Life cycle assessment and life cycle cost analysis of anion exchange and granular activated carbon systems for remediation of groundwater contaminated by per- and polyfluoroalkyl substances (PFASs).

Anion exchange resin (AER) and granular activated carbon (GAC) have emerged as prominent technologies for treatment of waters contaminated with per- and polyfluoroalkyl substances (PFASs). This study compares the life cycle environmental impacts and life cycle costs of remediating PFAS-contaminated groundwater with these competing technologies, using field pilot data to inform model inputs. Comparative analysis indicates that AER systems employing single-use "PFAS-selective" resins have lower environmental impacts and costs than systems using regenerable resins or GAC adsorbents, supporting its use in future remediation efforts. Use of GAC operated as a single-use adsorbent led to the highest emissions as well as the highest treatment costs, with thermally-reactivated GAC proving to be less impactful than regenerable AER treatment. Sensitivity analyses highlighted the dominance of media usage rate (MUR), which is highly dependent on the selected PFAS treatment goals, to determine environmental impacts and costs over a 30-year system life cycle. Selection of very stringent changeout criteria (e.g., detection of any PFASs in effluent) significantly reduces the advantages of single-use resins. For regenerable AER, environmental impacts were dominated by management of the PFAS-contaminated brine/co-solvent waste stream used to regenerate the adsorbent, as well as the cosolvent content of the regenerant mixture and the cosolvent recovery efficiency achieved via on-site distillation. High impacts estimated for GAC adsorption, the result of high MUR relative to ion exchange media, can be significantly reduced if spent adsorbents are reused after thermal reactivation, but impacts are still greater than those predicted for single-use ion exchange systems. Findings are expected to hold across a range of diverse sites, including drinking water systems treating more dilute sources of PFAS contamination, as PFAS breakthrough was not found to be highly sensitive to sourcewater PFAS concentrations.

Pilot study comparison of regenerable and emerging single-use anion exchange resins for treatment of groundwater contaminated by per- and polyfluoroalkyl substances (PFASs).

This study reports the results of an 8-month pilot study comparing both regenerable and emerging single-use anion exchange resins (AERs) for treatment of per- and polyfluoroalkyl substances (PFASs) at a source zone impacted by historical use of aqueous film-forming foam (AFFF). Two regenerable (Purolite A860 and A520E) and three single-use (Purolite PFA694E, Calgon CalRes 2301, and Dowex PSR2+) AERs were tested in parallel, collecting effluent samples after treatment for 30-sec and 2-min total empty bed contact time (EBCT). Results demonstrate that single-use AERs significantly outperform regenerable resins, particularly for treatment of long-chain perfluoroalkyl carboxylic acids (PFCAs) and perfluoroalkyl sulfonic acids (PFSAs). No detectable concentrations of ≥C7 PFCAs or PFSAs were observed within 150,000 bed volumes (BVs) after treatment with the single-use resins (2-min EBCT). Analysis of effluent samples following 30-sec EBCT treatment shows that even the shortest-chain PFSAs do not reach 50% breakthrough within the first 350,000 BVs, though differences in removal of short-chain PFCAs was less dramatic. The regenerable polyacrylic A860 resin performed very poorly compared to all polystyrene resins, with >90% breakthrough of all PFASs occurring within 10,000 BVs. The greater affinity of polystyrene resins is attributed to increased hydrophobic interactions in addition to electrostatic ion exchange. Analysis of breakthrough profiles reveals empirical correlation with ion exchange affinity coefficients (logKex) measured in batch experiments. Postmortem analysis of PFASs extracted from spent resins revealed chromatographic elution behavior and competition among PFASs for adsorption to the resins. PFSAs and long-chain PFCAs were preferentially adsorbed to earlier sections in the AER columns, whereas short-chain PFCAs were competitively displaced towards the later sections of the columns and into the effluent, consistent with effluent concentrations of the latter structures exceeding influent values. These results provide insights into the mechanisms that govern PFAS adsorption to AERs in real multisolute groundwater matrices and support findings from other diverse sites regarding PFAS affinity, elution behavior, and competition for exchange sites.

Life cycle environmental impacts of regeneration options for anion exchange resin remediation of PFAS impacted water.

Although anion exchange resin (AER) treatment is considered an effective technology for removing per- and polyfluoroalkyl substances (PFASs) from impacted water, the environmental impacts associated with AER regeneration have not been systematically explored. In particular, the trade-offs of altering the composition of the regeneration solution and disposing of or recycling the waste regeneration solution are not known. To fill these important gaps in the literature, this research conducted a comparative life cycle assessment (LCA) of an AER-based PFAS remediation system with different regeneration scenarios including disposing of waste regeneration solution via incineration, reusing the organic cosolvent and brine fractions of the waste regeneration solution, and altering the composition of the regeneration solution to avoid organic cosolvent or NaCl. The results show that disposing of waste regeneration solution via incineration, without recycling organic cosolvent or brine, had the greatest environmental impact, and that incineration accounted for the greatest impact among contributing processes. Recycling of the cosolvent (or cosolvent and brine) fraction of the waste regeneration solution resulted in lower environmental impacts due to reduced mass of waste disposed of via incineration. Replacing NaCl in the brine with an alternative salt resulted in higher environmental impacts, with salts derived from chemical production, such as ammonium chloride and potassium carbonate, showing the largest increases in impacts. The results of this research highlight the importance of understanding the fate of PFASs during incineration, and the need for PFAS destruction technologies that can be coupled to AER regeneration to avoid incineration.

Anion exchange resin removal of per- and polyfluoroalkyl substances (PFAS) from impacted water: A critical review.

A key gap in the literature on the treatment of per- and polyfluoroalkyl substances (PFAS) in impacted water is the absence of a review article dedicated to anion exchange resin (AER) treatment. This gap is important because previous research has consistently shown adsorption by AER to be one of the most effective treatment processes for PFAS removal from impacted water, and AER is one of the most commonly deployed technologies in the field. Given the scope of the previous review articles on PFAS removal by various adsorbent types, the sections on AER do not explore the full depth of PFAS and AER interactions nor cover the breadth of AER testing conditions. Accordingly, the goal of this paper was to critically review the available peer-reviewed literature on PFAS removal from water by AER. The specific objectives of the review were to synthesize the previous literature results on (1) batch adsorption behavior, (2) impact of water chemistry conditions, (3) continuous-flow adsorption, (4) adsorption modeling, (5) regeneration, and (6) weak-base AER. Following from critical review of the literature, the future research priorities discussed include: (i) improving the underlying science that governs PFAS-resin interactions, (ii) improving methods for resin regeneration and management of PFAS-contaminated concentrate streams, and (iii) comparative life cycle environmental and economic analyses for ion exchange treatment systems relative to competing technologies.

Removal of Per- and Polyfluoroalkyl Substances (PFASs) in Aqueous Film-Forming Foam (AFFF) Using Ion-Exchange and Nonionic Resins.

Despite benefits to the firefighting industry, the release of per- and polyfluoroalkyl substances (PFASs) from aqueous film-forming foam (AFFF) into aquatic systems poses significant risks to human health and other organisms. While anion-exchange technologies have proven to be effective for removing perfluoroalkyl acids (PFAAs) from water, their effectiveness for removing the diverse PFAS structures discovered in AFFF remains unknown. Here, we report on the adsorption of 75 PFASs, including 63 polyfluorinated substances, in a diluted AFFF mixture using 14 commercially available ion-exchange (IX)/nonionic resins and granular activated carbon (GAC). Results showed that anion-exchange resins (AERs) exhibited significant adsorption of PFASs compared to cation-exchange resins (CERs), nonionic resins (NIRs), and GAC regardless of the PFAS's predicted charge. Isotherm data showed that macroporous AERs have a higher PFAS adsorption capacity compared to gel-type AERs. Cross-correlation comparison of PFAS/Cl- selectivity coefficients (Kex) for each PFAS-AER combination showed that the hydrophobicity of the AER functional group, and polymer matrix played a dominant role in determining resin affinity for PFASs. PFAS structural characteristics also significantly affected adsorption, with increasing chain length and a net negative charge increasing the extent of adsorption. Results from this study provide guidelines for the selection of resins to adsorb a wider range of PFASs and meaningful insights for the development of quantitative models for IX treatment of AFFF-impacted water.

Selective oxidation of colour-inducing constituents in raw sugar cane juice with potassium permanganate.

Colour removal in raw sugar remains a crucial but expensive process in the sugar industry. In this report, permanganate (MnO4-) oxidation is explored as an alternative method to remove colour-inducing constituents in sugar cane juice/produced raw sugar. Experiments indicated alum, an inexpensive coagulant, was able to remove residual Mn species produced after MnO4- treatment. The optimal dosages of MnO4- and alum for decoloration of a 17 wt% raw sugar solution (70 °C) was found to be 4 mM and 2 g/l, respectively. Removal of colour and Mn removal were further improved at ambient temperature. Sucrose, the major component of raw sugar, was not affected during treatment with MnO4- and alum. Two-phase kinetic behaviour for MnO4- oxidation was observed, where an initial rapid oxidation phase is followed by a second slower reaction phase. These results suggest permanganate oxidation is a promising alternative for accomplishing the decoloration of raw sugar solutions.