Longitudinal CT-based finite element analyses provide objective fracture healing measures in an ovine tibia model.

Measuring the healing status of a bone fracture is important to determine the clinical care a patient receives. Implantable devices can directly and continuously assess the healing status of fracture fixation constructs, while subject-specific virtual biomechanical tests can noninvasively determine callus structural integrity at single time points. Despite their potential for objectification, both methods are not yet integrated into clinical practice with further evidence of their benefits required. This study correlated continuous data from an implantable sensor assessing healing status through implant load monitoring with computer tomography (CT) based longitudinal finite element (FE) simulations in a large animal model. Eight sheep were part of a previous preclinical study utilizing a tibial osteotomy model and equipped with such a sensor. Sensor signal was collected over several months, and CT scans were acquired at six interim time points. For each scan, two FE analyses were performed: a virtual torsional rigidity test of the bone and a model of the bone-implant construct with the sensor. The longitudinal simulation results were compared to the sensor data at corresponding time points and a cohort-specific empirical healing rule was employed. Healing status predicted by both in silico simulations correlated significantly with the sensor data at corresponding time points and correctly identified a delayed and a nonunion in the cohort. The methodology is readily translatable with the potential to be applied to further preclinical or clinical cohorts to find generalizable healing criteria. Virtual mechanical tests can objectively measure fracture healing progressing using longitudinal CT scans.

Experimental and virtual testing of bone-implant systems equipped with the AO Fracture Monitor with regard to interfragmentary movement.

Introduction: The management of fractured bones is a key domain within orthopedic trauma surgery, with the prevention of delayed healing and non-unions forming a core challenge. This study evaluates the efficacy of the AO Fracture Monitor in conjunction with biomechanical simulations to better understand the local mechanics of fracture gaps, which is crucial for comprehending mechanotransduction, a key factor in bone healing. Through a series of experiments and corresponding simulations, the study tests four hypotheses to determine the relationship between physical measurements and the predictive power of biomechanical models. Methods: Employing the AO Fracture Monitor and Digital Image Correlation techniques, the study demonstrates a significant correlation between the surface strain of implants and interfragmentary movements. This provides a foundation for utilizing one-dimensional AO Fracture Monitor measurements to predict three-dimensional fracture behavior, thereby linking mechanical loading with fracture gap dynamics. Moreover, the research establishes that finite element simulations of bone-implant systems can be effectively validated using experimental data, underpinning the accuracy of simulations in replicating physical behaviors. Results and Discussion: The findings endorse the combined use of monitoring technologies and simulations to infer the local mechanical conditions at the fracture site, offering a potential leap in personalized therapy for bone healing. Clinically, this approach can enhance treatment outcomes by refining the assessment precision in trauma trials, fostering the early detection of healing disturbances, and guiding improvements in future implant design. Ultimately, this study paves the way for more sophisticated patient monitoring and tailored interventions, promising to elevate the standard of care in orthopedic trauma surgery.

Decreasing implant load indicates spinal fusion when measured continuously.

Reliable and timely assessment of bone union between vertebrae is considered a key challenge after spinal fusion surgery. Recently, a novel sensor concept demonstrated the ability to objectively assess posterolateral fusion based on continuous implant load monitoring. The aim of this study was to investigate systematically the concept in a mono-segmental fusion model using an updated sensor setup. Three sheep underwent bilateral facetectomy at level L2-L3 and L4-L5. The segments were stabilized using two unconnected pedicle-screw-rod constructs per level. Sensing devices were attached to the rods between each pedicle screw pair and the loads were continuously monitored over 16 weeks. After euthanasia, the spines were biomechanically tested for their range of motion and high-resolution CT scans were performed to confirm the fusion success. After an initial increase in implant load until reaching a maximum (100 %) at approximately week 4, eleven out of twelve sensors measured a constant decrease in implant load to 52 ± 9 % at euthanasia. One sensor measurement was compromised by newly forming bone growing against the sensor clamp. Bridging bone at each facet and minor remnant segmental motion (<0.7°) confirmed the fusion of all motion segments. Data obtained by continuous measurement of implant loading of spinal screw-rod constructs enables objective monitoring of spinal fusion progression. The sensor concept provides valuable real-time information, offering quantifiable data as an alternative to traditional imaging techniques. However, the design of the current sensor concept needs to be matured, tailored to, and validated for the human spine.

The absence of immediate stimulation delays bone healing.

AIM: Secondary bone healing requires an adequate level of mechanical stimulation expressed by the extent of interfragmentary motion in the fracture. However, there is no consensus about when the mechanical stimulation should be initiated to ensure a timely healing response. Therefore, this study aims to compare the effect of the immediate and delayed application of mechanical stimulation in a large animal model. METHODS: Twelve Swiss White Alpine sheep underwent partial osteotomy of a tibia that was stabilised with an active fixator inducing well-controlled mechanical stimulation. Animals were randomly assigned into two groups with different stimulation protocols. The immediate group received daily stimulation (1000 cycles/day) from the first day post-operation, while in the delayed group, stimulation began only on the 22nd day post-operation. Healing progression was evaluated daily by measuring the in vivo stiffness of the repair tissue and by quantifying callus area on weekly radiographs. All animals were euthanised five weeks post-op. Post-mortem callus volume was determined from high-resolution computer tomography (HRCT). RESULTS: Fracture stiffness (p < 0.05) and callus area (p < 0.01) were significantly larger for the immediate group compared to the delayed stimulation group. In addition, the callus volume measured on the post-mortem HRCT showed 319 % greater callus volume for the immediate stimulation group (p < 0.01). CONCLUSIONS: This study demonstrates that a delay in the onset of mechanical stimulation retards fracture callus development and that mechanical stimulation already applied in the early post-op phase promotes bone healing.

Continuous Implant Load Monitoring to Assess Bone Healing Status-Evidence from Animal Testing.

Background and Objectives: Fracture healing is currently assessed through qualitative evaluation of radiographic images, which is highly subjective in nature. Radiographs can only provide snapshots in time, which are limited due to logistics and radiation exposure. We recently proposed assessing the bone healing status through continuous monitoring of the implant load, utilizing an implanted sensor system, the Fracture Monitor. The device telemetrically transmits statistically derived implant parameters via the patient's mobile phone to assist physicians in diagnostics and treatment decision-making. This preclinical study aims to systematically investigate the device safety and performance in an animal setting. Materials and Methods: Mid-shaft tibial osteotomies of different sizes (0.6-30 mm) were created in eleven Swiss mountain sheep. The bones were stabilized with either a conventional Titanium or stainless-steel locking plate equipped with a Fracture Monitor. Data were continuously collected over the device's lifetime. Conventional radiographs and clinical CT scans were taken longitudinally over the study period. The radiographs were systematically scored and CTs were evaluated for normalized bone volume in the defect. The animals were euthanized after 9 months. The sensor output was correlated with the radiologic parameters. Tissue samples from the device location were histologically examined. Results: The sensors functioned autonomously for 6.5-8.4 months until energy depletion. No macroscopic or microscopic adverse effects from device implantation were observed. The relative implant loads at 4 and 8 weeks post-operation correlated significantly with the radiographic scores and with the normalized bone volume metric. Conclusions: Continuous implant load monitoring appears as a relevant approach to support and objectify fracture healing assessments and carries a strong potential to enable patient-tailored rehabilitation in the future.

Continuous Rod Load Monitoring to Assess Spinal Fusion Status-Pilot In Vivo Data in Sheep.

Background and Objectives: Spinal fusion is an effective and widely accepted intervention. However, complications such as non-unions and hardware failures are frequently observed. Radiologic imaging and physical examination are still the gold standards in the assessment of spinal fusion, despite multiple limitations including radiation exposure and subjective image interpretation. Furthermore, current diagnostic methods only allow fusion assessment at certain time points and require the patient's presence at the hospital or medical practice. A recently introduced implantable sensor system for continuous and wireless implant load monitoring in trauma applications carries the potential to overcome these drawbacks, but transferability of the principle to the spine has not been demonstrated yet. Materials and Methods: The existing trauma sensor was modified for attachment to a standard pedicle-screw-rod system. Two lumbar segments (L2 to L4) of one Swiss white alpine sheep were asymmetrically instrumented. After facetectomy, three sensors were attached to the rods between each screw pair and activated for measurement. The sheep was euthanized 16 weeks postoperatively. After radiological assessment the spine was explanted and loaded in flexion-extension to determine the range of motion of the spinal segments. Sensor data were compared with mechanical test results and radiologic findings. Results: The sensors measured physiological rod loading autonomously over the observation period and delivered the data daily to bonded smartphones. At euthanasia the relative rod load dropped to 67% of the respective maximum value for the L23 segment and to 30% for the L34 segment. In agreement, the total range of motion of both operated segments was lower compared to an intact reference segment (L23: 0.57°; L34: 0.49°; intact L45: 4.17°). Radiologic assessment revealed fusion mass in the facet joint gaps and bilateral bridging bone around the joints at both operated segments. Conclusions: Observations of this single-case study confirm the basic ability of continuous rod load measurement to resolve the spinal fusion process as indicated by a declining rod load with progressing bone fusion. A strong clinical potential of such technology is eminent, but further data must be collected for final proof of principle.

Short-Term Bone Healing Response to Mechanical Stimulation-A Case Series Conducted on Sheep.

It is well known that mechanical stimulation promotes indirect fracture healing by triggering callus formation. We investigated the short-term response of healing tissue to mechanical stimulation to compare the changes in tissue stiffness during stimulation and resting phases in a preclinical case-series. Four sheep underwent a tibial osteotomy and were instrumented with a custom-made active fixator which applied a mechanical stimulation protocol of 1000 cycles/day, equally distributed over 12 h, followed by 12 h of rest. During each cycle, a surrogate metric for tissue stiffness was measured, enabling a continuous real-time monitoring of the healing progression. A daily stiffness increase during stimulation and an increase during resting were evaluated for each animal. One animal had to be excluded from the evaluation due to technical reasons. For all included animals, the stiffness began to increase within the second week post-op. A characteristic pattern was observed during daily measurements: the stiffness dropped considerably within the first stimulation cycles followed by a steady rise throughout the rest of the stimulation phase. However, for all included animals, the average daily stiffness increase within the first three weeks post operation was larger during resting than during stimulation (Sheep I: 16.9% vs. -5.7%; Sheep II: 14.7% vs. -1.8%; Sheep III: 8.9% vs. 1.6%). A continuous measurement of tissue stiffness together with a controlled fracture stimulation enabled the investigation of the short-term effects of specific stimulatory parameters, such as resting periods. Resting was identified as a potentially determining factor for bone healing progression. Optimizing the ratio between stimulation and resting may contribute to more robust fracture healing in the future.

Clinical feasibility of fracture healing assessment through continuous monitoring of implant load.

Current fracture fixation follow-up is based on subjective radiological and clinical examination. Efforts to objectify the procedure have been undertaken since decades. Assessment of implant load as an indirect predictor of callus maturity has so far failed to enter clinical routine due to limited practicability, technical obstacles and its snap-shot nature. We recently introduced the concept of continuous implant load monitoring to aid in diagnosing fracture healing progression. This study aimed at investigating the feasibility of the system in a clinical context. Ten patients treated with Taylor-Spatial-Frame external fixators following pathological tibia fractures were equipped with a Fracture Monitor device attached to a fixator-strut and were monitored until hardware removal. Two patients were excluded due to technical issues. Implant load and fracture activity was continuously and autonomously measured for 139 ± 89 days (mean ± SD). Data was wirelessly collected with consumer smartphones. Relative implant load initially rose for 34.1 ± 22.2 days and finally declined to a level of 45.0 ± 33.8% of the maximum implant load. In five patients the load dropped below 50% of the maximum load. These patients underwent hardware removal according to the clinical assessment. In three patients, whose external fixators were exchanged to internal fixation at the end of the study, implant load did not drop below the 50% margin. The continuous measurement principle allows resolving implant load progression and appears indicative for the bone healing status. Data can be acquired in a homecare setting and is believed to provide valuable information to support timely healing assessment and enable patient specific after-care.

Smart implants in fracture care - only buzzword or real opportunity?

The assessment of fracture healing is still marked by a subjective and diffuse outcome due to the lack of clinically available quantitative measures. Without reliable information on the progression of healing and uniform criteria for union and non-union, therapeutic decision making, e.g. regarding the allowed weight bearing, hinges on the experience and the subjective evaluation of physicians. Already decades ago, fracture stiffness has been identified as a valid outcome measure for the maturity of the repair tissue. Despite early promising results, so far no method has made its way into practice beyond clinical studies. However, with current technological advancements and a general trend towards digital health care, measuring fracture healing seems to regain momentum. New generations of instrumented implants with sensoring capabilities, often termed as "smart implants", are under development. They target X-ray free and timely provision of reliable feedback upon the mechanical competence of the repair tissue and the healing environment to support therapeutic decision making and individualized after-care. With the gained experience from these devices, the next generations of smart implants may become increasingly sophisticated by internally analyzing the measured data and suggesting adequate therapeutic actions on their own.

Morphology of bony callus growth in healing of a sheep tibial osteotomy.

Long bone fractures typically heal via formation of an external callus, which helps stabilise the bone fragments. Callus composition and morphology influence the mechanical environment, which in turn regulates the progression of healing. Therefore characterising callus development over time is crucial in understanding this mechanobiological regulation. Although bony callus is often assumed to grow towards the fracture from either side, this is not consistent with observations from large animal studies and clinical cases. Therefore, we sought to quantify the morphology of bony callus over time in a large animal model. Sheep tibiae were x-rayed weekly over eight weeks following an osteotomy (n=5), with fixation allowing up to 10% axial displacement under normal weight-bearing. After scaling radiographs by known landmarks and normalising greyscales, bony callus boundaries were defined by manual segmentation. The lateral callus area and coordinates of its centroid were calculated from each image. The external callus initially formed adjacent to the osteotomy site. Over the first four weeks, callus growth from its outer surfaces was characterised by its centre of area moving outwards and away from the osteotomy, on both proximal and distal fragments. Subsequent weeks showed consolidation and resorption from the outer surface of the callus. Our approach allowed bony callus development to be tracked in individuals throughout healing. Contrary to the view that periosteal bone formation originates distant from the fracture, our data showed bony callus adjacent to the defect from early stages, followed by approximately concentric growth. This discrepancy highlights the need for data specific to experimental conditions, and particularly early stages of healing, for evaluating theoretical models of mechanical regulation.

The relation between fracture activity and bone healing with special reference to the early healing phase - A preclinical study.

BACKGROUND: Fracture healing outcome is to a great extent steered by the mechanical environment. The importance of early phase mechanical fracture stimulation is still controversially discussed, both clinically and scientifically. Furthermore, the role of fracture activity, defined as the number of stimulatory events per time, is particularly for the direct postoperative phase unknown. METHODS: Tibial defects of seven Swiss mountain sheep were stabilized with a dynamizable bone fixator, which allowed for defined interfragmentary motion by limiting the maximum axial displacement. The fixator was further equipped with a telemetric measuring unit to continuously log all occurring displacement events above a predefined amplitude threshold over an 8-weeks observation period. Callus size was measured over time from X-rays. Ultimate torsional strength of the healed defects was assessed after euthanasia. RESULTS: One animal had to be excluded from the experiment due to technical reasons. The remaining six animals exhibited consistently the highest fracture activity in week 1 post-operation with 6'029 displacement events per week for the animal with the lowest activity and 21'866 events per week for the most active animal. Afterwards fracture activity gradually decreased over time. Strong and significant correlations were found for fracture activity in week 1 and 2 with torsional strength of the healed bone (R ≥ 0.881, p ≤ 0.02). No significant correlations were observed at later timepoints. Fracture activity in week 1 and 2 also correlated strongly with the maximum callus area as measured from X-rays (R ≥ 0.846, p ≤ 0.034). CONCLUSIONS: The data demonstrates a positive effect of, within limits, frequent fracture stimulation on bone healing and suggests the importance of the mechanical environment in the direct post-operative healing phase. Clinically, the findings may advocate for the concept of direct post-operative weight bearing. This, however, requires clinical validation and must be considered within the full clinical context including the risk for fixation failure from overloading.

Programable Active Fixator System for Systematic In Vivo Investigation of Bone Healing Processes.

This manuscript introduces a programable active bone fixator system that enables systematic investigation of bone healing processes in a sheep animal model. In contrast to previous systems, this solution combines the ability to precisely control the mechanical conditions acting within a fracture with continuous monitoring of the healing progression and autonomous operation of the system throughout the experiment. The active fixator system was implemented on a double osteotomy model that shields the experimental fracture from the influence of the animal's functional loading. A force sensor was integrated into the fixator to continuously measure stiffness of the repair tissue as an indicator for healing progression. A dedicated control unit was developed that allows programing of different loading protocols which are later executed autonomously by the active fixator. To verify the feasibility of the system, it was implanted in two sheep with different loading protocols, mimicking immediate and delayed weight-bearing, respectively. The implanted devices operated according to the programmed protocols and delivered seamless data over the whole course of the experiment. The in vivo trial confirmed the feasibility of the system. Hence, it can be applied in further preclinical studies to better understand the influence of mechanical conditions on fracture healing.

Axial and shear pullout forces of composite, porcine and human metatarsal and cuboid bones.

OBJECTIVES: The varying mechanical properties of human bone have influence on the study results. Pullout and shear forces of human bone were compared to different substitutes to evaluate their suitability for biomechanical studies. METHODS: After bone mineral density (BMD) determination, axial pullout tests were performed with cortical 3.5 mm nonlocking (NL) and 2.7 mm head locking (HL) screws on human, porcine and polyurethane composite bones. Porcine and human constructs were additionally loaded in shear direction. RESULTS: Apparent BMD was significantly lower in osteoporotic (159 mgHA/ccm ± 56) and nonosteoporotic (229 mgHA/ccm ± 25) human bone than that in porcine bone (325 mgHA/ccm ± 42; p < 0.01). Axial construct stiffness and ultimate pullout force of porcine bone (NL: 666N/mm ± 226, 910N ± 140; HL: 309N/mm ± 88, 744N ± 185) was significantly different from composite bone (NL: 1284N/mm ± 161; 1175N ± 116; HL: 1241N/mm ± 172, 1185N ± 225) and osteoporotic human bone (NL: 204N/mm ± 121, 185N ± 113; HL: 201N/mm ± 65; 189N ± 58) but not from nonosteoporotic human bone (NL: 620N/mm ± 205, 852N ± 281; HL: 399N/mm ± 224; 567N ± 242). Porcine bone exhibited an ultimate shear force (NL: 278N ± 99; HL: 431N ± 155) comparable to nonosteoporotic human bone (NL: 207 ± 68: HL: 374N ± 137). CONCLUSION: Screw pullout and shear forces of porcine bone are close to nonosteoporotic human bone. THE TRANSLATIONAL POTENTIAL OF THIS ARTICLE: Human bone specimens used in biomechanical studies are predominantly of osteoporotic bone quality. Conclusions on nonosteoporotic human bone behaviour are difficult. Alternatives such as porcine bone and composite bone were investigated, and it could be shown that screw pullout and screw shear forces of porcine bone are close to nonosteoporotic human bone.

Self-Healing Dynamic Hydrogel as Injectable Shock-Absorbing Artificial Nucleus Pulposus.

The intervertebral discs (IVDs) provide unique flexibility to the spine and exceptional shock absorbing properties under impact. The inner core of the IVD, the nucleus pulposus (NP) is responsible for this adaptive behavior. Herein, we evaluate an injectable, self-healing dynamic hydrogel (DH) based on gold(I)-thiolate/disulfide (Au-S/SS) exchange as NP replacement in a spine motion segment model. For the first time, we report the application of dynamic covalent hydrogels inside biological tissues. The dynamic exchange between Au-S species and disulfide bonds (SS) resulted in self-healing ability and frequency-dependent stiffness of the hydrogel, which was also confirmed in spine motion segments. Injection of preformed DH into nucleotomized IVDs restored the full biomechanical properties of intact IVDs, including the stiffening effect observed at increasing frequencies, which cannot be achieved with conventional covalent hydrogel. DH has the potential to counteract IVD degeneration associated with high frequency vibrations. Self-healing properties, confirmed by rheology studies and macroscopic observation after injection, were required to inject preformed DH, which recovered its mechanical integrity and microstructure to act as an artificial NP. On the other hand, covalent hydrogel did not show any restoration of NP properties as this conventional material suffered irreversible damages after injection, which demonstrates that the dynamic properties are crucial for this application. The persistence of DH in the IVD space following cyclic high-frequency loading, confirmed by tomography after mechanical testing, suggests that this material would have long life span as an injectable NP replacement material.

Titanium and steel fracture fixation plates with different surface topographies: Influence on infection rate in a rabbit fracture model.

INTRODUCTION: Implant-related infection is a challenging complication in musculoskeletal trauma surgery. In the present study, we examined the role of implant material and surface topography as influencing factors on the development of infection in an experimental model of plating osteosynthesis in the rabbit. METHODS: The implants included in this experimental study were composed of: standard Electropolished Stainless Steel (EPSS), standard titanium (Ti-S), roughened stainless steel (RSS) and surface polished titanium (Ti-P). Construct stability and load-to-failure of Ti-P implants was compared to that of Ti-S implants in a rabbit cadaveric model. In an in vivo study, a rabbit humeral fracture model was used. Each rabbit received one of three Staphylococcus aureus inocula, aimed at determining the infection rate at a low, medium and high dose of bacteria. Outcome measures were quantification of bacteria on the implant and in the surrounding tissues, and determination of the infectious dose 50 (ID50). RESULTS: No significant differences were observed between Ti-S and Ti-P regarding stiffness or failure load in the cadaver study. Of the 72 rabbits eventually included in the in vivo study, 50 developed an infection. The ID50 was found to be: EPSS 3.89×10(3) colony forming units (CFU); RSS 8.23×10(3) CFU; Ti-S 5.66×10(3) CFU; Ti-P 3.41×10(3) CFU. Significantly lower bacterial counts were found on the Ti-S implants samples compared with RSS implants (p<0.001) at the high inoculum. Similarly, lower bacterial counts were found in the bone samples of animals in the Ti-S group in comparison with both RSS and EPSS groups, again at the high inoculation dose (p<0.005). CONCLUSION: No significant differences were seen in susceptibility to infection when comparing titanium and steel implants with conventional or modified topographies. Ti-P implants, which have previously been shown in preclinical studies to reduce complications associated with tissue adherence, do not affect infection rate in this preclinical fracture model. Therefore, Ti-P implants are not expected to affect the infection rate, or influence implant stability in the clinical situation.

Assessment of ankle and hindfoot stability and joint pressures using a human cadaveric model of a large lateral talar process excision: a biomechanical study.

Lateral talar process fragment excision may be followed by hindfoot instability and altered biomechanics. There is controversy regarding the ideal fragment size for internal fixation versus excision and a concern that excision of a large fragment may lead to significant instability. The aim of this study was to assess the effect of a simulated large lateral talar process excision on ankle and subtalar joint stability.A custom-made seesaw rig was designed to apply inversion/eversion stress loading on 7 fresh-frozen human cadaveric lower legs and investigate them in pre-excision, 5 cm and 10 cm lateral talar process fragment excision states. Anteroposterior radiographs were taken to assess ankle and subtalar joint tilt and calculate angular change from neutral hindfoot alignment to 10-kg forced inversion/eversion. Ankle joint pressures and contact areas were measured under 30-kg axial load in neutral hindfoot alignment.In comparison to the pre-excision state, no significantly different mediolateral angular change was observed in the subtalar joint after 5 and 10 cm lateral talar process fragment excision in inversion and eversion. With respect to the ankle joint, 10-cm fragment excision produced significantly bigger inversion tibiotalar tilt compared with the pre-excision state, P = .04. No significant change of the ankle joint pressure and contact area was detected after 5 and 10-cm excision in comparison with the pre-excison state.An excision of up to 10 cm of the lateral talar process does not cause a significant instability at the level of the subtalar joint but might be a destabilizing factor at the ankle joint under inversion stress. The latter could be related to extensive soft tissue dissection required for resection.

Microstructural parameters of bone evaluated using HR-pQCT correlate with the DXA-derived cortical index and the trabecular bone score in a cohort of randomly selected premenopausal women.

BACKGROUND: Areal bone mineral density is predictive for fracture risk. Microstructural bone parameters evaluated at the appendicular skeleton by high-resolution peripheral quantitative computed tomography (HR-pQCT) display differences between healthy patients and fracture patients. With the simple geometry of the cortex at the distal tibial diaphysis, a cortical index of the tibia combining material and mechanical properties correlated highly with bone strength ex vivo. The trabecular bone score derived from the scan of the lumbar spine by dual-energy X-ray absorptiometry (DXA) correlated ex vivo with the micro architectural parameters. It is unknown if these microstructural correlations could be made in healthy premenopausal women. METHODS: Randomly selected women between 20-40 years of age were examined by DXA and HR-pQCT at the standard regions of interest and at customized sub regions to focus on cortical and trabecular parameters of strength separately. For cortical strength, at the distal tibia the volumetric cortical index was calculated directly from HR-pQCT and the areal cortical index was derived from the DXA scan using a Canny threshold-based tool. For trabecular strength, the trabecular bone score was calculated based on the DXA scan of the lumbar spine and was compared with the corresponding parameters derived from the HR-pQCT measurements at radius and tibia. RESULTS: Seventy-two healthy women were included (average age 33.8 years, average BMI 23.2 kg/m(2)). The areal cortical index correlated highly with the volumetric cortical index at the distal tibia (R  =  0.798). The trabecular bone score correlated moderately with the microstructural parameters of the trabecular bone. CONCLUSION: This study in randomly selected premenopausal women demonstrated that microstructural parameters of the bone evaluated by HR-pQCT correlated with the DXA derived parameters of skeletal regions containing predominantly cortical or cancellous bone. Whether these indexes are suitable for better predictions of the fracture risk deserves further investigation.