ABSTRACT
The complete flax stem, which contains shives and technical fibres, has the potential to reduce the cost, energy consumption and environmental impacts of the composite production process if used directly as reinforcement in a polymer matrix. Earlier studies have utilised flax stem as reinforcement in non-bio-based and non-biodegradable matrices not completely exploiting the bio-sourced and biodegradable nature of flax. We investigated the potential of using flax stem as reinforcement in a polylactic acid (PLA) matrix to produce a lightweight, fully bio-based composite with improved mechanical properties. Furthermore, we developed a mathematical approach to predict the material stiffness of the full composite part produced by the injection moulding process, considering a three-phase micromechanical model, where the effects of local orientations are accounted. Injection moulded plates with a flax content of up to 20 V% were fabricated to study the effect of flax shives and full straw flax on the mechanical properties of the material. A 62% increase in longitudinal stiffness was obtained, resulting in a 10% higher specific stiffness, compared to a short glass fibre-reinforced reference composite. Moreover, the anisotropy ratio of the flax-reinforced composite was 21% lower, compared to the short glass fibre material. This lower anisotropy ratio is attributed to the presence of the flax shives. Considering the fibre orientation in the injection moulded plates predicted with Moldflow simulations, a high agreement between experimental and predicted stiffness data was obtained. The use of flax stems as polymer reinforcement provides an alternative to the use of short technical fibres that require intensive extraction and purification steps and are known to be cumbersome to feed to the compounder.
ABSTRACT
This review paper presents an overview of the state of the art on process-induced degradation of poly(lactic acid) (PLA) and the relative importance of different processing variables. The sensitivity of PLA to degradation, especially during melt processing, is considered a significant challenge as it may result in deterioration of its properties. The focus of this review is on degradation during melt processing techniques such as injection molding and extrusion, and therefore it does not deal with biodegradation. Firstly, the general processing and fundamental variables that determine the degradation are discussed. Secondly, the material properties (for example rheological, thermal, and mechanical) are presented that can be used to monitor and quantify the degradation. Thirdly, the effects of different processing variables on the extent of degradation are reviewed. Fourthly, additives are discussed for melt stabilization of PLA. Although current literature reports the degradation reactions and clearly indicates the effect of degradation on PLA's properties, there are still knowledge gaps in how to select and predict the processing conditions that minimize process-induced degradation to save raw materials and time during production.
ABSTRACT
This paper deals with predicting the effective thermal conductivity (ETC) of injection-moulded short fibre reinforced polymers (SFRPs) using two different homogenisation schemes: a scheme based on the dielectric theory for pseudo-oriented inclusions and a two-step homogenisation model based on the mean-field homogenisation approach. In both cases, the fibre orientation tensor (FOT) obtained from Autodesk Moldflow® simulation was used. The Moldflow FOT predictions were validated via structure tensor analysis of micro-computed X-ray tomography (micro-CT) scans of the part. In the dielectric-wise approach, the orientation of fibres was originally defined by a scalar parameter, which is related to the diagonal components of the FOT. In the two-step homogenisation approach, an interpolative model based on the Mori-Tanaka theory is used in the first step for calculating the ETC for the ideal case of unidirectional fibre alignment, followed by a second step in which orientation averaging based on the FOT inside each element is applied. The ETC was calculated using both schemes for the specific case of uniform fibre orientation distribution and at three different locations with non-identical FOTs of an injection-moulded SFRP part. The results are compared with each other and evaluated against the direct numerical simulation for the uniform fibre orientation and experimental measurements for the injection-moulded SFRP. This shows that while the two-step homogenisation can predict the ETC in the full range of orientations between the perfectly aligned and uniformly distributed fibres, the dielectric-wise approach is only capable of modelling the ETC when distributions are close to the two extreme ends of the orientation spectrum.
ABSTRACT
This article analyzes temperature fields and their variations in fused filament fabrication (FFF) from the filament entering the hot-end to the printed parts, aiming at a deeper understanding of the thermal process of this additive manufacturing technology. A standard E3D print head assembly was mounted on a robot arm for printing. A stable filament feeding region was determined with an upper limit in the volume flow rate at different nozzle temperatures. Within the limit, the steady-state temperature fields inside the hot-end were studied by a computational fluid dynamics model. Simulations indicated that the temperature became less homogeneous at higher flow rates, leading to a lower extrudate temperature at the nozzle outlet. These outlet temperatures were analyzed, validated, and used as input to simulate temperature variations in printed parts with a self-developed open-access numerical model. An interlayer time similarity rule was found in printing single-walled geometries, which specifies temperature similarities at the same interlayer time. The findings provide new insights into FFF processes, pointing out opportunities for improved production efficiency and scalability to large-scale manufacturing.