Design, synthesis and biological activities of echinopsine derivatives containing acylhydrazone moiety.

Based on the broad-spectrum biological activities of echinopsine and acylhydrazones, a series of echinopsine derivatives containing acylhydrazone moieties have been designed, synthesized and their biological activities were evaluated for the first time. The bioassay results indicated that most of the compounds showed moderate to good antiviral activities against tobacco mosaic virus (TMV), among which echinopsine (I) (inactivation activity, 49.5 ± 4.4%; curative activity, 46.1 ± 1.5%; protection activity, 42.6 ± 2.3%) and its derivatives 1 (inactivation activity, 44.9 ± 4.6%; curative activity, 39.8 ± 2.6%; protection activity, 47.3 ± 4.3%), 3 (inactivation activity, 47.9 ± 0.9%; curative activity, 43.7 ± 3.1%; protection activity, 44.6 ± 3.3%), 7 (inactivation activity, 46.2 ± 1.6%; curative activity, 45.0 ± 3.7%; protection activity, 41.7 ± 0.9%) showed higher anti-TMV activity in vivo at 500 mg/L than commercial ribavirin (inactivation activity, 38.9 ± 1.4%; curative activity, 39.2 ± 1.8%; protection activity, 36.4 ± 3.4%). Some compounds exhibited insecticidal activities against Plutella xylostella, Mythimna separate and Spodoptera frugiperda. Especially, compounds 7 and 27 displayed excellent insecticidal activities against Plutella xylostell (mortality 67 ± 6% and 53 ± 6%) even at 0.1 mg/L. Additionally, most echinopsine derivatives exhibited high fungicidal activities against Physalospora piricola and Sclerotinia sclerotiorum.

Automatic Assessment of Mitral Regurgitation Severity Using the Mask R-CNN Algorithm with Color Doppler Echocardiography Images.

Accurate assessment of mitral regurgitation (MR) severity is critical in clinical diagnosis and treatment. No single echocardiographic method has been recommended for MR quantification thus far. We sought to define the feasibility and accuracy of the mask regions with a convolutional neural network (Mask R-CNN) algorithm in the automatic qualitative evaluation of MR using color Doppler echocardiography images. The authors collected 1132 cases of MR from hospital A and 295 cases of MR from hospital B and divided them into the following four types according to the 2017 American Society of Echocardiography (ASE) guidelines: grade I (mild), grade II (moderate), grade III (moderate), and grade IV (severe). Both grade II and grade III are moderate. After image marking with the LabelMe software, a method using the Mask R-CNN algorithm based on deep learning (DL) was used to evaluate MR severity. We used the data from hospital A to build the artificial intelligence (AI) model and conduct internal verification, and we used the data from hospital B for external verification. According to severity, the accuracy of classification was 0.90, 0.89, and 0.91 for mild, moderate, and severe MR, respectively. The Macro F1 and Micro F1 coefficients were 0.91 and 0.92, respectively. According to grading, the accuracy of classification was 0.90, 0.87, 0.81, and 0.91 for grade I, grade II, grade III, and grade IV, respectively. The Macro F1 and Micro F1 coefficients were 0.89 and 0.89, respectively. Automatic assessment of MR severity is feasible with the Mask R-CNN algorithm and color Doppler electrocardiography images collected in accordance with the 2017 ASE guidelines, and the model demonstrates reasonable performance and provides reliable qualitative results for MR severity.

Construction of a Dye-Sensitized and Gold Plasmon-Enhanced Cathodic Photoelectrochemical Biosensor for Methyltransferase Activity Assay.

DNA methyltransferases may function as important biomarkers of cancers and genetic diseases. Herein, we develop a dye-sensitized and gold plasmon-enhanced cathodic photoelectrochemical (PEC) biosensor on the basis of p-type covalent organic polymers (COPs) for the signal-on measurement of M.SssI methyltransferase (M.SssI MTase). The cathodic PEC biosensor is constructed by the in situ growth of p-type COP films onto a glass coated with indium tin oxide and the subsequent assembly of biotin- and HS-labeled double-stranded DNA (dsDNA) probes onto the COP film via biotin-streptavidin interaction. The dsDNA probe contains the recognition sequence of M.SssI MTase. The COP thin films possess a porous ultrathin nanosheet structure with abundant active sites, facilitating the generation of a high photocurrent compared with the hydrothermally synthesized ones. The presence of DNA methyltransferases can prevent the digestion of restriction endonuclease HpaII, consequently inducing the introduction of gold nanoparticles (AuNPs) to the dsDNA probes via the S-Au bond and the intercalation of rhodamine B (RhB) into the DNA grooves to produce a high photocurrent due to the dye-photosensitized enhancement and AuNP-mediated surface plasmon resonance. However, in the absence of M.SssI MTase, HpaII digests the dsDNA probes, and neither AuNPs nor RhB can be introduced onto the electrode surface, leading to a low photocurrent. This cathodic PEC biosensor possesses high sensitivity and good selectivity, and it can screen the inhibitors and detect M.SssI MTase in serum as well.

Cobalt-Based Metal-Organic Frameworks for Adsorption of CO2 and C2 Hydrocarbons: Effect of Auxiliary Ligands with Different Functional Groups.

Recently, metal-organic frameworks (MOFs) have been investigated as potential materials for CO2 capture and light hydrocarbon storage/separation due to their high porosity, large surface area, and tunable skeleton structures. In this work, the six cobalt-based MOFs 1-6 were successfully synthesized under solvothermal conditions by a mixed-ligand strategy. 1 and 2 have the same framework structure with a topology of {42·5}2{44·510·67·76·8}, while the structures of the 3-6 frameworks are the same with a topology of {42·5}2{44·510·69·74·8}. The adsorption properties of these MOFs for CO2 and C2 hydrocarbons were then investigated, and the effect of the functional groups was discussed. The results revealed that the introduction of amino and bromo groups could effectively strengthen the adsorption performance.

Rhodium(III)-Catalyzed C(sp2)-H Chemoselective Annulation to O-Cyclized Isochromen-imines from Benzamides.

Through the development of ligands and reaction conditions, the Rh(III)-catalyzed selective annulation of benzamides with internal alkynes has been achieved to the formation of O-cyclized isochromen-imines. Various substituents are well-tolerated under mild reaction conditions. Density functional theory calculations indicate that silver carbonate could act as a Lewis acid to assist the ligand to improve the chemical selectivity of the reaction in a catalytic system.

Two series of Ln-MOFs by solvent induced self-assembly demonstrating the rapid selective sensing of Mg2+ and Fe3+ cations.

Two series of lanthanide-based metal-organic frameworks, namely {[Ln(BIPA-TC)0.5(DMA)2(NO3)]·DMA·H2O}n (1-Ln, Ln = Eu, Dy, Sm, Nd) and {[Ln2(BIPA-TC)1.5(DMA)3(H2O)2]·2DMA·2H2O}n (2-Ln, Ln = Eu, Dy, Sm, Nd), were successfully constructed via a solvent regulation strategy based on a π-electron rich tetra-carboxylate ligand (H4BIPA-TC). 1-Ln shows a 4-connected lvt topology with the point symbol of {42·84}, but 2-Ln displays a new 4,4,6-connected wxk1 topology with the point symbol of {43·83}4{46·66·83}2{86}. The solid-state luminescence property and the microporous nature of Eu-MOFs (1-Eu and 2-Eu) indicate that they can potentially be used as luminescent sensors. Fluorescence measurements indicate that Fe3+ exhibits the quenching effect for 1-Eu with the quenching efficiency of 93.1%. 2-Eu is the first MOF sensor for Mg2+ with the lowest detection limit of 1.53 × 10-10 mol L-1 and displays good recyclable capability. Simultaneously, in the presence of other metal ions (Ca2+, Mn2+, Co2+, Ni2+, Cu2+, Zn2+, Cd2+, Pd2+, Al3+, Cr3+and Fe3+), 2-Eu can maintain the selective sensing of Mg2+, indicating its potential for Mg2+ turn-on sensing.

Enhancement of visible-light photocatalytic activities of BiVO4 coupled with g-C3N4 prepared using different precursors.

Graphitic-like carbon nitride (g-C3N4) photocatalyst was synthesized by a facile chemical pyrolysis method, which was built on the self-condensation of different precursors to generate g-C3N4, e.g., melamine, urea, and thiocarbamide. And the different precursors produced a great influence on the photocatalytic activities of g-C3N4. Heterojunctions of g-C3N4 and BiVO4 were synthesized using a facile solvent evaporation method. The formation of BiVO4/g-C3N4 composites were confirmed by XRD, FT-IR, SEM, XPS, and UV-Vis DRS. The photocatalytic activities for RhB degradation were evaluated under visible-light irradiation. The photocatalytic activity of g-C3N4 prepared by urea was higher than that of g-C3N4 prepared by melamine and thiocarbamide, which was attributed to its favorable dispersibility, larger specific surface area, and higher oxidation capacity. The heterojunction composites exhibited higher photocatalytic activity than pure g-C3N4 or BiVO4. The results showed obvious removal efficiency for RhB, and the optimal sample with a BiVO4 content of 10% exhibited higher efficiency than pure g-C3N4 and BiVO4, and 10 wt%BiVO4/CN-U showed the highest photocatalytic activity. The enhanced photocatalytic activity of BiVO4/g-C3N4 composite can be attributed to the intimate coupling between the two host substrates, resulting in an efficient charge separation.

Zinc(II) and Copper(II) Hybrid Frameworks via Metal-Ion Metathesis with Enhanced Gas Uptake and Photoluminescence Properties.

The fabrication of metal-organic frameworks with controlled structure and desired properties is important but still a challenge. In this work, a zinc(II) framework, {[Zn3(L)2(DABCO)(H2O)]·9DMF} (named as Zn-1), has been synthesized based on [1,1':3',1″-terphenyl]-4,4″,5'-tricarboxylic acid (H3L) and 1,4-diazabicyclo[2.2.2]octane (DABCO), which is isostructural to the previously reported copper(II) analogue, {[Cu3(L)2(DABCO)(H2O)]·15H2O·9DMF} (named as Cu-1). Interestingly, hybrid zinc(II) and copper(II) bimetallic frameworks have been obtained via metal-ion metathesis and found to show enhanced adsorption and photoluminescence properties. Such a post-metal-ion metathesis method can be used to synthesize new and desired frameworks that could not be obtained by direct synthesis.

Fluorescent probes for "off-on" highly sensitive detection of Hg²âº and L-cysteine based on nitrogen-doped carbon dots.

Fluorescent nitrogen-doped carbon dots (NCDs) were synthesized by a facile, and low-cost one-step hydrothermal strategy using citric acid as carbon source and ammonia solution as nitrogen source for the first time. The obtained NCDs show stable blue fluorescence with a high quantum yield of 35.4%, along with the fluorescence lifetime of ca. 6.75 ns. Most importantly, Hg(2+) can completely quench the fluorescence of NCDs as a result of the formation of a non-fluorescent stable NCDs-Hg(2+) complex. Static fluorescence quenching towards Hg(2+) is proved by the Stern-Volmer equation, ultraviolet-visible absorption spectra, temperature dependent quenching and fluorescence lifetime measurements. Subsequently, the fluorescence of the NCDs-Hg(2+) system is completely recovered with the addition L-cysteine (L-Cys) owing to the dissociation of NCDs-Hg(2+) complex to form a more stable Hg(2+)-L-Cys complex by Hg(2+)-S bonding. Therefore, such NCDs can be used as an effective fluorescent "turn-off" probe for rapid, rather highly selective and sensitive detection of Hg(2+), with a limit of detection (LOD) as low as 1.48 nM and a linear detection range of 0-10 µM. Interestingly, NCDs-Hg(2+) system can be conveniently employed as a fluorescent "turn-on" sensor for highly selective and sensitive detection of L-Cys with a low LOD of 0.79 nM and a wide linear detection range of 0-50 µM. Further, the sensitivity of NCDs to Hg(2+) is preserved in tap water with a LOD of 1.65 nM and a linear detection range of 0-10 µM.

Ligand-Promoted Rh(III)-Catalyzed Coupling of Aryl C-H Bonds with Arylboron Reagents.

Rhodium(III)-catalyzed C-H arylation of arenes with phenylboronic acid pinacol esters has been achieved using a readily removable N-pentafluorophenylbenzamide directing group for the first time. The use of a bidentate phosphine ligand (Binap) significantly increased the yield of the cross-coupling of C-H bonds with organoboron reagents.

Synthesis, structure and adsorption properties of lanthanide-organic frameworks with pyridine-3,5-bis(phenyl-4-carboxylate).

Under solvothermal conditions, reactions of pyridine-3,5-bis(phenyl-4-carboxylic acid) (H2L) with lanthanide metal salts give rise to three new metal-organic frameworks (MOFs) with the formula {[Ln4(L)3(µ3-OH)4(H2O)4]·(NO3)2·solvent}n [Ln = Er (1), Yb (2) and Lu (3)]. The complexes were characterized by single crystal and powder X-ray diffraction, IR and thermogravimetric analyses. They have the same two-fold interpenetrating three-dimensional (3D) framework structures with [Ln4(COO)6(µ3-OH)4(H2O)4] clusters as secondary building units (SBUs) and a rare 6-connected lcy topology with the point (Schläfli) symbol of {3(3)·5(9)·6(3)}. Interestingly, 1-3 show selective and hysteretic sorption of CO2 over N2, and the photoluminescence properties of the complexes were also investigated.

Rh(iii)-catalyzed C-H olefination of N-pentafluoroaryl benzamides using air as the sole oxidant.

The oxidative olefination of a broad array of arenes and heteroarenes with a variety of activated and unactivated olefins has be achieved via a rhodium(iii)-catalyzed C-H activation reaction. The use of an N-pentafluorophenyl benzamide directing group is crucial for achieving catalytic turnovers in the presence of air as the sole oxidant without using a co-oxidant.

A porous metal-organic framework (MOF) with unusual 2D→3D polycatenation based on honeycomb layers.

A novel mixed-ligand 3D metal-organic framework (MOF), {Zn(2)(TMTA)(bipy)(0.5)(H(2)O)(2)·NO(3)·2DMF·H(2)O}(n) (1) (H(3)TMTA = 4,4',4''-(2,4,6-trimethylbenzene-1,3,5-triyl)tribenzoic acid, bipy = 4,4'-bipyridine, DMF = dimethylformamide), was constructed based on bipy-pillared honeycomb bilayers and showed the unusual 2D→3D polycatenation of bilayers.

Synthesis of decahydropyrrolo[2,1,5-cd]indolizine through consecutive [2 + 3] cycloadditions and 6-exo-trig cyclization.

Azomethine ylide formed from glycine methyl ester and cinnamaldehyde adds to N-phenylmaleimide to form pyrrolidine derivative, further treatment of which with cinnamaldehyde and N-phenylmaleimide affords the second [2 + 3] cycloaddition adduct, a pyrrolizine derivative with two styrenyl groups at the 3,5-positions. Addition of ICl to the pyrrolizine derivative results in the 6-exo-trig cyclization of the styrenyl groups to form a cycl[3.2.2]azine derivative. The reactions are highly stereoselective affording 11 chiral carbons in three steps. The structure of the cycl[3.2.2]azine derivative was determined by single-crystal X-ray analysis.