Improved ACOM pattern matching in 4D-STEM through adaptive sub-pixel peak detection and image reconstruction.

The technique known as 4D-STEM has recently emerged as a powerful tool for the local characterization of crystalline structures in materials, such as cathode materials for Li-ion batteries or perovskite materials for photovoltaics. However, the use of new detectors optimized for electron diffraction patterns and other advanced techniques requires constant adaptation of methodologies to address the challenges associated with crystalline materials. In this study, we present a novel image-processing method to improve pattern matching in the determination of crystalline orientations and phases. Our approach uses sub-pixel adaptive image processing to register and reconstruct electron diffraction signals in large 4D-STEM datasets. By using adaptive prominence and linear filters, we can improve the quality of the diffraction pattern registration. The resulting data compression rate of 103 is well-suited for the era of big data and provides a significant enhancement in the performance of the entire ACOM data processing method. Our approach is evaluated using dedicated metrics, which demonstrate a high improvement in phase recognition. Several features are extracted from the registered data to map properties such as the spot count, and various virtual dark fields, which are used to enhance the handling of the results maps. Our results demonstrate that this data preparation method not only enhances the quality of the resulting image but also boosts the confidence level in the analysis of the outcomes related to determining crystal orientation and phase. Additionally, it mitigates the impact of user bias that may occur during the application of the method through the manipulation of parameters.

Enhanced Performance of KVPO4F0.5O0.5 in Potassium Batteries by Carbon Coating Interfaces.

Potassium vanadium oxyfluoride phosphate of composition KVPO4F0.5O0.5 was modified by a carbon coating to enhance its electrochemical performance. Two distinct methods were used, first, chemical vapor deposition (CVD) using acetylene gas as a carbon precursor and second, an aqueous route using an abundant, cheap, and green precursor (chitosan) followed by a pyrolysis step. The formation of a 5 to 7 nm-thick carbon coating was confirmed by transmission electron microscopy and it was found to be more homogeneous in the case of CVD using acetylene gas. Indeed, an increase of the specific surface area of one order of magnitude, low content of C sp2, and residual oxygen surface functionalities were observed when the coating was obtained using chitosan. Pristine and carbon-coated materials were compared as positive electrode materials in potassium half-cells cycled at a C/5 (C = 26.5 mA g-1) rate within a potential window of 3 to 5 V vs K+/K. The formation by CVD of a uniform carbon coating with the limited presence of surface functions was shown to improve the initial coulombic efficiency up to 87% for KVPFO4F0.5O0.5-C2H2 and to mitigate electrolyte decomposition. Thus, performance at high C-rates such as 10 C was significantly improved, with ∼50% of the initial capacity maintained after 10 cycles, whereas a fast capacity loss is observed for the pristine material.

Improved Electrochemical Performance for High-Voltage Spinel LiNi0.5Mn1.5O4 Modified by Supercritical Fluid Chemical Deposition.

Among candidates at the positive electrode of the next generation of Li-ion technology and even beyond post Li-ion technology as all-solid-state batteries, spinel LiNi0.5Mn1.5O4 (LNMO) is one of the favorites. Nevertheless, before its integration into commercial systems, challenges still remain to be tackled, especially the stabilization of interfaces with the electrolyte (liquid or solid) at high voltage. In this work, a simple, fast, and cheap process is used to prepare a homogeneous coating of Al2O3 type to modify the surface of the spinel LNMO: the supercritical fluid chemical deposition (SFCD) route. This process is, to the best of our knowledge, used for the first time in the battery field. Significantly improved performance was demonstrated vs those of bare LNMO, especially at high rates and for highly loaded electrodes.

Particle nanosizing and coating with an ionic liquid: two routes to improve the transport properties of Na3V2(PO4)2FO2.

Na3V2(PO4)2FO2 is a promising candidate for practical use as a positive electrode material in Na-ion batteries thanks to its high voltage and excellent structural stability upon cycling. However, its limited intrinsic transport properties limit its performance at fast charge/discharge rates. In this work, two efficient approaches are presented to optimize the electrical conductivity of the electrode material: particle nanosizing and particle coating with an ionic liquid (IL). The former reveals that particle downsizing from micrometer to nanometer range improves the electronic conductivity by more than two orders of magnitude, which greatly improves the rate capability without affecting the capacity retention. The second approch dealing with an original surface modification by applying an IL coating strongly enhances the ionic mobility and offers new perspectives to improve the energy storage performance by designing the electrode materials' surface composition.

Reactivity at the Electrode-Electrolyte Interfaces in Li-Ion and Gel Electrolyte Lithium Batteries for LiNi0.6Mn0.2Co0.2O2 with Different Particle Sizes.

The layered oxide LiNi0.6Mn0.2Co0.2O2 is a very attractive positive electrode material, as shown by the good reversible capacity, chemical stability, and cyclability upon long-range cycling in Li-ion batteries and, hopefully, in the near future, in all-solid-state batteries. Three samples with variable primary particle sizes of 240 nm, 810 nm, and 2.1 µm on average and very similar structures close to the ideal 2D layered structure (less than 2% Ni2+ ions in Li+ sites) were obtained by coprecipitation followed by a solid-state reaction at high temperatures. The electrochemical performances of the materials were evaluated in a conventional organic liquid electrolyte in Li-ion batteries and in a gel electrolyte in all-solid-state batteries. The positive electrode/electrolyte interface was analyzed by X-ray photoelectron spectroscopy to determine its composition and the extent of degradation of the lithium salt and the carbonate solvents after cycling, taking into account the changes in particle size of the positive electrode material and the nature of the electrolyte.

Impact of Synthesis Conditions in Na-Rich Prussian Blue Analogues.

Sodium-rich iron hexacyanoferrates were prepared by coprecipitation, hydrothermal route, and under reflux, with or without dehydration. They were obtained with different structures described in cubic, orthorhombic, or rhombohedral symmetry, with variable compositions in sodium, water, and cationic vacancies and with a variety of morphologies. This series of sodium-rich Prussian blue analogues allowed addressing the relationship between synthesis conditions, composition, structure, morphology, and electrochemical properties in Na-ion batteries. A new orthorhombic phase with the Na1.8Fe2(CN)6·0.7H2O composition synthesized by an hydrothermal route at 140 °C is reported for the first time, whereas a phase of Na2Fe2(CN)6·2H2O composition obtained under reflux, previously described with a monoclinic structure, shows in fact a rhombohedral structure.

Towards Reversible High-Voltage Multi-Electron Reactions in Alkali-Ion Batteries Using Vanadium Phosphate Positive Electrode Materials.

Vanadium phosphate positive electrode materials attract great interest in the field of Alkali-ion (Li, Na and K-ion) batteries due to their ability to store several electrons per transition metal. These multi-electron reactions (from V2+ to V5+) combined with the high voltage of corresponding redox couples (e.g., 4.0 V vs. for V3+/V4+ in Na3V2(PO4)2F3) could allow the achievement the 1 kWh/kg milestone at the positive electrode level in Alkali-ion batteries. However, a massive divergence in the voltage reported for the V3+/V4+ and V4+/V5+ redox couples as a function of crystal structure is noticed. Moreover, vanadium phosphates that operate at high V3+/V4+ voltages are usually unable to reversibly exchange several electrons in a narrow enough voltage range. Here, through the review of redox mechanisms and structural evolutions upon electrochemical operation of selected widely studied materials, we identify the crystallographic origin of this trend: the distribution of PO4 groups around vanadium octahedra, that allows or prevents the formation of the vanadyl distortion (O…V4+=O or O…V5+=O). While the vanadyl entity massively lowers the voltage of the V3+/V4+ and V4+/V5+ couples, it considerably improves the reversibility of these redox reactions. Therefore, anionic substitutions, mainly O2- by F-, have been identified as a strategy allowing for combining the beneficial effect of the vanadyl distortion on the reversibility with the high voltage of vanadium redox couples in fluorine rich environments.

Ionothermal Synthesis of Polyanionic Electrode Material Na3V2(PO4)2FO2 through a Topotactic Reaction.

Polyanionic Na3V2(PO4)2FO2 has been successfully prepared for the first time by ionothermal reaction in 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM TFSI) ionic liquid. Its structure and elemental stoichiometry are confirmed by X-ray diffraction, NMR spectroscopy, and ICP-OES, respectively. Furthermore, the scanning electron microscopy reveals that the as-obtained material possesses an original platelet-like morphology. A topochemical reaction mechanism is proposed to explain the formation of the 3D framework of Na3V2(PO4)2FO2 from layered compound α-VOPO4·2H2O. Galvanostatic electrochemical tests indicate a modification of the desodiation and sodiation mechanism of the as-prepared Na3V2(PO4)2FO2 compared to those synthesized by conventional solid-state approaches. Furthermore, the electrochemical performance of Na3V2(PO4)2FO2 obtained at different cycling rates is also discussed.

Local atomic and electronic structure in the LiVPO4 (F,O) tavorite-type materials from solid-state NMR combined with DFT calculations.

7 Li, 31 P, and 19 F solid-state nuclear magnetic resonance (NMR) spectroscopy was used to investigate the local arrangement of oxygen and fluorine in LiVPO4 F1-y Oy materials, interesting as positive electrode materials for Li-ion batteries. From the evolution of the 1D spectra versus y, 2D 7 Li radiofrequency-driven recoupling (RFDR) experiments combined, and a tentative signal assignment based on density functional theory (DFT) calculations, it appears that F and O are not randomly dispersed on the bridging X position between two X-VO4 -X octahedra (X = O or F) but tend to segregate at a local scale. Using DFT calculations, we analyzed the impact of the different local environments on the local electronic structure. Depending on the nature of the VO4 X2 environments, vanadium ions are either in the +III or in the +IV oxidation state and can exhibit different distributions of their unpaired electron(s) on the d orbitals. Based on those different local electronic structures and on the computed Fermi contact shifts, we discuss the impact on the spin transfer mechanism on adjacent nuclei and propose tentative signal assignments. The O/F clustering tendency is discussed in relation with the formation of short VIV O vanadyl bonds with a very specific electronic structure and possible cooperative effect along the chain.

Monitoring the Crystal Structure and the Electrochemical Properties of Na3(VO)2(PO4)2F through Fe3+ Substitution.

We here present the synthesis of a new material, Na3(VO)Fe(PO4)2F2, by the sol-gel method. Its atomic and electronic structural descriptions are determined by a combination of several diffraction and spectroscopy techniques such as synchrotron X-ray powder diffraction and synchrotron X-ray absorption spectroscopy at V and Fe K edges, 57Fe Mössbauer, and 31P solid-state nuclear magnetic resonance spectroscopy. The crystal structure of this newly obtained phase is similar to that of Na3(VO)2(PO4)2F, with a random distribution of Fe3+ ions over vanadium sites. Even though Fe3+ and V4+ ions situate on the same crystallographic position, their local environment can be studied separately using 57Fe Mössbauer and X-ray absorption spectroscopy at Fe and V K edges, respectively. The Fe3+ ion resides in a symmetric octahedral environment, while the octahedral site of V4+ is greatly distorted due to the presence of the vanadyl bond. No electrochemical activity of the Fe4+/Fe3+ redox couple is detected, at least up to 5 V, whereas the reduction of Fe3+ to Fe2+ has been observed at ∼1.5 V versus Na+/Na through the insertion of 0.5 Na+ into Na3(VO)Fe(PO4)2F2. Comparing to Na3(VO)2(PO4)2F, the electrochemical profile of Na3(VO)Fe(PO4)2F2 in the same cycling condition shows a smaller polarization which could be due to a slight improvement in Na+ diffusion process thanks to the presence of Fe3+ in the framework. Furthermore, the desodiation mechanism occurring upon charging is investigated by operando synchrotron X-ray diffraction and operando synchrotron X-ray absorption at V K edge.

Aluminum substitution for vanadium in the Na3V2(PO4)2F3 and Na3V2(PO4)2FO2 type materials.

Among the positive electrode materials for Na-ion batteries, Na3V2(PO4)2F3 is considered as one of the most promising and generates high interest. Here, we study the influence of the sol-gel synthesis parameters on the structure and on the electrochemical signature of the partially substituted Na3V2-zAlz(PO4)2(F,O)3 materials. We demonstrate that the acidity of the starting solution influences the vanadium oxidation state of the final product. For the first time we report on the possibility of controlling the double Al/V and O/F substitution that leads to the preparation of the Na3V2-zAlz(PO4)2F1+zO2-z solid solution.

Surface Reactivity of Li2MnO3: First-Principles and Experimental Study.

This article deals with the surface reactivity of (001)-oriented Li2MnO3 crystals investigated from a multitechnique approach combining material synthesis, X-ray photoemission spectroscopy (XPS), scanning electron microscopy, Auger electron spectroscopy, and first-principles calculations. Li2MnO3 is considered as a model compound suitable to go further in the understanding of the role of tetravalent manganese atoms in the surface reactivity of layered lithium oxides. The knowledge of the surface properties of such materials is essential to understand the mechanisms involved in parasitic phenomena responsible for early aging or poor storage performances of lithium-ion batteries. The surface reactivity was probed through the adsorption of SO2 gas molecules on large Li2MnO3 crystals to be able to focus the XPS beam on the top of the (001) surface. A chemical mapping and XPS characterization of the material before and after SO2 adsorption show in particular that the adsorption is homogeneous at the micro- and nanoscale and involves Mn reduction, whereas first-principles calculations on a slab model of the surface allow us to conclude that the most energetically favorable species formed is a sulfate with charge transfer implying reduction of Mn.

Morphology and Surface Reactivity Relationship in the Li1+xMn2-xO4 Spinel with x = 0.05 and 0.10: A Combined First-Principle and Experimental Study.

This article focuses on the surface reactivity of two spinel samples with different stoichiometries and crystal morphologies, namely Li1+xMn2-xO4 with x = 0.05 and 0.10. LiMn2O4 compounds are good candidates as positive electrode of high-power lithium-ion batteries for portable devices. The samples were investigated using both experimental and theoretical approaches. On the experimental point of view, they were characterized in depth from X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS) analyses. Then, the reactivity was investigated through the adsorption of (SO2) gaseous probes, in controlled conditions, followed by XPS characterization. First-principle calculations were conducted simultaneously to investigate the electronic properties and the reactivity of relevant surfaces of an ideal LiMn2O4 material. The results allow us to conclude that the reactivity of the samples is dominated by an acido-basic reactivity and the formation of sulfite species. Nonetheless, on the x = 0.05 sample, both sulfite and sulfate species are obtained, the later, in lesser extent, corresponding to a redox reactivity. Combining experimental and theoretical results, this redox reactivity could be associated with the presence of a larger quantity of Mn4+ cations on the last surface layers of the material linked to a specific surface orientation.

Crystal Structure and Lithium Diffusion Pathways of a Potential Positive Electrode Material for Lithium-Ion Batteries: Li2VIII(H0.5PO4)2.

A new potentially interesting material as a positive electrode for lithium-ion batteries, Li2VIII(H0.5PO4)2, was obtained by hydrothermal synthesis. Its crystal structure was solved thanks to single-crystal X-ray diffraction. This material is isostructural to Li2FeIII(PO4)(HPO4) and also closely related to Li2FeII(SO4)2. It can be described as a VO6 octahedron sharing corners with six PO4 tetrahedra to form a 3D framework. One oxygen atom of each phosphate group is unshared with a vanadium octahedron and as such linked to a hydrogen atom. The arrangement of these polyhedra generates large channels running along [100] in which lithium cations are located. The close structural relationship between Li2FeIII(PO4)(HPO4) and Li2FeII(SO4)2 allows one to investigate, by comparison, the effect of the hydrogen atoms lying on lithium diffusion pathways.

Spinel materials for Li-ion batteries: new insights obtained by operando neutron and synchrotron X-ray diffraction.

In the last few decades Li-ion batteries changed the way we store energy, becoming a key element of our everyday life. Their continuous improvement is tightly bound to the understanding of lithium (de)intercalation phenomena in electrode materials. Here we address the use of operando diffraction techniques to understand these mechanisms. We focus on powerful probes such as neutrons and synchrotron X-ray radiation, which have become increasingly familiar to the electrochemical community. After discussing the general benefits (and drawbacks) of these characterization techniques and the work of customization required to adapt standard electrochemical cells to an operando diffraction experiment, we highlight several very recent results. We concentrate on important electrode materials such as the spinels Li1 + xMn2 - xO4 (0 ≤ x ≤ 0.10) and LiNi0.4Mn1.6O4. Thorough investigations led by operando neutron powder diffraction demonstrated that neutrons are highly sensitive to structural parameters that cannot be captured by other means (for example, atomic Debye-Waller factors and lithium site occupancy). Synchrotron radiation X-ray powder diffraction reveals how LiMn2O4 is subject to irreversibility upon the first electrochemical cycle, resulting in severe Bragg peak broadening. Even more interestingly, we show for the first time an ordering scheme of the elusive composition Li0.5Mn2O4, through the coexistence of Mn(3+):Mn(4+) 1:3 cation ordering and lithium/vacancy ordering. More accurately written as Li0.5Mn(3+)0.5Mn(4+)1.5O4, this intermediate phase loses the Fd\overline 3m symmetry, to be correctly described in the P213 space group.

Recent achievements on inorganic electrode materials for lithium-ion batteries.

The lithium-ion battery technology is rooted in the studies of intercalation of guest ions into inorganic host materials developed ca. 40 years ago. It further turned into a commercial product, which will soon blow its 25th candle. Intense research efforts during this time have resulted in the development of a large spectrum of electrode materials together with deep understanding of the underlying structure-property relationships that govern their performance. This has enabled an ever increasing electrochemical yield together with the diversification of the technology into several subfamilies, tailoring materials to application requirements. The present paper aims at providing a global and critical perspective on inorganic electrode materials for lithium-ion batteries categorized by their reaction mechanism and structural dimensionality. Specific emphasis is put on recent research in the field, which beyond the chemistry and microstructure of the materials themselves also involves considering interfacial chemistry concepts alongside progress in characterization techniques. Finally a short personal perspective is provided on some plausible development of the field.

Iron(III) phosphates obtained by thermal treatment of the Tavorite-type FePO4·H2O material: structures and electrochemical properties in lithium batteries.

Thermal treatment of the Tavorite-type material FePO(4)·H(2)O leads to the formation of two crystallized iron phosphates, very similar in structure. Their structural description is proposed taking into account results obtained from complementary characterization tools (thermal analyses, diffraction, and spectroscopy). These structures are similar to that of the pristine material FePO(4)·H(2)O: iron atoms are distributed between the chains of corner-sharing FeO(6) octahedra observed in FePO(4)·H(2)O and the octahedra from the tunnels previously empty, in good agreement with the formation of a Fe(4/3)PO(4)(OH)-type phase. The formation of an extra disordered phase was also proposed. These samples obtained by thermal-treatment of FePO(4)·H(2)O also intercalate lithium ions through the reduction of Fe(3+) to Fe(2+) at an average voltage of ~2.6 V (vs Li(+)/Li), with a good cyclability and a reversible capacity around 120 mA h g(-1) (>160 mA h g(-1) during the first discharge).

Thermal stability of Li2MnO3: from localized defects to the spinel phase.

The thermal stability of Li(2)MnO(3) has been investigated by the means of coupled differential thermal analysis and thermogravimetric analysis associated with powder X ray diffraction. Various experiments performed in air and in argon allowed us to propose a mechanism of spinel-type defects formation in intergrowth with Li(2)MnO(3) when treated in air above 900 °C. The fidelity of the DIFFaX simulations performed led to the understanding of the influence of the existence of spinel type defects intergrowth on X ray and electron diffraction patterns. The formation of these defects occurs during cooling and is preceded by the formation of LiMnO(2) defects in heating. With sufficiently long thermal treatments, defects expand such that a spinel type phase can be observed after cooling.

Structural study of the Li(0.5)Na(0.5)MnFe2(PO4)3 and Li(0.75)Na(0.25)MnFe2(PO4)3 alluaudite phases and their electrochemical properties as positive electrodes in lithium batteries.

The alluaudite lithiated phases Li(0.5)Na(0.5)MnFe(2)(PO(4))(3) and Li(0.75)Na(0.25)MnFe(2)(PO(4))(3) were prepared via a sol-gel synthesis, leading to powders with spongy characteristics. The Rietveld refinement of the X-ray and neutron diffraction data coupled with ab initio calculations allowed us for the first time to accurately localize the lithium ions in the alluaudite structure. Actually, the lithium ions are localized in the A(1) and A(1)' sites of the tunnel. Mössbauer measurements showed the presence of some Fe(2+) that decreased with increasing Li content. Neutron diffraction revealed the presence of a partial Mn/Fe exchange between the two transition metal sites that shows clearly that the oxidation state of the element is fixed by the type of occupied site. The electrochemical properties of the two phases were studied as positive electrodes in lithium batteries in the 4.5-1.5 V potential window, but they exhibit smaller electrochemical reversible capacity compared with the non-lithiated NaMnFe(2)(PO(4))(3). The possibility of Na(+)/Li(+) ion deintercalation from (Na,Li)MnFe(2)(PO(4))(3) was also investigated by DFT+U calculations.