Hydrogen iodide (HI) neutral beam etching characteristics of InGaN and GaN for micro-LED fabrication.

We investigated the etching characteristics of hydrogen iodide (HI) neutral beam etching (NBE) of GaN and InGaN and compared with Cl2NBE. We showed the advantages of HI NBE versus Cl2NBE, namely: higher InGaN etch rate, better surface smoothness, and significantly reduced etching residues. Moreover, HI NBE was suppressed of yellow luminescence compared with Cl2plasma. InClxis a product of Cl2NBE. It does not evaporate and remains on the surface as a residue, resulting in a low InGaN etching rate. We found that HI NBE has a higher reactivity with In resulting in InGaN etch rates up to 6.3 nm min-1, and low activation energy for InGaN of approximately 0.015 eV, and a thinner reaction layer than Cl2NBE due to high volatility of In-I compounds. HI NBE resulted in smoother etching surface with a root mean square average (rms) of 2.9 nm of HI NBE than Cl2NBE (rms: 4.3 nm) with controlled etching residue. Moreover, the defect generation was suppressed in HI NBE compared to Cl2plasma, as indicated by lower yellow luminescence intensity increase after etching. Therefore, HI NBE is potentially useful for high throughput fabrication ofµLEDs.

Effect of photofunctionalization on titanium bone-implant integration in ovariectomized rats.

Osteoporosis is considered a risk factor for osseointegration during implant treatment. Photofunctionalization of titanium has been shown to improve bone-based cell adhesion, proliferation, and functional expression, increasing the bone-implant contact rate and bone-implant integration strength. This study aimed to test the hypothesis that photofunctionalization is effective for implant fixation using an osteoporosis rat model. In the biomechanical push-in test, the bone-implant integration strength of the photofunctionalization treatment group was 1.53 times that of the control group (p<0.05). These values implied that photofunctionalization restored the ovariectomy-induced low bone-implant integration strength to normal states. In the micro-CT analysis, the BV/TV of the photofunctionalization treatment group was 1.32 times that of the control group (p<0.05). These values implied that photofunctionalization restored the ovariectomy-induced low peri-implant bone formation to normal states. These results indicate that photofunctionalization treatment increased peri-implant bone formation and bone-implant integration strength in ovariectomized rats.

Clostridium perfringens sepsis after pancreatoduodenectomy: a case report.

BACKGROUND: Clostridium perfringens sepsis associated with massive intravascular hemolysis has an extremely poor prognosis. We here report a case of C. perfringens sepsis associated with massive intravascular hemolysis that developed secondary to a post-pancreaticoduodenectomy (PD) hepatic abscess. CASE PRESENTATION: A 70-year-old man with Type 2 diabetes underwent PD for an ampulla of Vater carcinoma. His postoperative course was uneventful. He was discharged on the 16th post-operative day (POD 16) after confirming no major abnormalities on abdominal contrast computed tomography (CT) on POD 14 or laboratory results on POD 16. Two days after discharge, he was readmitted because of fever and chills. Laboratory tests showed only a mild inflammatory reaction (white blood cell count, 11,980/mm3; C-reactive protein, 2.07 mg/dL). Abdominal CT showed an irregular, approximately 20-mm diameter, low-density area in the liver S6 region that had not been seen on a recent previous scan. We initially suspected postoperative cholangitis associated with biliary reconstruction and started empirical treatment with sulbactam/ampicillin after drawing blood for culture. Eight hours after admission, he developed septic shock with body temperature 40.0 â„ƒ and blood pressure 70/40 mm Hg. Laboratory findings showed a severe inflammatory reaction, severe anemia, and massive hemolysis (white blood cell count, 37,400/mm3; hemoglobin, 7.7 g/dL; total bilirubin, 8.05 mg/dL; direct bilirubin, 2.66 mg/dL; and lactate dehydrogenase, 1686 U/L). Hemoglobinuria was noted in the urinary catheter output. Repeat CT 9 h after admission showed the low-density area in S6 had become a gas-forming abscess. C. perfringens sepsis was strongly suspected on the basis of these findings and the abscess was drained percutaneously immediately after its diagnosis. His vital signs improved dramatically and he recovered within 24 h. Blood and abscess cultures grew C. perfringens 4 days after admission, leading to a definitive diagnosis of C. perfringens sepsis associated with massive intravascular hemolysis. He was discharged 18 days after admission. His sepsis has not recurred. CONCLUSIONS: Clostridium perfringens infection should be considered in patients who have undergone PD and present with gas-forming hepatic abscesses and/or sepsis associated with intravascular hemolysis. Prompt aggressive treatment is crucial, because C. perfringens infections can cause death within hours.

Surface analysis of titanium disks with strontium coating.

Peri-implantitis is one of the most common complications after dental implant placement. Researchers have demonstrated that the peri-implantitis tends to occur around dental implants with a rough surface rather than those with a smooth surface. We aimed to investigate the ability of a smooth titanium (Ti) surface containing strontium (Sr) to enhance bone formation as a result of strontium's capacity to support osteoblast proliferation and differentiation. A thin titanium oxide film was formed on an as-mirror polished Ti surface by dipping in 5% sodium hypochlorite (NaOCl) solution for 24 h, followed by thermal treatment at 350°C. The Ti surface was then treated with 1% strontium nitrate (Sr(NO3)2) solution and turned in spin coater. The surface morphology, chemical composition, and release of strontium ions (Sr2+) were evaluated. The results demonstrate that strontium in the form of Sr2+ was successfully doped into the titanium dioxide (TiO2) film by this simple chemical treatment.

Chemical interaction of 4-META with enamel in resin-enamel bonds.

X-ray photoelectron spectroscopy (XPS) is used to analyze 4-META resin and enamel that are debonded at an adhesive interface. The XPS spectra showed two chemical states for Ca: one resulted from Ca of hydroxyapatite and the other, an unknown chemical state, suggested that Ca was chemically bonded with 4-META. We postulate that for a chemical reaction of 4-META and hydroxyapatite, the chemical structure of carboxyl groups will resemble that of calcium phthalate. Hence, calcium phthalate was used as a reference material. Additionally, the spectra obtained from the adhesive interface and the mixture of calcium phthalate with hydroxyapatite particles were compared using peak deconvolution analysis. XPS analysis revealed that the chemical bond of 4-META with enamel resembled the chemical state of Ca in calcium phthalate. Consequently, we suggest that Ca of the enamel and the carboxyl group of 4-META were chelate-bonded at the interface.

Laparoscopic excision for small intestinal mesenteric tumour diagnosed Schloffer tumour.

This report presents a case of Schloffer tumour at the small intestinal mesentery, mimicking a malignant tumour, treated laparoscopically. Six years prior, a 57-year-old woman underwent laparoscopic salpingo-oophorectomy for a benign, cystic, ovarian tumour, but she had no history of malignancy. She was treated at an outpatient clinic for gastrointestinal complaints and was relieved of these symptoms. Abdominal computed tomography showed an incidental mesenteric tumour of the small intestine, tending toward growth. Due to the tumour's malignant potential, laparoscopic examination was performed. A spherical tumour with a base in the jejunum mesentery was observed. It was removed without damage. The post-operative course was uneventful, and the patient was discharged 3 days after the operation without complications. Histological diagnosis showed this to be a Schloffer tumour, but no malignancy was observed. Unidentified intraperitoneal tumours in patients with surgical histories may be Schloffer tumours, and this should be kept in mind.

In vitro evaluation of NaOCl-mediated functionalization of biologically aged titanium surfaces.

The aim of this study was to evaluate the NaOCl-mediated biofunctionalization of titanium surfaces. Titanium disks stored for 2 weeks were immersed in 5% NaOCl solution for 24 h. A disk immersed in distilled water for 24 h was used as a control. X-ray photoelectron spectrometer assay of the titanium surface after NaOCl treatment demonstrated that organic contaminants containing carbon and nitrogen were removed and the number of hydroxyl groups increased. The NaOCl treatment substantially converted the titanium surface to superhydrophilic status (θ<5°), which resulted in an increased number of attached cells and enhanced cell spreading on the NaOCl-treated surfaces. These results indicate that biofunctionalization of the biologically degraded titanium surfaces can be achieved by chemical surface treatment with 5% NaOCl. The mechanism for desorption of strongly adsorbed organic molecules with polar groups such as amino and aldehyde groups from titanium surfaces by ClO- was elucidated.

Protective Effects of GIC and S-PRG Filler Restoratives on Demineralization of Bovine Enamel in Lactic Acid Solution.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for six days at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after six days of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after six days were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.

Stereolithographic Surgical Guide with a Combination of Tooth and Bone Support: Accuracy of Guided Implant Surgery in Distal Extension Situation.

A distal free-end situation could result in insufficient stability of the surgical guide, and could reduce accuracy of the static guided implant surgery (sGIS). The purpose of this study was to investigate the accuracy of sGIS using a combination tooth-and-bone supported stereolithographic (SLA) surgical guide in distal extension situation. Thirty dentists, each placed three implants at the Federal Dentaire Internationale (FDI) teeth positions #46, #47 (a distal extension situation), and #36 (a single tooth gap) via the surgical guide on a model fixed to a manikin. Pre- and post-operative computed tomography (CT) images of the models were superimposed, and the positional and angular deviations of the implants were measured with metrology software. An analysis of variance (ANOVA) test was performed to evaluate the intergroup differences. No significant differences were found for all the positional and angular deviations among the three implant sites, except the bucco-lingual deviation at the implant platform in the #47 position (0.43 ± 0.19 mm) that was significantly larger than the #46 (0.21 ± 0.14 mm) and #36 (0.24 ± 0.25 mm) positions (p < 0.0001). Within the limits of this study, we conclude that, in distal extension situation of missing mandibular molars, adding a bone-supported strut in the distal part of the surgical guide can be beneficial to the accuracy of the sGIS.

Effects of bioactive glass coating by electrophoretic deposition on esthetical, bending, and frictional performance of orthodontic stainless steel wire.

We investigated the surface modification of orthodontic stainless steel wire using electrophoretic deposition (EPD) of bioactive glass (BG). BG coatings were characterized by spectrophotometry, three-dimensional (3D) focal laser scanning microscopy and scanning electron microscopy. The mechanical properties of the BG-coated wires were estimated nanoindentation, three-point bending and drawing friction tests. BG-coated specimens prepared at higher voltage showed higher values for both reflectance and L* compared to those prepared at lower voltage. Specimens coated at higher voltage had significantly lower surface roughness than those coated at lower voltage, and their BG layers had higher hardness and elastic modulus values. In the three-point bending test, BG-coated wires produced significantly lower elastic modulus than non-coated wires. Most BG-coated specimens produced similar frictional forces to those produced by non-coated specimens. The surface modification technique applying EPD and BG coating to orthodontic stainless steel wire could be used to develop new esthetical orthodontic wire.

Effects of chemical treatment as an adjunctive of air-abrasive debridement on restoring the surface chemical properties and cytocompatibility of experimentally contaminated titanium surfaces.

The aim of this study was to evaluate the effects of three different chemotherapeutic agents, following air-abrasive debridement, on surface chemical properties and cytocompatibility. Disks contaminated with Streptococcus gordonii biofilm were treated with air-abrasion and immersion in either 0.9% NaCl (Air + NaCl), 0.05% alkaline electrolyzed water (AEW) (Air + AEW), or 3% H2 O2 (Air + H2 O2 ). Noncontaminated and untreated titanium disks served as a control (As-polished). The efficacy of biofilm removal, magnitude of initial cytocompatibility toward human bone marrow mesenchymal stem cells, and surface chemical properties were determined. In all treatment groups, biofilms containing microorganisms were observed to be completely removed. The data showed discrepancies for cell affinities among treatment groups, whereby: (1) the number of cells attached to the Air + AEW treated surfaces was approximately two times greater than that to the Air + NaCl treated surfaces; and (2) cell spreading was significantly enhanced on the Air + AEW treated surfaces compared with the Air + NaCl or Air + H2 O2 treated surfaces. X-ray photoelectron spectroscopy data showed that the mean relative concentrations of nitrogen to titanium on the As-polished, Air + NaCl, Air + AEW, and Air + H2 O2 surfaces were 0.0079, 0.0237, 0.0071, and 0.0210, respectively, which would provide a clear understanding that these discrepancies could be attributed to sufficient removals of organic-nitrogen deposits at the same magnitude as the As-polished following the Air + AEW treatment. This study clarifies that chemical surface treatment with AEW, as an adjunctive to air-abrasive debridement may be beneficial in restoring surface properties for tissue integration. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 108B:183-191, 2020.

Chemical modification of pure titanium surfaces to enhance the cytocompatibility and differentiation of human mesenchymal stem cells.

The aim of this study was to improve the cytocompatibility and differentiation of human bone marrow-derived mesenchymal stem cells on the surface of titanium implants by immobilizing biofunctional molecules on their surface. Gly-Arg-Gly-Asp-Ser (GRGDS) peptides, human plasma fibronectin (pFN), or type I collagen from calf skin (Col) was covalently immobilized on the titanium surfaces. Twice as many cells attached to the Col- and pFN-immobilized titanium surfaces than attached to the as-polished surface control. The ALP activity of the cells, as well as the mineralized nodule formation, was significantly higher on the Col- and pFN-immobilized titanium surfaces than on the as-polished surfaces. These results indicate that the immobilization of biofunctional molecules such as Col and pFN on titanium surfaces enhances the attachment, spreading, proliferation, and differentiation of human bone marrow-derived mesenchymal stem cells, which may lead to a more rapid bone-titanium integration.

Inhibition of enamel demineralization by an ion-releasing tooth-coating material.

PURPOSE: To evaluate the inhibitory effect of a surface pre-reacted glass-ionomer (S-PRG) filler-containing tooth-coating material on enamel demineralization. The outer surface of the S-PRG filler is in a state in which ions are readily released. METHODS: Human enamel blocks were incubated in lactic acid solution (pH 4.0) with and without a disk (n=6) made of the cured tooth-coating material. Test solutions were changed every 24 hours and incubation was continued for 4 days. The pH and amount of fluoride released were measured with an electrode and ion meter, respectively. The concentrations of ions (aluminum, boron, calcium, phosphorus, silicon, sodium, and strontium) were measured by inductively coupled plasma atomic emission spectroscopy. The surface of the enamel block was observed with a scanning electron microscope. RESULTS: Enamel demineralization was not observed in an enamel block incubated with a disk of the tooth-coating material. Ions released from S-PRG filler had an acid buffering action in the low pH lactic acid solution. However, in the enamel block-only solution showing high levels of calcium ion release, the degree of demineralization was correlated with morphological changes of the enamel surface. CLINICAL SIGNIFICANCE: Due to the buffering effects of the pre-reacted glass-ionomer surface by ion release, the S-PRG filler-containing tooth-coating material inhibited enamel demineralization by neutralizing the acidic environment at an early time point.

A 0.8-cm clear cell neuroendocrine tumor G1 of the gallbladder with lymph node metastasis: a case report.

BACKGROUND: Neuroendocrine tumors (NETs) of the gallbladder are rare and generally considered low-grade malignancies. We herein describe a case of a patient with a 0.8-cm clear cell NET G1 of the gallbladder with nodal involvement. CASE PRESENTATION: A 65-year-old man with no medical history indicative of von Hippel-Lindau (VHL) disease underwent laparoscopic cholecystectomy for cholecystolithiasis. There was a 0.8-cm tumor in the neck of the gallbladder. Histologic examination revealed nests or trabecular growth of clear cells with small round-to-oval nuclei. Immunohistochemically, tumor cells showed positivity for chromogranin A and synaptophysin; Ki-67 index was < 1.0%. Based on the World Health Organization 2010 classification, we made a diagnosis of clear cell variant of NET G1 without VHL disease. The tumor invaded the muscular layer and had no extension to the perimuscular connective tissue but had metastasized to a cystic duct node. A radical second resection with regional lymphadenectomy of the gallbladder was performed, and there was no metastasis on histology. After the definitive surgery, he was followed up for 10 months without adjuvant therapy and is alive and well with no evidence of recurrence. CONCLUSIONS: Our experience suggests that, even when smaller than 1 cm, NET G1 of the gallbladder can metastasize. When NET G1 is incidentally identified in the gallbladder of a surgical specimen, detailed pathologic examination of the cystic duct node, when found, should be performed to guide whether a radical second resection with regional lymphadenectomy is appropriate.

Designing an antibacterial acrylic resin using the cosolvent method -Effect of ethanol on the optical and mechanical properties of a cold-cure acrylic resin.

Antimicrobial cetylpyridinium chloride (CPC) has low miscibility with acrylic resin monomer but can be homogeneously mixed using ethanol as a cosolvent. This study investigated the effects of ethanol addition on the properties of a cold-cure acrylic resin. Ethanol was an excellent cosolvent for CPC and methyl methacrylate monomer (MMA), but the cured resin exhibited a strong change in coloration to yellow (ΔE*ab>8) and a drastically reduced bending strength (from 97 to 25 MPa) and elastic modulus (from 2.7 to 0.6 GPa) when equal volumes of ethanol and monomer were used together, possibly due to the solvation and deactivation of radicals by ethanol. However, these unfavorable effects diminished when the ethanol/MMA ratio was reduced to 0.25, and became smaller when each specimen was depressurized and excess ethanol was removed. Thus, it may be possible to develop a molecularly uniform antibacterial acrylic resin with acceptable color and strength using this simple technique.

Effects of chitosan fiber addition on the properties of polyurethane with thermo-responsive shape memory.

We investigated the effects of the addition of chitosan fiber (biomass nanofiber made by Sugino (BiNFi-s)) to polyether-based thermoplastic polyurethane (TPU) on material properties. BiNFi-s (2 and 5 wt %)/TPU composite materials were prepared via compression molding, and glass fiber (2 and 5 wt %)/TPU composite materials and plain TPU were also prepared for comparison. The glass transition temperature was analyzed using differential scanning calorimetry, and the crystal structure was investigated using X-ray diffraction. 20-mm-long test specimens with cross-sectional dimensions of 1 mm × 1 mm were cut from sheets of the composite materials, and three-point bending tests were carried out using a universal testing machine to investigate their mechanical properties and shape memory. The addition of BiNFi-s or glass fiber to TPU did not influence the glass transition temperature, although the crystal structure changed from semi-crystalline to amorphous. The elastic modulus increased 40% by the addition of 5 wt % BiNFi-s (2.31 MPa) compared with plain TPU (1.65 MPa), and these composites exhibited shape recovery with clinically relevant changes in temperature. The addition of 5 wt % BiNFi-s into TPU resulted in an improvement in the elastic modulus without any decrease in the shape memory effect. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1151-1156, 2017.

[A Case of Locally Advanced Neuroendocrine Carcinoma of the Stomach Could be Curably Resected after Chemotherapy with CPT-11/CDDP].

A 64-year-old man was admitted to our hospital because of epigastralgia. Gastrointestinal endoscopyrevealed a submucosal tumor with ulceration in the upper bodyof the stomach. The tumor was histologicallydiagnosed as a neuroendocrine carcinoma. CT showed that the tumor had directlyinfiltrated the pancreas and splenic vessels. The patient underwent onlyan exploratorylaparotomybecause the tumor seemed to involve the celiac artery. Chemotherapywas conducted using CPT-11/ CDDP. After 15 courses of chemotherapy, a significant tumor reduction was obtained. We performed total gastrectomy with D2 lymphadenectomy, distal pancreatectomy and splenectomy. Histopathological examination of surgical specimens showed that onlyfew carcinoma cells remained in the stomach and pancreas. Neoadjuvant chemotherapycan be a useful treatment for unresectable locallyadvanced neuroendocrine carcinoma of the stomach.

[Two Episodes of Colostomy-Associated Intestinal Perforation during Chemotherapy for Metastatic Rectal Cancer].

A 77-year-old woman with rectal cancer and synchronous liver metastasis underwent a Hartmann operation with D3 lymph node dissection in June 2014. mFOLFOX6 plus bevacizumab(bev)was then administered to treat the liver metastasis.In February 2015, multiple liver metastases were detected and the regimen was changed to FOLFIRI plus bev.After 3 courses, peritonitis due to intestinal perforation around the descending colostomy occurred, and an emergency operation(partial resection of the descending colon and transverse colostomy)was performed.FOLFIRI was then administered from 2 months after the operation.After 3 courses of this regimen, a CT scan showed progression of the hepatic metastases.The regimen was therefore changed to mFOLFOX6.Five months later, another CT scan showed an intestinal perforation of the transverse colostomy at the abdominal wall, and an emergency cecostomy was performed.At this stage, chemotherapy was ceased.This case highlights the risk of intestinal perforation during chemotherapy, regardless of the use of bev.

[Surgical Resection after Gemcitabine plus Cisplatin Chemotherapy for Intrahepatic Cholangiocarcinoma with Multiple Lymph Node Metastases - Report of a Case].

An 82-year-old man with upper abdominal pain was referred to our hospital because of an elevated serum CEA level and dilatation of the intrahepatic bile ducts on ultrasonography.Computed tomography revealed a hypovascular mass measuring 5.0 cm in size in the lateral section, dilatation of the peripheral intrahepatic bile ducts, and swollen lymph nodes around the lesser curvature of the stomach, the common hepatic artery, and the paraaorta.He was diagnosed with unresectable intrahepatic cholangiocarcinoma, and he received chemotherapy with biweekly gemcitabine plus cisplatin.After 33 courses of the chemotherapy, computed tomography revealed that the tumor size decreased over 63%, and all swollen lymph nodes had almost resolved.He underwent a left hemihepatectomy 1 year 6 months after the start of the chemotherapy.He remains alive and well with no evidence of recurrence, 11 months after resection.

NaOCl-mediated biofunctionalization enhances bone-titanium integration.

The aim of this study was to examine the effect of NaOCl pretreatment on the biomechanical fixation of implant at the early healing stage of a rat model. Polished titanium cylindrical implants and disks were prepared, and one-half of these samples were dual acidetched. Then, one-half of both surfaces were chemically-cleaned by pretreatment with 5% NaOCl solution for 24 h. Morphological analyses showed that there was no significant difference between before and after NaOCl treatment. The wettability measurement demonstrated that NaOCl treatment secondarily converted both titanium surfaces from hydrophobic to superhydrophilic, accompanied by the removal of hydrocarbons from the titanium surfaces. Biomechanical push-in test indicated that the bone-titanium integration strength of the NaOCl-treated implants were significantly greater than that of the untreated implants (p<0.05). These results showed that NaOCl pretreatment enhanced the osseointegration capability of titanium, indicating its potential for a simple chemical chair-side pretreatment method.