The Conditions Necessary for the Formation of Dissipative Structures in Tribo-Films on Friction Surfaces That Decrease the Wear Rate.

Tribo-films form on surfaces as a result of friction and wear. The wear rate is dependent on the frictional processes, which develop within these tribo-films. Physical-chemical processes with negative entropy production enhance reduction in the wear rate. Such processes intensively develop once self-organization with dissipative structure formation is initiated. This process leads to significant wear rate reduction. Self-organization can only occur after the system loses thermodynamic stability. This article investigates the behavior of entropy production that results in the loss of thermodynamic stability in order to establish the prevalence of friction modes required for self-organization. Tribo-films with dissipative structures form on the friction surface as a consequence of a self-organization process, resulting in an overall wear rate reduction. It has been demonstrated that a tribo-system begins to lose its thermodynamic stability once it reaches the point of maximum entropy production during the running-in stage.

Validation of the EPACODI-1 Scale: University Students' Perceptions of Inclusive Education.

In the last fifteen years, changes have been taking place in education systems at the international and national levels that aim to achieve, in the near future, the objectives set by the UN International Convention on the Rights of Persons with Disabilities (hereafter CRPD). Spain is no stranger to these objectives, as recognized in the new Organic Law for the Modification of the Law on the Organization of Education. This situation makes it necessary to know the perceptions that professionals in training (about to graduate) from faculties of education have about the legal content established by articles 4.1.i and 24 of the CRPD on inclusive education. In order to ascertain these perceptions, the EPACO-DI-1 instrument was used in a quantitative and confirmatory study by means of a multivariate factor analysis (CFA), applying the parallel estimation method of ordinary least squares (OLS) and principal axes with polychoric correlation and promax oblique rotation. This study involved 552 fourth-year students between the ages of 21 and over 45 from the specializations offered by the Faculty of Education of the University of Murcia. The obtained results are consistent and show the validity of the EPACODI-1 scale for determining the perceptions of professionals in training on inclusive education.

Physical and Chemical Properties Characterization of 3D-Printed Substrates Loaded with Copper-Nickel Nanowires.

This study deals with the laser stereolithography manufacturing feasibility of copper-nickel nanowire-loaded photosensitive resins. The addition of nanowires resulted in a novel resin suitable for additive manufacturing technologies based on layer-by-layer photopolymerization. The pure and nanowire-loaded resin samples were 3D printed in a similar way. Their morphological, mechanical, thermal, and chemical properties were characterized. X-ray computed tomography revealed that 0.06 vol % of the composite resin was filled with nanowires forming randomly distributed aggregates. The increase of 57% in the storage modulus and 50% in the hardness when loading the resin with nanowire was attributed to the load transfer. Moreover, the decrease in the glass transition temperature from 57.9 °C to 52.8 °C in the polymeric matrix with nanowires evidenced a decrease in the cross-linking density, leading to a higher mobility of the polymer chains during glass transition. Consequently, this research demonstrates the successful dispersion and use of copper-nickel nanowires as a reinforcement material in a commercial resin for laser stereolithography.

Functional evaluation and testing of a newly developed Teleost's Fish Otolith derived biocomposite coating for healthcare.

Polymers such as polycaprolactone (PCL) possess biodegradability, biocompatibility and affinity with other organic media that makes them suitable for biomedical applications. In this work, a novel biocomposite coating was synthesised by mixing PCL with layers of calcium phosphate (hydroxyapatite, brushite and monetite) from a biomineral called otolith extracted from Teleost fish (Plagioscion Squamosissimus) and multiwalled carbon nanotubes in different concentrations (0.5, 1.0 and 1.5 g/L). The biocomposite coating was deposited on an osteosynthesis material Ti6Al4V by spin coating and various tests such as Fourier transformation infrared spectroscopy (FTIR), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), scratch tests, MTT reduction cytotoxicity, HOS cell bioactivity (human osteosarcoma) by alkaline phosphatase (ALP) and fluorescence microscopy were performed to comprehensively evaluate the newly developed biocoating. It was found that an increase in the concentration of carbon nanotube induced microstructural phase changes of calcium phosphate (CP) leading to the formation of brushite, monetite and hydroxyapatite. While we discovered that an increase in the concentration of carbon nanotube generally improves the adhesion of the coating with the substrate, a certain threshold exists such that the best deposition surfaces were obtained as PCL/CP/CNT 0.0 g/L and PCL/CP/CNT 0.5 g/L.

Benchmarking of several material constitutive models for tribology, wear, and other mechanical deformation simulations of Ti6Al4V.

Use of an alpha-beta (multiphase HCP-BCC) titanium alloy, Ti6Al4V, is ubiquitous in a wide range of engineering applications. The previous decade of finite element analysis research on various titanium alloys for numerous biomedical applications especially in the field of orthopedics has led to the development of more than half a dozen material constitutive models, with no comparison available between them. Part of this problem stems from the complexity of developing a vectorised user-defined material subroutine (VUMAT) and the different conditions (strain rate, temperature and composition of material) in which these models are experimentally informed. This paper examines the extant literature to review these models and provides quantitative benchmarking against the tabulated material model and a power law model of Ti6Al4V taking the test case of a uniaxial tensile and cutting simulation.

Manufacturing of Polymeric Substrates with Copper Nanofillers through Laser Stereolithography Technique.

This study presents the additive manufacture of objects using mass-functionalized photo-resins, which are additively photopolymerized using the laser stereolithography technique. The mass functionalization is based on the incorporation of copper nanowires used as fillers at different concentrations. Cylindrical and tensile test probes are designed and manufactured in a layer-by-layer approach using a low-cost laser stereolithography system working with a layer thickness of 100   µ m . The morphological, mechanical, thermal and chemical results help to show the viability and potential that this combination of mass-functionalized resins and technological processes may have in the near future, once key challenges are solved. Finally, some potential applications are also discussed.

UV Treatment of Flexible Copper Nanowire Mesh Films for Transparent Conductor Applications.

Copper nanowires have the potential to reach and even exceed the indium tin oxide performances as flexible transparent conductive electrodes. However, for a large-scale production, they need to be fabricated in a high-speed, low-cost way, without degrading the flexible substrate. One of the major bottlenecks resides in the post-treatment used to remove organic residues from the surface of the nanowires after forming the transparent electrode, which is necessary to obtain high optoelectronic performances. Here, we propose an ultra-violet irradiation and a subsequent acetic acid bath as an easy, scalable, fast post-treatment. After only 2 min of ultra-violet treatment, followed by 10 min of acid bath, an Rs of 42 Ω sq-1 and a T 550 nm of 87% were measured. Besides, copper nanowire electrodes maintained their high transparency in the range 750-2500 nm, which makes them good candidates for applications such as infrared solar cells.

Effect of silver on the phase transition and wettability of titanium oxide films.

The effect of silver on the phase transition and microstructure of titanium oxide films grown by pulsed cathodic arc had been investigated by XRD, SEM and Raman spectroscopy. Following successive thermal annealing up to 1000 °C, microstructural analysis of annealed Ag-TiO2 films reveals that the incorporation of Ag nanoparticles strongly affects the transition temperature from the initial metastable amorphous phase to anatase and stable rutile phase. An increase of silver content into TiO2 matrix inhibits the amorphous to anatase phase transition, raising its temperature boundary and, simultaneously reduces the transition temperature to promote rutile structure at lower value of 600 °C. The results are interpreted in terms of the steric effects produced by agglomeration of Ag atoms into larger clusters following annealing which hinders diffusion of Ti and O ions for anatase formation and constrains the volume available for the anatase lattice, thus disrupting its structure to form rutile phase. The effect of silver on the optical and wetting properties of TiO2 was evaluated to demonstrate its improved photocatalytic performance.

Local modification of the microstructure and electrical properties of multifunctional Au-YSZ nanocomposite thin films by laser interference patterning.

Nanocomposite films consisting of gold nanoparticles embedded in an yttria-stabilized zirconia matrix (Au-YSZ) have been synthesized with different gold loadings by reactive magnetron sputtering followed by ex situ annealing in air or laser interference patterning (LIP) treatment. It is shown that the electrical conductivity of the nanocomposite films can be modified to a large extent by changing the gold loading, by thermal annealing, or by LIP. The structural and microstructural analyses evidenced the segregation of metallic gold in crystalline form for all synthesis conditions and treatments applied. Thermal annealing above 400 °C is observed to trigger the growth of pre-existing nanoparticles in the volume of the films. Moreover, pronounced segregation of gold to the film surface is observed for Au/(Au + Zr + Y) ratios above 0.40, which may prevent the use of thermal annealing to functionalize gold-rich Au-YSZ coatings. In contrast, significant modifications of the microstructure were detected within the interference spot (spot size close to 2 × 2 mm) of LIP treatments only for the regions corresponding to constructive interference. As a consequence, besides its already demonstrated ability to modify the friction behavior of Au-YSZ films, the LIP treatment enables local tailoring of their electrical resistivity. The combination of these characteristics can be of great interest for sliding electrical contacts.

Why can tiAicrsiYN-based adaptive coatings deliver exceptional performance under extreme frictional conditions?

Adaptive TiAlCrSiYN-based coatings show promise under the extreme tribological conditions of dry ultra-high-speed (500-700 m min-1) machining of hardened tool steels. During high speed machining, protective sapphire and mullite-like tribo-films form on the surface of TiAlCrSiYN-based coatings resulting in beneficial heat-redistribution in the cutting zone. XRD and HRTEM data show that the tribo-films act as a thermal barrier creating a strong thermal gradient. The data are consistent with the temperature decreasing from approximately 1100-1200 degrees C at the outer surface to approximately 600 degrees C at the tribo-film/coating interface. The mechanical properties of the multilayer TiAICrSiYN/TiA1CrN coating were measured by high temperature nanoindentation. It retains relatively high hardness (21 GPa) at 600 degrees C. The nanomechanical properties of the underlying coating layer provide a stable low wear environment for the tribo-films to form and regenerate so it can sustain high temperatures under operation (600 degrees C). This combination of characteristics explains the high wear resistance of the multilayer TiAlCrSiYN/TiAICrN coating under extreme operating conditions. TiAlCrSiYN and TiAlCrN monolayer coatings have a less effective combination of adaptability and mechanical characteristics and therefore lower tool life. The microstructural reasons for different optimum hardness and plasticity between monolayer and multilayer coatings are discussed.

Hierarchical adaptive nanostructured PVD coatings for extreme tribological applications: the quest for nonequilibrium states and emergent behavior.

Adaptive wear-resistant coatings produced by physical vapor deposition (PVD) are a relatively new generation of coatings which are attracting attention in the development of nanostructured materials for extreme tribological applications. An excellent example of such extreme operating conditions is high performance machining of hard-to-cut materials. The adaptive characteristics of such coatings develop fully during interaction with the severe environment. Modern adaptive coatings could be regarded as hierarchical surface-engineered nanostructural materials. They exhibit dynamic hierarchy on two major structural scales: (a) nanoscale surface layers of protective tribofilms generated during friction and (b) an underlying nano/microscaled layer. The tribofilms are responsible for some critical nanoscale effects that strongly impact the wear resistance of adaptive coatings. A new direction in nanomaterial research is discussed: compositional and microstructural optimization of the dynamically regenerating nanoscaled tribofilms on the surface of the adaptive coatings during friction. In this review we demonstrate the correlation between the microstructure, physical, chemical and micromechanical properties of hard coatings in their dynamic interaction (adaptation) with environment and the involvement of complex natural processes associated with self-organization during friction. Major physical, chemical and mechanical characteristics of the adaptive coating, which play a significant role in its operating properties, such as enhanced mass transfer, and the ability of the layer to provide dissipation and accumulation of frictional energy during operation are presented as well. Strategies for adaptive nanostructural coating design that enhance beneficial natural processes are outlined. The coatings exhibit emergent behavior during operation when their improved features work as a whole. In this way, as higher-ordered systems, they achieve multifunctionality and high wear resistance under extreme tribological conditions.