Performance of Anticorrosive Paint Systems for Carbon Steel in the Antarctic Marine Environment.

This study evaluated the behavior of three paint systems exposed to the Antarctic marine environment for 45 months compared to a control of uncoated carbon steel with a determined corrosion rate. At the study site, all environmental conditions, solar radiation, and the concentration of environmental pollutants (Cl- and SO2) were evaluated. The paint systems differed in terms of the primer and top coat. Coated samples were studied before and after exposure. They were evaluated visually and using SEM to determine adhesion, abrasion, and contact angle; using the Evans X-Cut Tape Test; using ATR-FTIR spectroscopy to analyze the state of aging of the top layer; and using electrochemical impedance spectroscopy (EIS) for coat protection characterization. The corrosion rate obtained for steel was 85.64 µm year-1, which aligned with a C5 environmental corrosivity category. In general, the evaluation in the period studied showed the paint systems had good adhesion and resistance to delamination, without the presence of surface rust, and exhibited some loss of brightness, an increase in the abrasion index, and a decrease in the percentage of reflectance due to aging. EIS showed good protection capability of the three coating schemes. In general, this type of paint system has not previously been evaluated in an extreme environment after 45 months of exposure to the environment. The results showed that the best behavior was found for the system whose top layer was acrylic-aliphatic polyurethane.

Atmospheric corrosion and impact toughness of steels: Case study in steels with and without galvanizing, exposed for 3 years in Rapa Nui Island.

We studied atmospheric corrosion on Rapa Nui Island, using galvanized and non-galvanized SAE 1020 steel samples exposed on racks. We also added Charpy samples of both materials to directly determine the effect of corrosion rate on these materials' impact toughness. The results indicated a correlation between corrosion rate and toughness loss in the studied materials. In the corrosion study, we could also demonstrate the effect from increased insular population growth on contaminants which aid atmospheric corrosivity. Results showed that atmospheric SO2 has tripled compared with similar corrosion studies done 20 years ago (Mapa Iberoamericano de Corrosión, MICAT), increasing corrosion rates. Our results show how human factors can influence changes in environmental variables that strengthen corrosion.

Hybrid Materials Based on Nanoparticles Functionalized with Alkylsilanes Covalently Anchored to Epoxy Matrices.

In this work, the surface modification of zinc oxide nanoparticles (ZnO-NPs) with 3-glycidyloxy-propyl-trimethoxysilane (GPTMS) was investigated. The ZnO-NPs were synthesized using the physical method of continuous arc discharge in controlled atmosphere (DARC-AC). The surface modification was carried out using a chemical method with constant agitation for 24 h at room temperature. This surface functionalization of zinc oxide nanoparticles (ZnO-NPs-GPTMS) was experimentally confirmed by infrared spectroscopy (FT-IR), TGA, and XRD, and its morphological characterization was performed with SEM. The increase in mechanical bending properties in the two final hybrid materials compared to the base polymers was verified. An average increase of 67% was achieved with a moderate decrease in ductility. In the case of compressive strength, they showed mixed results, maintaining the properties. With respect to thermal properties, it was observed that inorganic reinforcement conferred resistance to degradation on the base material, giving a greater resistance to high temperatures.

Antibacterial and cytotoxic evaluation of copper and zinc oxide nanoparticles as a potential disinfectant material of connections in implant provisional abutments: An in-vitro study.

OBJECTIVE: This study evaluates the antibacterial activity against mono and multispecies bacterial models and the cytotoxic effects of zinc oxide and copper nanoparticles(ZnO-NPs/Cu-NPs) in cell cultures of human gingival fibroblasts(HGFs). DESIGN: The antibacterial activities of ZnO-NPs and Cu-NPs against 4 bacteria species were tested according to their minimum inhibitory concentrations(MICs) and against mature multispecies anaerobic model by spectral confocal laser scanning microscopy. The viabilities and cytotoxic effects of ZnO-NPs and Cu-NPs to HGFs cell cultures were tested by MTT, LDH assays, production of ROS, and the activation of caspase-3. The results were analyzed using one-way ANOVA followed by Tukey tests, considering p < 0.05 as statistically significant. RESULTS: For all strains, MICs of ZnO-NPs and Cu-NPs were in the range of 78.3 µg/mL-3906 µg/mL and 125 µg/mL-625 ug/mL, respectively. In a multispecies model, a significant decrease in the total biomass volume(µ3) was observed in response to exposure to 125 µg/mL of each NPs for which there was bactericidal activity. Significant differences were found between the volumes of viable and nonviable biomass exposed to nanostructures with Cu-NPs compared to ZnO-NPs. Both NPs induced mitochondrial dose-dependent cytotoxicity, ZnO-NPs increases LDH release and intracellular ROS generation. Cu-NPs at a concentration of 50 µg/mL induced production of cleaved caspase-3, activating the apoptotic pathway early and at low doses. CONCLUSIONS: After 24 h, ZnO-NPs are biocompatible between 78-100 µg/mL and Cu-NPs below 50 µg/mL. Antibacterial activity in a monospecies model is strain dependent, and in a multispecies model was a lower doses after 10 min of exposure.