Modification of nanocellulose via atom transfer radical polymerization and its reinforcing effect in waterborne UV-curable resin.

Cellulose nanocrystals (CNCs) are green reinforcing materials, and their potential has been evaluated in the preparation of waterborne UV-curable resin composites with high-performance. Herein, we present a novel and scalable approach for preparing surface-modified CNCs with acrylic-based polymers to strengthen the compatibility and interaction between CNCs and UV-curable resins. Using tert-butyl acrylate as the monomer, the nanocellulose grafted copolymer CNC-g-PtBA was successfully synthesized via atom transfer radical polymerization (ATRP) in the presence of a macromolecular initiator. Then, the CNC-g-PtBA is blended into the acrylic resin as a nanofiller to prepare the UV-curable nanocomposite. The results indicated that the contact angle of the CNCs increased from 38.7° to approximately 74.8°, and their thermal stability was significantly improved after graft modification. This contributed to the effective alleviation of the agglomeration phenomenon of nanocomposites due to the high hydrophilicity of pure CNCs. Notably, not only was the UV curing efficiency of the nanocomposites greatly increased but the mechanical properties were also further enhanced. Specifically, with the addition of 0.5 wt% CNC-g-PtBA, the curing time of the nanocomposite was shortened from >30 mins down to approximately 6 mins, and the bending strength was increased from 10 MPa for the original resin and 5 MPa for the addition of pure CNCs to 14.3 MPa, and the bending modulus was also greatly increased (up to approximately 730 MPa). Compared to pure CNCs, they are compatible with the resin, exhibiting high mechanical strength and flexibility, and have virtually no effect on the light transmission of the nanocomposites. Additionally, dielectric analysis (DEA) was used to monitor the dielectric constant and conductivity of the UV-curable nanocomposites in real time to further characterize their curing kinetics. The permittivity of these nanocomposites increased by 125 % compared to pristine resin, which shows potential for applications in high dielectric composites or for improving electrical conductivity. This work provides a feasible method for preparing UV-curable nanocomposites with high curing efficiency and permittivity, realizing a wider application of this high-performance nanocomposite.

Properties of Poplar Fiber/PLA Composites: Comparison on the Effect of Maleic Anhydride and KH550 Modification of Poplar Fiber.

To improve the interfacial adhesion and dispersion of a poplar fiber in a polylactic acid (PLA) matrix, maleic anhydride (MA) and a silane coupling agent (KH550) were used to modify the poplar fiber. The poplar fiber/PLA composites were produced with different modifier contents. The mechanical, thermal, rheological, and physical properties of composites were investigated. A comparison of different natural fiber modifications on the properties of composites was also analyzed. The results showed that both MA and KH550 could improve the interfacial adhesion between the poplar fiber and PLA, resulting in the enhanced mechanical properties of the composite, with 17% and 23% increases of tensile strength for 0.5% MA and 2% KH550, respectively. The thermal properties of the composites were improved at 6% KH550 (a 9% enhancement of T90%) and decreased at 0.5% MA (a 6% decrement of T90%). The wettability of the composites obtained a 11.3% improvement at 4% KH550 and a 5% reduction at 4% MA. Therefore, factors such as mechanical properties, economic efficiency, and durability should be carefully considered when choosing the modifier to improve the property of the composite.

Activating CaCO3 to enhance lead removal from lead-zinc solution to serve as green technology for the purification of mine tailings.

Efficient lead removal from metal-containing wastewater, such as acid mine drainage (AMD), is an important step in environmental purification and secondary resources recovery. In this paper, a novel approach by mechanochemically activating CaCO3 through simply wet ball milling in metal-containing solution was developed, where selective Pb2+ precipitation in the form of PbCO3 was achieved based on its reaction with the CO32- from the activated CaCO3. By such milling operation, the removal efficiency of Pb2+ from aqueous solution could reach over 99%, while more than 99% Zn2+ (as well as Mn, Ni and Cd) was remaining in the solutions, demonstrating the feasibility and high effectiveness of precipitating Pb2+ and serving the purpose of recovering other metals without Pb impurity. The solubility differences between Pb carbonate and other carbonates of Zn, Mn, Ni or Cd were understood to be the main pathway and using CaCO3 would offer an easy operation and environmental friendly process to purify the metals-containing wastewater by precipitating Pb, compared with the difficulties when using alkaline neutralization to treat them. In addition, basic zinc carbonate (a zinc-containing ore waste) as an alternative precipitant to CaCO3 in the separation process was also confirmed to increase the zinc recovery in the solution while maintaining high Pb2+ removal efficiency.

Lignin-coated cellulose nanocrystal filled methacrylate composites prepared via 3D stereolithography printing: Mechanical reinforcement and thermal stabilization.

Various contents of lignin-coated cellulose nanocrystals (L-CNC) were incorporated into methacrylate (MA) resin and their mixture was used to prepare nanocomposites via 3D stereolithography (3D-SL) printing. Gaps were found between the L-CNC and MA matrix in 3D-SL printed nanocomposites before postcure. However, gaps decreased after postcure due to interactions between the L-CNC and MA molecules. Mechanical properties increased with the addition of 0.1% and 0.5% L-CNC after postcure, and the thermal stability was improved at 0.5% L-CNC. Dynamic mechanical analysis demonstrated that incorporation of L-CNC increased the storage modulus in the rubbery plateau. The loss factor had two transition regions, which gradually changed by merging together with increasing L-CNC content, and a broadening of the transition region was observed after postcure. In particular, the mechanical and thermal properties of 3D-SL printed nanocomposites, after postcure, exhibited higher improvement than those before postcure.