) spectra, and grazing incident wide angle x-ray scattering (GIWAXS) spectra of two copper and three zinc phthalocyanines, with varying degrees of peripheral fluorination, were screened to determine sensitivity to THC vapor. Unsubstituted ZnPc was found to be the most sensitive material and, by tuning thin-film morphology, crystal polymorphs, and thickness through altered physical vapor deposition conditions, we increased the sensitivity to THC by 100x. Here we demonstrate that deposition conditions, and the resulting physical film characteristics, play a significant role in device sensitization.

Thin-Film Engineering of Solution-Processable n-Type Silicon Phthalocyanines for Organic Thin-Film Transistors.

Metal and metalloid phthalocyanines are an abundant and established class of materials widely used in the dye and pigment industry as well as in commercial photoreceptors. Silicon phthalocyanines (SiPcs) are among the highest-performing n-type semiconductor materials in this family when used in organic thin-film transistors (OTFTs) as their performance and solid-state arrangement are often increased through axial substitution. Herein, we study eight axially substituted SiPcs and their integration into solution-processed n-type OTFTs. Electrical characterization of the OTFTs, combined with atomic force microscopy (AFM), determined that the length of the alkyl chain affects device performance and thin-film morphology. The effects of high-temperature annealing and spin coating time on film formation, two key processing steps for fabrication of OTFTs, were investigated by grazing-incidence wide-angle X-ray scattering (GIWAXS) and X-ray diffraction (XRD) to elucidate the relationship between thin-film microstructure and device performance. Thermal annealing was shown to change both film crystallinity and SiPc molecular orientation relative to the substrate surface. Spin time affected film crystallinity, morphology, and interplanar d-spacing, thus ultimately modifying device performance. Of the eight materials studied, bis(tri-n-butylsilyl oxide) SiPc exhibited the greatest electron field-effect mobility (0.028 cm2 V-1 s-1, a threshold voltage of 17.6 V) of all reported solution-processed SiPc derivatives.

Metal phthalocyanines: thin-film formation, microstructure, and physical properties.

Metal phthalocyanines (MPcs) are an abundant class of small molecules comprising of a highly conjugated cyclic structure with a central chelated metal ion. Due to their remarkable chemical, mechanical, and thermal stability MPcs have become popular for a multitude of applications since their discovery in 1907. The potential for peripheral and axial functionalization affords structural tailoring to create bespoke MPc complexes for various next generation applications. Specifically, thin-films of MPcs have found promising utility in medical and electronic applications where the need to understand the relationship between chemical structure and the resulting thin-film properties is an important ongoing field. This review aims to compile the fundamental principles of small molecule thin-film formation by physical vapour deposition and solution processing focusing on the nucleation and growth of crystallites, thermodynamic and kinetic considerations, and effects of deposition parameters on MPc thin-films. Additionally, the structure-property relationship of MPc thin-films is examined by film microstructure, morphology and physical properties. The topics discussed in this work will elucidate the foundations of MPc thin-films and emphasize the critical need for not only molecular design of new MPcs but the role of their processing in the formation of thin-films and how this ultimately governs the performance of the resulting application.