Red rice starch modification - Combination of the non-thermal method with a pulsed electric field (PEF) and enzymatic method using α-amylase.

The objective of this study was to investigate the dual modification of red rice starch using pulsed electric field (PEF) and α-amylase, focusing on morpho-structural, thermal, and viscoamylographic properties. Native starch (Control) underwent various treatments: PEF at 30 kV cm-1 (PEF30), α-amylase at 9.0 U mg-1 (AA0), and a combination of both (PEF30 + α and α + PEF30). The PEF30 + α treatment exhibited the highest degree of digestion (10.66 %) and resulted in morphological changes in the starch granules, which became elongated and curved, with an increased average diameter of 50.49 µm compared to the control. The starch was classified as type A, with a maximum reduction in crystallinity of up to 21.17 % for PEF30. The deconvolution of FT-IR bands indicated an increase in the double helix degree (DDH) for PEF30 and AA0, while the degree of order (DO) was reduced for PEF30, AA0, and PEF30 + α. DSC analysis revealed significant modifications in gelatinization temperatures, particularly for PEF30, and these changes were supported by a reduction in gelatinization enthalpy (ΔH) of up to 28.05 % for AA0. These findings indicate that both individual and combined treatments promote a decrease in starch gelatinization and facilitate the process, requiring less energy. Differences were observed between the formulations subjected to single and alternating dual treatments, highlighting the influence of the order of PEF application on the structural characteristics of starch, especially when applied before the enzymatic treatment (PEF + α). Regarding the viscoamylographic parameters, it was observed that AA0 presented higher values than the control, indicating that α-amylase enhances the firmness of the paste. The double modification with PEF + α was more effective in reducing syneresis and starch retrogradation, leading to improvements in paste properties. This study provided significant insights into the modification of red rice starch using an efficient and environmentally friendly approach.

Enzyme immobilization technology as a tool to innovate in the production of biofuels: A special review of the Cross-Linked Enzyme Aggregates (CLEAs) strategy.

This review emphasizes the crucial role of enzyme immobilization technology in advancing the production of two main biofuels, ethanol and biodiesel, with a specific focus on the Cross-linked Enzyme Aggregates (CLEAs) strategy. This method of immobilization has gained attention due to its simplicity and affordability, as it does not initially require a solid support. CLEAs synthesis protocol includes two steps: enzyme precipitation and cross-linking of aggregates using bifunctional agents. We conducted a thorough search for papers detailing the synthesis of CLEAs utilizing amylases, cellulases, and hemicellulases. These key enzymes are involved in breaking down starch or lignocellulosic materials to produce ethanol, both in first and second-generation processes. CLEAs of lipases were included as these enzymes play a crucial role in the enzymatic process of biodiesel production. However, when dealing with large or diverse substrates such as lignocellulosic materials for ethanol production and oils/fats for biodiesel production, the use of individual enzymes may not be the most efficient method. Instead, a system that utilizes a blend of enzymes may prove to be more effective. To innovate in the production of biofuels (ethanol and biodiesel), enzyme co-immobilization using different enzyme species to produce Combi-CLEAs is a promising trend.

Immobilization of Thermomyces lanuginosus lipase on a new hydrophobic support (Streamline phenyl™): Strategies to improve stability and reusability.

This paper establishes an efficient protocol for the immobilization of Thermomyces lanuginosus lipase (TLL) on a hydrophobic resin, Streamline phenyl. The biocatalyst produced by TLL immobilization on Streamline phenyl resin was named iTLL. In addition, strategies to improve stability and reusability of iTLL were performed using polyethylenimine (PEI) or/and glutaraldehyde (GA), producing iTLL-GA, iTLL-PEI, iTLL-PEI-GA biocatalysts. The immobilization yield was about 50%, using 1 mg/g of enzyme loading, and the immobilized enzyme activity was about 77 U/g, achieving about 100% of recovered activity. Desorption assays of the enzyme from the support using 0.6% cetyltrimethylammonium bromide (CTAB) and thermal and operational stability assays were performed. Although iTLL-PEI-GA lost about 50% of its initial activity after PEI and GA modifications, it was the most thermally and operationally stable (increases its stability about 66% if comparing with soluble enzyme at 65 ºC and maintenance 90% of its initial activity after 5 cycles of pNPB hydrolysis at 25 °C and pH 7.0). Furthermore, it showed almost no desorption of enzyme molecules with 24 h of CTAB incubation. Moreover, the streamline phenyl demonstrated a high TLL loading potential, with no diffusion limitations up to 14 mg/g. These characteristics allow future application of the iTLL-PEI-GA biocatalyst in fluidized bed reactors.

Effect of enzymatic hydrolysis on digestibility and morpho-structural properties of hydrothermally pre-treated red rice starch.

The objective of this work was to evaluate the effects of enzymatic hydrolysis on digestibility and morphological and structural properties of hydrothermally pre-treated (HPT) red rice starch. The pre-treatments were performed in autoclave and cooking for the modification of rice grains and native starch. In vitro starch digestibility was performed consecutively and semi-simultaneously using α-amylase and amyloglucosidase. A first-order mathematical model was used to adjust the hydrolysis kinetic data, which made it possible to calculate the surface area, hydrolysis index, and glycemic index of the starch. Scanning electron microscopy images (SEM), Fourier transform infrared (FTIR) spectra and X-ray diffraction (XRD) were also performed to investigate the characteristics of the post-hydrolysis starch samples. The autoclaved starch HSS-A3, which was subjected to 121 °C/1.08 bar for 10 min, showed the highest in vitro digestibility values (80.08 %). Both starch samples showed increase of particle size and enzymatic digestibility after HPT. FTIR spectra of the starch samples showed that there was no appearance of new functional groups. However, XRD evidenced that HPT changed the intensity of the peaks and the type of crystallinity was changed for autoclaved starch (A3) from type A to Vh, with crystallinity ranging from 21.71 % to 26.42 %. The semi-simultaneous approach showed more advantages due to the highest in vitro digestibility as well as reducing the processing time and use of reagents.

Modification of red rice starch by a combination of hydrothermal pretreatments and α-amylase hydrolysis.

The objective of this study was to evaluate the modification of red rice starch by a combination of hydrothermal pretreatments and α-amylase hydrolysis. In vitro digestibility and the morphological, structural, functional, thermal, textural and rheological properties of red rice starch were evaluated. The starch submitted to autoclave (A3) obtained the highest hydrolysis yield (37.66 %) after 300 min. The morphological analysis showed that for the native starch, the granules presented a polyhedral shape and increased in diameter (2.36-394.12 µm) due to hydrothermal pre-treatments. α-Amylase (9 U mg-1) from Aspergillus oryzae modified the structure of red rice starch, presenting technological properties different from native starch. X-ray diffraction (XDR) were altered after the starch granules were cooked, showing a rupture in the amylose and amylopectin molecules, which justifies the greater absorption capacity of oil and milk. Cohesiveness, adhesiveness and apparent viscosity decreased according to HPT temperature and pressure, as well as α-amylase action.

Production of Lignocellulolytic Enzymes and Phenolic Compounds by Lentinus strigosus from the Amazon Using Solid-State Fermentation (SSF) of Guarana (Paullinia cupana) Residue.

The Amazon rainforest has a rich biodiversity, and studies of Basidiomycete fungi that have biomolecules of biotechnological interest are relevant. The use of lignocellulosic biomass in biotechnological processes proposes an alternative use, and also adds value to the material when employed in the bioconversion of agro-industrial waste. In this context, this study evaluate the production of lignocellulolytic enzymes (carboxymethylcellulases (CMCase), xylanase, pectinase, laccase) as well as phenolic compounds and proteases by solid-state fermentation (SSF) using the fungus Lentinus strigosus isolated from Amazon. The guarana (Paullinia cupana) residue was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). SSF was carried out with 60% humidification of the residue, at 30 °C, for 10 days. The lignocellulosic biomass presented fragmented structures with irregular shapes and porosities, and was mainly constituted by cellulose (19.16%), hemicellulose (32.83%), and lignin (6.06%). During the SSF, significant values of CMCase (0.84 U/g) on the 8th day, xylanase (1.00 U/g) on the 7th day, pectinase (2.19 U/g) on the 6th day, laccase (176.23 U/mL) on the 5th day, phenolic compounds (10.27 µg/mL) on the 1st day, soluble proteins (0.08 mg/mL) on the 5th day, and protease (8.30 U/mL) on the 6th day were observed. In general, the agro-industrial residue used provided promising results as a viable alternative for use as a substrate in biotechnological processes.

Purification of chitosanases produced by Bacillus toyonensis CCT 7899 and functional oligosaccharides production.

Chitooligosaccharides (COS) have a great potential to be used by pharmaceutical industry due to their many biological activities. The use of enzymes to produce them is very advantageous, however it still faces many challenges, such as discovering new strains capable to produce enzymes that are able to generate bioactive oligosaccharides. In the present study a purification protein protocol was performed to purify chitosanases produced by Bacillus toyonensis CCT 7899 for further chitosan hydrolysis. The produced chitooligosaccharides were characterized by mass spectroscopy (MS) and their antiedematogenic effect was investigated through carrageenan-induced paw edema model. The animals were treated previously to inflammation by intragastric route with COS at 30, 300 and 600 mg/kg. The purification protocol showed a good performance for the chitosanases purification using 0.20 M NaCl solution to elute it, with a 9.54-fold purification factor. The treatment with COS promoted a decrease of paw edema at all evaluated times and the AUC0-4h, proving that COS produced showed activity in acute inflammation like commercial anti-inflammatory Dexamethasone (corticosteroid). Therefore, the strategy used to purification was successfully applied and it was possible to generate bioactive oligosaccharides with potential pharmacological use.

Physicochemical characterization and in vitro antioxidant activity of hyaluronic acid produced by Streptococcus zooepidemicus CCT 7546.

Hyaluronic acid (HA) is a biopolymer with applications in different areas such as medicine and cosmetics. HA is currently either isolated from animal sources or produced by microbial fermentation. Animal HA presents some disadvantages such as high cost and risk of viral cross-species or another infectious agent. In the present study, we evaluated the physicochemical characteristics and in vitro antioxidant capacity of HA produced by Streptococcus zooepidemicus CCT 7546. In addition, commercial sodium hyaluronate (SH) from an animal source was used as control. The microbial HA yield after purification was 69.8 mg/L. According to Fourier transform infrared spectroscopy, it was seen that bacterial and animal HA spectra are overlapped. The thermogravimetric analysis revealed that microbial HA was more stable than its equivalent from the animal source. However, scanning electron microscopy indicates that the purification method used in the animal product was more effective. Microbial HA showed activity in total antioxidant capacity (14.02 ± 0.38%), reducing power (18.18 ± 6.43%), DPPH radical-scavenging (5.57 ± 0.23 kmol TE/g), and hydroxyl radical-scavenging (28.39 ± 2.40%) tests. Therefore, in vitro antioxidant tests demonstrated that the antioxidant action mechanism occurs through scavenging reactive oxygen species (ROS) and donating electrons/hydrogen atoms.

Evaluation of Blend Production of Cellulases and Xylanases Using Pretreated and Recycled Carnauba Straw.

Carnauba (Copernicia prunifera) is a Brazilian palm tree used for wax production, which usually generates a large amount of waste. This work evaluated the carnauba waste for cellulase and xylanase production using Trichoderma reesei CCT2768 through a solid-state fermentation (SSF). Carnauba waste was used in its crude form (C-IN), pretreated (C-P) with alkaline hydrogen peroxide (AHP), and also recycled after the SSF process (C-PR). C-IN, C-P, and C-PR were characterized by XRD, FTIR, and SEM. Cellulase and xylanase production was performed by SSF for 72 h, and the enzymatic extracts obtained were mixed each other in different concentrations. FPase, CMCase, and xylanase activities were determined. Trichoderma reesei CCT-2768 has shown high performance to produce cellulases and xylanases. Total cellulase, CMCase, and ß-glycosidase presented a highest activity when C-PPR1 (25% of C-PR and 75% of C-P) was used as a carbon source, with yield of 2.85 U/g, 41.21 U/g, and 2.80 U/g, respectively. The highest xylanase production was achieved when only the pretreated carnauba waste (C-P) was used, with an enzyme activity of 224.93 U/g. Carnauba has shown a promising carbon source capacity to induce the production of cellulolytic and xylanolytic enzymes by using T. reesei CCT2768, promoting the circular and ecofriendly economy, as well as a cost reduction, of the production process of these enzymes.

Kinetic study and characterization of surfactin production by Bacillus subtilis UFPEDA 438 using sugarcane molasses as carbon source.

The present study evaluated the surfactin production by Bacillus subtilis UFPEDA 438 using sugarcane molasses as a substrate. The effects of the cultivation conditions (temperature, agitation and aeration ratio) on the biosurfactant production and kinetic parameters were investigated. Characteristics of the biosurfactant were obtained after analyses of the emulsification index (EI) and critical micellar concentration (CMC) of the fermentation broth. The results showed that in relation to the product its formation kinetics is strongly affected by operational conditions. It was also observed that surfactin production can be partially dependent or fully independent on microbial growth. The maximum values of surfactin concentration (199.45 ± 0.13 mg/L) and productivity (8,187 mg/L.h) were obtained in the culture under cultivation time of 24 h, temperature of 36 °C, agitation of 100 rpm and aeration ratio of 0.4. Under optimal conditions, the fermentation broth achieved good emulsification capacity (EI >40%) and CMC value of 20.73 mg/L. The results revealed that Bacillus subtilis UFPEDA 438 is a good producer of biosurfactant and that sugarcane molasses is a viable substrate for the production of surfactin.

Lactose hydrolysis using ß-galactosidase from Kluyveromyces lactis immobilized with sodium alginate for potential industrial applications.

The present study aimed to evaluate the lactose hydrolysis conditions from "coalho" cheese whey using ß-galactosidase (ß-gal) produced by Kluyveromyces lactis immobilized with sodium alginate. Three sodium alginate-based immobilization systems were evaluated (0.5, 0.7, and 1% w/v) for maximizing the immobilization yield (Y), efficiency (EM), and recovered activity (ar). The lactose hydrolysis capacity of the immobilized form of ß-gal was determined, and simulated environments were used to assess the preservation of the immobilized enzyme in the gastrointestinal tract. The results showed that ß-gal immobilization with 1% (w/v) sodium alginate presented the best results (EM of 66%, Y of 41%, and ar of 65%). The immobilization system maintained the highest pH stability in the range between 5.0 and 7.0, with the highest relative activity obtained under pH 5 conditions. The temperature stability was also favored by immobilization at 50 °C for 30 min was obtained a relative activity of 180.0 ± 1.37%. In 6 h, the immobilized ß-gal was able to hydrolyze 46% of the initial lactose content. For the gastrointestinal simulations, around 40% of the activity was preserved after 2 h. Overall, the results described here are promising for the industrial applications of ß-galactosidase from K. lactis.

Potential of "coalho" cheese whey as lactose source for ß-galactosidase and ethanol co-production by Kluyveromyces spp. yeasts.

The present study evaluated the co-production of ß-galactosidase and ethanol by Kluyveromyces marxianus ATCC 36907 and Kluyveromyces lactis NRRL Y-8279 using as carbon source the lactose found on "coalho" cheese whey. Cheese whey was subjected to partial deproteinization, and physicochemical parameters were assessed. Cultivations were carried out in an shaker to evaluate two carbon/nitrogen (C:N) ratios. The best C:N ratio (1.5:1) was carried to 1.5-L bioreactor cultivation in order to increase co-production yields. The stability of ß-galactosidase was assessed against different temperatures and pH, and in the presence of metal ions. Concerning the co-production of ß-galactosidase and ethanol, K. lactis proved to be more efficient in both the C:N ratios, reaching 21.09 U·mL-1 of activity and 7.10 g·L-1 of ethanol in 16 h. This study describes the development of a viable and value-adding biotechnological process using a regional cheese by-product from Northeast Brazil for co-production of biomolecules of industrial interest.

Use of plasmids for expression of proteins from the genus Leishmania in Escherichia coli: current state and perspectives.

Leishmaniosis is caused by the protozoa of the genus Leishmania with a wide spectrum of clinical and epidemiological manifestations which are characterized into four clinical groups: cutaneous, mucocutaneous, diffuse cutaneous, and visceral. American visceral leishmaniosis (AVL) or visceral leishmaniosis (VL) has been known as the most severe form of the disease. However, despite the growing number of people exposed to the infection risk and the great effort done by the scientific community worldwide to significantly increase the knowledge about these diseases, there is no vaccine capable of preventing VL in humans. In this short review, we present some of the plasmids used for the expression of recombinant protein by Escherichia coli strains used mainly for the second generation of vaccines for leishmaniosis. It can be emphasized that currently, these vectors and hosts play an important role in developing vaccine strategies against the disease. Indeed, use of the E. coli BL21 (DE) strain is remarkable mainly due to its characteristics for being a stable protein producer as well as the use of histidine tags for antigen purification. KEY POINTS: • Plasmid vectors and E. coli will continue being important for studies about leishmaniosis. • Protein purification exploiting histidine tags is a key technique.

Evaluation of induction conditions for plasmid pQE-30 stability and 503 antigen of Leishmania i. chagasi expression in E. coli M15.

The present study aimed to evaluate the influence of induction conditions (IPTG concentration, temperature, and induction time) on the plasmid pQE-30 stability and 503 antigen expression of Leishmania i. chagasi in Escherichia coli M15. Batch cultures were performed at 37 °C and induced by the addition of different IPTG concentrations (0.01 to 1.5 mM). Subsequently, experiments were carried out at different temperatures (27 to 42 °C), evaluating the influence of induction time (0.5 to 6 h after the start of the culture). The results showed that IPTG toxicity caused a metabolic stress in the cells and, consequently, the microorganism growth reduced. The induction with IPTG may also be associated with the plasmid pQE-30 instability, due to metabolic burden imposed by the recombinant protein expression. The optimal conditions for 503 antigen expression of Leishmania i. chagasi in Escherichia coli M15 were an IPTG concentration of 1.0 mM, temperature of 37 °C, and induction time of 2 h. The maximum antigen concentration obtained was 0.119 ± 0.009 g/L, about seven times higher than the lowest concentration. Therefore, the results showed that 503 antigen can be produced in laboratory; however, it requires more studies to minimize the plasmid instability and improve to industrial scale.

Ethanol production from sugarcane bagasse: Use of different fermentation strategies to enhance an environmental-friendly process.

Ethanol production by simultaneous saccharification and fermentation (SSF) using sugarcane bagasse as substrate was developed using batch and fed-batch mode. Acid, alkali, hydrothermal and hydrogen peroxide pretreatments to the sugarcane bagasse were tested. Experiments were carried out to optimize the enzyme load of cellulases and ß-glucosidase. Four strains, two of Saccharomyces cerevisiae and two of Kluyveromyces marxianus yeast species were evaluate using SSF to produce ethanol. A kinetic study in bioreactor was carried out to optimize the SSF. The batch process was optimized using 1.0 g/L of inoculum, 15.0 FPU/g cellulose of cellulases and 6.0% of initial cellulose reaching 92.0% of theoretical ethanol yield after 18 h using the bagasse pretreate by acid-alkali and S. cerevisiae PE-2. The fed-batch process with enzyme load three times lower than that was used in batch process, obtained 88% of theoretical ethanol yield in 40 h. Therefore, the use of the lignocellulosic biomass (sugarcane bagasse) for producing a biofuel (ethanol) reduces the need for oil and is an environmental-friendly process.

Optimization of the 503 antigen induction strategy of Leishmania infantum chagasi expressed in Escherichia coli M15.

Leishmaniosis is a complex of diseases that can be fatal, if not given proper attention. Despite its relevance in the public health system, there is no vaccine capable of preventing the disease in humans so far and its treatment is expensive and aggressive to human health. The present study aims to optimize the induction parameters of the 503 Leishmania i. chagasi antigen expressed in recombinant Escherichia coli M15. The induction at different cell densities was evaluated in order to analyze the influence of the induction time on the yield of the protein of interest. In this segment, lactose and isopropyl-ß-d-thiogalactopyranoside (IPTG) were used as inducer molecules, using various concentrations: 0.1 g/L, 1.0 g/L, and 10 g/L for lactose and 20 µM, 100 µM, 500 µM, and 1000 µM for IPTG. The results presented that the concentration of IPTG that obtained the higher antigen levels was that of 100 µM (0.087 g/L), a 10-fold lower concentration than was being previously used in this type of system and for lactose, it was 1 g/L (0.016 g/L). Thus, the induction with 100 µM allowed obtaining the antigen with a concentration 5.6 times higher than the lactose induction maximum concentration.

Enhancing enzymatic hydrolysis of coconut husk through Pseudomonas aeruginosa AP 029/GLVIIA rhamnolipid preparation.

This work investigated the influence of chemical (Triton X-100) and biological surfactant preparation (rhamnolipids) in coconut husk hydrolysis that was subjected to pretreatment with acid-alkali or alkaline hydrogen peroxide. The natural and pretreated biomass was characterized using the National Renewable Energy Laboratory protocol analysis as well as X-ray diffraction and scanning electron microscopy. The results demonstrated that in terms of the total reducing sugars, there was no significant difference between the hydrolysis using Triton X-100 and rhamnolipids, regardless of the pretreatment. A cellulosic conversion value as high as 33.0% was obtained in experiments with rhamnolipids. The coconut husk was observed to be a potential biomass that could produce second generation ethanol, and the rhamnolipid preparation can be used to support for the enzymatic hydrolysis, enhancing the advantage of cellulose conversion into glucose over chemical surfactants because it is an environmentally friendly approach.

Mathematical modeling of the whole expanded bed adsorption process to recover and purify chitosanases from the unclarified fermentation broth of Paenibacillus ehimensis.

In this study, a general rate model was applied to the entire process of expanded bed adsorption chromatography (EBAC) for the chitosanases purification protocol from unclarified fermentation broth produced by Paenibacillus ehimensis using the anionic adsorbent Streamline® DEAE. For the experiments performed using the expanded bed, a homemade column (2.6cm×30.0cm) was specially designed. The proposed model predicted the entire EBA process adequately, giving R2 values higher than 0.85 and χ2 as low as 0.351 for the elution step. Using the validated model, a 33 factorial design was used to investigate other non-tested conditions as input. It was observed that the superficial velocity during loading and washing steps, as well as the settled bed height, has a strong positive effect on the F objective function used to evaluate the production of the purified chitosanases.

Single-step purification of chitosanases from Bacillus cereus using expanded bed chromatography.

A chitosanase-producing strain was isolated and identified as Bacillus cereus C-01. The purification and characterization of two chitosanases were studied. The purification assay was accomplished by ion exchange expanded-bed chromatography. Experiments were carried out in the presence and in the absence of cells through different expansion degree to evaluate the process performance. The adsorption experiments demonstrated that the biomass does not affect substantially the adsorption capacity of the matrix. The enzyme bound to the resin with the same extent using clarified and unclarified broth (0.32 and 0.30 U/g adsorbent, respectively). The fraction recovered exhibited 31% of the yield with a 1.26-fold increase on the specific activity concerned to the initial broth. Two chitosanases from different elution steps were recovery. Chit A and Chit B were stable at 30-60°C, pH 5.5-8.0 and 5.5-7.5, respectively. The highest activity was found at 55°C, pH 5.5 to Chit A and 50°C, pH 6.5 to Chit B. The ions Cu(2+), Fe(2+) and Zn(2+) indicated inhibitory effect on chitosanases activities that were significantly activated by Mn(2+). The methodology applied in this study enables the partial purification of a stable chitosanase using a feedstock without any pre-treatment using a single-step purification.

Recovery and purification of chitosanase produced by Bacillus cereus using expanded bed adsorption and central composite design.

This study presents a system for expanded bed adsorption for the purification of chitosanase from broth extract in a single step. A chitosanase-producing strain was isolated and identified as Bacillus cereus C-01 and used to produce chitosanases. The expanded bed adsorption conditions for chitosanase purification were optimized statistically using STREAMLINE(TM) DEAE and a homemade column (2.6 × 30.0 cm). Dependent variables were defined by the quality criteria purification factor (P) and enzyme yield to optimize the chromatographic process. Statistical analyses showed that the optimum conditions for the maximum P were 150 cm/h load flow velocity, 6.0 cm settled bed height, and 7.36 cm distributor height. Distributor height had a strong influence on the process, considerably affecting both the P and enzyme yield. Optimizing the purification variables resulted in an approximately 3.66-fold increase in the P compared with the value under nonoptimized conditions. This system is promising for the recovery of chitosanase from B. cereus C-01 and is economically viable because it promotes the reduction steps.