Strong transient magnetic fields induced by THz-driven plasmons in graphene disks.

Strong circularly polarized excitation opens up the possibility to generate and control effective magnetic fields in solid state systems, e.g., via the optical inverse Faraday effect or the phonon inverse Faraday effect. While these effects rely on material properties that can be tailored only to a limited degree, plasmonic resonances can be fully controlled by choosing proper dimensions and carrier concentrations. Plasmon resonances provide new degrees of freedom that can be used to tune or enhance the light-induced magnetic field in engineered metamaterials. Here we employ graphene disks to demonstrate light-induced transient magnetic fields from a plasmonic circular current with extremely high efficiency. The effective magnetic field at the plasmon resonance frequency of the graphene disks (3.5 THz) is evidenced by a strong ( ~ 1°) ultrafast Faraday rotation ( ~ 20 ps). In accordance with reference measurements and simulations, we estimated the strength of the induced magnetic field to be on the order of 0.7 T under a moderate pump fluence of about 440 nJ cm-2.

Phonon assisted electron emission from quasi-freestanding bilayer epitaxial graphene microstructures.

Electron emission from quasi-freestanding bilayer epitaxial graphene (QFEG) on a silicon carbide substrate is reported, demonstrating emission currents as high as 8.5µA, at ∼200 °C, under 0.3 Torr vacuum. Given the significantly low turn-on temperature of these QFEG devices, ∼150°C, the electron emission is explained by phonon-assisted electron emission, where the acoustic and optical phonons of QFEG causes carrier acceleration and emission. Devices of differing dimensions and shapes are fabricated via a simple and scalable fabrication procedure and tested. Variations in device morphology increase the density of dangling bonds, which can act as electron emission sites. Devices exhibit emission enhancement at increased temperatures, attributed to greater phonon densities. Devices exhibit emission under various test conditions, and a superior design and operating methodology are identified.

Real-time ultra-sensitive detection of SARS-CoV-2 by quasi-freestanding epitaxial graphene-based biosensor.

We report the rapid detection of SARS-CoV-2 in infected patients (mid-turbinate swabs and exhaled breath aerosol samples) in concentrations as low as 60 copies/mL of the virus in seconds by electrical transduction of the SARS-CoV-2 S1 spike protein antigen via SARS-CoV-2 S1 spike protein antibodies immobilized on bilayer quasi-freestanding epitaxial graphene without gate or signal amplification. The sensor demonstrates the spike protein antigen detection in a concentration as low as 1 ag/mL. The heterostructure of the SARS-CoV-2 antibody/graphene-based sensor is developed through a simple and low-cost fabrication technique. Furthermore, sensors integrated into a portable testing unit distinguished B.1.1.7 variant positive samples from infected patients (mid-turbinate swabs and saliva samples, 4000-8000 copies/mL) with a response time of as fast as 0.6 s. The sensor is reusable, allowing for reimmobilization of the crosslinker and antibodies on the biosensor after desorption of biomarkers by NaCl solution or heat treatment above 40 °C.

Surface potential and thin film quality of low work function metals on epitaxial graphene.

Metal films deposited on graphene are known to influence its electronic properties, but little is known about graphene's interactions with very low work function rare earth metals. Here we report on the work functions of a wide range of metals deposited on n-type epitaxial graphene (EG) as measured by Kelvin Probe Force Microscopy (KPFM). We compare the behaviors of rare earth metals (Pr, Eu, Er, Yb, and Y) with commonly used noble metals (Cr, Cu, Rh, Ni, Au, and Pt). The rare earth films oxidize rapidly, and exhibit unique behaviors when on graphene. We find that the measured work function of the low work function group is consistently higher than predicted, unlike the noble metals, which is likely due to rapid oxidation during measurement. Some of the low work function metals interact with graphene; for example, Eu exhibits bonding anomalies along the metal-graphene perimeter. We observe no correlation between metal work function and photovoltage, implying the metal-graphene interface properties are a more determinant factor. Yb emerges as the best choice for future applications requiring a low-work function electrical contact on graphene. Yb films have the strongest photovoltage response and maintains a relatively low surface roughness, ~5 nm, despite sensitivity to oxidation.

Polarity governs atomic interaction through two-dimensional materials.

The transparency of two-dimensional (2D) materials to intermolecular interactions of crystalline materials has been an unresolved topic. Here we report that remote atomic interaction through 2D materials is governed by the binding nature, that is, the polarity of atomic bonds, both in the underlying substrates and in 2D material interlayers. Although the potential field from covalent-bonded materials is screened by a monolayer of graphene, that from ionic-bonded materials is strong enough to penetrate through a few layers of graphene. Such field penetration is substantially attenuated by 2D hexagonal boron nitride, which itself has polarization in its atomic bonds. Based on the control of transparency, modulated by the nature of materials as well as interlayer thickness, various types of single-crystalline materials across the periodic table can be epitaxially grown on 2D material-coated substrates. The epitaxial films can subsequently be released as free-standing membranes, which provides unique opportunities for the heterointegration of arbitrary single-crystalline thin films in functional applications.

Epitaxial graphene quantum dots for high-performance terahertz bolometers.

Light absorption in graphene causes a large change in electron temperature due to the low electronic heat capacity and weak electron-phonon coupling. This property makes graphene a very attractive material for hot-electron bolometers in the terahertz frequency range. Unfortunately, the weak variation of electrical resistance with temperature results in limited responsivity for absorbed power. Here, we show that, due to quantum confinement, quantum dots of epitaxial graphene on SiC exhibit an extraordinarily high variation of resistance with temperature (higher than 430 MΩ K(-1) below 6 K), leading to responsivities of 1 × 10(10) V W(-1), a figure that is five orders of magnitude higher than other types of graphene hot-electron bolometer. The high responsivity, combined with an extremely low electrical noise-equivalent power (∼2 × 10(-16) W Hz(-1/2) at 2.5 K), already places our bolometers well above commercial cooled bolometers. Additionally, we show that these quantum dot bolometers demonstrate good performance at temperature as high as 77 K.

Tunable Terahertz Hybrid Metal-Graphene Plasmons.

We report here a new type of plasmon resonance that occurs when graphene is connected to a metal. These new plasmon modes offer the potential to incorporate a tunable plasmonic channel into a device with electrical contacts, a critical step toward practical graphene terahertz optoelectronics. Through theory and experiments, we demonstrate, for example, anomalously high resonant absorption or transmission when subwavelength graphene-filled apertures are introduced into an otherwise conductive layer. These tunable plasmon resonances are essential yet missing ingredients needed for terahertz filters, oscillators, detectors, and modulators.