ABSTRACT
Covalent organic frameworks (COFs) are class of porous coordination polymers made up of organic building blocks joined together by covalent bonding through thermodynamic and controlled reversible polymerization reactions. This review discussed versatile applications of COFs for remediation of wastewater containing dyes, emphasizing the advantages of both pristine and modified materials in adsorption, membrane separation, and advanced oxidations processes. The excellent performance of COFs towards adsorption and membrane filtration has been centered to their higher crystallinity and porosity, exhibiting exceptionally high surface area, pore size and pore volumes. Thus, they provide more active sites for trapping the dye molecules. On one hand, the photocatalytic performance of the COFs was attributed to their semiconducting properties, and when coupled with other functional semiconducting materials, they achieve good mechanical and thermal stabilities, positive light response, and narrow band gap, a typical characteristic of excellent photocatalysts. As such, COFs and their composites have demonstrated excellent potentialities for the elimination of the dyes.
ABSTRACT
This study reports a simple new technique for the preparation of novel hexagonal-shaped mixed metal oxides (MMO) nanorods using Zn/Al-layered double hydroxide (LDH) as a precursor for dye-sensitized solar cell (DSSC) application. The effect of the Zn to Al molar ratio demonstrated a sound correlation between the obtained nanorods' diameter and the fabricated DSSCs efficiency. Additionally, the optical behavior of the fabricated MMO film as well as the absorption enhancement due to the utilized dye are also demonstrated; a cut-off phenomenon at around 376 nm corresponds to the attained hexagonal nanorods. The open-circuit voltage augmented noticeably from 0.6 to 0.64 V alongside an increase in the diameter of nanorods from 64 to 80 nm. The results indicated that an increment in the diameter of the nanorods is desirable due to the enhanced surface area through which a higher amount of dye N719 was loaded (0.35 mM/cm2). This, in turn, expedited the transport of electrons within the MMO matrix resulting in an advanced short-circuit current. Of the devices fabricated, ZA-8 exhibited the highest fill factor and efficiency of 0.37% and 0.69%, respectively, because of its boosted short-circuit current and open-circuit voltage.
ABSTRACT
This paper presents guidelines for the calibration of radiation beams that were issued by the International Atomic Energy Agency (IAEA TRS 398), the American Association of Physicists in Medicine (AAPM TG 51) and the German task group (DIN 6800-2). These protocols are based on the use of an ionization chamber calibrated in terms of absorbed dose to water in a standard laboratory's reference quality beam, where the previous protocols were based on air kerma standards. This study aims to determine uncertainties in dosimetry for electron beam radiotherapy using internationally established high-energy radiotherapy beam calibration standards. Methods: Dw was determined in 6-, 12- and 18 MeV electron energies under reference conditions using three cylindrical and two plane-parallel ion chambers in concert with the IAEA TRS 398, AAPM TG 51 and DIN 6800-2 absorbed dose protocols. From mean measured Dw values, the ratio TRS 398/TG 51 was found to vary between 0.988 and 1.004, while for the counterpart TRS 398/DIN 6800-2 and TG 51/DIN 6800-2, the variation ranges were 0.991-1.003 and 0.997-1.005, respectively. For the cylindrical chambers, the relative combined uncertainty (k = 1) in absorbed dose measurements was 1.44%, while for the plane-parallel chambers, it ranged from 1.53 to 1.88%. Conclusions: A high degree of consistency was demonstrated among the three protocols. It is suggested that in the use of the presently determined dose conversion factors across the three protocols, dose intercomparisons can be facilitated between radiotherapy centres.
ABSTRACT
Breast and colon carcinomas are two types of common cancers which lead to cancer-related deaths. Due to their cytotoxic potential against cancer cells, recently many studies of copper nanoparticles (CuNPs) have been conducted. In the current work, we aim to evaluate the cytotoxic and apoptosis-inducing effects of CuNPs on the human breast (MCF-7) and colon (LoVo) cancer cells. CuNPs were prepared in starch-stabilizing aqueous solution by electroless deposition technique in alkaline tartrate bath using formaldehyde as the reducing agent of copper sulfate. The obtained CuNPs were characterized by SEM, TEM, and XRD to confirm the particle size, morphology, and chemical composition. Standard colorimetric MTT and LDH assays were used to estimate the cytotoxic effect of CuNPs on MCF-7 and LoVo cells. Furthermore, CuNP-treated cells undergoing apoptosis were assessed based on the expression of apoptosis-related genes using qRT-PCR. The results indicate that the mean particle size of the synthesized CuNPs was ~ 50-60 nm, and they were spherical in shape with mainly the chemical structure of the copper metallic phase. MTT assay revealed that CuNPs induced cytotoxicity in tested cells with IC50 rates of 16.4 (in MCF-7) and 21.6 µg/ml (in LoVo). Moreover, qRT-PCR analysis showed that CuNPs caused a significant increment of Bax, P53, and Caspases 9, 8, and 3 genes. Overall, the anticancer potential of prepared CuNPs were reported through apoptotic induction which highlight the potential use of CuNPs as an efficient anticancer agent.