Active application of primer acid on acid-treated enamel: Influence on the bond effectiveness of self-etch adhesives systems.

AIM: Evaluate the composite-to-enamel bond after passive or active application of self-etching primer systems on polished or pre-etched enamel with phosphoric acid. MATERIALS AND METHODS: Two self-etch adhesives systems (SEAS) were used: Clearfil SE Bond and Easy Bond. Third human molars were divided into 8 groups (N = 10). The crown of each tooth was sectioned into halves and the mesial/distal surfaces were used. The adhesives were actively or passively applied on enamel with or without prior phosphoric-acid etching. Resin composite cylinders were built after adhesive application. After stored in relative humidity for 24 hr/37°C the specimens were subjected to microshear test in universal testing a machine at a crosshead speed of 0.5 mm/minute. The results were analyzed with three-way ANOVA and the Tukey test. The enamel-etching pattern was evaluated under SEM. RESULTS: The 2-step SEAS system presented significantly higher adhesive bond strength means (47.37 MPa) than the 1-step (36.87 MPa). A poor enamel- etching pattern was observed in active mode showing irregular and short resin tags, however there was not compromised the bond strength. CONCLUSION: Active or passive application produced similar values of bond strength to enamel regardless of enamel pretreatment and type of SEAS.

Nanoleakage of fiber posts luted with different adhesive strategies and the effect of chlorhexidine on the interface of dentin and self-adhesive cements.

The aim of this in vitro study was to evaluate the nanoleakage of fiber posts luted using different adhesive strategies and to investigate the effect of 2% chlorhexidine (CHX) on nanoleakage at the resin-dentin interfaces of self-adhesive cements. The self-adhesive and etch-and-rinse adhesive groups tested demonstrated similar results with regard to nanoleakage. Pretreatment with CHX promoted an adequate seal at the resin-dentin interface for self-adhesive cements.

Influence of photo-curing distance on bond strength and nanoleakage of self-etching adhesive bonds to enamel and dentin.

OBJECTIVES: To assess the influence of light-curing unit tip distance on the microtensile bond strength (µTBS) and nanoleakage of self-etching adhesives to enamel and dentin. MATERIALS AND METHODS: Flat buccal surfaces were prepared on 198 bovine incisors. The teeth were randomly assigned into nine groups for µTBS (n = 8) and nanoleakage (n = 3) testing according to the adhesive system (Clearfil Protect Bond, Clearfil Tri-S Bond or One Up Bond F Plus) and distance from the light-curing tip (0, 3 or 6 mm). The bonded samples were tested in tension (0.5 mm/min) and nanoleakage was analyzed using SEM. RESULTS: Clearfil Protect Bond exhibited the highest tensile strength on both enamel and dentin. Leakage was higher in samples exposed at a distance of 6 mm on enamel and 0 mm on dentin. One Up Bond F Plus experienced the greatest amount of nanoleakage on both substrates. CONCLUSIONS: Light-curing unit distance did not influence the µTBS of the adhesives, but nanoleakage increased on enamel samples when photoactivation occurred at a distance of 6 mm.

Fracture resistance of premolars with bonded class II amalgams.

This study evaluated the fracture resistance of maxillary premolars with MOD cavity preparation and simulated periodontal ligament. The teeth were restored with silver amalgam (G1), Scotchbond Multi-Purpose Plus and silver amalgam (G2) and Panavia F and silver amalgam (G3). After restorations were made, the specimens were stored at 37 degrees C for 24 hours at 100% humidity and submitted to the compression test in the Universal Testing Machine (Instron). The statistical analysis of the results (ANOVA and Tukey Test) revealed that the fracture resistance of group 2 (G2=105.720 kgF) was superior to those of groups 1 (G1=72.433 kgF) and 3 (G3=80.505 kgF) that did not differ between them.