Towards advanced removal of organics in persulfate solution by heterogeneous iron-based catalyst: A review.

Heterogeneous iron-based catalysts have drawn increasing attention in the advanced oxidation of persulfates due to their abundance in nature, the lack of secondary pollution to the environment, and their low cost over the last a few years. In this paper, the latest progress in the research on the activation of persulfate by heterogeneous iron-based catalysts is reviewed from two aspects, in terms of synthesized catalysts (Fe0, Fe2O3, Fe3O4, FeOOH) and natural iron ore catalysts (pyrite, magnetite, hematite, siderite, goethite, ferrohydrite, ilmenite and lepidocrocite) focusing on efforts made to improve the performance of catalysts. The advantages and disadvantages of the synthesized catalysts and natural iron ore were summarized. Particular interests were paid to the activation mechanisms in the catalyst/PS/pollutant system for removal of organic pollutants. Future research challenges in the context of field application were also discussed.

Synthesis and evaluation of a novel cross-linked biochar/ferric chloride hybrid material for integrated coagulation and adsorption of turbidity and humic acid from synthetic wastewater: Implications for sludge valorisation.

The deep removal of organic pollutants is challenging for coagulation technology in drinking water and wastewater treatment plants to satisfy the rising water standards. Iron (III) chloride (FeCl3) is a popular inorganic coagulant; although it has good performance in removing the turbidity (TB) in water at an alkaline medium, it cannot remove dissolved pollutants and natural organic matter such as humic acid water solution. Additionally, its hygroscopic nature complicates determining the optimal dosage for effective coagulation. Biochar (BC), a popular adsorbent with abundant functional groups, porous structure, and relatively high surface area, can adsorb adsorbates from water matrices. Therefore, combining BC with FeCl3 presents a potential solution to address the challenges associated with iron chloride. Consequently, this study focused on preparing and characterizing a novel biochar/ferric chloride-based coagulant (BC-FeCl3) for efficient removal of turbidity (TB) and natural organic matter, specifically humic acid (HA), from synthetic wastewater. The potential solution for the disposal of produced sludge was achieved by its recovering and recycling, then used in adsorption of HA from aqueous solution. The novel coagulant presented high TB and HA removal within 10 min of settling period at pH solution of 7.5. Furthermore, the recovered sludge presented a good performance in the adsorption of HA from aqueous solution. Adsorption isotherm and kinetics studies revealed that the Pseudo-second-order model best described kinetic adsorption, while the Freundlich model dominated the adsorption isotherm.

Chemical methods to remove microplastics from wastewater: A review.

Microplastics (Mps) have emerged as a pervasive environmental concern, with their presence detected not only in freshwater ecosystems but also in drinking and bottled water sources. While extensive research has centered on understanding the origins, migration patterns, detection techniques, and ecotoxicological impacts of these contaminants, there remains a notable research gap about the strategies for Mps removal. This study reviews existing literature on chemical approaches for mitigating microplastic contamination within wastewater systems, focusing on coagulation precipitation, electrocoagulation, and advanced oxidation methods. Each approach is systematically explored, encompassing their respective mechanisms and operational dynamics. Furthermore, the comparative analysis of these three techniques elucidates their strengths and limitations in the context of MPs removal. By shedding light on the intricate mechanisms underlying these removal methods, this review contributes to the theoretical foundation of microplastic elimination from wastewater and identifies future research trajectories and potential challenges.

Uptake, accumulation, and degradation of dibutyl phthalate by three wetland plants.

The uptake and degradation mechanisms of dibutyl phthalate (DBP) by three wetland plants, namely Lythrum salicaria, Thalia dealbata, and Canna indica, were studied using hydroponics. The results revealed that exposure to DBP at 0.5 mg/L had no significant effect on the growth of L. salicaria and C. indica but inhibited the growth of T. dealbata. After 28 days, DBP concentrations in the roots of L. salicaria, T. dealbata, and C. indica were 8.74, 5.67, and 5.46 mg/kg, respectively, compared to 2.03-3.95 mg/kg in stems and leaves. Mono-n-butyl phthalate concentrations in L. salicaria tissues were significantly higher than those in the other two plants at 23.1, 15.0, and 13.6 mg/kg in roots, stems, and leaves, respectively. The roots of L. salicaria also had the highest concentration of phthalic acid, reaching 2.45 mg/kg. Carboxylesterase, polyphenol oxidase, and superoxide dismutase may be the primary enzymes involved in DBP degradation in wetland plants. The activities of these three enzymes exhibited significant changes in plant tissues. The findings suggest L. salicaria as a potent plant for phytoremediation and use in constructed wetlands for the treatment of DBP-contaminated wastewater.

Facile Synthesis of Magnetic Biochar Derived from Burley Tobacco Stems towards Enhanced Cr(VI) Removal: Performance and Mechanism.

In this study, ferric-loaded magnetic burley tobacco stem biochar (MBTS) was synthesized via pyrolysis to improve the removal of Cr(VI). The results showed that MBTS had an adsorption capacity of 54.92 mg Cr(VI)/g, which was about 14 times higher than raw burley tobacco stem biochar (i.e., 3.84 mg/g). According to the findings obtained, a three-step mechanism of Cr(VI) removal by MBTS was further put forward, i.e., (1) Cr(VI) exchanged with hydroxyl groups on MBTS, (2) the reduction in Cr(VI) to Cr(III) mediated by oxygen-containing groups, and (3) the chelation of produced Cr(III) with the amino groups on MBTS. FTIR spectra further revealed that C-N, C-H, and C=C groups played an important role in Cr(VI) removal. Furthermore, the adsorption equilibrium and kinetics of Cr(VI) on MBTS could better be described by the Langmuir equation and pseudo-second-order rate equation. This study clearly demonstrated that ferric-loaded biochar derived from burley tobacco stems could serve as a cost-effective magnetic adsorbent for the high-efficiency removal of soluble Cr(VI) from wastewater. Tobacco stem-adsorbed Cr(VI) realized a green path for treating waste by waste.

Investigations on the pyrolysis of microalgal-bacterial granular sludge: Products, kinetics, and potential mechanisms.

This study investigated the pyrolysis of microalgal-bacterial granular sludge for producing bio-oil and biochar. Results showed that the bio-oil productivity of pyrolyzed MBGS reached 39.5-45.4 wt%, while 23.8-41.2% for the nitrogen-containing bio-oil at the temperature of 673-1073 K. Meanwhile the biochar with a nitrogen content of 3.7-7.0 wt% could also be produced. Moreover, the Van-Krevelen diagram revealed that produced bio-oil had a H/C ratio higher than that from agroforestry biomass, but its O/C ratio was found to be similar to those of coal and biochar. It further appeared from a mass conservation analysis that the highest bio-oil production yield was achieved at a pyrolysis temperature of 773 K, while the pyrolytic kinetics of MBGS in the temperature range studied was governed by the 3-D diffusion mechanism with the activation energy of 224.96 kJ·mol-1.

Biomass enhances the reduction of oxidized pellets with carbon monoxide.

In this study, the reduction mechanism of using CO to reduce biomass-oxidized pellets (BOP) and general-oxidized pellets (GOP) was deeply analyzed. The effect of biomass addition on the reduction of oxidized pellets and the change of reduction kinetics were studied. The addition of 2 wt% biomass into pellets increases pores of the oxidized pellets, promotes the rate of CO entering the pellets and the overflow of CO2, which results in faster reduction of the oxidized pellets. The reduction reactions of BOP and GOP were controlled by internal diffusion, mixing control and interface control sequentially. Also, addition of the biomass to the pellets decreases the activation energy required for their reduction, from 87.30 to 80.65 kJ·mol-1. The addition of biomass shortens the reduction time by 3% which can reduce the energy consumption. Therefore, the biomass together with CO enhances the reduction of oxidized pellets and has real environmental benefits.

Microalgal-bacterial granular sludge process outperformed aerobic granular sludge process in municipal wastewater treatment with less carbon dioxide emissions.

The aerobic granular sludge (AGS) process and microalgal-bacterial granular sludge (MBGS) process were comparably applied for municipal wastewater treatment in sequencing batch reactors with a height to diameter ratio of eight. For morphological appearances, the yellow aerobic granules were strip-shaped (4.0 mm × 0.62 mm) while the green microalgal-bacterial granules were elliptical-shaped (2.0 mm × 0.75 mm). The dominated rod-shaped bacteria (e.g., Acidobacteria and Bacteroidetes) and the slender configuration might be associated with the strip shape of aerobic granules under weak acid conditions. The nutrients removal performances by MBGS process were generally slightly better than AGS process. In addition, nutrients removal mechanisms were identified to elucidate how organics, ammonia, and phosphorus were removed by AGS process and MBGS process, respectively. Mass balance calculation estimated that MBGS process appeared to achieve much less CO2 emission (5.8%) compared with AGS process (44.4%). Overall, it proved that MBGS process, with the merits of potentially low energy cost, limited CO2 emission, and excellent performance, showed more prospects in municipal wastewater treatment than AGS process.

Effect of NaCl Concentration on Microbiological Properties in NaCl Assistant Anaerobic Fermentation: Hydrolase Activity and Microbial Community Distribution.

Previous studies have demonstrated that sludge hydrolysis and short-chain fatty acids (SCFAs) production were improved through NaCl assistant anaerobic fermentation. However, the effect of NaCl concentrations on hydrolase activity and microbial community structure was rarely reported. In this study, it was found that α-glucosidase activity and some carbohydrate-degrading bacteria were inhibited in NaCl tests, owing to their vulnerability to high NaCl concentration. Correspondingly, the microbial community richness and diversity were reduced compared with the control test, while the evenness was not affected by NaCl concentration. By contrast, the protease activity was increased in the presence of NaCl and reached the highest activity at the NaCl concentration of 20 g/L. The protein-degrading and SCFAs-producing bacteria (e.g., Clostridium algidicarnis and Proteiniclasticum) were enriched in the presence of NaCl, which were salt-tolerant.

Catalytic pyrolysis of rain tree biomass with nano nickel oxide synthetized from nickel plating slag: A green path for treating waste by waste.

Catalytic pyrolysis of rain tree biomass (RTB), a typical horticultural waste, was investigated with nano-NiO as catalyst produced from hazardous nickel plating slag (NPS). It appeared from the analyses by FTIR, TGA, XRD, BET, and FESEM/EDX that nano-NiO produced had a SBET and mean particle size of 53.4 m2/g and 112.3 nm. The catalytic pyrolysis kinetics of RTB with and without catalyst were studied by Friedman method. It was found that the activation energy (Ea) was in the range of 177 to 360 kJ/mol at a conversion rate of 0.1 - 0.75. The results further revealed that the H2 increase ratio in pyrolysis above 500 °C was more than 40% in the presence of catalyst. Consequently, this study showed the great potential of nano-NiO as a high-efficiency catalyst in recovering energy from biomass.

Insight into the Ex Situ Catalytic Pyrolysis of Biomass over Char Supported Metals Catalyst: Syngas Production and Tar Decomposition.

Ex situ catalytic pyrolysis of biomass using char-supported nanoparticles metals (Fe and Ni) catalyst for syngas production and tar decomposition was investigated. The characterizations of fresh Fe-Ni/char catalysts were determined by TGA, SEM-EDS, Brunauer-Emmett-Teller (BET), and XPS. The results indicated that nanoparticles metal substances (Fe and Ni) successfully impregnated into the char support and increased the thermal stability of Fe-Ni/char. Fe-Ni/char catalyst exhibited relatively superior catalytic performance, where the syngas yield and the molar ratio of H2/CO were 0.91 Nm3/kg biomass and 1.64, respectively. Moreover, the lowest tar yield (43.21 g/kg biomass) and the highest tar catalytic conversion efficiency (84.97 wt.%) were also obtained under the condition of Ni/char. Ultimate analysis and GC-MS were employed to analyze the characterization of tar, and the results indicated that the percentage of aromatic hydrocarbons appreciably increased with the significantly decrease in oxygenated compounds and nitrogenous compounds, especially in Fe-Ni/char catalyst, when compared with no catalyst pyrolysis. After catalytic pyrolysis, XPS was employed to investigate the surface valence states of the characteristic elements in the catalysts. The results indicated that the metallic oxides (MexOy) were reduced to metallic Me0 as active sites for tar catalytic pyrolysis. The main reactions pathway involved during ex situ catalytic pyrolysis of biomass based on char-supported catalyst was proposed. These findings indicate that char has the potential to be used as an efficient and low-cost catalyst toward biomass pyrolysis for syngas production and tar decomposition.

An innovative alkaline protease-based pretreatment approach for enhanced short-chain fatty acids production via a short-term anaerobic fermentation of waste activated sludge.

This study reported a novel pretreatment approach with combination of alkaline protease (AP) and pH 10 for enhancing short-chain fatty acids (SCFAs) production from waste activated sludge (WAS). Through the AP-based pretreatment, WAS flocs were disintegrated with cell lysis, leading to release of biodegradable organic matters. At the external AP dosage of 5%, SCOD of 5363.7 mg/L (SCOD/TCOD = 32.5%) was achievable after 2-h pretreatment. More than 66% of SCOD was composed of proteins and carbohydrates. Considerable SCFAs of 607 mg COD/g VSS was produced over a short-term anaerobic fermentation of 3 days, which was 5.4 times higher than that in the control. Acetic and propionic acids accounted for 74.1% of the SCFAs. The AP-based approach increased endogenous protease and α-glucosidase activities, facilitating biodegradation of dissolved organic matters and SCFAs production. Such approach is promising for WAS disposal and carbon recovery, the produced SCFAs might supply 60% of carbon gap in wastewater.

Almond Shell-Derived, Biochar-Supported, Nano-Zero-Valent Iron Composite for Aqueous Hexavalent Chromium Removal: Performance and Mechanisms.

Nano-zero-valent iron biochar derived from almond shell (nZVI-ASBC) was used for hexavalent chromium (CR) removal. Experiments showed that pH was the main factor (p < 0.01) that affected the experimental results. At a dosage of 10 mg·L-1 and pH of 2-6, in the first 60 min, nZVI-ASBC exhibited a removal efficiency of 99.8%, which was approximately 20% higher than the removal yield at pH 7-11. Fourier transform infrared spectroscopy results indicated N-H was the main functional group that influenced the chemisorption process. The pseudo second-order dynamics and Langmuir isotherm models proved to be the most suitable. Thermodynamic studies showed that the reaction was exothermic and spontaneous at low temperatures (T < 317 K). Various interaction mechanisms, including adsorption and reduction, were adopted for the removal of Cr(VI) using the nZVI-ASBC composite. The findings showed that the BC-modified nZVI prepared with almond shell exerts a good effect and could be used for the removal of Cr(VI).

RNA sequencing and anthocyanin synthesis-related genes expression analyses in white-fruited Vaccinium uliginosum.

BACKGROUND: Vaccinium uliginosum (Ericaceae) is an important wild berry having high economic value. The white-fruited V. uliginosum variety found in the wild lacks anthocyanin and bears silvery white fruits. Hence, it is a good resource for investigating the mechanism of fruit color development. This study aimed to verify the differences in the expression levels of some structural genes and transcription factors affecting the anthocyanin biosynthesis pathway by conducting high-throughput transcriptome sequencing and real-time PCR analysis by using the ripening fruits of V. uliginosum and the white-fruited variety. RESULTS: We annotated 42,837 unigenes. Of the 325 differentially expressed genes, 41 were up-regulated and 284 were down-regulated. Further, 11 structural genes of the flavonoid pathway were up-regulated, whereas two were down-regulated. Of the seven genes encoding transcription factors, five were up-regulated and two were down-regulated. The structural genes VuCHS, VuF3'H, VuFHT, VuDFR, VuANS, VuANR, and VuUFGT and the transcription factors VubHLH92, VuMYB6, VuMYBPA1, VuMYB11, and VuMYB12 were significantly down-regulated. However, the expression of only VuMYB6 and VuMYBPA1 rapidly increased during the last two stages of V. uliginosum when the fruit was ripening, consistent with anthocyanin accumulation. CONCLUSIONS: VuMYB6 was annotated as MYB1 by the BLAST tool. Thus, the white fruit color in the V. uliginosum variant can be attributed to the down-regulation of transcription factors VuMYB1 and VuMYBPA1, which leads to the down-regulation of structural genes associated with the anthocyanin synthesis pathway.

The effect of bioleaching on sewage sludge pyrolysis.

The effects of bioleaching on sewage sludge pyrolysis were studied. Sewage sludge was treated by bioleaching with solid concentrations of 6% (w/v), 8% (w/v), 10% (w/v). Results showed that bioleaching treatment could modify the physicochemical properties of sewage sludge and enhance the metals removal. The optimum removal efficiencies of heavy metals were achieved with solid concentration of 6% (w/v) bioleaching treatment: Cu, 73.08%; Zn, 78.67%; Pb, 24.65%; Cd, 79.46%. The characterization results of thermogravimetric analysis (TGA) showed that the bioleached sewage sludge with a 6% (w/v) solid concentration treatment was the easiest to decompose. Pyrolytic experiments of bioleached sewage sludge were performed in a laboratory-scale fixed bed reactor. Results indicated that bioleaching treatment greatly influenced the product yields and gas composition.